User Manual
User Manual
Avantco Continuous Feed Food Processor
5/2016
Model: CFP5D
Please read and keep these instructions. Indoor use only.
www.AvantcoEquipment.com 1
User Manual
Safety
1. The food processor must be managed by skilled personnel that are familiar with the instructions
for use and safety contained in this manual.
2. This machine comes with several safety systems but users must avoid setting their hands and loose
objects near the cutting discs and moving parts.
3. Before any cleaning and maintenance operations, check to make sure the machine is disconnected
from the power source.
4. Never use the food processor to with frozen food.
5. Never replace or repair parts on your own. Consult an authorized service agency.
6. Operate the processor on a clean, dry and level surface.
7. If the power cord is damaged, do not use. Contact the distributor for a replacement power cord.
Installation and Operation
1. Unpack your food processor and place on a clean, dry surface
2. Inspect the unit for damage, including the power cord. Do not use if any damage is found.
3. Locate the unit near a 110-120v 1phase outlet. If you are unsure of the electrical connection- contact
a qualified electrician before using.
4. It is recommended to clean the equipment prior to first use.
Use of the Equipment
Controls
1. Green button for starting the machine.
2. Red button for stopping the machine.
Setting the Discs on the Machine
Rotate the knob as shown in figure n.1 And open the cover. First set the plastic ejecting disc (2), then the disc
selected for the cutting on top of the plastic disc. Close the cover and reverse the rotation of the handle. Hit
the start button to automatically hook the discs in the correct position.
2 www.AvantcoEquipment.com
User Manual
Cover Opening (1) Disc Position (2)
Setting and Cutting the Food
Lift the handle and set the food inside the opening as shown in figure n.3, Then close the handle.
Press the green start button with your right hand, and with your left hand, lightly move the handle downwards
until food has passed through the hopper.
Lift the handle to add more food. The machine starts automatically when the handle is closed. Repeat these
operations as needed.
WARNING: NEVER USE YOUR HAND TO FEED ANYTHING THROUGH THE HOPPER
Release and Replacement of the Discs
Turn the handle and lift the cover. (Fig.1)
Turn the d
lift it by setting your hand under the disc.
(4) (5)
www.AvantcoEquipment.com 3
isc anticlockwise and cover the cutting edge with appropriate material as (rubber, fabric, etc), then
User Manual
Cleaning and Maintenance Operations
Before carrying out any cleaning or maintenance operations, check to make sure that the mains switch is off
and the plug disconnected.
Use a damp cloth and a non-abrasive detergent to clean the machine and discs.
The discs are dishwasher safe. Do not run the base unit in the dishwasher.
Never use steel wool or any abrasive chemicals on the discs or machine.
Technical Specifications
MODEL DIMENSIONS WEIGHT POWER ELECTRICAL RPM
CONNECTION
CFP5D 9”X22.5”X20” 51LBS 550 WATTS 110V 1 PHASE 270
60Hz
Wiring Diagram
110V
4 www.AvantcoEquipment.com
User Manual
Parts Diagram
Parts Key for Avantco Equipment CFP5D Continuous Feed
Food Processor - 120V
Parts Diagram # New Part Name Replacement Part Item#
1 Pusher Handle Bolt (2/Set)
2 Replacement Handle Grip
3 Nylon Handle Gasket and Screw
4 Pusher Head
5 Kidney-Shaped Hopper
6, 7, 8, 9, 10 Locking Knob
11 Disc, Slicing, Grating, or Dicing
12 Plastic Ejecting Disc
13, 14, 15, 16, 17, 18 Disc Stem Assembly
19 Disc Stem Bearing
20 Lid Knob Sheath
21 Belt Wheel
22 Bottom Housing
23 Electric Box
24 Bottom Board of Electric Box
25 Bottom Panel
26 Handle Magnet
27 Umbrella Bolt
28 Handle Sheath
29 Nut
30 Adjusting Bolt
31 Pusher
32 Magnet Seat
33 Magnet
34 Replacement Knife (Slicer Disc)
35 Top Housing
36 Microswitch
37 Lid Bolt
38 Power Switch
39 Strapped wheel
40 Belt
41 Motor 3/4 HP
42 Gasket
43 Gasket
44 Bolt
45 Gear Cover
46 Leg Bolt
177PCFPBOLT
177PCFPBAR
177PCFPGSKT
177PCFPUSH
177PCFPKNOB
177CGRATE18 (1/8" Grate)
177CGRATE516 (5/16" Grate)
177CGRATE532 (5/32" Grate)
177CSLICE38 (3/8" Slice)
177CSLICE516 (5/16" Slice)
177CSLICE532 (5/32" Slice)
177CSLICE564 (5/64" Slice)
177KITD38 (3/8" Dice Set)
177KITD516 (5/16" Dice Set)
177KITFRY38 (3/8" French Fry Set)
177KITFRY516 (5/16" French Fry Set)
177CDICE516 (5/16” Dicing Grid)
177CFF38 (3/8” French Fry Grid)
177CFF516 (5/16” French Fry Grid)
177CDICE38 (3/8” Dicing Grid)
177PCFPDDISC
177PCFPSTEM
177MGSTOMP
177PCFPMICSW
177PCFPWBOLT
177PCFPSWTCH
177PCFPBELT
177PFCPMOTOR
www.AvantcoEquipment.com 5
User Manual
Limited Warranty
All equipment, which is sold under Avantco trademark and used for commercial purpose is
warranted against defects in materials and workmanship. The warranty runs for six months from the
date of original installation and is for the benefit of the original purchaser only. All other Warranties,
Expressed or Implied, Statutory or Otherwise, including Withoutimitation any implied Warranty of
Merchantability or Fitness for Purposes are excluded. The Seller shall in no event be liable for direct,
indirect or consequential damages in connection with Avantco commercial products.
This warranty is not effective if damage occurs because of accident, carelessness, improper
installation, lack of proper set – up, supervision when required or if the equipment is installed
or operated in any manner contrary to thE installation and operating instructions. In these
cases, repairs will be made at a reasonable cost. Work performed by unauthorized personnel or
unauthorized service agencies voids this Warranty.
This warranty does not apply to, and Avantco is not responsible for, any warranty claims made on
products sold or used outside of the United States.
6 www.AvantcoEquipment.com
Loading...