Page 1
Large Pedestal (1750, Olympic)
Compatibility:
• 1750 Wood Stove
• Olympic
Packing List:
• Pedestal
• (2) Dowels
• (2) 3/8-16 x 3/4” Bolts w Washers
• (2) 5/16” x 3” Lag Bolts w Washers
• Screen with (6) Staples
• Cover Plate (for use when using outside air on the Olympic)
• Insulation
Pedestal Attachment
99200129
NOTE: If using outside air, install it prior to attaching the pedestal (see Outside Air Installation on page 2 and 3).
Two pedestal bolts
attach the pedestal to
the bottom of the stove.
9/16" Wrench
Stove
The lag bolts and washers
may be inserted through
these holes to anchor the
pedestal to the floor.
The dowels insert onto
the front and back edge
of the pedestal base.
Page 1 of 4 12/21/07 © Travis Industries, Inc.
Pedestal
Page 2
Large Pedestal (1750, Olympic)
99200129
Using Outside Air with the Olympic Wood Stoves
The following outside air knock-out must be removed and the cover plate installed when using outside air with
the Olympic wood stoves.
Outside Air Knock-Out for
Standard Pedestals
Outside Air Knock-Out for Stoves on Legs
or Stoves Using Ash Pan Pedestal
Rear Blower Knock-Outs
Knock-Out for
the Ash Pan
Pedestal Drop
Chute
FRONT OF STOVE
Install the included cover plate so air is drawn from below, not the front. See the directions below.
Remove the two screws on the
cover plate to remove the piece that
fits over the air control rod. Then
replace the piece when the cover
plate is in place.
The cover plate has a clip which attaches
it underneath the air control.
Air Control Rod
Page 2 of 4 12/21/07 © Travis Industries, Inc.
Page 3
Large Pedestal (1750, Olympic)
AA
AA
AA
AA
99200129
Outside Air Installation – Using the Outside Air Kit (99200139)
a
Tuck insulation (included with the
pedestal) under both sides of the
pedestal and under the holes on the
base of the pedestal. This prevents air
from being
drawn from below
the pedestal.
e
Secure the flex duct to the
air duct assembly using
the included hose clamp.
Attach the outside air duct
assembly to the pedestal
with the same screws that
held the cover plate in
place.
3" Dia. Flex Duct
(4' max. length)
Slide the cover plate over the flex duct
then attach the flex duct to the hood with
the included hose clamp. Secure the
cover plate to the wall with the included
screws (and drywall anchors if needed).
HINT: The flex must be fully stretched and
the ends cut square and flatted for it to fit
properly. The tube on the hood and air
duct may be crimped if necessary.
Remove the cover
b
plate on the pedestal.
Cover Plate
d
Seal the area around
the tube to prevent
air from entering
through the wall.
Silicone
Select a location between
framing members for the
wall penetration.
NOTE: If wall is thicker
than 8", attach the flex duct
to the hood then slide the
hood into place.
Slide the hood
through the wall and
secure to the outside
wall with the two
included screws.
Min. 3"
Silicone
Dia. Hole
8"
Hood with Rodent Screen
c
Page 3 of 4 12/21/07 © Travis Industries, Inc.
Page 4
Large Pedestal (1750, Olympic)
99200129
Outside Air Installation – Through the Pedestal into the Crawl Space
This pedestal has an internal air duct that may be used to direct air to the firebox. Outside air is then drawn from
the crawl space under the stove (check with local building codes for requirements in your area). See the
directions below for installation details.
1 Determine the location of the hole placed under the pedestal. The illustration below details the location of the
pedestal in relation to the front of the stove. The hole should be at least 16 square inches.
Top View
The faceplate of the Olympic is 1/4" in
front of the forward edge of the
pedestal base.
The faceplate of the 1750 is 2-1/2" in
front of the forward edge of the
pedestal base.
26"
16"
17"
19-3/4"
Outside air may be drawn
from this area underneath
the pedestal
(min. 16 square inches)
Pedestal Base
(with dowels)
FRONT
2 Attach the included screen over the hole (staples are included with the pedestal). Tuck insulation under both
sides of the pedestal and under the holes in the base of the pedestal (see step “a” on the page 2). This
prevents air from entering under the pedestal.
Screen is used to prevent
Insulation is used to seal the side
edges of the pedestal .
rodents from entering.
Staples are used to attach
the screen to the floor.
3 Attach the stove to the pedestal.
Page 4 of 4 12/21/07 © Travis Industries, Inc.
Loading...