Part No. E2017A290A5R
ARC-1209/1509
12.1"/15" Intel® Atom™ SoC Processor E3845 /Intel®
Celeron® J1900 Fanless Rugged Touch Panel PC with IET
Expansion
Quick Reference Guide
4th Ed – 22 June 2018
Copyright Notice
Copyright 2018 Avalue Technology Inc., ALL RIGHTS RESERVED.
ARC-1209/1509
2 ARC-1209/1509 Quick Reference Guide
FCC Statement
THIS DEVICE COMPLIES WITH PART 15 FCC RULES. OPERATION IS
SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE.
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING
INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS
FOR A CLASS "A" DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES.
THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST
HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A
COMMERCIAL ENVIRONMENT. THIS EQUIPMENT GENERATES, USES, AND CAN
RADIATE RADIO FREQUENCY ENERGY AND, IF NOT INSTATLLED AND USED IN
ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL
INTERFERENCE TO RADIO COMMUNICATIONS.
OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE
HARMFUL INTERFERENCE IN WHICH CASE THE USER WILL BE REQUIRED TO
CORRECT THE INTERFERENCE AT HIS OWN EXPENSE.
A Message to the Customer
Avalue Customer Services
Each and every Avalue’s product is built to the most exacting specifications to ensure
reliable performance in the harsh and demanding conditions typical of industrial
environments. Whether your new Avalue device is destined for the laboratory or the factory
floor, you can be assured that your product will provide the reliability and ease of operation
for which the name Avalue has come to be known.
Your satisfaction is our primary concern. Here is a guide to Avalue’s customer services. To
ensure you get the full benefit of our services, please follow the instructions below carefully.
Technical Support
We want you to get the maximum performance from your products. So if you run into
technical difficulties, we are here to help. For the most frequently asked questions, you can
easily find answers in your product documentation. These answers are normally a lot more
detailed than the ones we can give over the phone. So please consult the user’s manual
first.
To receive the latest version of the user’s manual; please visit our Web site at:
http://www.avalue.com.tw/
Quick Reference Guide
ARC-1209/1509 Quick Reference Guide
3
Content
1. Getting Started ........................................................................................................ 6
1.1 Safety Precautions .................................................................................................... 6
1.2 Packing List ............................................................................................................... 6
1.3 System Specifications ............................................................................................... 7
1.4 System Overview .................................................................................................... 10
1.4.1 I/O View ................................................................................................................................. 10
1.5 System Dimensions ................................................................................................ 11
1.5.1 ARC-1209 (A Model) ............................................................................................................. 11
1.5.2 ARC-1209 (B Model) ............................................................................................................. 12
1.5.3 ARC-1509 (A Model) ............................................................................................................. 13
1.5.4 ARC-1509 (B Model) ............................................................................................................. 14
2. Hardware Configuration ....................................................................................... 15
2.1 ARC-1209/1509 connector mapping ....................................................................... 16
2.1.1 Serial port 1 connector (COM1) ............................................................................................. 16
2.1.2 Serial port 2 connector (COM2) ............................................................................................. 16
2.2 Installing Hard Disk & Memory ................................................................................ 17
2.3 Installing ARC-BYT DB ........................................................................................... 19
2.4 ARC-BYT Overviews ............................................................................................... 21
2.5 ARC-BYT Jumper and Connector list ...................................................................... 22
2.6 ARC-BYT Jumpers & Connectors settings .............................................................. 23
2.6.1 Clear CMOS (JCMOS1) ........................................................................................................ 23
2.6.2 Serial port 1/2 pin9 signal select (JRI1/JRI2) ........................................................................ 23
2.6.3 LCD backlight brightness adjustment (JVR1) ........................................................................ 24
2.6.4 AT/ATX Input power select (JAT1) ........................................................................................ 24
2.6.5 Serial port 1 in RS-422/485 mode (JP1) ............................................................................... 25
2.6.6 LCD Inverter connector (JBKL1) ........................................................................................... 25
2.6.7 On-board header for USB2.0 (H_JUSB3) ............................................................................. 26
2.6.8 SATA Power connector (JSATA2P1) .................................................................................... 26
2.6.9 LVDS connector (JLVDS1) .................................................................................................... 27
2.6.10 Battery connector (BT1) ........................................................................................................ 28
2.6.20 Power connector (PWR1) ...................................................................................................... 33
2.7 ARC-BYT DB-A/B/C/D/E/F/G/H/K Overviews ......................................................... 34
2.7.1 ARC-BYT DB-A ..................................................................................................................... 34
2.7.2 ARC-BYT DB-B ..................................................................................................................... 34
ARC-1209/1509
4 ARC-1209/1509 Quick Reference Guide
2.7.3 ARC-BYT DB-C ..................................................................................................................... 34
2.7.4 ARC-BYT DB-D ..................................................................................................................... 35
2.7.5 ARC-BYT DB-E ..................................................................................................................... 35
2.7.6 ARC-BYT DB-F ...................................................................................................................... 35
2.7.7 ARC-BYT DB-G ..................................................................................................................... 36
2.7.8 ARC-BYT DB-H ..................................................................................................................... 36
2.7.9 ARC-BYT DB-K ..................................................................................................................... 36
2.8 ARC-BYT DB-A/B/C/D/E/F/G/H/K Connector list .................................................... 37
2.8.1 ARC-BYT DB-A ..................................................................................................................... 37
2.8.2 ARC-BYT DB-B ..................................................................................................................... 37
2.8.3 ARC-BYT DB-C ..................................................................................................................... 37
2.8.4 ARC-BYT DB-D ..................................................................................................................... 37
2.8.5 ARC-BYT DB-E ..................................................................................................................... 37
2.8.6 ARC-BYT DB-F ...................................................................................................................... 38
2.8.7 ARC-BYT DB-G ..................................................................................................................... 38
2.8.8 ARC-BYT DB-H ..................................................................................................................... 38
2.8.9 ARC-BYT DB-K ..................................................................................................................... 38
2.9 ARC-BYT DB-D Connectors settings ...................................................................... 40
2.9.1 Serial Port 1 connector (D_COM1)........................................................................................ 40
2.9.2 Serial Port 2 connector (D_COM2)........................................................................................ 40
2.10 ARC-BYT DB-E Jumpers & Connectors settings .................................................... 41
2.10.1 CAN2.0 Switch (E_JCAN20) ................................................................................................. 41
2.10.2 For user update FW (E_JBOOT0) ......................................................................................... 41
2.10.3 For user update FW (E_JIAP1) ............................................................................................. 42
2.11 ARC-BYT DB-F Connectors settings ...................................................................... 44
2.12 ARC-BYT DB-H Jumpers settings ........................................................................... 45
2.12.1 USB Power selector (H_USB_PWR_SEL1) .......................................................................... 45
2.13 ARC-BYT DB-G Connectors settings ...................................................................... 45
2.13.1 Serial Port 1 connector (G_COM1) ....................................................................................... 45
2.13.2 Serial Port 2 connector (G_COM2) ....................................................................................... 46
2.13.3 Serial Port 3 connector (G_COM3) ....................................................................................... 46
2.14 ARC-BYT DB-H Connectors settings ...................................................................... 47
2.14.1 Serial Port 1 connector (H_COM1)........................................................................................ 47
2.14.2 Serial Port 2 connector (H_COM2)........................................................................................ 47
2.15 ARC-BYT DB-K Connectors settings ...................................................................... 48
2.15.1 Serial Port 1 connector (I_COM1) ......................................................................................... 48
2.15.2 Serial Port 2 connector (I_COM2) ......................................................................................... 48
3.BIOS Setup .................................................................................................................... 49
3.1 Introduction ............................................................................................................. 50
3.2 Starting Setup ......................................................................................................... 50
Quick Reference Guide
ARC-1209/1509 Quick Reference Guide
5
3.3 Using Setup ............................................................................................................ 51
3.4 Getting Help ............................................................................................................ 52
3.5 In Case of Problems ................................................................................................ 52
3.6 BIOS setup .............................................................................................................. 53
3.6.1 Advanced Menu ..................................................................................................................... 53
3.6.1.1 IT8528 Super IO Configuration ........................................................................................................ 53
ARC-1209/1509
6 ARC-1209/1509 Quick Reference Guide
1. Getting Started
1.1 Safety Precautions
Warning!
Always completely disconnect the power cord from your
chassis whenever you work with the hardware. Do not
make connections while the power is on. Sensitive
electronic components can be damaged by sudden power
surges. Only experienced electronics personnel should
open the PC chassis.
Caution!
Always ground yourself to remove any static charge before
touching the CPU card. Modern electronic devices are very
sensitive to static electric charges. As a safety precaution,
use a grounding wrist strap at all times. Place all electronic
components in a static-dissipative surface or static-shielded
bag when they are not in the chassis.
1.2 Packing List
1 x ARC-1209/1509 Panel PC
1 x Power Adapter
1 x Power cord
4 x screws for VESA
Quick Reference Guide
ARC-1209/1509 Quick Reference Guide
7
1.3 System Specifications
Panel
ARC-1209
ARC-1509
LCD Size
12.1", 4:3
15", 4:3
Display Type
XGA
Resolution
1024 x 768
Pixel pitch
0.1905 mm (H) x 0.1905 mm (V)
0.297mm(H) x 0.297mm(V)
Luminance
600 cd/m²
400 cd/m²
Contrast ratio
700
Viewing angle
80 (U), 80 (D), 80 (L), 80 (R)
70 (U), 70 (D), 80 (L), 80 (R)
Response time
16ms
Backlight
LED
Touch Type
5 Wires resistive (A Model)
Projected Capacitive (B Model)
Touch Light
Transmission
80% (A Model)
89% (B Model)
Touch Controller
Onboard USB touch (PenMount) (A Model)
EETI (B Model)
System
SBC
ARC-BYT
Processor
Intel® Atom™ E3845 4-Core 1.91GHz ( A Model)
Intel® Celeron® J1900 4-Core 2.0Ghz (B Model)
I/O Chipset
EC ITE IT8528E
System Memory
1 x 204-Pin DDR3L 1333MHz SO-DIMM up to 8 GB
Watchdog Timer
H/W Reset, 1sec. ~ 65535sec./1sec.step
H/W Status Monitor
Monitoring SYSTEM Temperature and Voltage with Auto Throttling Control
Expansion
1 x Mini PCIe Support mSATA
1 x Optional 80-pin Expansion
Storage
1 x 2.5” Drive Bay
I/O
USB
1 x USB 3.0, 3 x USB 2.0
SATA
1 x SATA II
Com Port
1 x RS-232/422/485 (Factory Optional)
1 x RS-232
Other
3 x Knockouts for Antenna Mounting
Display
Chipset
Intel® Valleyview SoC integrated Graphics
Supports optional dual display
Resolution
HDMI: Max. resolution 1920x1200 @ 60Hz (by IET module)
ARC-1209/1509
8 ARC-1209/1509 Quick Reference Guide
Dual Display
HDMI + LVDS
Audio
Audio Codec
Realtek ALC892
Audio Interface
Speaker Out
Speaker Output
2 x 2W
Ethernet
Chipset
2 x Intel® I210IT (A Model)
2 x Intel® I2101AT (B Model)
Ethernet Interface
10/100/1000 Base-Tx GbE compatible
Lan Port
2 x RJ-45
Power Requirement
Power Connector
Lockable DC Jack
Power Requirement
+12V ~ +26V
Power Type
AT/ATX (ATX is default setting)
Adapter
Input: 100 ~ 240Vac/ 50 ~ 60Hz
Output: 60W Adapter (12V @ 5A Adapter)
Mechanical &
Environmental
System Fan
Fanless
Construction - Front
Silver Aluminum
Construction – Rear
Black
Dimension
284 x 223 x 46 mm (A Model)
294 x 226.3 x 51 mm (B Model)
350 x 274 x 49.8 mm (A Model)
350.5 x 274.5 x 53 mm (B Model)
Weight
2.4 Kgs
3.7 Kgs
Operating
Temperature
-20°C ~ 60°C (-4°F ~ 140°F) (A Model)
-10C ~ 50°C (-14°F ~ 122°F) (B Model)
Storage Temperature
-30°C ~ 70°C (-22°F ~ 158°F)
Operating Humidity
0% ~ 90% Relative Humidity, Non-condensing
Vibration Test
ARC-1209 (A Model)
With SSD/mSATA : 5Grms, IEC 60068-2-64, Random, 5 ~ 500Hz, 1hr/axis
ARC-1209 (B Model)/ ARC-1509 (A/B Model)
With SSD/mSATA : 3Grms, IEC 60068-2-64, Random, 5 ~ 500Hz, 1hr/axis
Shock Test
Operating with SSD/CFast/mSATA : MIL-STD-810G, Method 516.6,
Procedure I, functional shock=20G
Certifications
CE, FCC Class B
OS Information
Win 7, Win 8, Win 10, Linux
Ordering Information/
Description
ACC-ARC-USB-1R
4 x USB3.0 (ARC-BYT DB-A)
Quick Reference Guide
ARC-1209/1509 Quick Reference Guide
9
ACC-ARC-AUDIO-1R
HDMI + Audio/Line out, Line in, Mic in (ARC-BYT DB-B)
ACC-ARC-MPCIE-1R
HDMI + Mini PCIe w/ SIM slot (ARC-BYT DB-C)
ACC-ARC-COM-1R
2 x Isolated RS-232 / 2kv (ARC-BYT DB-D)
ACC-ARC-COM-2R
3 x RS-232 (ARC-BYT DB-G)
ACC-ARC-COM-3R
2 x RS-232 + USB 2.0 (ARC-BYT DB-H)
ACC-ARC-COM-4R
2 x RS-232 + LAN (ARC-BYT DB-K)
ACC-ARC-GPIO-1R
12-bit GPIO + 2-pin CAN Bus Kit for ARC Series
ACC-ARC-OBDII-1R
OBDII - CAN Bus Kit for ARC Series (Small Vehicle)
ACC-ARC-OBDII-2R
OBDII - CAN Bus Kit for ARC Series (Large Vehicle)
ACC-ARC-OBDII-3R
OBDII - CAN Bus Kit for ARC Series (Special Large Vehicle)
Note: Specifications are subject to change without notice.
ARC-1209/1509
10 ARC-1209/1509 Quick Reference Guide
1.4 System Overview
1.4.1 I/O View
Connectors
Label
Function
Note
DC-IN
DC Power-in connector
Default: Lockable DC Jack
Option: Phoenix Connector(MOQ apply)
COM1/2
Serial port 1/2 connector
DB-9 male connector
USB
3 x USB 2.0 connector
1 x USB 3.0 connector
LAN1/2
RJ-45 Ethernet 1/2
LED
HDD/Power LED indicator
Power Switch
Power on button
Quick Reference Guide
ARC-1209/1509 Quick Reference Guide
11
1.5 System Dimensions
1.5.1 ARC-1209 (A Model)
(Unit: mm)
ARC-1209/1509
12 ARC-1209/1509 Quick Reference Guide
1.5.2 ARC-1209 (B Model)
(Unit: mm)
Quick Reference Guide
ARC-1209/1509 Quick Reference Guide
13
1.5.3 ARC-1509 (A Model)
(Unit: mm)
ARC-1209/1509
14 ARC-1209/1509 Quick Reference Guide
1.5.4 ARC-1509 (B Model)
(Unit: mm)
Quick Reference Guide
ARC-1209/1509 Quick Reference Guide
15
2. Hardware
Configuration
For advanced information, please refer to:
1- ARC-BYT, ARC-BYT DB-A/B/C/D/E/F/G/H/K included in this manual.
Note: If you need more information, please visit our website:
http://www.avalue.com.tw
ARC-1209/1509
16 ARC-1209/1509 Quick Reference Guide
2.1 ARC-1209/1509 connector mapping
2.1.1 Serial port 1 connector (COM1)
RS-485
Signal
PIN
PIN
Signal
DATA-
1 6 NC
DATA+
2 7 NC
NC
3 8 NC
NC
4 9 NC
GND
5
RS-232
Signal
PIN
PIN
Signal
NDCDA#
1 6 NDSRA#
NRXDA
2 7 NRTSA#
NTXDA
3 8 NCTSA#
NDTRA#
4 9 NRIA#
GND
5
RS-422
Signal
PIN
PIN
Signal
TxD-
1 6 NC
TxD+
2 7 NC
RxD+
3 8 NC
RxD-
4 9 NC
GND
5
2.1.2 Serial port 2 connector (COM2)
Signal
PIN
PIN
Signal
NDCDB#
1 6 NDSRB#
NRXDB
2 7 NRTSB#
NTXDB
3 8 NCTSB#
NDTRB#
4 9 NRIB#
GND
5
Quick Reference Guide
ARC-1209/1509 Quick Reference Guide
17
2.2 Installing Hard Disk & Memory
Step 1. Memory Installation: Remove 3 screws to release the chassis cover, and remove it.
Step 2.1 Insert the SODIMM into the memory socket.
Step 2.2 Re-assemble your system back through previous steps to complete the installation.
ARC-1209/1509
18 ARC-1209/1509 Quick Reference Guide
Step 3. HDD Installation: Insert the HDD into the Drive Bay and fasten 2 screws.
Quick Reference Guide
ARC-1209/1509 Quick Reference Guide
19
2.3 Installing ARC-BYT DB
Step 1. Unfasten 2 screws of the HDD bracket and take it off.
Step 2. Remove 4 screws to release the chassis cover, and remove it.
ARC-1209/1509
20 ARC-1209/1509 Quick Reference Guide
Step 2.1 Insert the ARC-BYT DB into the socket and fasten 3 screws.
Step 2.2 Re-assemble your system back through previous steps to complete the installation
Quick Reference Guide
ARC-1209/1509 Quick Reference Guide
21
2.4 ARC-BYT Overviews
ARC-1209/1509
22 ARC-1209/1509 Quick Reference Guide
2.5 ARC-BYT Jumper and Connector list
Jumper
Label
Function
Note
JCMOS1
Clear CMOS
3 x 1 header, pitch 2.00mm
JRI1/2
Serial port 1/2 pin9 signal select
3 x 2 header, pitch 2.00mm
JP1
Serial port 1 in RS-422/485 mode
4 x 3 header, pitch 2.00mm
JVR1
LCD backlight brightness adjustment
3 x 1 header, pitch 2.00mm
JAT1
AT/ATX Input power select
3 x 1 header, pitch 2.00mm
Connectors
Label
Function
Note
SODIMM1
204-pin DDR3L SODIMM socket
JBKL1
LCD Inverter connector
5 x 1 wafer, pitch 2.00mm
COM1/2
Serial Port 1/2 connector
D-sub 9 pin, male
JTP1
Touch panel connector
5 x 1 header, pitch 2.54mm
JSPR1
AMPLIFIER_R
2 x 1 wafer, pitch 2.00mm
JSPL1
AMPLIFIER_L
2 x 1 wafer, pitch 2.00mm
JB2B1
B2B connector
40 x 2 wafer, pitch 0.80mm
JBLK_CTRL1
LCD backlight brightness adjustment
3 x 2 header, pitch 2.00 mm
LED1
HDD/Power LED indicator
JLVDS1
LVDS connector
DIN 40-pin wafer, pitch 1.25mm
JUSB1/2
USB connector 1/2
LAN1/2
RJ-45 Ethernet 1/2
JPCIE1
PCI Express connector
JFP1
Miscellaneous setting connector
6 x 2 wafer, pitch 2.00 mm
BT1
Battery connector
2 x 1 wafer, pitch 1.25mm
H_JUSB3
On-board header for USB2.0
5 x 2 wafer, pitch 2.00 mm
JLPC1
LPC connector
5 x 2 header, pitch 2.00mm
JPWR1
Power connector
JSPI1
SPI connector
4 x 2 header, pitch 2.00mm
JEC1
EC Debug connector
3 x 1 header, pitch 2.00 mm
JSATA1
Serial ATA connector
JSATA2P1
SATA Power connector
2 x 1 wafer, pitch 2.00mm
JVGA1
VGA connector
8 x 2 wafer, pitch 2.00 mm
Quick Reference Guide
ARC-1209/1509 Quick Reference Guide
23
2.6 ARC-BYT Jumpers & Connectors settings
2.6.1 Clear CMOS (JCMOS1)
*Default
Protect*
Clear CMOS
2.6.2 Serial port 1/2 pin9 signal select (JRI1/JRI2)
* Default
Ring*
+5V
+12V
JRI1
JRI2
ARC-1209/1509
24 ARC-1209/1509 Quick Reference Guide
2.6.3 LCD backlight brightness adjustment (JVR1)
* Default
PWM Mode*
DC Mode
2.6.4 AT/ATX Input power select (JAT1)
* Default
ATX*
AT
Quick Reference Guide
ARC-1209/1509 Quick Reference Guide
25
2.6.5 Serial port 1 in RS-422/485 mode (JP1)
* Default
For RS-232* For RS-422/485
PIN
Signal
PIN
Signal
PIN
Signal
1
NDCDA#
2
COM1-1
3
485_422TX1-
4
NRXDA
5
COM1-2
6
485_422TX1+
7
NTXDA
8
COM1-3
9
422RX1+
10
NDTRA#
11
COM1-4
12
422RX1-
2.6.6 LCD Inverter connector (JBKL1)
Signal
PIN
+12V
1
GND
2
BKLEN
3
VBRIGHT
4
+5V
5
Note:
For inverters with adjustable Backlight function, it is possible to control the LCD brightness through
the VR signal controlled by JVR. Please see the JVR section for detailed circuitry information.
ARC-1209/1509
26 ARC-1209/1509 Quick Reference Guide
2.6.7 On-board header for USB2.0 (H_JUSB3)
Signal
PIN
USBVCC4
1
USB_DN_R_5
2
USB_DP_R_5
3
GND
4
GND
5
2.6.8 SATA Power connector (JSATA2P1)
Signal
PIN
GND
1
+5V
2
Quick Reference Guide
ARC-1209/1509 Quick Reference Guide
27
2.6.9 LVDS connector (JLVDS1)
Signal
PIN
PIN
Signal
+12V
39
40
+12V
GND
37
38
GND
LVDS_CLK2_N
35
36
LVDS_CLK1_N
LVDS_CLK2_P
33
34
LVDS_CLK1_P
GND
31
32
GND
LVDS_DATA7_N
29
30
LVDS_DATA6_N
LVDS_DATA7_P
27
28
LVDS_DATA6_P
GND
25
26
GND
LVDS_DATA5_N
23
24
LVDS_DATA4_N
LVDS_DATA5_P
21
22
LVDS_DATA4_P
GND
19
20
GND
LVDS_DATA3_N
17
18
LVDS_DATA2_N
LVDS_DATA3_P
15
16
LVDS_DATA2_P
GND
13
14
GND
LVDS_DATA1_N
11
12
LVDS_DATA0_N
LVDS_DATA1_P
9
10
LVDS_DATA0_P
GND
7 8 GND
NC
5 6 NC
+3.3V
3 4 +5V
+3.3V
1 2 +5V
ARC-1209/1509
28 ARC-1209/1509 Quick Reference Guide
2.6.10 Battery connector (BT1)
Signal
PIN
+3.3VSB
1
GND
2
2.6.11 AMPLIFIER_R (JSPR1)
Signal
PIN
SPK_R+
1
SPK_R-
2
Quick Reference Guide
ARC-1209/1509 Quick Reference Guide
29
2.6.12 AMPLIFIER_L (JSPL1)
Signal
PIN
SPK_L+
1
SPK_L-
2
2.6.13 LPC connector (JLPC1)
Signal
PIN
PIN
Signal
GND
10 9 LPC_SERIRQ
LPC_PORT80_CLK
8 7 LPC_AD3
LPC_FRAME#
6 5 LPC_AD2
LPC_PORT80_RST#
4 3 LPC_AD1
+3.3V
2 1 LPC_AD0
ARC-1209/1509
30 ARC-1209/1509 Quick Reference Guide
2.6.14 SPI connector (JSPI1)
Signal
PIN
PIN
Signal
+VSPI_BIOS
1 2 GND
SPI_ROM_CS#
3 4 SPI_ROM_CLK
SPI_ROM_MISO_R
5 6 SPI_ROM_MOSI
SPI_HOLD#
7
2.6.15 EC_Program (JEC1)
Signal
PIN
EC_SMCLK_DEBUG
1
EC_SMDAT_DEBUG
2
GND
3
Quick Reference Guide
ARC-1209/1509 Quick Reference Guide
31
2.6.16 Miscellaneous setting connector (JFP1)
Signal
PIN
PWBT
1
2
RST#
3
4
PWR-LED-
5
PWR-LED+
6
HDD-LED-
7
HDD-LED+
8
LAN1-LED-
9
LAN1-LED+
10
LAN2-LED-
11
LAN2-LED+
12
2.6.17 LCD backlight brightness adjustment (JBLK_CTRL1)
PIN
Signal
Note
1-2
BLK_VR_MOD
VR must select 10K/1%
3-4
BLK_BRI_UP
Low pulse button for
backlight brighter
5-6
BLK_BRI_DN
Low pulse button for
backlight dim
ARC-1209/1509
32 ARC-1209/1509 Quick Reference Guide
2.6.18 B2B connector (JB2B1)
Signal
PIN
PIN
Signal
GND
1
41
GND
GND
2
42
GND
+12VSB
3
43
GND
+12VSB
4
44
GND
GND
5
45
GND
LPC_SERIRQ
6
46
+5VSB
LPC_FRAME#
7
47
+5VSB
LPC_COM_CLK1
8
48
+5VSB
LPC_AD0
9
49
+5VSB
LPC_AD1
10
50
+5VSB
Signal
PIN
PIN
Signal
LPC_AD2
11
51
GND
LPC_AD3
12
52
USB_DP4
PS_ON
13
53
USB_DN4
PLT_RST#
14
54
GND
SLP_S3#
15
55
SMB_CLK
HDMI_HPD
16
56
SMB_DATA
GND
17
57
GND
HDMI_SCLK_R
18
58
DIS_MPCIE
HDMI_SDATA_R
19
59
PONRSTB
GND
20
60
USB3-0_SMIB
DDI0_HDMI_TXN_2
21
61
PCIE_WAKE#_3
DDI0_HDMI_TXP_2
22
62
PEIE_RESET#_3
GND
23
63
PCIE_CLKREQ#_3
DDI0_HDMI_TXN_1
24
64
GND
DDI0_HDMI_TXP_1
25
65
PCIE_TXN_3
GND
26
66
PCIE_TXP_3
DDI0_HDMI_TXN_0
27
67
GND
DDI0_HDMI_TXP_0
28
68
PCIE_RXN_3
GND
29
69
PCIE_RXP_3
DDI0_HDMI_CLK_N
30
70
GND
DDI0_HDMI_CLK_P
31
71
PCIE_CLKN_3
GND
32
72
PCIE_CLKP_3
GND
33
73
GND
MIC_RIN
34
74
GND
MIC_LIN
35
75
MIC1_JD
GND
36
76
GND
LINEOUT1_JD
37
77
LINE1_JD
LINEOUT_R
38
78
LINE1_RIN
LINEOUT_L
39
79
LNE1_LIN
GND
40
80
GND
Quick Reference Guide
ARC-1209/1509 Quick Reference Guide
33
2.6.19 Touch panel connector (JTP1)
Signal
PIN
UL
1
UR
2
PROBE
3
LL
4
LR
5
2.6.20 Power connector (PWR1)
*Option: Phoenix Connector
Signal
PIN
+DCIN
1
GND
2
ARC-1209/1509
34 ARC-1209/1509 Quick Reference Guide
2.7 ARC-BYT DB-A/B/C/D/E/F/G/H/K Overviews
2.7.1 ARC-BYT DB-A
2.7.2 ARC-BYT DB-B
2.7.3 ARC-BYT DB-C
Quick Reference Guide
ARC-1209/1509 Quick Reference Guide
35
2.7.4 ARC-BYT DB-D
2.7.5 ARC-BYT DB-E
2.7.6 ARC-BYT DB-F
ARC-1209/1509
36 ARC-1209/1509 Quick Reference Guide
2.7.7 ARC-BYT DB-G
2.7.8 ARC-BYT DB-H
2.7.9 ARC-BYT DB-K
Quick Reference Guide
ARC-1209/1509 Quick Reference Guide
37
2.8 ARC-BYT DB-A/B/C/D/E/F/G/H/K Connector list
2.8.1 ARC-BYT DB-A
Connectors
Label
Function
Note
A_JUSB1~4
USB3.0 connector 1~4
A_JB2B1
B2B connector
2.8.2 ARC-BYT DB-B
Connectors
Label
Function
Note
B_LINE_OUT1
Line-out audio jack
B_LINE_IN1
Line-in audio jack
B_MIC_IN1
Mic-in audio jack
B_JHDMI1
HDMI connector
B_JB2B1
B2B connector
2.8.3 ARC-BYT DB-C
Connectors
Label
Function
Note
C_JPCIE1
Mini PCI Express connector
C_JSIM1
SIM card slot (Push-push)
C_JHDMI1
HDMI connector
C_JB2B1
B2B connector
2.8.4 ARC-BYT DB-D
Connectors
Label
Function
Note
D_COM1/2
Serial Port 1/2 connector
DB-9 male connector
D_JB2B1
B2B connector
2.8.5 ARC-BYT DB-E
Jumpers
Label
Function
Note
E_JCAN20
CAN2.0 Switch
3 x 1 header, pitch 2.00mm
E_JIAP1
For user update FW
3 x 1 header, pitch 2.00mm
ARC-1209/1509
38 ARC-1209/1509 Quick Reference Guide
E_JBOOT0
For user update FW
3 x 1 header, pitch 2.00mm
Connectors
Label
Function
Note
E_GPIO1
General purpose I/O connector
14 x 1 terminal, pitch 2.50mm
E_CN1
For user update FW
5 x 1 header, pitch 2.54mm
E_CAN1
CAN Bus connector
3 x 1 terminal, pitch 2.50mm
E_JB2B1
B2B connector
2.8.6 ARC-BYT DB-F
Connectors
Label
Function
Note
F_CAN1
CAN Bus connector 1
7 x 2 header, pitch 2.00mm
F_CAN2
CAN Bus connector 2
F_JB2B1
B2B connector
2.8.7 ARC-BYT DB-G
Connectors
Label
Function
Note
G_COM1/2/3
Serial Port 1/2/3 connector
DB-9 male connector
G_JB2B1
B2B connector
2.8.8 ARC-BYT DB-H
Jumpers
Label
Function
Note
H_USB_PWR_SEL1
USB Power selector
3 x 1 header, pitch 2.00mm
Connectors
Label
Function
Note
H_JUSB1
USB3.0 connector
H_COM1/2
Serial Port 1/2 connector
DB-9 male connector
H_JB2B1
B2B connector
2.8.9 ARC-BYT DB-K
Connectors
Label
Function
Note
Quick Reference Guide
ARC-1209/1509 Quick Reference Guide
39
I_JLAN1
RJ-45 Ethernet
I_COM1/2
Serial Port 1/2 connector
DB-9 male connector
I_JB2B1
B2B connector
ARC-1209/1509
40 ARC-1209/1509 Quick Reference Guide
2.9 ARC-BYT DB-D Connectors settings
2.9.1 Serial Port 1 connector (D_COM1)
Signal
PIN
PIN
Signal
NDCD#_3_D
1 6 NDSR#_3_D
NRXD_3_D
2 7 NRTS#_3_D
NTXD_3_D
3 8 NCTS#_3_D
NDTR#_3_D
4 9 NRI#_3_D
GND
5
2.9.2 Serial Port 2 connector (D_COM2)
Signal
PIN
PIN
Signal
NDCD#_2_D
1 6 NDSR#_2_D
NRXD_2_D
2 7 NRTS#_2_D
NTXD_2_D
3 8 NCTS#_2_D
NDTR#_2_D
4 9 NRI#_2_D
GND
5
Quick Reference Guide
ARC-1209/1509 Quick Reference Guide
41
2.10 ARC-BYT DB-E Jumpers & Connectors settings
2.10.1 CAN2.0 Switch (E_JCAN20)
*Default
CAN2.0A (11-bit)*
CAN2.0B (29-bit)
2.10.2 For user update FW (E_JBOOT0)
*Default
Default*
For user update FW
ARC-1209/1509
42 ARC-1209/1509 Quick Reference Guide
2.10.3 For user update FW (E_JIAP1)
*Default
Default*
For user update FW
2.10.4 For user update FW (E_CN1)
Signal
PIN
+3.3V
1
SWDIO
2
SWCLK
3
CAN_BUS_RESET#
4
GND
5
Quick Reference Guide
ARC-1209/1509 Quick Reference Guide
43
2.10.5 General purpose I/O connector (E_GPIO1)
Signal
PIN
GND
14
+3.3V
13
DO5
12
DO4
11
DO3
10
DO2
9
DO1
8
DO0
7
DI5 6 DI4 5 DI3 4 DI2 3 DI1 2 DI0
1
2.10.6 CAN Bus connector (E_CAN1)
Signal
PIN
CANH
1
CANL
2
GND
3
ARC-1209/1509
44 ARC-1209/1509 Quick Reference Guide
2.11 ARC-BYT DB-F Connectors settings
2.11.1 CAN Bus connector 1 (F_CAN1)
Signal
PIN
PIN
Signal
CAN_PWR
1 2 CAN_8
CAN_IND
3 4 CAN_9
GND
5 6 BAT_GND
CAN_WAKE
7 8 CAN_11
UART_RXD_1_F
9
10
CAN_12
UART_TXD_1_F
11
12
CAN_13
+5V
13
14
CAN_14
2.11.2 CAN Bus connector 2 (F_CAN2)
Signal
PIN
PIN
Signal
BAT_PWR
1 6 CAN_12
CAN_8
2 7 CAN_13
CAN_9
3 8 CAN_14
BAT_GND
4 9 NC
CAN_11
5
Quick Reference Guide
ARC-1209/1509 Quick Reference Guide
45
2.12 ARC-BYT DB-H Jumpers settings
2.12.1 USB Power selector (H_USB_PWR_SEL1)
*Default
+5VSB*
+5V
2.13 ARC-BYT DB-G Connectors settings
2.13.1 Serial Port 1 connector (G_COM1)
Signal
PIN
PIN
Signal
NDCD#_3_G
1 6 NDSR#_3_G
NRXD_3_G
2 7 NRTS#_3_G
NTXD_3_G
3 8 NCTS#_3_G
NDTR#_3_G
4 9 NRI#_3_G
GND
5
ARC-1209/1509
46 ARC-1209/1509 Quick Reference Guide
2.13.2 Serial Port 2 connector (G_COM2)
Signal
PIN
PIN
Signal
NDCD#_2_G
1 6 NDSR#_2_G
NRXD_2_G
2 7 NRTS#_2_G
NTXD_2_G
3 8 NCTS#_2_G
NDTR#_2_G
4 9 NRI#_2_G
GND
5
2.13.3 Serial Port 3 connector (G_COM3)
Signal
PIN
PIN
Signal
NDCD#_1_G
1 6 NDSR#_1_G
NRXD_1_G
2 7 NRTS#_1_G
NTXD_1_G
3 8 NCTS#_1_G
NDTR#_1_G
4 9 NRI#_1_G
GND
5
Quick Reference Guide
ARC-1209/1509 Quick Reference Guide
47
2.14 ARC-BYT DB-H Connectors settings
2.14.1 Serial Port 1 connector (H_COM1)
Signal
PIN
PIN
Signal
NDCD#_1_H
1 6 NDSR#_1_H
NRXD_1_H
2 7 NRTS#_1_H
NTXD_1_H
3 8 NCTS#_1_H
NDTR#_1_H
4 9 NRI#_1_H
GND
5
2.14.2 Serial Port 2 connector (H_COM2)
Signal
PIN
PIN
Signal
NDCD#_2_H
1 6 NDSR#_2_H
NRXD_2_H
2 7 NRTS#_2_H
NTXD_2_H
3 8 NCTS#_2_H
NDTR#_2_H
4 9 NRI#_2_H
GND
5
ARC-1209/1509
48 ARC-1209/1509 Quick Reference Guide
2.15 ARC-BYT DB-K Connectors settings
2.15.1 Serial Port 1 connector (I_COM1)
Signal
PIN
PIN
Signal
NDCD#_1_I
1 6 NDSR#_1_I
NRXD_1_I
2 7 NRTS#_1_I
NTXD_1_I
3 8 NCTS#_1_I
NDTR#_1_I
4 9 NRI#_1_I
GND
5
2.15.2 Serial Port 2 connector (I_COM2)
Signal
PIN
PIN
Signal
NDCD#_2_I
1 6 NDSR#_2_I
NRXD_2_I
2 7 NRTS#_2_I
NTXD_2_I
3 8 NCTS#_2_I
NDTR#_2_I
4 9 NRI#_2_I
GND
5
Quick Reference Guide
ARC-1209/1509 Quick Reference Guide
49
3.BIOS Setup
ARC-1209/1509
50 ARC-1209/1509 Quick Reference Guide
3.1 Introduction
The BIOS setup program allows users to modify the basic system configuration. In this
following chapter will describe how to access the BIOS setup program and the
configuration options that may be changed.
3.2 Starting Setup
The AMI BIOS™ is immediately activated when you first power on the computer. The BIOS
reads the system information contained in the NVRAM and begins the process of checking
out the system and configuring it. When it finishes, the BIOS will seek an operating system
on one of the disks and then launch and turn control over to the operating system.
While the BIOS is in control, the Setup program can be activated in one of two ways:
By pressing <Del> or <F2> immediately after switching the system on, or
By pressing the <Del> or <F2> key when the following message appears briefly at the
left-top of the screen during the POST (Power On Self Test).
Press <Del> or <F2> to enter SETUP
If the message disappears before you respond and you still wish to enter Setup, restart the
system to try again by turning it OFF then ON or pressing the "RESET" button on the
system case. You may also restart by simultaneously pressing <Ctrl>, <Alt>, and <Delete>
keys. If you do not press the keys at the correct time and the system does not boot, an error
message will be displayed and you will again be asked to.
Press F1 to Continue, DEL to enter SETUP
Quick Reference Guide
ARC-1209/1509 Quick Reference Guide
51
3.3 Using Setup
In general, you use the arrow keys to highlight items, press <Enter> to select, use the
PageUp and PageDown keys to change entries, press <F1> for help and press <Esc> to
quit. The following table provides more detail about how to navigate in the Setup program
using the keyboard.
Button
Description
↑
Move to previous item
↓
Move to next item
←
Move to the item in the left hand
→
Move to the item in the right hand
Esc key
Main Menu -- Quit and not save changes into NVRAM
Status Page Setup Menu and Option Page Setup Menu -- Exit current page and
return to Main Menu
+ key
Increase the numeric value or make changes
- key
Decrease the numeric value or make changes
F1 key
General help, only for Status Page Setup Menu and Option Page Setup Menu
F2 key
Previous Values.
F3 key
Optimized defaults
F4 key
Save & Exit Setup
Navigating Through The Menu Bar
Use the left and right arrow keys to choose the menu you want to be in.
Note: Some of the navigation keys differ from one screen to another.
To Display a Sub Menu
Use the arrow keys to move the cursor to the sub menu you want. Then press
<Enter>. A “” pointer marks all sub menus.
ARC-1209/1509
52 ARC-1209/1509 Quick Reference Guide
3.4 Getting Help
Press F1 to pop up a small help window that describes the appropriate keys to use and the
possible selections for the highlighted item. To exit the Help Window press <Esc> or the F1
key again.
3.5 In Case of Problems
If, after making and saving system changes with Setup, you discover that your computer no
longer is able to boot, the AMI BIOS supports an override to the NVRAM settings which
resets your system to its defaults.
The best advice is to only alter settings which you thoroughly understand. To this end, we
strongly recommend that you avoid making any changes to the chipset defaults. These
defaults have been carefully chosen by both BIOS Vendor and your systems manufacturer
to provide the absolute maximum performance and reliability. Even a seemingly small
change to the chipset setup has the potential for causing you to use the override.
Quick Reference Guide
ARC-1209/1509 Quick Reference Guide
53
3.6 BIOS setup
Once you enter the Aptio Setup Utility, the Main Menu will appear on the screen. The Main
Menu allows you to select from several setup functions and exit choices. Use the arrow
keys to select among the items and press <Enter> to accept and enter the sub-menu.
3.6.1 Advanced Menu
This section allows you to configure your CPU and other system devices for basic operation
through the following sub-menus.
3.6.1.1 IT8528 Super IO Configuration
When new DB board is connected, item value should be adjusted manually.
Item
Option
Description
DB board
DB-A/C/E/J
DB-B
DB-F 1COM
DB-D/H/K 2COM
DB-G 3COM
M/B mode test[Default]
DB board A-K. DB-A/B/C/D/E/J w/o
UART DB-G w/t 3UART DB-D/H/K w/t
2UART DB-F w/t 1UART.
Loading...