Avanti HRS88N1B Installation Manual

MODEL HRS88N1B

Your Avanti Room Security Safe is supplied with the following:

1 – Security Safe Unit
1 – Installation / Usage Guide

4 – 1.5V Batteries
Installation Screws

4 – Rubber Feet

INSTALLING YOUR SECURITY SAFE

SECURITY SAFE

INSTALLATION AND USAGE INSTRUCTIONS

2 – Emergency Access Keys

1 – Felt Liner

When installing your safe, be sure the location is sturdy enough to support the unit and is both
secure and easy to access.

Safe can be installed onto either a concrete or wooden surface.
When installing use a 25/64” (10mm) drill bit and screws.
To prevent removal of your security safe, it is recommended to use Allen type screws (not included)

to affix the unit to the installation location.

INITIAL SETUP AND CONFIGURATION.

RESETTING THE AD MINISTRATOR PASSWORD

successfully.

GUEST / USER CODE SETUP

Customer Hotline at 1-800 – 220 - 5570

After you have installed the unit in its final location, proceed to set up digital access controls.

1) Using the emergency Access Key, open the safe.

2) Open the battery compartment cover.

3) Following the image shown in the battery compartment install 4 AA sized batteries.

4) Close the battery compartment cover.

5) The words “ALL READY” will be displayed on the LCD display for approximately 1 second; the
security safe will then go into “STANDBY Mode”.

6) Once in “STANDBY Mode” the LCD display will show the date and time (YY, MM, DD).

7) Using the keypad, enter the initial setup password “1234” or the administrator password
“8888”.

NOTE:
Battery Life / Level indicator: The battery indicator on the LCD display will show the current status
of the batteries. Always replace all of the batteries at the same time. If at any time the battery level
is too low to operate the security safe, use the emergency access key.

Safety / Security Feature: If the passcode is entered incorrectly more than 3 times the keypad will
go into lock mode. After approximately (5) five minutes the keypad will return to normal working
function.

Interior Light: When the safe is unlocked using the keypad, the interior light will turn on and will
turn off automatically after approximately 45 seconds.

Automatic Door Opening: When the safe is unlocked using the keypad the door will automatically
open slightly outward to allow easy / quick access to contents stored in the safe.

To reset the acc ess code read and follow the steps below.

1) With the door open, enter a new 4 – 8 digit code and press the “#” key to confirm the new pass code.

2) You will hear and see the security lock engage and the word “CLOSE” will be displayed on the LCD
screen.

3) Enter the new pass code and press the “#” key again to open the security safe. The security lock will
disengage and the word “OPEN” will be displayed on the LCD screen.

4) Close the door and enter the new code set up in step # 1 and press the “#” key. The word “CLOSE”
will be displayed on the LCD screen a nd the security lock will engage.

5) If the Guest / User enters the wron g pass code three (3) times in a row the key pad will go into

security-lock mode and will remain locked for a pproximately (5) five minute s. A fter the (5) five
minutes has elapsed the keypad will return to normal operation.

To reset the acc ess code read and follow the steps below.

1) With the door open, press the “#” key to activate the keypad, then press the “0” key twice, then
press the “red” button on the battery compartment once to enter the programming mode.

2) Once in the programming mode you will hear a “DI” sound and “- - - -“ will be shown in the LCD
display.

3) Enter the new 4 – 8 administrator password and press the “#” key to confirm.

4) The word “INTO” will show on the LCD display to confirm the new password has been set

Avanti Products

Miami, FL 33172

In the event of service issues, p l ease call the