Page 1
Part No. E2017ERSEA1R
ERS-CDVE
Fanless Intel® Atom™ D2550 Rugged Embedded
System with Intel® NM10 Express Chipset
Quick Reference Guide
2nd Ed –25 July 2013
Copyright Notice
Copyright 2013 Avalue Technology Inc., ALL RIGHTS RESERVED.
Page 2
ERS-CDVE
2 ERS-CDVE Quick Reference Guide
FCC Statement
THIS DEVICE COMPLIES WITH PART 15 FCC RULES. OPERATION IS
SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE.
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING
INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS
FOR A CLASS "A" DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES.
THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST
HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A
COMMERCIAL ENVIRONMENT. THIS EQUIPMENT GENERATES, USES, AND CAN
RADIATE RADIO FREQUENCY ENERGY AND, IF NOT INSTALLED AND USED IN
ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL
INTERFERENCE TO RADIO COMMUNICATIONS.
OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE
HARMFUL INTERFERENCE IN WHICH CASE THE USER WILL BE REQUIRED TO
CORRECT THE INTERFERENCE AT HIS OWN EXPENSE.
Copyright Notice
Copyright 2013 Avalue Technology Inc., ALL RIGHTS RESERVED.
No part of this document may be reproduced, copied, translated, or transmitted in any form
or by any means, electronic or mechanical, for any purpose, without the prior written
permission of the original manufacturer.
Disclaimer
Avalue Technology Inc. reserves the right to make changes, without notice, to any product,
including circuits and/or software described or contained in this manual in order to improve
design and/or performance. Avalue Technology assumes no responsibility or liability for the
use of the described product(s), conveys no license or title under any patent, copyright, or
masks work rights to these products, and makes no representations or warranties that
these products are free from patent, copyright, or mask work right infringement, unless
otherwise specified. Applications that are described in this manual are for illustration
purposes only. Avalue Technology Inc. makes no representation or warranty that such
application will be suitable for the specified use without further testing or modification.
Page 3
Quick Reference Guide
ERS-CDVE Quick Reference Guide
3
CONTENT
1. Getting Started ............................................................................................................ 5
1.1 Safety Precautions ................................................................................................ 5
1.2 Packing List ........................................................................................................... 5
1.3 System Specifications ........................................................................................... 6
1.4 System Overview ................................................................................................... 8
1.4.1 Front & Top View ......................................................................................................................... 8
1.4.2 Front View .................................................................................................................................... 9
1.4.3 Rear View ..................................................................................................................................... 9
2. Hardware Configuration ........................................................................................... 11
2.1 ERS-CDVE connector mapping........................................................................... 12
2.1.1 External Serial Port 1/3/4/5/6/7/8/9/10 connector (COM1/3/4/5/6/7/8/9/10) .............................. 12
2.1.2 VGA connector (VGA) ................................................................................................................ 12
2.1.3 LPT connector (LPT Port) .......................................................................................................... 13
2.1.4 LVDS connector (LVDS Port) .................................................................................................... 13
2.1.4 Multi-Function Port combined COM2, 2 PS/2, Audio, GPIO and SMBus (Multi-function port) . 14
2.1.4.1 GPIO+SMBUS ....................................................................................................................... 15
2.1.4.2 COM2 .................................................................................................................................... 15
2.2 EBM-CDVS and AUX-M03 Overviews ................................................................ 16
2.2.1 EBM-CDVS ................................................................................................................................ 16
2.2.2 AUX-M03 .................................................................................................................................... 18
2.3 EBM-CDVS Jumper & Connector list .................................................................. 18
2.4 AUX-M03 Connector list ...................................................................................... 19
2.5 EBM-CDVS Jumpers & Connectors settings ....................................................... 20
2.5.1 Clear CMOS (CMOS1) .............................................................................................................. 20
2.5.2 COM 1/2 pin 9 signal select (JRI1/2) ......................................................................................... 20
2.5.3 LPC port connector (LPC1) ........................................................................................................ 21
2.5.4 Power connector (PWR1) .......................................................................................................... 21
2.5.5 LCD inverter connector (BKL1) .................................................................................................. 22
2.5.6 LCD backlight brightness adjustment (JVR) .............................................................................. 22
2.5.7 SPI connector (SPI1) ................................................................................................................. 23
2.5.8 Front Panel Connector 1 (CN1) ................................................................................................. 23
2.5.9 Front Panel Connector 2 (CN2) ................................................................................................. 24
2.5.10 DC Output connector (DCOUT_S) ........................................................................................ 24
2.5.11 AT/ATX mode selector (SW1) ............................................................................................... 25
2.5.11.1 Signal Description –AT/ATX mode selection ................................................................................... 25
2.6 AUX-M03 Connectors settings ............................................................................ 26
Page 4
ERS-CDVE
4 ERS-CDVE Quick Reference Guide
2.6.1 System reset (WCN1) ................................................................................................................ 26
2.6.2 LPT Port (WJPRT1) ................................................................................................................... 26
2.7 Installing Mounting Brackets (ERS-CDVE) .......................................................... 27
2.8 Installing Hard Disk & Memory, PCI devices (ERS-CDVE) ................................. 28
Page 5
Quick Reference Guide
ERS-CDVE Quick Reference Guide
5
1. Getting Started
1.1 Safety Precautions
Warning!
Always completely disconnect the power cord from your
chassis whenever you work with the hardware. Do not
make connections while the power is on. Sensitive
electronic components can be damaged by sudden power
surges. Only experienced electronics personnel should
open the PC chassis.
Caution!
Always ground yourself to remove any static charge before
touching the CPU card. Modern electronic devices are very
sensitive to static electric charges. As a safety precaution,
use a grounding wrist strap at all times. Place all electronic
components in a static-dissipative surface or static-shielded
bag when they are not in the chassis.
1.2 Packing List
1 x ERS-CDVE Fanless Intel® Atom™ D2550 Rugged Embedded
System with Intel® NM10 Express Chipset
1 x Quick Reference Guide
1 x DVD-ROM contains the followings:
— User’s Manual (this manual in PDF file)
— Ethernet driver and utilities
— VGA drivers and utilities
— Audio drivers and utilities
Other major components include the followings:
— 44-Pin Multiple Function Cable
— Wall Mount Bracket
— Adapter
— Power Cord
— Screw kit for Wall Mount/Mini Card/2.5” Drive Bay
Page 6
ERS-CDVE
6 ERS-CDVE Quick Reference Guide
1.3 System Specifications
System
Board
EBM-CDVS + AUX-M03
CPU
Onboard Intel® Atom™ D2550 1.86GHz CPU
BIOS
AMI 16Mbit SPI BIOS
System Chipset
Intel® NM10 Express Chipset
I/O Chip
Nuvoton W83627DHG-P
System Memory
One 204-pin DDR3 SODIMM Socket Up to 4GB DDR3
800/ 1066 SDRAM
Storage
1 x 2.5” Drive Bay, 1 x mSATA
Watchdog Timer
Reset: 1sec. ~ 65535sec./min. and 1sec. or 1min./step
H/W Status Monitor
Monitoring System Temperature and Voltage with
Auto Throttling Control
Expansion Interface
2 x Mini PCIe Socket
(mSATA on 1st, SIM Card Slot on 2nd)
External I/O
COM
10 x RS-232 (COM1 ~ COM4 Can be Set as 422/485 by BIOS);
COM3 ~ COM10 Supports Isolation Protection
LAN
1 x RJ-45
Antenna
2 Knockouts for Antenna Mounting
(Options to Add WiFi & 3G)
VGA
1 x VGA
Audio Port
Mic-in, Line-in, Line-out
GPIO
6-bit GPI and 6-bit GPO
USB Port
5 x USB 2.0 (Front 1; Rear 4)
PS/2
2 x PS/2 for KB & MS
SIM
1 x SIM Card Slot
SMBUS
1 x SMBUS
DC Output
2-Pin Phoenix (Voltage is Identical with DC-Input)
LPT
1 x DB-25
LVDS
1 x Dual-channel 18/ 24-bit LVDS
Display
Chipset
Intel® Cedarview Integrated Graphics
Resolution
CRT Mode: 1920 x 1200 @ 60Hz
Audio
Audio Chipset
Realtek ALC892 Supports 5.1-CH Audio
Audio Interface
Line-in, Line-out and Mic-in
Page 7
Quick Reference Guide
ERS-CDVE Quick Reference Guide
7
Ethernet
LAN Chip
1 x Intel® 82574L Gigabit Ethernet
Ethernet Interface
10/ 100/ 1000 Base-Tx Gigabit Ethernet Compatible
Environment & Mechanical
Power Requirement
+12 ~ +26Vdc (Lockable DC Jack)
ACPI
Single Power ATX Support S0, S3, S4, S5
ACPI 3.0 Compliant
Power Mode
AT/ ATX (ATX is The Default Setting)
Operating Temperature
-10 ~ 60°C (w/ mSATA and 2.5” SSD), Ambient w/Air Flow
Storage Temperature
-40 ~ 75°C (-40 ~ 167°F)
Relative Humidity
0% ~ 90% Relative Humidity, Non-condensing
Vibration Protection
With mSATA/ SSD: 5Grms, IEC 60068-2-64, Random,
10 ~ 500Hz, 1hr/axis
Shock Protection
With mSATA/ SSD: 50G, IEC 60068-2-27, Half Sine,11ms
Certification
CE, FCC Class B
Dimension (W x D x H)
231mm x 160mm x 80mm
Weight
7.7lbs (3.5Kgs)
Page 8
ERS-CDVE
8 ERS-CDVE Quick Reference Guide
1.4 System Overview
1.4.1 Front & Top View
Page 9
Quick Reference Guide
ERS-CDVE Quick Reference Guide
9
1.4.2 Front View
1.4.3 Rear View
Page 10
ERS-CDVE
10 ERS-CDVE Quick Reference Guide
Connectors
Label
Function
Note
COM1
Serial port connector 1
COM3~10
Serial port connector 3~10
DC-IN
DC power-in connector
DC-OUT
DC power-out connector
LAN
RJ-45 Ethernet
44-pin Multi-function
Multi-Function Port combined COM2,
2 PS/2, Audio, GPIO and SMBus
USB
USB connector
VGA
VGA connector
Swappable Drawer
2.5” Driver Bay and SIM Card
LPT Port
LPT connector
LVDS Port
LVDS connector
Power Switch
Power-in connector
Page 11
Quick Reference Guide
ERS-CDVE Quick Reference Guide
11
2. Hardware
Configuration
Jumper and Connector Setting, Driver and BIOS Installing
For advanced information, please refer to:
1- EBM-CDVS and AUX-M03 included in this manual.
Note: If you need more information, please visit our website:
http://www.avalue.com.tw
Page 12
ERS-CDVE
12 ERS-CDVE Quick Reference Guide
2.1 ERS-CDVE connector mapping
2.1.1 External Serial Port 1/3/4/5/6/7/8/9/10 connector (COM1/3/4/5/6/7/8/9/10)
-
Signal
PIN
PIN
Signal
NDCDA#_485TXN
1 6 NDSRA#
NRXDA#_485TXP
2 7 NRTSA#
NTXDA#_485RXP
3 8 NCTSA#
NDTRA#_485RXN
4 9 NRIA#
GND
5
2.1.2 VGA connector (VGA)
PIN
Signal
PIN
Signal
PIN
Signal
1
RED
6
GND
11
NC
2
GREEN
7
GND
12
SDT_DDC
3
BLUE
8
GND
13
VGA_HS
4
NC 9 +5V
14
VGA_VS
5
GND
10
GND
15
SCK_DDC
Page 13
Quick Reference Guide
ERS-CDVE Quick Reference Guide
13
2.1.3 LPT connector (LPT Port)
Signal
PIN
PIN
Signal
STB-
1
14
LPT_AFD#
PD0
2
15
LPT_ERR#
PD1
3
16
LPT_INIT#
PD2
4
17
LPT_SLIN#
PD3
5
18
GND
PD4
6
19
GND
PD5
7
20
GND
PD6
8
21
GND
PD7
9
22
GND
LPT_ACK#
10
23
GND
LPT_BUSY
11
24
GND
LPT_PE
12
25
GND
LPT_SLCT
13
2.1.4 LVDS connector (LVDS Port)
PIN
Signal
PIN
Signal
PIN
Signal 1 3.3V
16
LVDS_DATA2_P
31
NC 2 3.3V
17
LVDS_DATA2_N
32
NC 3 GND
18
GND
33
GND
4
LVDS_DDC_DATA
19
LVDS_DATA3_P
34
LVDS_CLKP
5
LVDS_DDC_CLK
20
LVDS_DATA3_N
35
LVDS_CLKN
6
GND
21
GND
36
GND
7
LVDS_DATA0_P
22
LVDS_DATA3_P
37
NC
8
LVDS_DATA0_N
23
LVDS_DATA3_N
38
NC 9 GND
24
GND
39
GND
10
LVDS_DATA1_P
25
NC
40
BKL1_5V
11
LVDS_DATA1_N
26
NC
41
BKL1_Bright
12
GND
27
GND
42
BKL1_BKLTEN
13
12V
28
NC
43
BKL1_GND
14
5V
29
NC
44
BKL1_12V
15
5V
30
GND
Page 14
ERS-CDVE
14 ERS-CDVE Quick Reference Guide
2.1.4 Multi-Function Port combined COM2, 2 PS/2, Audio, GPIO and SMBus
(Multi-function port)
PIN
Signal
PIN
Signal
PIN
Signal
1
LINE1_JD
16
FRONT_JD
31
LINE1_RIN
2
MIC1_JD
17
LINEOUT_R
32
GND
3
MIC_RIN
18
GND
33
LINE1_LIN
4
GND
19
LINEOUT_L
34
+5V
5
MIC_LIN
20
GND
35
DO3
6
DO5
21
DO4
36
DO0
7
DO2
22
DO1
37
DI3
8
DI5
23
DI4
38
DI0
9
DI2
24
DI1
39
SMB_CLK
10
MSCK
25
SMB_DATA
40
NRIB#
11
GND
26
GND
41
NRTSB#
12
MSDA
27
NCTSB#
42
COM2_GND
13
KBDA
28
NDSRB#
43
NTXDB_485RXP
14
VCC_PS2
29
NDTRB#_485RXN
44
NDCDB#_485TXN
15
KBCK
30
NRXDB_485TXP
Page 15
Quick Reference Guide
ERS-CDVE Quick Reference Guide
15
2.1.4.1 GPIO+SMBUS
Signal
PIN
PIN
Signal
25
13
24
12
23
11
22
10 SMBUS_DATA
21 9
SMBUS_CLK
20 8 GND
GPI-D5
19 7 5V
GPI-D4
18 6 GPO-D5
GPI-D3
17 5 GPO-D4
GPI-D2
16 4 GPO-D3
GPI-D1
15 3 GPO-D2
GPI-D0
14 2 GPO-D1
1 GPO-D0
2.1.4.2 COM2
Signal
PIN
PIN
Signal
DSR
6 1 DCD
RTS
7 2 RxD
CTS
8 3 TxD
RI
9 4 DTR
5
GND
Page 16
ERS-CDVE
16 ERS-CDVE Quick Reference Guide
2.2 EBM-CDVS and AUX-M03 Overviews
2.2.1 EBM-CDVS
Page 17
Quick Reference Guide
ERS-CDVE Quick Reference Guide
17
Page 18
ERS-CDVE
18 ERS-CDVE Quick Reference Guide
2.2.2 AUX-M03
2.3 EBM-CDVS Jumper & Connector list
Jumpers
Label
Function
Note
CMOS1
Clear CMOS
3 x 1 header, pitch 2.54mm
JRI1/2
COM 1/2 pin 9 signal select
3 x 2 header, pitch 2.00mm
Connectors
Label
Function
Note
USB_REAR
USB connector
USB_FRONT
USB connector
LAN1
LAN connector
CRT1
VGA connector
DB-44
Multi-function port
1. COM2
2. Audio(line-in, line-out,
mic-in)
3. 2 x PS/2 for KB/MS,
4. 12 bit GPIO/SMBUS
COM1
Serial port connector 1
DCJACK
DC-IN connector
Page 19
Quick Reference Guide
ERS-CDVE Quick Reference Guide
19
MPCIE1/2
Mini PCI Express connector 1/2
52 pin
PWR1
Power connector
PWRBTN
Power button
RSTBTN
Reset button
LED_PWR
LED Power
LED_HD
LED HDD
LED_ACK
LED LAN
LED_SPD_LNK
LED LAN
SIMCARD
SIM card slot
LVDS1
LVDS connector
SODIMM1
DDR3 SODIMM connector
MIOE_CB
IET Expansion slot
LPC1
Low pin count interface
7 x 2 header, pitch 2.00 mm
SPI1
SPI connector
4 x 2 header, pitch 2.00 mm
PWR1
Power connector
4 x 1 wafer, pitch 2.50 mm
BKL1
LCD inverter connector
5 x 1 wafer, pitch 2.00 mm
JVR
LCD backlight brightness adjustment
3 x 1 header, pitch 2.54 mm
CN1
Front Panel Connector 1
5 x 1 wafer, pitch 2.00 mm
CN2
Front Panel Connector 2
8 x 1 wafer, pitch 2.00 mm
DCOUT_S
DC Output connector
6 x 1 wafer, pitch 2.00 mm
SW1
AT/ATX mode selector
2.4 AUX-M03 Connector list
Connectors
Label
Function
Note
WRSTBTN1
Reset button
WJPRT1
LPT Port
13 x 2 header, pitch 2.00mm
WCN1
System reset
2 x 1 wafer, pitch 2.50mm
WUSB_REAR
USB connector
COM3_7
Serial port connector 3 & 7
COM4_8
Serial port connector 4 & 8
COM5_9
Serial port connector 5 & 9
COM6_10
Serial port connector 6 & 10
WMIOE_IO
IET Expansion slot
Page 20
ERS-CDVE
20 ERS-CDVE Quick Reference Guide
2.5 EBM-CDVS Jumpers & Connectors settings
2.5.1 Clear CMOS (CMOS1)
*Default
Protect*
Clear CMOS
2.5.2 COM 1/2 pin 9 signal select (JRI1/2)
* Default
Ring*
+5V
+12V
JRI2
JRI1
Page 21
Quick Reference Guide
ERS-CDVE Quick Reference Guide
21
2.5.3 LPC port connector (LPC1)
Signal
PIN
PIN
Signal
LPC_AD0
1 2 +3V
LPC_AD1
3 4 PLTRST#
LPC_AD2
5 6 LPC_LFRAME#
LPC_AD3
7 8 LPC1_PCI_CLK
SERIRQ
9
10
GND
+5V
11
12
GND
+5V
13
14
LPC_LDRQ1#
2.5.4 Power connector (PWR1)
Signal
PIN
+5V 1 GND
2
GND
3
+12V
4
Page 22
ERS-CDVE
22 ERS-CDVE Quick Reference Guide
2.5.5 LCD inverter connector (BKL1)
Signal
PIN
+12V
1
GND
2
LVDS_BKLTEN
3
BRIGHT
4
+5V
5
2.5.6 LCD backlight brightness adjustment (JVR)
Signal
PIN
+5V
1
BRIGHT
2
GND
3
Variation Resistor
(Recommended: 4.7KΩ, >1/16W)
Page 23
Quick Reference Guide
ERS-CDVE Quick Reference Guide
23
2.5.7 SPI connector (SPI1)
Signal
PIN
PIN
Signal
+3V
1 2 GND
SPI_CS#
3 4 SPI_CLK
SPI_SO
5 6 SPI_SI
SPI_HOLD#
7
2.5.8 Front Panel Connector 1 (CN1)
Signal
PIN
PWRBTN#
1
RESET#
2
GND
3
POWER LED+
4
POWER LED-
5
Page 24
ERS-CDVE
24 ERS-CDVE Quick Reference Guide
2.5.9 Front Panel Connector 2 (CN2)
Signal
PIN
SATA_LED+
1
SATA_LED-
2
LAN ACT LED+
3
LAN ACT LED-
4
LAN LINK100+
5
LAN LINK100-
6
LAN LINK1000+
7
LAN LINK1000-
8
2.5.10 DC Output connector (DCOUT_S)
Signal
PIN
DCIN
1
DCIN
2
DCIN
3
GND
4
GND
5
GND
6
Page 25
Quick Reference Guide
ERS-CDVE Quick Reference Guide
25
2.5.11 AT/ATX mode selector (SW1)
*Default
AT/ATX mode
s
AT mode ATX mode*
2.5.11.1 Signal Description –AT/ATX mode selection
AT/ATX mode
Description
AT mode
This Mode supports AT power supply, no need
to press Power button to enable power on/off
ATX mode
This Mode supports ATX power supply. Press the
ATX power button to enable power on/off
Page 26
ERS-CDVE
26 ERS-CDVE Quick Reference Guide
2.6 AUX-M03 Connectors settings
2.6.1 System reset (WCN1)
Signal
PIN
GND
2
WSYSRST#
1
2.6.2 LPT Port (WJPRT1)
Signal
PIN
PIN
Signal
GND
26
25
LPT_SLCT
GND
24
23
LPT_[E
GND
22
21
LPT_BUSY
GND
20
19
LPT_ACK#
GND
18
17
PD7
GND
16
15
PD6
GND
14
13
PD5
GND
12
11
PD4
GND
10 9 PD3
LPT_SLIN#
8 7 PD2
LPT_INIT#
6 5 PD1
LPT_ERR#
4 3 PD0
LPT_AFD#
2 1 STB-
Page 27
Quick Reference Guide
ERS-CDVE Quick Reference Guide
27
2.7 Installing Mounting Brackets (ERS-CDVE)
Step 1. Locate brackets on both sides, matching the holes on the system.
Step 2. Insert and fasten 3 screws on each side of the system to secure Mounting brackets.
Page 28
ERS-CDVE
28 ERS-CDVE Quick Reference Guide
2.8 Installing Hard Disk & Memory, PCI devices (ERS-CDVE)
Step 1. Remove 4 screws to release the HDD bracket.
Step 2.1. Slide HDD into its bracket until properly seated.
Step 2.2. Secure HDD by means of 4 screws.
Step 3. Remove 3 screws on each side of the system to release Mounting brackets and chassis cover.
Step 4. Insert the DDR3 SODIMM into the memory socket and fasten with the screw to complete DDR3 SODIMM
installation.
Step 5. Insert MPCIE cards into designated locations and fasten with 4 screws to complete MPCIE installation.
Loading...