To receive the latest version of the user’s manual; please visit our Web site
at:
http://www.avalue.com.tw
Copyright Notice
Copyright 2011 Avalue Technology Inc., ALL RIGHTS RESERVED.
Part No. E2017371404R
ECM-CX700 Series
Disclaimer
Life Support Policy
A Message to the Customer
Avalue Technology Inc. reserves the right to make changes, without notice, to any product,
including circuits and/or software described or contained in this manual in order to improve
design and/or performance. Avalue Technology assumes no responsibility or liability for the
use of the described product(s), conveys no license or title under any patent, copyright, or
masks work rights to these products, and makes no representations or warranties that
these products are free from patent, copyright, or mask work right infringement, unless
otherwise specified. Applications that are described in this manual are for illustration
purposes only. Avalue Technology Inc. makes no representation or warranty that such
application will be suitable for the specified use without further testing or modification.
Avalue Technology’s PRODUCTS ARE NOT FOR USE AS CRITICAL COMPONENTS IN
LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE PRIOR WRITTEN APPROVAL
OF Avalue Technology Inc.
As used herein:
1. Life support devices or systems are devices or systems which, (a) are intended for
surgical implant into body, or (b) support or sustain life and whose failure to perform,
when properly used in accordance with instructions for use provided in the labeling, can
be reasonably expected to result in significant injury to the user.
2. A critical component is any component of a life support device or system whose failure to
perform can be reasonably expected to cause the failure of the life support device or
system, or to affect its safety or effectiveness.
Avalue Customer Services
Each and every Avalue’s product is built to the most exacting specifications to ensure
reliable performance in the harsh and demanding conditions typical of industrial
environments. Whether your new Avalue device is destined for the laboratory or the factory
floor, you can be assured that your product will provide the reliability and ease of operation
for which the name Avalue has come to be known.
Your satisfaction is our primary concern. Here is a guide to Avalue’s customer services. To
ensure you get the full benefit of our services, please follow the instructions below carefully.
2 ECM-CX700 Series Quick Installation Guide
Quick Installation Guide
3
Headquarters and Branch
Avalue USA
Avalue Technology Inc.
7F, 228, Lian-cheng Road, Chung Ho City, Taipei,
Taiwan
Tel:+886-2-8226-2345
Fax: +886-2-8226-2777
Information:sales@avalue.com.tw
Service: service@avalue.com.tw
Room 805, Building 9,No.99 Tianzhou Rd.,
Caohejing Development Area,
Xuhui District, Shanghai
Tel: +86-21-5169-3609
Fax:+86-21-5445-3266
Information: sales.china@avalue.com.cn
Service: service@avalue.com.tw
Avalue Technology Inc.
2F keduka-Bldg, 2-27-3 Taito,
Taito-Ku, Tokyo 110-0016 Japan
Tel: +81-3-5807-2321
Fax: +81-3-5807-2322
Information: sales.japan@avalue.com.tw
Service: service@avalue.com.tw
Technical Support
We want you to get the maximum performance from your products. So if you run into
technical difficulties, we are here to help. For the most frequently asked questions, you can
easily find answers in your product documentation. These answers are normally a lot more
detailed than the ones we can give over the phone. So please consult the user’s manual
first.
To receive the latest version of the user’s manual; please visit our Web site at:
http://www.avalue.com.tw/
ECM-CX700 Series Quick Installation Guide
ECM-CX700 Series
Contents
1. Getting Started ............................................................................................................ 5
Always completely disconnect the power cord from your
chassis whenever you work with the hardware. Do not
make connections while the power is on. Sensitive
electronic components can be damaged by sudden power
surges. Only experienced electronics personnel should
open the PC chassis.
Always note that improper disassembling action could cause damage to the motherboard.
We suggest not removing the heatsink without correct instructions in any circumstance.
If you really have to do this, please contact us for further support.
Caution!
Always ground yourself to remove any static charge before
touching the CPU card. Modern electronic devices are very
sensitive to static electric charges. As a safety precaution,
use a grounding wrist strap at all times. Place all electronic
components in a static-dissipative surface or static-shielded
bag when they are not in the chassis.
1.2 Packing List
Before you begin installing your single board, please make sure that the
following materials have been shipped:
1 x ECM-CX700 VIA Eden V4 Micro module
1 x Quick Installation Guide for ECM-CX700
1 x DVD-ROM or CD-ROM contains the followings:
— User’s Manual (this manual in PDF file)
— Ethernet driver and utilities
— VGA drivers and utilities
— Audio drivers and utilities
1 x Cable set contains the followings:
— 1 x Daughter board support Audio/2 x USB (P/N:9697000105R)
— 1 x IDE HDD cable (44-pin, pitch 2.0mm)
— 1 x USB cable (10-pin/2.54mm-10pin/2.0mm)
— 1 x Audio cable (12-pin, pitch 2.0mm)
— 1 x Serial ATA cable (7-pin, standard)
— 1 x Serial port cable (10-pin, pitch 2.0mm)
— 1 x PS/2 Keyboard & Mouse Y cable (6-pin, Mini-DIN)
ECM-CX700 Series Quick Installation Guide
ECM-CX700 Series
2. Hardware
Configuration
Note:
For further product information, please visit our
website:
http://www.avalue.com.tw
For further update information, please visit our
technical support site:
http://www.avalue.com.tw/support
For further sales issue, please e-mail us:
sales@avalue.com.tw
6 ECM-CX700 Series Quick Installation Guide
7
2.1 Product Overview
Quick Installation Guide
ECM-CX700 Series Quick Installation Guide
ECM-CX700 Series
Jumpers
Label
Function
Note
JAT1
AT/ATX power select
2 x 1 header, pitch 2.00mm
JSUS1
3 x 1 header, pitch 2.54mm
JCMOS1
Clear CMOS
3 x 1 header, pitch 2.00mm
JVIO1
PCI 104 voltage select
3 x 2 header, pitch 2.54mm
2.2 Jumper and Connector List
You can configure your board to match the needs of your application by setting jumpers. A
jumper is the simplest kind of electric switch.
It consists of two metal pins and a small metal clip (often protected by a plastic cover) that
slides over the pins to connect them. To “close” a jumper you connect the pins with the clip.
To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1,
2, and 3. In this case, you would connect either two pins.
The jumper settings are schematically depicted in this manual as follows:
A pair of needle-nose pliers may be helpful when working with jumpers.
Connectors on the board are linked to external devices such as hard disk drives, a
keyboard, or floppy drives. In addition, the board has a number of jumpers that allow you to
configure your system to suit your application.
If you have any doubts about the best hardware configuration for your application, contact
your local distributor or sales representative before you make any changes.
The following tables list the function of each of the board's jumpers and connectors.
8 ECM-CX700 Series Quick Installation Guide
Quick Installation Guide
9
Connectors
Label
Function
Note
JAUD1
Audio connector
6 x 2 header, pitch 2.0mm
JCD1
CD-ROM audio input connector
4 x 1 wafer, pitch 2.0mm
JCF1
Compact Flash card connector
JCOM1
Serial port 1 connector
5 x 2 header, pitch 2.0mm
JCOM2
Serial port 2 connector
5 x 2 header, pitch 2.0mm
JDIMM1
DDR2 SODIMM 1.8V
200-pin DDR2 SODIMM socket
JDIO1
General purpose I/O connector
5 x 2 header, pitch 2.0mm
JFAN1&2
CPU fan connector
2 x 1 wafer, pitch 2.54mm
JIDE1
Primary IDE connector
22 x 2 header, pitch 2.0mm
JINV1
LCD inverter connector
5 x 1 wafer, pitch 2.0mm
JIR1
IrDA connector
5 x 1 header, pitch 2.54mm
JKB1
PS/2 keyboard & mouse connector
6-pin mini DIN
JLAN1
RJ-45 Ethernet 1
JLAN2
RJ-45 Ethernet 2
JLEDP1
Power Indicator
2 x 1 header, pitch 2.54mm
JLEDH1
HDD Indicator
2 x 1 header, pitch 2.54mm
JLVDS1
LVDS connector
HIROSE DF13-40DP-1.25V
JM1
Lord Port (for Firmware updating only)
5 x 1 header, pitch 2.0mm
JPCI1
PCI-104 connector
5 x 2 header, pitch 2.0mm
JPS1
ATX power switch connector
2 x 1 header, pitch 2.54mm
JPWR1
Power connector
Wafer box 4P 5.08mm
JSATA1
Serial ATA connector 1
Floppy connector
Wafer 7P pitch 1.27mm
JSATA2
Serial ATA connector 2
Wafer 7P pitch 1.27mm
JUSB1
USB connector 0 & 1
5 x 2 header, pitch 2.0mm
JUSB2
USB connector 2 & 3
5 x 2 header, pitch 2.0mm
JVGA1
VGA connector
D-sub 15-pin, Female
JVR1
LCD backlight brightness adjustment
3 x 1 header, pitch 2.54mm
LED1
Power & HDD indicator
S1
Reset button
ECM-CX700 Series Quick Installation Guide
ECM-CX700 Series
JAT1
* Default
AT*
ATX
JSUS1
Signal
PIN
PWR_ON
1
+5V
2
VCCSB
3
Note: The default sets 2-3 closed
for AT power used.
2.3 Setting Jumpers & Connectors
2.3.1 AT/ATX Power Select (JAT1, JSUS1)
10 ECM-CX700 Series Quick Installation Guide
11
* Default
Protect *
Clear CMOS
* Default
+5V*
+3.3V
2.3.2 Clear CMOS (JCMOS1)
Quick Installation Guide
2.3.3 PCI-104 Voltage Select (JVIO1)
ECM-CX700 Series Quick Installation Guide
ECM-CX700 Series
* Default
Signal
PIN
PIN
Signal
LINEOUT_R
1 2 LINEOUT _L
GND
3 4 LFE-OUT
LIN_R
5 6 LIN_L
MIC-IN
7 8 CEN-OUT
SURR-OUT-L
9
10
SURR-OUT-R
SPDIF OUT
11
12
GND
Signal
PIN
CD_L
4
GND
3
CD_R
2
GND
1
2.3.4 Audio connector (JAUD1)
2.3.5 CD-ROM Audio Input Connector (JCD1)
12 ECM-CX700 Series Quick Installation Guide
Quick Installation Guide
13
RS-232 Mode
Signal
PIN
PIN
Signal
GND
10 9 RI
CTS
8 7 RTS
DSR
6 5 GND
DRT
4 3 TxD
RxD
2 1 DCD
RS-422 Mode
Signal
PIN
PIN
Signal
GND
10 9 GND
RxD-
8 7 NC
TxD+
6 5 GND
NC
4 3 NC
RxD+
2 1 TxD-
RS-485 Mode
Signal
PIN
PIN
Signal
GND
10 9 GND
NC
8 7 NC
DATA+
6 5 GND
NC
4 3 NC
NC
2 1 DATA-
2.3.6 Serial Port 2 Connector in RS-232/422/485 Mode (JCOM2)
ECM-CX700 Series Quick Installation Guide
ECM-CX700 Series
Signal
PIN
PIN
Signal
GND
10 9 +5V
GP17
8 7 GP13
GP16
6 5 GP12
GP15
4 3 GP11
GP14
2 1 GP10
Signal
PIN
IRTX
5
GND
4
IRRX
3
NC
2
+5V
1
2.3.7 General Purpose I/O Connector (JDIO1)
2.3.8 IrDA Connector (JIR1)
14 ECM-CX700 Series Quick Installation Guide
15
Signal
PIN
+12V
1
GND
2
ENBKL
3
VR
4
+5V
5
Signal
Signal Description
VR
Vadj = 0.75V ~ 4.25V (Recommended: 4.7KΩ, >1/16W)
ENBKL
LCD backlight ON/OFF control signal
2.3.9 LCD Inverter Connector (JINV1)
Quick Installation Guide
Note:
For inverters with adjustable Backlight function, it is possible to control the
LCD brightness through the VR signal controlled by VR1. Please see the
VR1 section for detailed circuitry information.
2.3.9.1 Signal Description – LCD Inverter Connector (JINV1)