Avalon Firestyles Surround Panels User Manual

Surround Panels (DVS/DVL EF II)

r

e

Compatibility

 DVS Insert EF II
 DVL Insert EF II

Packing List

 Top, Right, and Left Side Panels
 Panel Trim (with Hardware)
 (4) 10-24 Type F Thread-Cutting Screws
 (7) Spring Clips

Part Numbers

 DVS – 4” by 6” 96100300
 DVS – 8” by 10” 96100301
 DVS – 10” by 13” 96100302
 DVL – 4” by 6” 96100320
 DVL – 8” by 10”” 96100321
 DVL – 10” by 13” 96100322

Arched Faces with Screens (2014 or later) Require Use of the Extended Position Holes

This surround panel has 2 sets of holes. Hole position is
determined by the face being used (see below)

Standard Position – used for all faces except for the new
2014 arched faces with screens. All other faces use the
standard position hole. If you are uncertain, use the standa
position.

Extended Position – used only for new arched faces with
screens (2014 or later). The extended position allows room
the screen and eliminates the ½” gap to the panel. The
extended position hole positions the insert ½” farther into th
fireplace cavity.

DVS Side

Panel

DVL Side

Panel

Extended

Position

Standard

Position

Rheostat and On/Off Switch Placement on 33 DVI/31 DVI

Install the rheostat and On/Off switch on the right surround side surround panel (see the Owner’s Manual for details).

Inside Fit Panels

The panels may be cut down in size and placed within the fireplace opening. When installed in this configuration, install the
rheostat and on/off switch in the control panel under the firebox (see the owner’s manual for details). For standard installations, we
recommend you attach the rheostat and on/off switch to the upper right surround panel trim (after the trim is installed).

Installation

Before installation the insert should be in place with the gas line and vent attached. Pull the insert out slightly to assist in the
installation. Attach the side panels then the top panel and trim (see the directions below and on the following page).

DVS / 31 DVI
Side Panel Installation

Pre-thread the holes on the brackets

a

screws included in the surround panel kit.

5/16" Nutdriver

b

Line up each side surround
panel and insert two screws from
the inside to secure in place.

Run the power cord to
the side of the insert.

Page 1 of 2 17601428 - 2/25/14 © Travis Industries, Inc.

Surround Panels (DVS/DVL EF II)

DVL / 33 DVI – Side Panel Installation

b

Line up each side surround
panel and insert two screws from
the inside to secure in place.

Pre-thread the holes on the surround

a

panels with the screws included in the
surround panel kit.

5/16" Nutdriver

Run the power cord to
the side of the insert.

Top Panel and Trim Installation

a

Install the top panel so
the tabs insert into the
joggle clips on the top
panel

Top
Panel

Top Trim

Spring
Clips

"L" Bracket

Slot for on/off
switch and hole for
rheostat
(

31 & 33 DVI Only)

Right Side Trim

Micro (1/16”)
Standard

b

Top Trim

"L" Bracket

Right Side

Trim

Trim Installation:

Insert one leg of each "L" bracket into the top
and side trim piece. Align the trim to form a
precise corner, then tighten the two set
screws with a small standard screwdriver.
Slide the trim over the panels. Place the
spring clips behind the panels at the locations
shown. This keeps the trim tight against the
panel.

Optional Knock-Out

An optional knock-out is provided if the power cord is
routed behind the surround panel.

Screwdriver

Page 2 of 2 17601428 - 2/25/14 © Travis Industries, Inc.