Avago Technologies LSI SAS 3080X-R User Manual

Quick Installation Guide

CAUTION

32-Bit Slots

64-Bit Slots

(3.3 V)

(3.3 V)

Edge of

Host Board

Bracket

Screw

HDD

Connector

Serial Signal
Cables

HBA to HDD

4-Lane Internal
HBA Connector
SFF-8484

Breakout Cable

Press Here

Press Here

Note:

The HBA shape, size, and locations of
components may vary from this
illustration.

LSISAS3080X-R PCI-X to 3.0 Gbit/s SAS Host Bus Adapter

QUICK HBA INSTALLATION

To install the LSISAS3080X-R, follow these steps:

1. Unpack the HBA and inspect it for damage. Unpack the HBA in a static-free

environment. Remove the HBA from the antistatic bag and inspect it for damage. If it
appears to be damaged, or if any component is missing, contact LSI Logic or your reseller
support representative.

Thank you for purchasing the
LSISAS3080X-R PCI-X to 3.0 Gbit/
s Serial Attached SCSI (SAS) Host
Bus Adapter (HBA). Please take a
few minutes to read this quick
installation guide before you
install the LSISAS3080X-R.

If you need more information
about any topic covered in this
guide, refer to the other
documents on the accompanying
LSI Logic Device Drivers &
Utilities CD.

Contents of the LSI Logic Device
Drivers & Utilities CD

The LSI HBA CD contains utility programs,
device drivers for various operating
systems, and the following LSI
documentation:

• PCI-X to 3.0 G/bit Serial Attached SCSI
(SAS) Host Adapters User’s Guide

• Fusion-MPT™ Device Management
User’s Guide

• LSI HBA technical product briefs

Make a backup of your data before changing your system configuration.

2. Prepare the computer. Turn off the computer and remove the power cord from the

back of the power supply. Remove the cover from the chassis. Be certain to disconnect the
computer from the power supply and from any networks before installing the controller card.

3. Insert the LSISAS3080X-R in an available PCI/PCI-X slot. Locate an empty PCI/PCI-X

slot. Remove the blank bracket panel on the back of the computer that is aligned with the
PCI/PCI-X slot you have selected. Save the bracket screw when present. Align the HBA to
a PCI/PCI-X slot. Press down gently but firmly to properly seat the HBA in the slot. The
following figure illustrates how to insert the HBA in a PCI/PCI-X slot.

NOTE: The LSISAS3080X-R is keyed for a 3.3 V slot. The keying of edge connector J1 prevents the

card from being installed in a 5 V slot.

4. Secure the bracket to the system’s chassis. Install the bracket screw, when present, or

engage the system retention mechanism to secure the HBA to the system’s chassis.

5. Connect the serial cable(s) between the HBA and the serial hard disk drive(s) (HDD).

The LSISAS3080X-R has two internal X4 SAS connectors, each connecting to four 3 Gbit/s
SAS ports. The HBA must be connected to SAS storage devices using the appropriate
cable. For connection to internal drives or backplanes, an internal cable with a standard
SAS Internal Wide Port connector (SFF-8484) on the controller side of the cable is
required. The other end of the cable may fan out into four cables with either SATA-style
signal connectors or SAS device connectors at the end for direct connection to disk drives
(and some backplanes) or single SAS Internal Wide Port connector for backplane
attachment. The following figure illustrates the connector locations on the LSISAS3080X­R and the use of a controller-based, fan-out cable to connect to drives that require a
SATA-style signal connector.

32653-00

6. Replace the cover, the power cord(s) and power-up the system. Replace the system’s

cover, reconnect the power cord(s) and any network cables. Turn power on.

The LSISAS3080X-R hardware installation is complete and you are ready to install the operating
system drivers.

LINUX DRIVER INSTALLATION

Consult the Linux ReadMe.txt file on the
LSI Device Drivers & Utilities CD. LSI Logic
provides Open Source Drivers that may be
implemented in the following ways:

WINDOWS DRIVER INSTALLATION

To load the SYMMPI.SYS miniport driver during a new Windows 2000 or Windows XP system
installation or to load the LSI_SAS.SYS driver during a new Windows 2003 system installation,
you can boot directly from the Microsoft installation CD-ROM. The Windows drivers are not
interchangeable; however, the instructions are similar.

To install a new Windows operating system and its appropriate device driver, follow these steps:

1. Using another computer, copy the appropriate driver files supplied on the LSI Logic

Device Drivers & Utilities CD onto a diskette. This diskette is needed in Step 6. To create
the driver diskette, open the driver folder on the CD, and then open the folder for the
version of Windows to be installed on the new system. Next, select all folders and files
within the directory and copy them to the root directory of a clean floppy diskette.

2. Boot the computer from the Windows CD-ROM.

3. Press F6 when the words Setup is inspecting your computer's hardware

configuration appear, or when the Windows operating system prompts you for

nonsupported drivers.

NOTE: You must press F6 for the new driver to be recognized. Otherwise, the system does not

recognize the devices controlled by the driver during the Windows setup.

4. Follow the instructions until a screen displaying the words Setup could not
determine the type of one or more mass storage device appears.

• Adding precompiled binaries to an
existing installation using driver update
disks or RPMs for selected distributions.

• Adding or updating the Fusion-MPT
source in the Linux kernel for any
distribution.

TECHNICAL SUPPORT

For assistance installing, configuring, or
running the LSI22320SE, contact LSI
Technical Support:

E-mail: [e-mail]

Phone: [phone] (North America)

+44.1344.413.115 (Europe)

Web Site: http://www.lsi.com/support/

5. Choose S to specify additional devices.

6. Follow the prompts and insert the Windows driver diskette when you are prompted to

insert the hardware support disk. Select the driver version appropriate for your system.

7. Follow the Windows installation procedure to complete the installation. Microsoft

provides documentation with its installation CD-ROM.

NOTE: Refer to the Fusion-MPT Device Management User’s Guide for detailed configuration and

installation instructions for all firmware and drivers.

Version 1.0, December 2007

Find a list of LSI Corporation’s U.S. distributors, international distributors, sales offices, and design resource centers on the LSI web site
at: http://www.lsi.com

LSI and the LSI logo are trademarks or registered trademarks of LSI Corporation or its subsidiaries. All other brand and product names may be
trademarks of their respective companies.

LSI Corporation reserves the right to make changes to the product(s) or information contained herein at any time without notice. LSI Corporation
does not assume any responsibility or liability arising out of the application or use of any product or service described herein, except as expressly
agreed to in writing by LSI Corporation; nor does the purchase, lease, or use of a product or service from LSI Corporation convey a license under
any patent rights, copyrights, trademark rights, or any other of the intellectual property rights of LSI Corporation or of third parties.

Corporate Headquarters Email Website

Milpitas, CA [e-mail] www.lsi.com
800-372-2447

Document Number: DB11-000077-00
Copyright © 2007 LSI Corporation
All Rights Reserved