Avalue EMX-NM70 User Manual
EMX-NM70
Intel® Celeron® Processor Mini ITX
Motherboard with Intel® NM70 Express Chipset
User’s Manual
1st Ed – 18 July 2013
Part No. E2047NM7000R
EMX-NM70 User’s Manual
FCC Statement
Copyright Notice
Disclaimer
THIS DEVICE COMPLIES WITH PART 15 FCC RULES. OPERATION IS
SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE.
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING
INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS
FOR A CLASS "A" DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES.
THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST
HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A
COMMERCIAL ENVIRONMENT. THIS EQUIPMENT GENERATES, USES, AND CAN
RADIATE RADIO FREQUENCY ENERGY AND, IF NOT INSTALLED AND USED IN
ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL
INTERFERENCE TO RADIO COMMUNICATIONS.
OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE
HARMFUL INTERFERENCE IN WHICH CASE THE USER WILL BE REQUIRED TO
CORRECT THE INTERFERENCE AT HIS OWN EXPENSE.
Copyright 2013 Avalue Technology Inc., ALL RIGHTS RESERVED.
No part of this document may be reproduced, copied, translated, or transmitted in any form
or by any means, electronic or mechanical, for any purpose, without the prior written
permission of the original manufacturer.
Avalue Technology Inc. reserves the right to make changes, without notice, to any product,
including circuits and/or software described or contained in this manual in order to improve
design and/or performance. Avalue Technology assumes no responsibility or liability for the
use of the described product(s), conveys no license or title under any patent, copyright, or
masks work rights to these products, and makes no representations or warranties that
these products are free from patent, copyright, or mask work right infringement, unless
otherwise specified. Applications that are described in this manual are for illustration
purposes only. Avalue Technology Inc. makes no representation or warranty that such
application will be suitable for the specified use without further testing or modification.
2 EMX-NM70 User’s Manual
EMX-NM70 User’s Manual
Content
1. Getting Started ............................................................................................................ 5
1.1 Safety Precautions .......................................................................................... 5
1.2 Packing List .................................................................................................... 5
1.3 Document Amendment History ....................................................................... 6
1.4 Manual Objectives .......................................................................................... 7
1.5 Specifications ................................................................................................. 8
1.6 Architecture Overview—Block Diagram........................................................ 10
2. Hardware Configuration ........................................................................................... 12
2.1 Product Overview ......................................................................................... 13
2.2 Installation Procedure ................................................................................... 14
2.3 Jumper and Connector List .......................................................................... 15
2.4 Setting Jumpers & Connectors ..................................................................... 17
2.4.1 mSATA/Mini PCIe function Jumper (JS1/JS2) ...................................... 17
2.4.2 Jumper for LVDS power (PWR_LVDS) ................................................. 17
2.4.3 Jumper for inverter power (ADJ_PWR) ................................................. 18
2.4.4 Serial port 1/2 connector (JCOM1/2) ..................................................... 18
2.4.5 Front Panel Switches (FPANEL) ........................................................... 19
2.4.6 LCD Inverter connector (INCN1) ........................................................... 19
2.4.7 LVDS connector (JLVDS1) .................................................................... 20
2.4.8 General Purpose I/O (GPIO1) ............................................................... 21
2.4.9 USB Connector 1 - USB2.0 (FUSB1) ................................ .................... 21
2.4.10 CIR connector (CIR) ............................................................................. 22
2.4.11 Speaker Headers (JSPK) ..................................................................... 22
2.4.12 Power connector (J1) ........................................................................... 23
2.4.13 SATA Power connector 1/2 (VSATA1/2) ................................ .............. 24
3.BIOS Setup .................................................................................................................... 25
3.1 Introduction ................................................................................................... 26
3.2 Starting Setup ............................................................................................... 26
3.3 Using Setup .................................................................................................. 27
3.4 Getting Help ................................................................................................. 28
3.5 In Case of Problems ..................................................................................... 28
3.6 BIOS setup ................................................................................................... 29
3.6.1 Main Menu ............................................................................................ 29
3.6.1.1 System Language .......................................................................... 29
3.6.1.2 System Date .................................................................................. 29
EMX-NM70 User’s Manual 3
EMX-NM70 User’s Manual
3.6.1.3 System Time .................................................................................. 29
3.6.2 Advanced BIOS settings ....................................................................... 30
3.6.2.1 CPU Configuration ......................................................................... 30
3.6.2.2 Onboard Device Configuration ....................................................... 31
3.6.2.3 USB Legacy Features .................................................................... 32
3.6.2.4 Inter® Rapid Start Technology ....................................................... 33
3.6.2.5 Advanced Power Management ...................................................... 33
3.6.2.6 Super IO Configuration .................................................................. 34
3.6.2.6.1 Serial Port 1 Configuration ................................................. 35
3.6.2.6.2 Serial Port 2 Configuration ................................................. 35
3.6.2.7 HW Monitor .................................................................................... 36
3.6.2.8 Watchdog Configuration ................................................................ 37
3.6.2.9 Serial Port Console Redirection ................................ ..................... 38
3.6.3 Chipset ..................................................................................................... 39
3.6.3.1 SB Configuration ............................................................................ 39
3.6.3.2 NB Configuration............................................................................ 40
3.6.3.2.1 LCD Control ......................................................................... 41
3.6.3.3 NB Configuration-GPU ................................................................... 42
3.6.3.3.1 LCD Control-GPU ................................................................ 43
3.6.4 Boot settings ......................................................................................... 44
3.6.5 Security ................................................................................................. 45
3.6.5.1 Administrator Password ................................................................. 45
3.6.5.2 User Password............................................................................... 45
3.6.6 Save & Exit ............................................................................................ 46
3.6.6.1 Save Changes and Reset .............................................................. 46
3.6.6.2 Discard Changes and Reset .......................................................... 46
3.7 The setup step of setting Triple display on EMX-NM70-GPU ....................... 47
4. Drivers Installation....................................................................................................... 49
4.1 Install Chipset Driver .................................................................................... 50
4.2 Install VGA Driver ......................................................................................... 51
4.3 Install LAN Driver (For Realtek 8111E Gigabit Ethernet) ............................. 53
4.4 Install ME Driver ........................................................................................... 54
4.5 Install Audio Driver (For Realtek ALC661 HD Audio) ................................... 55
4.6 Install CIR Driver ................................ ................................ .......................... 56
4.7 Install VGA Driver for EMX-NM70-GPU Board only ..................................... 57
5. Mechanical Drawing .................................................................................................... 58
4 EMX-NM70 User’s Manual
EMX-NM70 User’s Manual
1. Getting Started
1.1 Safety Precautions
Warning!
Always completely disconnect the power cord from your
chassis whenever you work with the hardware. Do not
make connections while the power is on. Sensitive
electronic components can be damaged by sudden power
surges. Only experienced electronics personnel should
open the PC chassis.
Caution!
Always ground yourself to remove any static charge before
touching the CPU card. Modern electronic devices are very
sensitive to static electric charges. As a safety precaution,
use a grounding wrist strap at all times. Place all electronic
components in a static-dissipative surface or static-shielded
bag when they are not in the chassis.
Always note that improper disassembling action could cause damage to the
motherboard. We suggest not removing the heatsink without correct
instructions in any circumstance. If you really have to do this, please contact
us for further support.
1.2 Packing List
Before you begin installing your single board, please make sure that the
following materials have been shipped:
Quick Installation Guide X 1
Driver/Utility CD X 1
Serial ATA Signal Cable X 1
Serial ATA Power Cable X 1
IO Shield
COM Cable X 1
Screw X 3
Motherboard X 1
EMX-NM70 User’s Manual 5
EMX-NM70 User’s Manual
Revision
Date
By
Comment
1st
July 2013
Avalue
Initial Release
1.3 Document Amendment History
6 EMX-NM70 User’s Manual
EMX-NM70 User’s Manual
1.4 Manual Objectives
This manual describes in details Avalue Technology EMX-NM70 Single Board.
We have tried to include as much information as possible but we have not duplicated
information that is provided in the standard IBM Technical References, unless it proved to
be necessary to aid in the understanding of this board.
We strongly recommend that you study this manual carefully before attempting to set up
EMX-NM70 series or change the standard configurations. Whilst all the necessary
information is available in this manual we would recommend that unless you are confident,
you contact your supplier for guidance.
If you have any suggestions or find any errors regarding this manual and want to inform us
of these, please contact our Customer Service department with the relevant details.
EMX-NM70 User’s Manual 7
EMX-NM70 User’s Manual
System
CPU
Intel® Celeron® Processor 1037U (2M Cache,1.80 GHz) upgradable with
Celeron level Processor
BIOS
AMI uEFI BIOS, 64Mbit SPI Flash ROM
System Chipset
Intel® NM70 Express Chipset
I/O Chip
nuvoTon NCT6106D
System Memory
1 x 204-pin DDR3 1333 SODIMMs, up to 8GB
Watchdog Timer
H/W Reset, 1sec. – 65535sec./min.
1sec. or 1min. step
H/W Status
Monitor
CPU & system temperature monitoring
Voltages monitoring
Buzzer
Buzzer onboard
Expansion
1 x Mini PCI-e (Mini PCI-e and mSATA SSD is Switchable Through Jumper)
I/O
Rear Side External
I/O Connector
1 x RJ-45
2 x dual deck USB 2.0 connectors
1 x VGA
1 x HDMI
1 x Mic-In and 1 x Line-out
1 x DC Jack
Internal I/O
Connector
Storage:
- 1 x SATA III connector
- 1 x SATA II connector
- 2 x SATA power connectors
COM:
- COM1~2: support RS-232 connector, Pin 9 without / +5V&+12V supported
GPIO: 8 bits
1 x Mini PCI-e slot
2 x 5 pin, pitch 2.54mm connector for USB 2.0
2 x 1 x 3 pin, pitch 1.00mm CPU fan connector with smart fan function
supported
1 x horizontal type battery connector
1 x 2 x 5 pin, pitch 2.54mm connector for front panel
1 x 2 x 2 pin ATX power connector for DC 19V input
1 x 2 x 20 pin , pitch 1.00mm connector for LVDS
1 x 5 pin , pitch 2.54mm connector for Inverter
1.5 Specifications
8 EMX-NM70 User’s Manual
EMX-NM70 User’s Manual
1 x 4 pin , pitch 2.54mm connector for speaker
1 x 3 pin , pitch 2.00mm connector for CIR
Display
Chipset
Intel NM70 integrated
Resolution
HDMI:1920x1200
VGA:2048x1536
LVDS
2CH 24bits LVDS 1920x1200
Display chip
Nvidia GF119 Graphics with 512MB memory (optional)
Multi-Display
With GPU : VGA + HDMI + LVDS (By Windows display setting)
Without GPU : VGA + LVDS, HDMI + LVDS
Audio
Chipset
Realtek ALC661 HD Audio Decoding Controller
Audio Interface
Mic-In, Line-In
Audio Amplifier
Realtek ALC105 Stereo Class-D 3W x 2
Ethernet
Chipset
1 x Realtek RTL8111E PCI-Express Gigabit Ethernet
Ethernet Interface
10/100/1000 Gigabit Ethernet
Mechanical &
Environmental
Power
Requirement
DC in +19V
Power Type
Single power +19V Power input / ATX mode
ACPI
Single power ATX Support S0,S1, S3, S4, S5
ACPI 3.0 Compliant
Operating Temp.
0°C ~60°C
Storage Temp.
-40°C ~75°C
Operating
Humidity
0%~90% relative humidity, non-condensing
Size (L x W)
6.7" x 6.7" (170mm x 170mm)
Weight
0.40 kg
EMX-NM70 User’s Manual 9
EMX-NM70 User’s Manual
1.6 Architecture Overview—Block Diagram
The following block diagram shows the architecture and main components of EMX-NM70.
10 EMX-NM70 User’s Manual
EMX-NM70 User’s Manual
The following block diagram shows the architecture and main components of EMX-NM70-GPU.
EMX-NM70 User’s Manual 11
EMX-NM70 User’s Manual
2. Hardware
Configuration
12 EMX-NM70 User’s Manual
EMX-NM70 User’s Manual
2.1 Product Overview
EMX-NM70 User’s Manual 13
EMX-NM70 User’s Manual
2.2 Installation Procedure
This chapter explains you the instructions of how to setup your system.
1. Turn off the power supply.
2. Insert the DIMM module (be careful with the orientation).
3. Insert all external cables for hard disk, floppy, keyboard, mouse, USB etc. except for flat
panel. A CRT monitor must be connected in order to change BIOS settings to support flat
panel.
4. Connect power supply to the board via the AC/DC Adapter.
5. Turn on the power.
6. Enter the BIOS setup by pressing the delete key during boot up. Use the "Save & Exit \
Restore Defaults" feature.
7. If TFT panel display is to be utilized, make sure the panel voltage is correctly set before
connecting the display cable and turning on the power.
14 EMX-NM70 User’s Manual
EMX-NM70 User’s Manual
Jumpers
Label
Function
Note
PWR_LVDS
Jumper for LVDS power
2 x 3 header, pitch 2.54 mm
ADJ_PWR
Jumper for inverter power
3 x 2 header, pitch 2.54 mm
JS1/2
Msata/Mini PCIe function Jumper
3 x 2 header, pitch 2.54 mm
Connectors
Label
Function
Note
F_MIC
Mic-in audio jack
3.5mm phone jack
F_OUT
Line-out audio jack
3.5mm phone jack
USB1/2
USB connector1/2
Stack USB 2.00 connector
LAN
RJ-45 Ethernet connector
RJ45 w/ indicator connector
DCIN
DC power-in connector
2.3 Jumper and Connector List
You can configure your board to match the needs of your application by setting jumpers. A
jumper is the simplest kind of electric switch.
It consists of two metal pins and a small metal clip (often protected by a plastic cover) that
slides over the pins to connect them. To “close” a jumper you connect the pins with the clip.
To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1,
2, and 3. In this case, you would connect either two pins.
The jumper settings are schematically depicted in this manual as follows:
A pair of needle-nose pliers may be helpful when working with jumpers.
Connectors on the board are linked to external devices such as hard disk drives, a
keyboard, or floppy drives. In addition, the board has a number of jumpers that allow you to
configure your system to suit your application.
If you have any doubts about the best hardware configuration for your application, contact
your local distributor or sales representative before you make any changes.
The following tables list the function of each of the board’s jumpers and connectors.
EMX-NM70 User’s Manual 15
EMX-NM70 User’s Manual
CIR
CIR connector
1 x 3 header, pitch 2.00 mm
FPANEL
Front Panel Switches
2 x 5 header, pitch 2.54 mm
JLVDS1
LVDS connector
2 x 20 wafer, pitch 1.00 mm
JSPK
Speaker Headers
1 x 4 wafer, pitch 2.00 mm
HDMI
HDMI connector
INCN1
LCD Inverter connector
5 x 1 header, pitch 2.54 mm
SATA1/2
Serial ATA connector 1/2
SATA 7P connector
VSATA1/2
SATA Power connector 1/2
1 x 4 wafer, pitch 2.50 mm
JCOM1/2
Serial port 1/2 connector
2 x 5 header, pitch 2.00 mm
GPIO
General Purpose I/O
2 x 5 header, pitch 2.54 mm
FUSB1
USB Connector 1 – USB2.0
2 x 5 header, pitch 2.54 mm
VGA
VGA connector
D-SUB 15pin
MPCIE
Mini-PCIe
Half size
DIMM1
DDR3 SODIMM connector1
SO-DIMM 204Pin
J1
Power connector
2 x 2 wafer, pitch 4.20 mm
16 EMX-NM70 User’s Manual
EMX-NM70 User’s Manual
* Default
MINIPCIE*
M-SATA
Pin
Pin
Signal
1-3
2-4
M-SATA
3-5
4-6
MINIPCIE
* Default
Note: This jumper is working for LVDS power.
+3.3V*
+5V
+12V
PIN
Signal
Max current
1-2
+3.3V
1A
3-4
+5V
1A
5-6
+12V
1A
JS1
JS2
2.4 Setting Jumpers & Connectors
2.4.1 mSATA/Mini PCIe function Jumper (JS1/JS2)
2.4.2 Jumper for LVDS power (PWR_LVDS)
EMX-NM70 User’s Manual 17
EMX-NM70 User’s Manual
* Default
Note: This jumper is working for inverter power.
+5V*
+3.3V
GND
PIN
Signal
Max current
1-2
+5V
1A
3-4
+3.3V
1A
5-6
GND
Signal
PIN
PIN
Signal
DCD
1 2 RXD
TXD
3 4 DTR
GND
5 6 DSR
RTS
7 8 CTS
RI 9
Note: Com 1/2 Pin9 without power.
JCOM2
JCOM1
2.4.3 Jumper for inverter power (ADJ_PWR)
2.4.4 Serial port 1/2 connector (JCOM1/2)
18 EMX-NM70 User’s Manual
Loading...