Installation and
User Guide
avaControl-100
1
WELCOME
Congratulations on purchasing the avaControl-100. The avaControl-100 integrates multiple
complicated control, automation and internet protocols into one simple plug-and-play device.
It is a central controller that integrated and control of all wireless Z-wave devices used for
home automation and keeps connect and control of your home easily, no matter where you
are. Please take a few minutes to read this guide to set up your avaControl-100 and Z-wave
network smoothly.
Manual version V1.00 25-12-2014
Avadesign Technology Co. Ltd.
4F.-10, No.351, Sec. 2, Zhongshan Rd.,
Zhonghe Dist., New Taipei City 23504,
Taiwan R.O.C.
www.avadesign.com.tw
2
Table of Contents
Chapter 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . 4
1.1 Benefits . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . .. . . 4
1.2 Key Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . 5
1.3 Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . 5
1.4 Hardware Overview. . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . 6
1.4.1 Front Panel and LED Indicator . . . . . .. . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . 6
1.4.2 Back Panel . . . . . .. . . . . . . .. . . . . . . . . . . . .. . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . 7
Chapter 2 Quick Install. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.1 Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . .8
2.2 The Procedure of Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
2.3 Find the IP address of your avaControl-100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . .. . . . .10
2.4 Initial setup procedure for avaControl-100 web configuration . . . . . . . . . . . . . . . . . . . .. . . .. . . . .10
Chapter 3 Full web configurations . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . .. . . . . . . .11
3.1 Enter web configure page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.2 SetZwave – Z-Wave device settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.2.1 The Z-Wave device configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.2.1.1 Add a Z-Wave device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.2.1.2 Remove a Z-Wave device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.2.2 Z-Wave Control and Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . 16
3.2.3 Topology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . .. . . . . . . . 17
3.2.4 Door Lock Security . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.2.5 Version Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3.3 Room Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.3.1 Create Room . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.3.2 All Rooms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.4 Device Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.5 Scene Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.5.1 Create Scene . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.5.2 All Scenes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . .. . . . . . 28
3.6 Trigger – Monitor the Z-Wave Devices . . . . . . . . . . . . . . . . . . . . . . ... . . . . . . . . . . . . . . . . . . . . 29
3.6.1 Create Trigger. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . 29
3
3.7 Schedule – Arrangement for Z-Wave Devices on Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
3.7.1 Create Schedule . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
3.8 Report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
3.9 Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . 33
3.9.1 Camera Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
3.9.2 Camera View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
3.10 Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
4
Chapter 1 Introduction
Avacontrol-100 is a central controller that integrated and control of all wireless Z-wave
devices used for home automation. It also provides Gateway to connect to Internet. Through
Internet you can see all kinds of devices status of your home at any time and any place via
your smartphone. You can control the home devices such as lighting, air conditioning, door
lock and unlock, you can also receive the alarm message of your home. Energy usage
monitors of your home at any time is real-time recording to the cloud host, home alarm
messages are immediately delivered to the cloud message monitoring center for the
necessary treatment.
The Avacontrol-100 controls switches, dimmers, motion sensors, temperature sensors and so
on many Z-Wave devices. Avacontrol-100 integrates complicated control, automation and
internet protocols into one simple plug-and-play device. It provides an interface that allows
you to manage your home easily, whether you are at home or not.
1.1 Benefits
No ongoing cost
Secure, remote access over the internet is FREE for all users. Send unlimited notification
emails without any pay! For sending free text messages to your mobile phone is through
Push notification.
Compatibility with all Z-Wave devices
Includes deadbolt locks, scene controllers, sensors, lighting controls, thermostats, energy
usage monitors, and even more, Avadesign lets you take advantage of everything that
Z-Wave offers, with the ability to add IP cameras, alarm panels, IR devices and so on.
Powerful applications
Avacontrol APP extends your experience, such as weather forecasting, media control,
alarm panel integration, remote live video streaming, etc.
Energy monitoring
Avacontrol advanced energy metering capabilities empower you to take control of your
electricity bill and start to save money.
Security surveillance and video monitoring
You can stream live video from plug and play IP cameras to your smartphone now! You
can also store video footage on secure servers that you can access from anywhere,
anytime.
Open API
Avacontrol-100 allows you or your developers to create new Apps to offer to all other
Avacontrol’s users.
5
No Internet Connection Required!
Even without internet access, Avacontrol can set-up and configure your wired or Wi-Fi
wireless network, allowing you to control all your devices locally.
1.2 Key Features
Provide one WAN port and four LAN port Router function
Provide two USB Host port, you can connect Z-Wave USB Dongle and 3G USB Ethernet
card
Provide compatible Z-Wave Plus communication protocol that connects all kinds of
Z-Wave devices that includes window sensors, electric locks, lighting dimmer controls,
energy usage monitor, air quality detector, temperature and humidity sensors, fire safety
sensors.
Provide a service platform to connect to the cloud service.
Provide IP-Cam viewing interface
Provide high level application program development tool interface (HTTP / CGI interface
API). System integrators can develop their own unique user interface APP.
Provide free download APP.
1.3 Technical Specifications
Technical Specifications
Hardware Specifications
CPU
CKVIUM ECONA CNS3410, 600MHZ
RAM
128MB
Flash ROM
32MB
OS
Linux 2.6.31
USB Port
USB Host 2.0 x2
Ethernet port
RJ-45 10/100Mb , support 1 WAN + 4 LAN
Physical and Environmental Characteristics
Dimensions
155(W) x 106(H) x 29(D) mm
Weight
300g
Operating
Temp. &
Humidity
Temp: 0°C~45°C (32°F~113°F)
Humidity: 10% ~ 90% relative humidity, non-condensing
Power
Adaptor
INPUT: AC100V~240V, 50/60Hz
OUTPUT: DC 12V, 2.0A
outer casing
Plastic
Approvals
FC、CE、RoHS
Country of origin
Made in Taiwan
6
Packing
Accessories
Avacontrol-100 main unit x 1 pcs
AC to DC+12V Power adapter x 1 pcs
Z-WAVE USB Dongle (ZU1401US)
USB adapter
One RJ-45 cable
Software Specifications
Protocol
Z-Wave
HA Functions
Sense Control
Lighting Control
Door Lock Control
Sensor Trigger Even
Schedule setting
Support mobile phone Push Notification
Support Devices Place Location
User account Management (admin and normal user)
Support Remote update software
Z-Wave Capacity
Support 100 Z-Wave notes
1.4 Hardware Overview
1.4.1 Front Panel and LED Indicator
RESET: If avaControl-100 encounters any system crash, you may press this button to reload
factory default value as press the button over 3 seconds or reset back to latest
configuration file while pushing the button.
: When the LED flash slowly, avaControl-100 boot successfully.
: When the LED flash slowly, avaControl-100 connects to Avadesign cloud server
successfully.
LAN: avaControl-100 provides four RJ45 type LAN ports connecting to your computer or
network device such as Hub/Switch via RJ45 cable. Light on means link 100 Mbps.
Flash when data is transmitting or receiving with 100 Mbps. Light off means
disconnected or undetected.
WAN: avaControl-100 provides one RJ45 type WAN port connecting to broadband
transmission equipment such as ADSL or Fiber or CABLE Modem via RJ45 cable.
Light on means link 100 Mbps. Flash when data is transmitting or receiving with 100
avaControl
LAN
WAN
PWR
1 1
4 3 2
RESET
Z
Z
7
Mbps. Light off means disconnected or undetected.
PWR: Light on when avaControl-100 is powered by on.
1.4.2 Back Panel
POWER: A switch for power on or off
DC 12V/2A: Connecting to AC adapter. Input AC 100V~240V, 50/60Hz;
Output DC12V 2.0A
LAN/WAN: RJ-45 socket, complied with Ethernet 10/100base-T.
USB: USB 2.0 ports, USB Type A.
LAN2
LAN3
WAN1
LAN4
LAN1
USB
1
2
POWER
DC+12V
I
O
8
Chapter 2 Quick Install
After you’ve created your Z-Wave network, you’ll need to install your AvaContorl-100. Follow
these steps:
2.1 Unpacking
Open the carton and unpack the items. Your package should include:
Avacontrol-100 main unit x 1 pcs
AC to DC+12V Power adapter x 1 pcs
Z-WAVE USB Dongle (ZU1401US)
USB adapter
One RJ-45 cable
Avacontrol-100
USB Dongle
AC/DC adapter
USB adapter
RJ-45 cable
If items are missing or damaged, notify your Avadesign representative. Keep the carton
and packing material.
2.2 The Procedure of Connection
Step 1: Plug in DC power adapter to avaControl-100.
Step 2: Connect the Ethernet cable to your AvaContorl-100 WAN port and to a network
port of your internet router.
Step 3: Connect the Z-Wave Dongle to USB adapter then connect to the USB port of your
avaContorl-100.
Ethernet cable
WAN port
9
The step 2 and step 3 have finished as above picture.
Step 4: Plug in AC power cord to power source.
Step 5: avaControl-100 begins the boot process.
Step 6: Check the earth icon LED in the front panel of avaControl-100 flash or not,
flash is ready to use.
AvaControl-100 provides three kinds of operational platforms, Web page, Android and iOS,
for users. Therefore user can configure the avaControl-100 by his/her PC or smart phone or
tablet. The web configuration guide is available in this manual. The installation guide for smart
phone/tablet with Android system or iOS system, please refer to other document.
Flash is ready to use
10
2.3 Find the IP address of your avaControl-100
Please download the Java program file named avaControlFinderJava from the website of
Avadesign Co., Ltd. http://www.avadesign.com.tw/support/support.html to your PC.
Decompress the file and click it twice by left button of your mouse. Then you will see the
IP address listing of all of your avaControl-100 as right side.
avaControl Finder
2.4 Initial setup procedure for avaControl-100 web configuration
In order to set proper functions for each Z-Wave device, you can follow this flow chart before
you start to configure avaControl-100.
START
Add the Z-wave device
Create Room
Create Scene
Create Trigger
Setup Schedule
Report
SetZwave
Please refer to section 3.2
Room
Please refer to section 3.3
Scene
Please refer to section 3.5
Trigger
Please refer to section 3.6
Schedule
Please refer to section 3.7
Report
Please refer to section 3.8
Function Name
in the top menu
11
Chapter 3 Full web configurations
3.1 Enter web configure page
Move the cursor to the IP address of avaControl-100 on the screen and click it that as shown
the diagram of avaControl Finder at section 2.3. Then you will enter the web page for
configuration as follows.
Please input with username: admin and password: admin then click “Login” button on the
screen. After login avaControl-100, you will see the home page as shown below.
At right side of home page, you can see the national flag of different country for different
language selection. Just click the national flag you will get which language you want. You also
can see the orange color button with characters of update. Click “Update” button to update
your configuration software. Finished the update procedure, you will see the screen as shown
below. A message of “This is the newest version” displays on the screen now.
Please input user
name and password.
Login
Cancel
Language selection: English, Traditional Chinese, Simplified Chinese
This message
indicates there is new
version of
configuration software
for you. You can click
the “Update” button to
update your software.
12
Home Page
After Login avaControl-100 user will see screen as above, and there are ten main
categories, user can click on each category to extend detail items.
Home
Room
Device
Camera
Scene
Trigger
Schedule
SetZwave
Report
Help
The various configuration menus are explained below. You can select various function
listed in the first line of Home page display.
3.2 SetZwave - Z-Wave device settings
One of main functions of avaControl-100 is control and monitoring the room. If you would like
to implementation of these efforts require the help of Z-Wave devices in order to complete the
task. At first, you need to add the new Z-Wave devices to avaControl-100 for control and
monitoring the room or remove the Z-wave device which not used.
3.2.1 The Z-Wave device configuration
3.2.1.1 Add a Z-Wave device
You can add the Z-Wave device by clicking on the category of “SetZwave” in the menu bar.
The procedure of adding the Z-wave device is described as follows.
Step 1: Enter the "SetZwave" page and select "Device Configuration"
13
SetZwave－Device Configuration
Step 2: Click on the "Include New Device", the screen will appear "Add Device: Waiting
for a user action."
Step 3: Press the programming switch button on the Z-Wave device for connection. The
location of programming switch button depends on the type of Z-Wave device
that you use. Please refer to the user manual of the Z-Wave device.
Step 1a: Click on “SetZwave”
category of main
menu.
Step 1b: Click on “Device Configuration” item.
Step 2: Click on “Include New Device” button.
Step 3: Press the programming switch button on the Z-wave device.
The Z-wave device was added successfully.
Plug-in on/off module
14
p.s. You also can buy these Z-Wave devices such as Plug-in on/off module, Door
sensor, PIR sensor, Wireless siren…etc. from Avadesign Technology.
Step 4: When your Z-Wave device has added successfully, the message of "Add Device:
Command has completed successfully" will display on the screen.
Step 5: When the new Z-Wave device was found, you can modify the name and room
settings as shown below.
Step 6: Then click "device", the new Z-wave device is ready to use now.
3.2.1.2 Remove a Z-Wave device
You also can remove the Z-Wave device by clicking on the category of “SetZwave” in the
menu bar. The procedure of removing the Z-wave device is described as follows.
Step 1: Enter the "SetZwave" page and select "Device Configuration"
15
SetZwave－Device Configuration
Step 2: Click on the "Exclude Device", the screen will appear "Remove Device: Waiting
for a user action."
Step 3: Press the programming switch button on the Z-Wave device for removing. The
location of programming switch button depends on the type of Z-Wave device
that you use. Please refer to the user manual of the Z-Wave device.
Step 3: Press the programming switch button
on the Z-wave device.
The Z-wave device was removed successfully.
Step 1b: Click on “Device Configuration” item.
Step 2: Click on “Exclude Device” button.
Step 1a: Click on “SetZwave”
category of main menu.
Plug-in on/off module
16
Step 4: When your Z-Wave device has removed successfully, the message of "Remove
Device: Command has completed successfully" will display on the screen.
3.2.2 Z-Wave Control and Log
AvaControl-100 provides alarm records of all Z-Wave control devices for user as follows.
SetZwave－ZwaveControl & Log
When you click on “Update” button, you will see the listing of software version updated.
Clicking on the “Version” button at the end of screen, the system will check the software
version of avaControl-100 for you automatically.
Click on “Version” button
to check the version.
You can click the
“Update” button to
download the newest
version for updating.
You also can click the “reset”
button to reset the system.
17
You also can click the “reset” button to reset the system shown as above diagram. Then you can click
on “OK” button to reset the system or “Cancel” button to quit the reset process.
3.2.3 Topology
The topology diagram shows the connection relationship of avaControl-100 and all of Z-wave
devices. The small square at row 1 and column 1 represents the avaControl-100. The small
square at row 1 and column 2 represents a Z-Wave device. Applying the topology diagram,
user can decide the control path of avaControl-100 and each Z-Wave device. For example,
the avaControl-100 can control the remote device B indirectly by device A.
SetZwave－Topology
B
A
18
3.2.4 Door Lock Security
You can select a door lock to add password or modify password.
SetZwave－Door Lock Security
Then you will see the listing of user name and password. Clicking on the pen icon to modify
the password. You also can click on the X symbol to delete the password.
You can click on the “Add” button to add new password as below. The maximum length of
password is 10 digits and you can input numeric 0 ~ 9.
Select a door lock to add or modify password.
19
You can click on the “Log” button to get the door lock records as below. The maximum
number of logs is 5. Please input the record number that equal or less than 5 then click on
“Search” button.
The “Time” button on the right side of screen is used for time setting by manually. You have to
input the right date and time by yourself. When you replace the battery of Electric Deadbolt,
please remember to modify the date and time here.
3.2.5 Version Information
Clicking on “Version Information” item, you will get the information of software version.
SetZwave－Version Information
20
3.3 Room setting
AvaControl-100 can classify and integrate all kinds of Z-Wave devices to do home
automation includes room, scene, trigger, schedule and report.
3.3.1 Create room
Create rooms to distribute Z-Wave devices
According to the different room in the family, you can distribute the Z-Wave devices to each
room. And you can learn which room was invaded or controlled household appliances
quickly.
Now, you can create a new room by clicking on “Create Room” item. Then input the room
name and click on “Add” button.
Room－Create Room
You also can change the icon of the room by clicking on “Change ICON” button. Then you will
see some pictures that you can choose for the proper room as below screen.
Please input the room name. Then click on “Add” button to create a
new room.
21
If you change icon and input “meeting room” in the field of room name, and click on “Add”
button.
Then you will see the meeting room appear on the left side of screen.
Kitchen
Study room
Bathroom
Bedroom
Living room
or
Meeting room
Dining room
Hallway
Congratulation! You have created a meeting room
successfully.
22
3.3.2 All rooms
You can see the device status in each room easily by clicking on “All rooms” item.
3.4 Device setting
You can place the Z-wave device in the right room by selecting device function in the top
menu and choosing a device which you want.
For example, you create a meeting room at section 3.3, and you would like to place light
device in this room. The setting procedure is described as following:
Step 1: Select “Device” function and clicking on “All Devices” item to show all of the
Z-Wave devices on the screen.
Step 2: Choose the device that you need and click on the icon of pen to edit the content
of device. For example, you place light device in this room.
Please refer to the following screen.
23
Device－All Devices
Step 2: Edit
Step 1
24
Step 3: Edit the content of light device. Please input the device name and room name.
Then click on “Save” button to save the configuration. You also can check this
node by clicking on “Check and Remove” button and the message of “The node
is OK” displays on the screen.
Step 4: Go back to “Room” function and click on “Meeting room” item, then you will see
the light device
Room－Meeting room
Now, you can place another device to other room continuously. For example, you want
to place electronic deadbolt in hallway. Please refer to the following screens.
25
Then you will find the electronic deadbolt in hallway now.
26
3.5 Scene Setting - Control Z-Wave devices
You can control and combine a number of Z-Wave devices together and execute a designed
operation action by clicking one key only.
3.5.1 Create Scene
Step 1: Select "Scene" function in the top menu on the screen. Then click on “Create Scene”
item. Please input the scene name and click on “Add” button.
Scene－Create Scene
Step 2: Now, you can see the scene was created and named as “Turn on the light for meeting
room”. You also can edit the scene name by clicking on the icon of pen.
You also can edit the scene
name by clicking on the icon of
pen.
27
Then add controlled Z-Wave devices in this scenario that shown as below. For
example: you add a switch of light in this scenario.
You can add more controlled Z-Wave devices in this scenario by selecting one device
in the scrolling menu and clicking on the icon of plus sign on the screen. Then you will
see a new controlled device display on the screen now.
You also can delete a controlled Z-Wave device in this scenario by clicking on the
icon of “X”. Then you will see this controlled device disappear on the screen now.
Step 3: Setting the proper action for each device. For example: you can turn on the light by
clicking on “On” button. Then you will see the color of light has changed to bright
yellow.
Delete a controlled Z-Wave device
in this scenario by clicking on the
icon of “X”.
Scrolling menu
Add a new device
28
Step 4: You can click on “Run” button of the scene that has set by yourself. The
corresponding Z-Wave device will be used.
3.5.2 All Scenes
You can see all of scenes by clicking on “All Scenes” item and select the scene that you want
to execute.
29
3.6 Trigger - Monitor the Z-Wave devices
3.6.1 Create Trigger
The trigger function is used to monitor the setting of Z-wave devices, when an alarm is
triggered to launch. Please refer to the following diagram for alarm setting.
Trigger－Create Trigger
You also can combine both of trigger and scene functions setting. For example: when people
enter the meeting room, the light will be turn on automatically. Input the trigger situation and
select a scene by clicking on the scrolling menu.
30
Then press the “Save” button. You will see the screen as below.
3.7 Schedule – Arrangement for Z-Wave devices on schedule
3.7.1 Create Schedule
You can set up a schedule to monitor the security of your home regularly. For example: When
nobody at home on Saturday set up to open the Z-Wave device automatically for monitoring.
Please click the check square of every week and select the day and time from the scrolling
bar. And select the scene that you wanted and input the name of schedule. Then click on
“Save” button to save the configuration of schedule.
A new trigger is created and displays on
the left of screen.
You also can modify the trigger and
mode by clicking on “Modify” button.
31
Schedule－Create Schedule
Now you will find a new schedule of “alert on Saturday” is created and displayed on the
screen.
3.8 Report
You can get the power consumption of the Z-Wave device by using the report function. This
function requires purchase the Smart Energy Switch device to monitor the amount of current.
You can see how much power was used at which time period as shown below.
Step 1: At first, select a device and unit. Then input time period.
You also can modify the schedule
name by clicking on “Modify” button.
You can decide whether the alarm active
or not by clicking on the check square.
32
Report
Step 2: Click on “Search” button. Please waiting for few seconds, then the result is displayed
on the screen.
Amount of electricity consumption
33
3.9 Camera
You can connect and control all of cameras in the house by the function of camera.
3.9.1 Camera Setting
You can add a camera by clicking on the icon of “+” or remove a camera by clicking on the
icon of “X” or edit and modify the configuration of camera by clicking on the icon of pen as
shown below.
Camera – Camera Setting
Add a Camera
Please input the camera name, IP address of camera, camera port, camera URL, MJPG URL,
camera account and password. Then click on “OK” button to save the configuration.
You also can edit and modify the configuration of camera as shown below.
Add a camera
Remove a camera
Edit and modify the configuration of camera
34
Edit and Modify
3.9.2 Camera View
You can view the real-time image by clicking on “Camera View” or the camera name.
35
3.10 Help
The function of help in the top menu on the screen will assist you to understand how to set up
and use the avaControl-100 by hyperlink to Avadesign company web page to download those
documents that you need.
Loading...