Part No. E2017OT21A2R
OFT-10W01
10.1" Open Frame Tablet
Quick Reference Guide
1
st
Ed –05 January 2016
Copyright Notice
Copyright 2016 Avalue Technology Inc., ALL RIGHTS RESERVED.
OFT-10W01
2 OFT-10W01 Quick Reference Guide
FCC Statement
THIS DEVICE COMPLIES WITH PART 15 FCC RULES. OPERATION IS
SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE.
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING
INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS
FOR A CLASS "A" DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES.
THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST
HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A
COMMERCIAL ENVIRONMENT. THIS EQUIPMENT GENERATES, USES, AND CAN
RADIATE RADIO FREQUENCY ENERGY AND, IF NOT INSTATLLED AND USED IN
ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL
INTERFERENCE TO RADIO COMMUNICATIONS.
OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE
HARMFUL INTERFERENCE IN WHICH CASE THE USER WILL BE REQUIRED TO
CORRECT THE INTERFERENCE AT HIS OWN EXPENSE.
Caution
Note: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Notice:
(1) A Unshielded-type power cord is required in order to meet FCC emission limits and also
to prevent interference to the nearby radio and television reception. It is essential that only
the supplied power cord by used.
(2) Use only shielded cables to connect I/O devices to this equipment.
(3) Changes or modifications not expressly approved by the party responsible for
Quick Reference Guide
OFT-10W01 Quick Reference Guide
3
compliance could void the user’s authority to operate the equipment.
RF exposure caution:
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. & This device and its antenna(s) must not be co-located or
conjunction with any other antenna or transmitter
RF exposure caution:
This Wireless LAN radio device has been evaluated under FCC Bulletin OET 65 and found
compliant to the requirements as set forth in CFR 47 Sections 2.1091, 2.1093, and 15.247
(b) (4) addressing RF Exposure from radio frequency devices. The radiated output power of
this Wireless LAN device is far below the FCC radio frequency exposure limits.
Nevertheless, this device shall be used in such a manner that the potential for human
contact during normal operation is minimized.
A Message to the Customer
Avalue Customer Services
Each and every Avalue’s product is built to the most exacting specifications to ensure
reliable performance in the harsh and demanding conditions typical of industrial
environments. Whether your new Avalue device is destined for the laboratory or the factory
floor, you can be assured that your product will provide the reliability and ease of operation
for which the name Avalue has come to be known.
Your satisfaction is our primary concern. Here is a guide to Avalue’s customer services. To
ensure you get the full benefit of our services, please follow the instructions below carefully.
Technical Support
We want you to get the maximum performance from your products. So if you run into
technical difficulties, we are here to help. For the most frequently asked questions, you can
easily find answers in your product documentation. These answers are normally a lot more
detailed than the ones we can give over the phone. So please consult the user’s manual
first.
To receive the latest version of the user’s manual; please visit our Web site at:
http://www.avalue.com.tw/
OFT-10W01
4 OFT-10W01 Quick Reference Guide
Content
1. Getting Started ............................................................................................................ 5
1.1 Safety Precautions ................................................................................................ 5
1.2 Packing List ........................................................................................................... 5
1.3 System Specifications ........................................................................................... 6
1.4 System Overview ................................................................................................... 8
1.4.1 Right View .................................................................................................................................... 8
1.4.2 Left View ...................................................................................................................................... 8
1.5 System Dimensions ............................................................................................... 9
1.5.1 Front and Rear side ..................................................................................................................... 9
1.5.2 Installing Extend Brackets .......................................................................................................... 10
1.5.3 Front and Rear side (With Extend Bracket) ............................................................................... 11
1.6 Flush Mounting Concept ...................................................................................... 12
1.7 Wall Mounting Concept ........................................................................................ 13
2. Hardware Configuration ........................................................................................... 14
2.1 Architecture Overview—Block Diagram ............................................................... 15
2.2 BCX11 Overviews ................................................................................................ 16
2.3 BCX11 Connector list ........................................................................................... 18
2.4 BCX11 Connectors settings ................................................................................. 20
2.4.1 Touch button board connector (JTB1) ........................................................................................ 20
2.4.2 General purpose I/O connector (JDIO1) ..................................................................................... 20
2.4.3 RS-232 connector (J232-1) ......................................................................................................... 21
2.4.4 RS-485 connector (J485-1) ......................................................................................................... 21
2.4.5 USB connector (JCAM1) ............................................................................................................. 22
2.4.6 AMPLIFIER_L (JAMP_L) ............................................................................................................ 22
2.4.7 AMPLIFIER_R (JAMP_R) ........................................................................................................... 23
2.4.8 A-MIC connector (JAMIC1) ......................................................................................................... 23
2.4.9 I2C connector (JSEN1) ............................................................................................................... 24
2.5 Antenna Assembly and Cable Routing ................................................................ 25
2.6 Android Rotate Setting ......................................................................................... 30
Quick Reference Guide
OFT-10W01 Quick Reference Guide
5
1. Getting Started
1.1 Safety Precautions
Warning!
Always completely disconnect the power cord from your
chassis whenever you work with the hardware. Do not
make connections while the power is on. Sensitive
electronic components can be damaged by sudden power
surges. Only experienced electronics personnel should
open the PC chassis.
Caution!
Always ground yourself to remove any static charge before
touching the CPU card. Modern electronic devices are very
sensitive to static electric charges. As a safety precaution,
use a grounding wrist strap at all times. Place all electronic
components in a static-dissipative surface or static-shielded
bag when they are not in the chassis.
1.2 Packing List
1 x OFT-10W01 Open Frame Tablet
OFT-10W01
6 OFT-10W01 Quick Reference Guide
1.3 System Specifications
Board Specification
Processor
Intel Atom Z3735F
System Memory
2GB DDR3L RAM
Storage
8GB or 32GB eMMC
RF
WIFI
WIFI 802.11 b/g/n/
System Specification
Internal I/O
MIO
1 x RS232 (TX/RX) / RS485 header
1 x 16 bit GPIO header
1 x USB header
1 x I2C header (Optional)
1 x eDP & Dual channel 24bit LVDS
1 x backlight control & power
2 x speaker header (1.2W stereo)
1 x A-MIC header
1 x Touch Button connector header
1 x DC input 4pin header
External I/O
USB
2 x USB 2.0
1 x micro USB Client (Android only)
LAN
1 x 10/100 Ethernet
Display
1 x HDMI
Audio
1 x Head phone jack
SD
1 x Micro SD slot
Power-in
1 x DC jack
Mechanical & Environmental
Power
Requirement
19V DC input
Optional 12V or 24V DC input
Power Type
DC Jack
DC input 4pin header
Optional POE 802.3AT (10” only)
Operating Temp.
0°C ~ 40°C
Storage Temp.
-20°C ~ 60°C
Operating
Humidity
0% ~ 90% Relative Humidity, Non-condensing
Quick Reference Guide
OFT-10W01 Quick Reference Guide
7
LCD Characters
Panel
Resolution
1280 x 800
Luminance
350
View Angle
(H+-/V+-)
85°/85°
Touch
Touch
PCAP
Surface
hardness
6H
Note: Specifications are subject to change without notice.
OFT-10W01
8 OFT-10W01 Quick Reference Guide
1.4 System Overview
1.4.1 Right View
1.4.2 Left View
Connectors
Label
Function
Note
HP
Audio line-out connector
HDMI
HDMI connector
USB
2 x USB 2.0 connector
DCIN
DC power-in connector
SD
Micro SD card slot
Micro USB
Micro USB connector
LAN
RJ-45 Ethernet
Quick Reference Guide
OFT-10W01 Quick Reference Guide
9
1.5 System Dimensions
1.5.1 Front and Rear side
(Unit: mm)
OFT-10W01
10 OFT-10W01 Quick Reference Guide
1.5.2 Installing Extend Brackets
Step1. Locate brackets on both sides, matching the holes on the monitor.
Step2. Insert and fasten 16 screws on each side of the monitor to secure Mounting brackets.
Quick Reference Guide
OFT-10W01 Quick Reference Guide
11
1.5.3 Front and Rear side (With Extend Bracket)
(Unit: mm)
OFT-10W01
12 OFT-10W01 Quick Reference Guide
1.6 Flush Mounting Concept
Quick Reference Guide
OFT-10W01 Quick Reference Guide
13
1.7 Wall Mounting Concept
OFT-10W01
14 OFT-10W01 Quick Reference Guide
2. Hardware
Configuration
For advanced information, please refer to:
1- BCX11 included in this manual.
Note: If you need more information, please visit our website:
http://www.avalue.com.tw
Quick Reference Guide
OFT-10W01 Quick Reference Guide
15
2.1 Architecture Overview—Block Diagram
The following block diagram shows the architecture and main components of BCX11.
OFT-10W01
16 OFT-10W01 Quick Reference Guide
2.2 BCX11 Overviews
Quick Reference Guide
OFT-10W01 Quick Reference Guide
17
OFT-10W01
18 OFT-10W01 Quick Reference Guide
2.3 BCX11 Connector list
Connectors
Label
Function
Note
JHP1
Audio line-out connector
JHDMI1
HDMI connector
JUSB1/2
2 x USB 2.0 connector
JRJ45
RJ-45 Ethernet connector
JDCIN2
DC Power-in connector
JDCIN3
DC Power-in connector
J10TP1
10” Touch connector
J19TP1
21” Touch connector
J19BL1
21” back light connector
J10LCD
10” LCD connector
J15LCD
15” LCD connector
J19LCD
21” LCD connector
JDPUP1
Debug Port
JSD1
Micro SD card slot
JRTC
RTC battery connector
JSEN1
I2C connector
JUUSB1
Micro USB connector
JDIO1
General purpose I/O connector
JCAM1
USB connector
J485-1
RS-485 connector
J232-1
RS-232 connector
JTB1
Touch button board connector
JAMP_L
AMPLIFIER_L
JAMP_R
AMPLIFIER_R
JAMIC1
A-MIC connector
JECDB
EC Debug connector
JDB1
Debug connector
Quick Reference Guide
OFT-10W01 Quick Reference Guide
19
*Ethernet LED behavior:
Label
LED color
Indication
Meaning
Data Rate
Yellow
LED off
10 Mbits/sec data rate is selected
LED on
100 Mbits/sec data rate is selected
Link/ACT
Green
off
LAN link is not established
LED on
LAN link is established
LED Blinking
LAN active is occurring
*RTC Battery
Warning: Risk of Explosion if Battery is replaced by an Incorrect Type. Dispose of Used Batteries According to
the Instructions."
Attention: Risque d'explosion si la batterie est remplacée par un type incorrect. Jetez les piles usagées selon
les instructions.
OFT-10W01
20 OFT-10W01 Quick Reference Guide
2.4 BCX11 Connectors settings
2.4.1 Touch button board connector (JTB1)
Signal
PIN
PIN
Signal
PWR_JTB1
1 2 GND
NC
3 4 BU1_TV_3V
VOL_UP_3V
5 6 VOL_DOWN_3V
PWRBTN_3V
7 8 BU_BR+_3V
BU_BR-_3V
9
10
BU7_3V
LED_GREEN_con
11
12
LED_ORANGE_con
2.4.2 General purpose I/O connector (JDIO1)
Signal
PIN
PIN
Signal
DIO_GP20
1 2 DIO_GP10
DIO_GP21
3 4 DIO_GP11
DIO_GP22
5 6 DIO_GP12
DIO_GP23
7 8 DIO_GP13
DIO_GP24
9
10
DIO_GP14
DIO_GP25
11
12
DIO_GP15
DIO_GP26
13
14
DIO_GP16
DIO_GP27
15
16
DIO_GP17
I2C_0_SDA_5V
17
18
I2C_0_SCL_5V
+V5S_DIO
19
20
GND
Quick Reference Guide
OFT-10W01 Quick Reference Guide
21
2.4.3 RS-232 connector (J232-1)
Signal
PIN
DEBUG_TXD
1
DEBUG_RXD
2
NC 3 NC
4
GND
5
2.4.4 RS-485 connector (J485-1)
Signal
PIN
485_422TX1-
1
485_422TX1+
2
+5V_DEV
3
NC 4 NC
5
GND
6
OFT-10W01
22 OFT-10W01 Quick Reference Guide
2.4.5 USB connector (JCAM1)
Signal
PIN
+5V_UUSB
1
USB20_N0_CAM_R
2
USB20_P0_CAM_R
3
GND
4
GND
5
2.4.6 AMPLIFIER_L (JAMP_L)
Signal
PIN
SPKL_P
1
SPKL_M
2
Quick Reference Guide
OFT-10W01 Quick Reference Guide
23
2.4.7 AMPLIFIER_R (JAMP_R)
Signal
PIN
SPKR_P
1
SPKR_M
2
2.4.8 A-MIC connector (JAMIC1)
Signal
PIN
NC 1 NC
2
IN2P
3
IN2N
4
GND
5
OFT-10W01
24 OFT-10W01 Quick Reference Guide
2.4.9 I2C connector (JSEN1)
Signal
PIN
GND
5
SENSOR_INT_R
4
I2C_2_SCL_SENSOR
3
I2C_2_SDA_SENSOR
2
+3.3VA_SENSOR
1
Quick Reference Guide
OFT-10W01 Quick Reference Guide
25
2.5 Antenna Assembly and Cable Routing
In order to exert the antenna efficiency, the antenna body should be well fixed, well
grounding, and pasted at the correct location in the device.
1. The antenna body needs to well affixed on the case and avoid floating
2. If the case contained the carbon fiber or the metals, please keep more than 3 mm
spacing for antenna and avoid the overlapping.
3. The distance has to be retained for 5 mm between two adjacent antennas.
4. The Cu foil (Al foil) of the antenna has to be pasted on the large grounding. (For example:
the metal back of the LCD / The large area Al Foil of NB A cover)
5. The antenna body should be pasted on the non-metallic region and retained the require
clearance area.
6. The WiFi antenna body should be lifted up at least 7 mm by sponge while it is pasted on
a large ground plane.
Cable Routing: The antenna cable should be fixed secure in order to avoid crimping,
cramping, and lifted up.
1. The antenna cable should be fixed well, in order to prevent the impact for the antenna
efficiency. Avoiding the cable to cover the antenna body and cross under module.
2. At the same time, the cable routing should be avoided too close to the LVDS cable,
power cable and even interwined.
3. The cable could not thread under the connector of the cable field, and the routing also
could not under the connector, to avoid the connector floating to cause the poor connect.
4. The trench structure need ME help to design for fixed cable.
5. The connector of the antenna cable can not be a knuckle. Antenna cable minimum bend
radius can not less than 5 mm.
The antenna body needs to well affixed on the case and avoid floating.
OFT-10W01
26 OFT-10W01 Quick Reference Guide
If the case contained the carbon fiber or the metals, please keep more than 3 mm
spacing for antenna and avoid the overlapping.
The distance has to be retained for 5 mm between two adjacent antennas.
The Cu foil (Al foil) of the antenna has to be pasted on the large grounding. (For
example: the metal back of the LCD / The large area AL Foil of NB A cover)
Quick Reference Guide
OFT-10W01 Quick Reference Guide
27
The antenna body should be pasted on the non-metallic region and retained the
require clearance area.
The WiFi antenna body should be lifted up at least 7 mm by sponge while it is pasted
on a large grounding plane.
OFT-10W01
28 OFT-10W01 Quick Reference Guide
The antenna cable should be fixed well, in order to prevent the impact for the
antenna efficiency. Avoiding the cable to cover the antenna body and cross under
module.
At the same time, the cable routing should be avoided too close to the LVDS cable,
power cable and even interwined.
Quick Reference Guide
OFT-10W01 Quick Reference Guide
29
The cable could not thread under the connector of the cable field, and the routing
also could not under the connector, to avoid the connector floating to cause the poor
connect.
The trench structure need ME help to design for fixed cable.
The connector of the antenna cable can not be a knuckle. Antenna cable minimum
bend radius can not less than 5 mm.
OFT-10W01
30 OFT-10W01 Quick Reference Guide
2.6 Android Rotate Setting
Landscape/portrait mode rotate setting:
Default rotation is 0° rotate 90°/180°/270° Power offRestart
Quick Reference Guide
OFT-10W01 Quick Reference Guide
31
OFT-10W01
32 OFT-10W01 Quick Reference Guide
Loading...