AutoPatch 8Y-XL, 8Y-3000 Installation And Setup Manual

Download

8Y-3000 Documentation Set

8Y-3000 New Features

8Y-3000 Installation and Setup Guide

8Y-3000 User’s Operation Manual

8Y-3000 New Features

This manual contains information for the 8Y-3000 Distribution Matrix, an

advanced 8Y-XL system with the following additional features:

32-bit processor

Link to other AutoPatch products with an XNNet network compatible

interface

Link to a larger line of XNNet AutoPatch control accessories

– Next Generation SBCs (with real-time status update) – SDU – CP-32 – CP-20 –CP-10 – Precis Remote Panel

Controllable via Ethernet, Neuron, RS-232/RS-422, and a variety of

Net-based control panels – 10 Base-2 Ethernet interface – Neuron Control network @ 76 Kbps, free topology – Software selectable RS-232 or RS-422 – Serial port BAUD rate up to 57600 – Serial port Hardware/Software Handshaking

New, more powerful, virtual matrix structure and easy configuration

via X

Connect software

Individual crosspoint disconnect capability

Field upgradeable software

Literal switch does not invalidate status

Preset request does not invalidate status

Note: The 8Y-3000 processor does not link and communicate with older

8Y-XL processors.

8Y-XL Installation and Setup Guide

Version A0

Version B0 905197

CAUTION

To avoid ESD (Electrostatic Discharge) damage to sensitive components, make

sure you are properly grounded before touching any internal materials.

When working with any equipment manufactured with electronic devices,

proper ESD grounding procedures must be followed to ensure people, products,

and tools are as free of static charges as possible. Grounding straps, conductive

smocks, and conductive work mats are specifically designed for this purpose.

Anyone performing field maintenance on AutoPatch equipment should utilize an

appropriate ESD field service kit complete with at least a dissipative work mat

with a ground cord and a UL listed adjustable wrist strap with another ground

cord. These items should not be manufactured locally, since they are generally

composed of highly resistive conductive materials to safely drain static charges,

without increasing an electrocution risk in the event of an accident. ESD

™

protective equipment can be obtained from 3M

Technology

, Plastic Systems®, and other such vendors.

, Desco®, Richmond

Installation and Setup Guide

Important Safety Information and Instructions

When using and installing your AutoPatch product, adhere to the following basic safety precautions. For more information about operating, installing, or servicing your AutoPatch product see your product documentation.

Read and understand all instructions before using and installing AutoPatch products.

Use the correct voltage range for your AutoPatch product.

There are no user serviceable parts inside an AutoPatch product; service should only

be done by qualified personnel.

If you see smoke or smell a strange odor coming from your AutoPatch product, turn

it off immediately and call AutoAssist.

Turn off and unplug an enclosure before adding or removing boards, unless otherwise

specified in that product’s documentation.

To avoid shock or potential ESD (Electrostatic Discharge) damage to equipment,

make sure you are properly grounded before touching components inside an AutoPatch product.

For products with multiple power supplies in each unit, make sure all power supplies

are turned on simultaneously.

Use surge protectors and/or AC line conditioners when powering AutoPatch products.

Only use a fuse(s) with the correct fuse rating in your enclosure.

Make sure the power outlet is close to the product and easily accessible.

Make sure the product is on or attached to a stable surface.

Turn off equipment before linking pieces together, unless otherwise specified in that product’s documentation.

For safety and signal integrity, use a grounded external power source and a grounded power connector.

Installation and Setup Guide

Information et directives de sécurité importantes

Veuillez vous conformer aux directives de sécurité ci-dessous lorsque vous installez et utilisez votre appareil AutoPatch. Pour de plus amples renseignements au sujet de l’installation, du fonctionnement ou de la réparation de votre appareil AutoPatch, veuillez consulter la documentation accompagnant l’appareil.

Lisez attentivement toutes les directives avant d’installer et d’utiliser les appareils

AutoPatch.

Le voltage doit être approprié à l’appareil AutoPatch.

Les appareils AutoPatch ne contiennent aucune pièce réparable par l’usager; la

réparation ne doit être effectuée que par du personnel qualifié.

Si de la fumée ou une odeur étrange se dégagent d’un appareil AutoPatch, fermez-le

immédiatement et appelez le Service de soutien technique (AutoAssist).

Fermez et débranchez le boîtier avant d’ajouter ou d’enlever des plaquettes, à moins

d’indication contraire fournie dans la documentation du appareil.

Pour éviter les chocs ou les dommages éventuels causés à l’équipement par une

décharge électrostatique, veillez à ce le dispositif oit bien relié à la terre avant de toucher les composantes se trouvant à l’intérieur d’un appareil AutoPatch.

Veillez à ce que tous les blocs d’alimentation des appareils dotés de blocs d’alimentation multiples dans chaque unité soient allumés simultanément.

Servez-vous de protecteurs de surtension ou de conditionneurs de lignes à courant alternatif lorsque vous mettez les appareils AutoPatch sous tension.

Placez uniquement des fusibles de calibre exact dans les boîtiers.

Veillez à ce que la prise de courant soit proche de l’appareil et facile d’accès.

Veillez à ce que votre appareil AutoPatch soit installé sur une surface stable ou qu’il y soit fermement maintenu.

Fermez toutes les composantes de l’équipement avant de relier des pièces, à moins d’indication contraire fournie dans la documentation de l’appareil.

Par mesure de sécurité et pour la qualité des signaux, servez-vous d’une source d’alimentation externe mise à la terre et d’un connect d’alimentation mis à la terre.

Installation and Setup Guide

Notices

stored in a retrieval system, or transmitted, in any form or by any means, electronic,

mechanical, photocopying, recording, or otherwise, without the prior written permission

of AutoPatch. Copyright protection claimed extends to AutoPatch hardware and software

and includes all forms and matters copyrightable material and information now allowed

by statutory or judicial law or here in after granted, including without limitation, material

generated from the software programs which are displayed on the screen such as icons,

screen display looks, etc. Reproduction or disassembly of embodied computer programs

or algorithms is expressly prohibited.

No patent liability is assumed with respect to the use of information contained herein.

While every precaution has been taken in the preparation of this publication, AutoPatch

assumes no responsibility for error or omissions. No liability is assumed for damages

resulting from the use of the information contained herein.

Further, this publication and features described herein are subject to change without

notice. The United States Federal Communications Commission (in 47CFR 15.838) has

specified that the following notice be brought to the attention of the users of this product.

Federal Communication Commission Radio Frequency Interference Statement:

“This equipment generates and uses radio frequency energy and if not installed and used

properly, that is, in strict accordance with the manufacturers instructions, may cause

interference to radio and television reception. It has been type-tested and found to

comply with the limits for a Class B computing device in accordance with the

specifications in Subpart J of Part 15 of FCC Rules, which are designed to provide

reasonable protection against such interference in a residential installation. However

there is no guarantee that interference will not occur in a particular installation. If this

equipment causes interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

Reorient the receiving antenna

Relocate the matrix with respect to the receiver

Move the matrix away from the receiver

Plug the matrix into a different outlet so that computer and receiver are on different branch circuits

Installation and Setup Guide

If necessary, the user should consult the dealer or an experienced radio/television

technician for additional suggestions. The user may find the booklet, How to Identify and

Resolve Radio-TV Interference Problems, prepared by the Federal Communications

Commission to be helpful.”

This booklet is available from the U.S. Government Printing Office, Washington, D.C.

20402, Stock N. 004-000-00345-4.

™,XN

8Y-XL

Net™, and XNConnect™are trademarks of XNTechnologies, Inc.

Use shielded cables. To comply with FCC Class B requirement, all external data

interface cables and adapters must be shielded.

MS-DOS, Windows, and Windows95 are registered trademarks of Microsoft

Corporation.

3M, Desco, Richmond Technology, and Plastic Systems are all registered trademarks.

Neuron

and LonTalk®are registered trademarks of Echelon.

Installation and Setup Guide

AutoPatch Statement of Warranty

AutoPatch, a division of XNTechnologies, Inc., Cheney, Washington, warrantees that the products manufactured by AutoPatch will be free of defects in materials and workmanship for the lifetime of the product, subject to the following terms and conditions.

Terms and Conditions

1. AutoPatch products are under warranty for a period of five (5) years

following the original sales invoice date. The warranty period may be extended to the life of the product provided the warranty card is filled out and returned to AutoPatch. TO VALIDATE THE LIFETIME WARRANTY: THE AutoPatch WARRANTY CARD MUST BE FILLED OUT BY THE DEALER AND RECEIVED BY AutoPatch WITHIN THIRTY (30) DAYS OF THE INSTALLATION OF EQUIPMENT BUT NO LATER THAN ONE (1) YEAR FROM THE ORIGINAL SALES INVOICE DATE. A warranty certificate will be returned to the dealer to verify the warranty period.

Warranty

2. This Limited Lifetime warranty covers AutoPatch products shipped on or after October 1, 1997. The Limited Lifetime warranty applies to products in the original installation only. If the product is moved to a different installation, the Limited Lifetime warranty will no longer apply and the product warranty will revert to the original warranty which covers a period of five (5) years following the original sales invoice date.

3. The product lifetime is defined as the period of time from the original sales invoice date to ten (10) years after AutoPatch ceases manufacturing the product model.

4. Warranty repairs are accomplished by returning the subassembly to AutoPatch for repair. If conditions do not permit this procedure, AutoPatch will invoice new or reconditioned (at AutoPatch’s option) replacement parts and ship them to the dealer or to the customer if so directed by written order from the dealer. In that case the replacement will be billed to the customer and the customer may return the failed subassembly within 30 days for credit. See “AutoPatch Returns Policy” in this manual for replacement policies and procedures.

Installation and Setup Guide

Warranty

5. AutoPatch’s liability and Buyer’s remedies under this warranty shall

be limited solely to repair, replacement, or credit, at AutoPatch’s option.

6. The AutoPatch warranty does not apply to any AutoPatch product that has been modified, repaired by an unauthorized agent, or improperly installed, used, or maintained. AutoPatch shall not be liable under any circumstances for consequential or incidental damages including, but not limited to, labor costs or loss of profits arising in connection with the use of or inability to use AutoPatch products.

7. AutoPatch will not be responsible for items damaged during shipment to or from AutoPatch. The shipping carrier is responsible for items damaged during shipment.

8. This warranty is exclusive and in lieu of any other warranty, expressed or implied, including but not limited to any implied merchantability or fitness for a particular purpose. The terms of this warranty are governed by the laws of the state of Washington; certain other states restrict warranty limitations. You may have rights that are not defined herein.

9. This warranty may not be modified except in writing by an authorized AutoPatch officer.

Installation and Setup Guide

Contents

Welcome

Installer’s Product Notes ........................................ii

Meet the Manual...............................................iii

Terms to Know ................................................iv

Technical Support ..............................................v

Chapter 1 – Unpacking the 8Y-XL

Front of the Enclosure ........................................1-2

CP-10 Control Panel......................................1-3

Rear of the Enclosure ........................................1-6

Chapter 2 – Placing the Enclosure(s)

Chapter 3 – Linking Enclosures

Chapter 4 – Attaching Inputs and Outputs

Attaching Input and Output Cables .............................4-2

Paralleling Inputs.............................................4-4

Chapter 5 – Attaching an External Controller

Chapter 6 – Applying Power and the Startup Sequence

Applying Power ..............................................6-2

Startup from the CP-10 Control Panel..........................6-2

Startup from a Control Device .................................6-3

Chapter 7 – Executing a Test Switch

Executing a Test Switch Using CP-10 Control Panel..............7-2

Executing a Test Switch Using BCS Commands .................7-4

Installation and Setup Guide

Chapter 8 – Managing Configuration Files

Conceptual Overview .........................................8-2

Installing and Launching ......................................8-2

Panes, Views, and Dialog Boxes................................8-3

Opening and Downloading a Configuration File...................8-4

Modifying Configuration Files ..................................8-5

Configuring Local Presets.................................8-5

Modifying Groupings......................................8-8

Chapter 9 – Adjusting Gain

Chapter 10 – Adding Hardware

Adding Boards .............................................10-2

Input and Output Boards ................................10-2

Vertical Interval Timing Board ............................10-3

Adding Enclosures ..........................................10-5

Appendix A – AutoPatch Service and Returns Policy

Service......................................................A-1

Return Authorizations ....................................A-1

Claims for Shipping Damages .............................A-1

Replacement Policies and Procedures .........................A-2

Special Notice ...............................................A-3

Appendix B – Product Specifications

General .....................................................B-1

Analog Audio ................................................B-2

Standard Audio Boards ...................................B-2

Analog Video ................................................B-3

Standard Video Boards ...................................B-3

Wideband Video Boards ..................................B-4

Ultra-wideband Video Boards..............................B-5

Appendix C – BCS (Basic Control Structure) Commands

Glossary

Index

Installation and Setup Guide

Welcome

Welcome to the 8Y-XL Installation and Setup Guide. This book is the

first part of a three document set:

Installation and Setup Guide – compiled for the technician installing

the system.

User’s Operation Manual – created for the end-user who operates the

system.

Quick Reference Guide – a companion to the User’s Operation Manual.

The 8Y-XL Installation and Setup Guide is designed to provide the

installation technician with quick, easy-to-follow instructions for

installing an 8Y-XL and preparing it for operation.

Welcome

The 8Y-XL User’s Operation Manual does not include any detailed

information about SBCs (Single Bus Controllers) for the 8Y-XL. Call

AutoAssist for more information about this controller type (see Technical

Support,p.v).

Installation and Setup Guide i

Welcome

Installer’s Product Notes

An 8Y-XL Distribution Matrix can stand alone or comprise a virtually

unlimited number of linked enclosures, including any other AutoPatch

products with an X

enclosure can hold up to 8 input and 8 output boards and each board can

have up to 8 connectors, for a total capacity of 64 inputs and 64 outputs

per enclosure.

8Y-XL Distribution Matrices fit in a broad range of audio/video

environments and are controllable from a variety of sources, including a

CP-10 Control Panel, a CP-10 Remote Control Panel, any control device

that can send ASCII characters through an RS232 or RS422 serial cable,

a third party serial controller*, a PC, or a Single Bus Controller*.

Tools for Installation:

Net network compatible interface. Each 8Y-XL

A laptop computer with an RS232 or RS422 null modem cable

(communication with the 8Y-XL via a serial port for programming

and fault isolation)

q The AutoPatch Configuration Software set (which includes copy of

the configuration file) shipped with the system

The full set of user documentation shipped with the system

*These control devices are not covered in this document.

ii Installation and Setup Guide

Meet the Manual

This manual contains 10 chapters and 3 appendices. The information in

this manual progresses from unpacking the 8Y-XL in Chapter 1 to BCS

(Basic Control Structure) commands in Appendix C. Use the following

chapter descriptions to guide you through the manual.

Title Description

Items included in shipping and unpacking tips

Chapter 1

Unpacking the 8Y-XL

Chapter 2

Placing the Enclosure(s)

Chapter 3

Linking Enclosures

Chapter 4

Attaching Inputs and Outputs

Chapter 5

Attaching an External Controller

Chapter 6

Applying Power and

the Startup Sequence

Chapter 7

Executing a Test Switch

Chapter 8

Managing Configuration Files

Chapter 9

Adjusting Gain

Description of the enclosure’s physical features

List of tools needed for installation

Steps for placing the enclosure(s)

Information on linking enclosures

Directions for attaching input and output cables

Directions for paralleling inputs

Directions for attaching an external control

device to an enclosure

Directions for applying power

ä ä Startup sequence from the CP-10 Control Panel ä Startup sequence from a serial control device

ä Directions for executing a test switch from the

CP-10 Control Panel

ä Directions for executing and disconnecting a

test switch using BCS commands

ä Conceptual overview and screen description of

Connect

ä Directions for installing and launching

Connect

Directions for opening and downloading configuration files

Directions for modifying configuration files

Directions for adjusting gain

Welcome

Chapter 10

Adding Hardware

Appendix A

AutoPatch Service and

Returns Policy

Appendix B

Product Specifications

Appendix C

BCS (Basic Control Structure)

Commands

Glossary

Index

Directions for adding boards and enclosures to expand system switching capabilities

Details regarding AutoPatch Service and Returns policies

Technical specifications and performance information

BCS characters, functions, and descriptions in chart format

Definitions of terms as they are used in this manual

Index of subjects by features and tasks

Installation and Setup Guide iii

Welcome

Terms to Know

Before jumping into the technical details of this manual, you should be

familiar with the following terms:

Welcome

Basic Control Structure (BCS)

BCS is a set of alphanumeric characters that combine to form command

lines. Use BCS to control a system from any serial device that allows you

to enter characters, such as a PC (personal computer).

Configuration File

A configuration file is a text file containing system configuration

information referenced by each enclosure’s CPU during any type of

switch operation. If a system has multiple enclosures linked together,

configuration information uploaded to any 8Y-XL enclosure is

automatically shared with the rest of the linked enclosures in the system.

CP-10 Control Panel

The CP-10 Control Panel is attached to each enclosure and is designed

for system control of the 8Y-XL Distribution Matrix.

ESD

Electrostatic Discharge (ESD) refers to electrical charges (such as static

electricity) that can damage sensitive components inside an enclosure.

The graphic to the left of this definition precedes every procedure where

ESD damage could occur if you are not properly grounded and not

handling components correctly (see the Caution page inside the front

cover of this guide for more details about ESD).

Input and Output Connectors

Input and output connectors are on the rear of an enclosure. Input and

output signal cables attach to the input and output connectors. Standard

8Y-XL audio and data connectors are 3-position terminal block; video

and sync connectors are BNC.

Level

A level is a set of input and output signals that are grouped and,

therefore, switch together. In a configuration file, a level is referred to as

a “virtual matrix.”

iv Installation and Setup Guide

Technical Support

Signal

A signal can be analog audio, analog video, serial digital, sync

information, or other types. A signal (also called an input or output

signal) comprises of a set of connectors whose signals switch together,

such as an “RGB” signal. To route a specific input (source) signal to a

specific output (destination) device, the input and output signals must be

of the same signal type and share the same level designation.

Switch

A switch is an active connection between an input (source) signal and

one or more output (destination) devices.

Connect

Connect is graphical software program that displays your most recent

configuration and allows easy addition of local presets and modification

of other configuration information (see the X

Connect Help file for

assistance).

Welcome

Net

Net is an internal communication protocol that requires software

driver support for Ethernet and Neuron

interfaces.

Technical Support

AutoPatch provides technical support 24 hours a day, 7 days a week

(except for U.S. holidays). Before calling with a question, please consult

the 8Y-XL documentation. If these manuals cannot fully answer your

question, have your serial number (located on the plate between the

input and output connectors on the rear of the enclosure) ready and call

your authorized AutoPatch dealer or call AutoPatch AutoAssist at: (toll

free for U.S. and Canada) 800-622-0246 or (international) 509-235-2636.

You can also reach us through our web site: www.autopatch.com,or

e-mail our AutoPatch Technical Support Specialists at:

support@autopatch.com.

Installation and Setup Guide v

Unpacking the 8Y-XL

The 8Y-XL is shipped with one enclosure in each shipping box. Each

box contains one of each of the following items (invoices are sent

separately):

Power cords (one per enclosure)

Enclosure

The shipping boxes are marked as “Box #_of_,” where the first blank is

the box number and the second blank is the total number of boxes in the

shipment. Box #1 contains several additional items:

Packing list

Installation and Setup Guide

User’s Operation Manual

Quick Reference Guide (inside binder)

AutoPatch 8Y-XL Connector and Groupings Guide

Unpacking

AutoPatch Configuration Software set

Link cable (included with multi-enclosure systems)

Other enclosure products

Installation and Setup Guide 1-1

Unpacking the 8Y-XL

Unpacking Tips

Before fully unpacking the enclosure(s), examine the shipping

box(es) for any signs of damage. If a box is partially crushed or any

sides have been broken open, notify the shipping agency

immediately and contact your AutoPatch Salesperson or

Representative.

Once unpacking is complete, closely check the physical condition of

the enclosure(s).

Collect all documentation and envelopes.

Unpacking

Note: AutoPatch is not responsible for damage caused by insufficient

packing during return shipment to the factory. Upon request, AutoPatch

will supply new shipping boxes at cost.

1.1 Front of the Enclosure

Enclosures are the structural basis of an 8Y-XL Distribution Matrix.

Since AutoPatch matrix switchers are custom-built for each installation,

factors such as control method, signal type, and potential switches affect

the appearance and weight of each enclosure.

An enclosure can have a blank front panel or a CP-10 Control Panel (a

front panel that is produced by AutoPatch and has an LCD screen and

keys for entering commands). Although a CP-10 Control Panel is

optional, we recommend one on at least one enclosure in the system for

system verification, redundant control, and troubleshooting. The CP-10

Control Panel can be attached or removed as needed.

1-2 Installation and Setup Guide

LCD Screen

Front of the Enclosure

CP-10 Control Panel

power

Arrow Keys

CANCE L

STATUS

INPUT

SPECIAL PRESET

CHANGE

LEVEL

OUTPUT

UNDO

BACKLIGHT

PROGRAM

TAKE

SPACE

Front view of an 8Y-XL enclosure with a CP-10 Control Panel

A CP-10 Control Panel has 29 keys – 10 number keys for entering digits,

4 directional arrow keys, and 1 each of the following: Cancel, Take,

Status, Level, Change, Input, Output, Preset, Program, Backlight, Space,

Special, Undo, Comma, and Period (the last four are not implemented).

To use the CP-10 Control Panel, use the keys to choose commands and

values from the Command Screen.

To choose a command, push the key that corresponds with the one you

want to choose.

Unpacking

To select values for fields (such as Level, Source, Destination, and

Preset values), use the number keys.

Number Keys (0-9)

Use the number keys to enter digits when choosing front panel menu

items (instead of scrolling down the lists), entering input, output, and

local preset numbers, and entering digits for any other functions that may

require numbers.

Arrow Keys

Use the arrow keys to scroll left and right through long lists of outputs.

The arrow keys are required only when an arrow graphic is displayed on

the front panel’s LCD screen.

Installation and Setup Guide 1-3

Unpacking the 8Y-XL

Cancel Key

Use the Cancel key to abort a command that is incomplete. If you make a

mistake while entering a command, press the Cancel key to remove the

partially entered command from the screen and enter the correct

command. The Cancel key cannot undo a completed operation.

Take Key

The Take key is much like the Enter or Return key on a computer

keyboard. Pressing the Take key tells the system to execute the chosen or

entered command.

Unpacking

Status Key

Use the Status key to query the system for signal routing information and

switch verification.

Level Key

The Level key prepares the system to receive a level identification

number as the next entry.

Change Key

Use the Change key to switch signals. Press the Change key and the

Change menu appears, prompting you for information about the switch

you want to perform.

Input Key

The Input key prepares the system to receive an input identification

number as the next entry.

Output Key

The Output key prepares the system to receive an output identification

number as the next entry.

Preset Key

Use the Preset key to implement a local preset.

1-4 Installation and Setup Guide

Front of the Enclosure

Backlight Key

The Backlight key illuminates the LCD. The backlight remains

illuminated for approximately 20 seconds; however, you can turn it off

before the 20 seconds are up by pressing the key again.

Space Key

Use the Space key to insert a space between multiple outputs or multiple

local presets when entering a command; the output and local preset

prompts are the only prompts that accept multiple entries.

Special, Program, Undo, Comma (,), and Period (.) Keys

These keys are not implemented at this time.

Unpacking

Installation and Setup Guide 1-5

Unpacking the 8Y-XL

1.2 Rear of the Enclosure

All the enclosure’s connectors (input and output, XNNet, serial, Ethernet,

and power) are on the rear of the enclosure. Audio and video input and

output connectors, the CPU, expansion/control slots, the power supply,

(AC powered entry), and the serial number are all on the rear of the

enclosure.

The following segments briefly introduce the hardware on the rear of an

enclosure.

Unpacking

Fuse Drawer

Power Switch

Power Connector

Optional Redundant Power Supply

Serial Number

Expansion/Control Slot

Ethernet Status Indicator

System Status Indicator

Expansion/Control Slot

Power Supply

COMM

STATUS

LINK1

Ethernet Port

PORT1

Serial Ports

Fan Vent

LINK2

PORT2

15 16

25 26

15 16

17 18

27 28

25 26

X Net Communication Link Port

CPU Board

5758

162

37393

8454

655

Inputs

Outputs

3536

59 6

3536

59 6 0

Input and Output Connectors

Input and output connectors are the attachment points for devices that

connect to the system. The inputs (sources) are on the top of the

enclosure, to the right of the power supply, and the outputs (destinations)

are on the bottom of the enclosure, to the right of the CPU. A single

enclosure can handle a combination of analog audio, analog video,

digital video, and sync signals.

1-6 Installation and Setup Guide

Rear of the Enclosure

CPU

The CPU is in one of the expansion/control slots to the left of the output

connectors and has connectors (ports) for attaching external control

devices. The CPU also has a system status light, a network use light

(Ethernet Status indicator), and ports for linking to other enclosures.

Expansion/Control Slots

Each enclosure provides three expansion/control slots. One contains the

CPU board and two are for future boards that will increase functionality

and add new features to your system. One is located above the CPU and

one is below it.

Power Supply

The power supply is on the top left corner of the rear of the enclosure.

The power supply holds the power switch, power connector, and fuse

drawer. The power supply fan vent is to the right of the power supply

unit.

The 8Y-XL input voltage range is AC 100-240V single phase. The

power supply will accept all major, international, standard power sources

(see page B-1 for power supply specifications).

The fuse drawer is just above the power switch and contains two 2 AMP

Time Delay (5mm x 20mm) fuses.

Press the “0” side of the power switch to turn power off; press the “1”

side to turn it on.

Unpacking

We recommend surge protectors and/or an AC line conditioner.

Serial Number

The serial number for the system is located on the plate between the

input and output connectors.

Installation and Setup Guide 1-7

Placing the Enclosure(s)

You can install 8Y-XL enclosures in a standard EIA 19 in. (48.26 cm)

rack. To hold enclosures in place, they are shipped with rack installation

ears already attached.

To make control panel operations easier, mount the enclosure with the

CP-10 Control Panel attached in the rack at eye level. The optimum

viewing angle for the LCD screen is 15°. Install a multi-enclosure system

with all the enclosures linked, so control information can travel between

them.

Caution: Avoid placing high heat-producing equipment directly above

or below the enclosure(s). 8Y-XL enclosures are designed to adequately

dissipate the small amount of heat they produce under normal operating

conditions; however, this design is defeated when high heat-producing

equipment is placed directly above or below the enclosure(s).

Tools you will need to place enclosure(s):

Placing

Screwdriver

Screws that fit your rack [for mounting the enclosure(s)]

Link cables (included with multi-enclosure systems, otherwise not

needed)

Enclosure(s)

Standard EIA 19 in. (48.26 cm) rack

Surge protector(s) – highly recommended

Installation and Setup Guide 2-1

Placing the Enclosure(s)

To install an enclosure in a rack:

1. Place the enclosure in the rack and attach front-mounting screws to

hold it firmly in place (repeat for each enclosure). You may find it

easiest to install the top enclosure first and move down from there.

power

CANCEL

CHANGE

LEVEL

STATUS

OUTPUT

INPUT

PROGRAM BACKLIGH T

PRESET

SPECIAL

TAKE

SPACE

UNDO

Placing

2. If you have a multi-enclosure system, link the enclosures. See

Chapter 3, "Linking Enclosures."

3. Following the 8Y-XL Connector and Groupings Guide, attach only

the first two input and output signals to the correct input and output

connectors on the rear of the correct enclosure. See Chapter 4,

"Attaching Inputs and Outputs."

4. Attach power to each enclosure and turn on the entire system. See

Chapter 6, "Applying Power and the Startup Sequence." WE

RECOMMEND SURGE PROTECTORS AND/OR AN AC LINE

CONDITIONER

5. Perform a test switch to ensure the system is working properly. See

Chapter 7, "Executing a Test Switch."

6. When the test switch works correctly, attach all the input and output

cables to the correct input and output connectors on the rear of each

enclosure. Refer to Chapter 4, "Attaching Inputs and Outputs" and

the "8Y-XL Connector and Groupings Guide."

If the test does not work correctly, see Chapter 7, “Executing a Test

Switch.”

2-2 Installation and Setup Guide

Linking Enclosures

An 8Y-XL enclosure can connect to other enclosures and any other

AutoPatch product with an X

enclosures to products using any of the ports on the CPU; however, serial

port linking requires a special configuration file. We recommend linking

enclosures via the Ethernet ports.

Link enclosures in a multi-enclosure system so that control information

can pass between them.

Link Port Cable Type Space between Enclosures (max)

Ethernet (these cables

are included with

multi-enclosure systems)

Net 16 gauge twisted pair 492 ft. (150 m)

In a multi-enclosure system with an external controller, the enclosure

connected to the control device receives all control information and

passes on relevant information to other enclosures via the links. An

8Y-XL can have a virtually unlimited number of linked enclosures.

Net compatible interface. You can link

RG-58 492 ft. (150 m)

Linking

When linking enclosures within a system, we recommend connecting

them with the Ethernet ports for consistent control speed.

Note: If any of the linked enclosures were not in your original system,

you need a new configuration file (call AutoAssist; see Technical

Support, page v).

You can link 8Y-XL enclosures using link cables and the connectors on

the CPU (see the linking diagrams on the following pages).

Installation and Setup Guide 3-1

Linking Enclosures

Note: Termination connectors are required on the open ends of all “T”

connectors when linking enclosures.

To link an 8Y-XL enclosure to a Modula enclosure using Ethernet

link connectors:

1. Fasten “T” connectors to the Ethernet ports on both enclosures.

2. Fasten the connectors on the ends of the Ethernet link cable onto the

“T” connectors. Add termination connectors as shown in the graphic

below.

3536

15 16

4950

59 6

655

Linking

COMM

STATUS

LINK1

PORT2

PORT1

17 18

LINK2

25 26

Link enclosures using Ethernet connectors

15 16

162

655

3536

59 6

5758

Termination Connectors

3-2 Installation and Setup Guide

To link an 8Y-XL enclosure to a Modula enclosure using the XNNet

Communication link connectors:

1. Insert the wires on one end of the link cable into the X

Net terminal

block on the first enclosure as shown in the graphic below.

2. Insert the wires on the other end of the link cable into the X

Net

terminal block on the second enclosure in the same way as in step

one.

3536

15 16

25 26

15 16

COMM

STATUS

LINK1

PORT2

PORT1

17 18

LINK2

25 26

27 28

59 6

3536

51495

5758

960

162

8454

655

Link enclosures via their X Net Communication link ports

Linking

Installation and Setup Guide 3-3

Attaching Inputs and Outputs

Inputs and outputs attach to the input and output connectors on the rear

of each enclosure. Inputs attach to the connectors on the upper part of the

enclosure, and outputs attach to the connectors on the lower part of the

enclosure. The input and output connectors are numbered separately. The

numbering starts at the top left and goes across two connectors. This

pattern repeats downward to the bottom of the section and then continues

from the top on the remaining two sets of connectors on the right.

Connectors on an 8Y-XL enclosure could include:

Signal Type Connector Type

Analog audio (balanced or unbalanced)

Digital audio BNC

Analog video BNC

Digital video BNC

Sync BNC

Pluggable 3 position terminal block

Inputs and Outputs

Installation and Setup Guide 4-1

Attaching Inputs and Outputs

4.1 Attaching Input and Output Cables

When attaching input and output signal cables, refer to the sheet labeled

"AutoPatch 8Y-XL Connector and Groupings Guide" that was included

in the shipping box(es). The sheet shows you where to attach each signal

cable on the rear of each enclosure. Follow the sheet exactly; the system

was programmed at the factory to operate only as indicated on the sheet.

Note: Before connecting all signal cables, attach only the first two

inputs and outputs from the "AutoPatch 8Y-XL Connector and

Groupings Guide," and then perform a test switch to verify that the

system is working properly. See Chapter 7 for details on performing a

test switch.

To attach video inputs and outputs, slide the video cable onto the input

or output connector (see graphic below).

Inputs and Outputs

Make sure video signals are attached to video connectors and sync

signals are attached to sync connectors. The connectors look identical,

but the “Connector and Groupings Guide” identifies them.

3536

Attach a video cable to a BNC connector

4-2 Installation and Setup Guide

Attaching Input and Output Cables

To attach audio inputs and outputs, unscrew the clamps on the audio

connector, insert the proper wire, and re-tighten the clamps so they hold

the wire tightly and make proper connections. The graphic below shows

balanced audio connections, and the graphic on the next page shows

unbalanced audio connections.

Input

INPUT

+GND -

Signal Direction

Output

OUTPUT

+GND -

Signal Direction

Balanced audio connections

Note: For audio signals using twisted pair wire, connect the shield only

at one end to minimize low frequency noise.

Inputs and Outputs

Installation and Setup Guide 4-3

Attaching Inputs and Outputs

INPUT

OUTPUT

+GND -

Signal Direction

Input

Output

Inputs and Outputs

Signal Direction

Unbalanced audio connections

4-4 Installation and Setup Guide

Paralleling Inputs

4.2 Paralleling Inputs

Caution: Make sure the matrix’s configuration file reflects any changes

made to the I/O connectors of an enclosure. To parallel inputs, the matrix

must be equipped with high impedance I/O boards.

Each enclosure in an 8Y-XL is its own switching environment, so the

inputs of one enclosure cannot be switched to the outputs of another.

However, by paralleling inputs between multiple enclosures, a signal can

be routed on all of the enclosures where it is attached. Paralleling inputs

expands the matrix’s signal routing possibilities up to 64x256.

37393

75 W

655

17 18

25 26

3536

27 28

5758

960

Link Cable

37393

3536

15 16

COMM

STATUS

LINK 1

COMM

STATUS

LINK1

PORT2

PORT1

PORT2

PORT1

LINK 2

LINK2

25 26

17 18

25 26

27 28

15 16

59 6

3536

59 6

3536

59 6 0

5758

162

37393

8454

655

BNC Barrel Connector for splitting the signal

Inputs and Outputs

High Impedance

Split the input signal when paralleling inputs

Installation and Setup Guide 4-5

Attaching Inputs and Outputs

To parallel inputs, split an input signal between two or more input

connectors on different enclosures.

To minimize signal degradation when splitting a video input signal,

make sure the matrix is equipped with high impedance I/O boards. With

the exception of one board, all of the boards among which the signal is

split must be high impedance. For example, in the system pictured on the

previous page, the I/O board in the top enclosure should be 75W and the

board in the bottom enclosure should be high impedance. You can order

high impedance boards from AutoPatch.

Caution: Do not split an input signal between more than four connectors

without a line amplifier.

Inputs and Outputs

4-6 Installation and Setup Guide

Attaching an External Controller

The 8Y-XL can be controlled with external controllers using two types

of communication protocols:

Serial, BCS (Basic Control Structure) – serial ports

XNNet* – all ports (including serial)

Control systems and panels (such as SBCs* and remote control panels*)

usually connect to the X

usually connect to the serial connector. We recommend using the

Ethernet connector for linking enclosures.

*These controllers are not covered in this document.

Net connector. Third party controllers and PCs

External Control

Installation and Setup Guide 5-1

Attaching an External Controller

A serial controller is any device that can send and receive ASCII code

via RS232 or RS422. You can connect a serial controller to either of the

two serial connectors on an enclosure’s CPU board. Connect serial

controllers with either standard RS232or RS422 connections (refer to the

following graphics for RS232 and RS422 cable connector pin mappings).

AutoPatch: DB9

RXD

RTS

AutoPatch: DB9

TXD

CTS

GND

RS232 pin diagram

RXD

PC: DB9

TXD

DSR

RTS

PC: DB9

CTS

GND

DTR

GND #5...................................GND #5

RXD #2....................................TXD #3

TXD #3.....................................RXD #2

RTS #7.....................................CTS #8

CTS #8.....................................RTS #7

DSR #6......DTR #4

The pin diagram above allows for hardware flow control. If this type of

control is not needed, connect pin #7 to pin #8 on the PC’s connector.

RS232 pin diagram for a Macintosh computer

External Control

5-2 Installation and Setup Guide

Macintosh

AutoPatch: DB9

A&E..........................................5

D................................................3

F.................................................2

AutoPatch: DB9

PC: DB9

AutoPatch: DB9

Platform specific

RS422 pin diagram

RXD-

AutoPatch: DB9

GND #5 RXD+ #6 RXD- #1 TXD+ #4 TXD- #9

RXD+

TXD+

TXD-

GND

When controlling the system with a PC, use serial communication

software and make sure the BAUD rate is set correctly for the system.

Available BAUD rates for 8Y-XL systems are 9600, 19200, 38400 and

57600; the default is 9600.

Recommended settings (also default settings) for serial communication

with an 8Y-XL are:

BAUD 9600

Data Bits 8

Stop Bit 1

Parity NONE

Note: Make sure the settings on both the PC serial communication

software and the CP-10 Control Panel correspond to each other.

External Control

Installation and Setup Guide 5-3

Applying Power and the Startup Sequence

Your 8Y-XL ships with power cords that are compatible with your

country’s power sources. Always use an earth-grounded power

cord/system with this matrix switcher.

The system’s universal power supplies will accept all major,

international, standard power sources (see page B-1 for power supply

specifications).

Power & Startup

WE RECOMMEND ATTACHING ALL POWER CORDS TO A

SINGLE SURGE PROTECTOR AND/OR AN AC LINE

CONDITIONER.

Installation and Setup Guide 6-1

Power & Startup

Applying Power and the Startup Sequence

6.1 Applying Power

To apply power:

1. Plug each enclosure into a power source.

WE RECOMMEND SURGE PROTECTORS AND/OR AN AC

LINE CONDITIONER.

2. Press the “1” side of the power switch to turn it on.

6.2 Startup from the CP-10 Control Panel

After applying power and turning on the enclosure(s), the CP-10 Control

Panel displays the Command screen. The system is ready for a test

switch (see Chapter 7, "Executing a Test Switch").

6-2 Installation and Setup Guide

Startup from a Control Device

6.3 Startup from a Control Device

After applying power and turning on the enclosure(s), the splash screen

displays startup diagnostic information, followed by “Ready.” If you

need details regarding items on the screen or if errors are reported, call

AutoAssist (see Technical Support, page v). A sample splash screen for

an 8Y-XL is shown below. The system is ready for a test switch (see

Chapter 7, "Executing a Test Switch").

AutoPatch Modula signal router booting on Fri Jan 01 00:00:00 2001

AutoPatch 8YXLa signal router

Host software version 2.1.6

Host software: v2.2.1

Appcode version 1.2.2 D

Appcode: v1.3.2 R Hardware driver: v0.0.3 R

Hardware driver version 0.1.5 D

Built on Aug 09 2001 12:03:54

Built on May 07 2001 15:17:57

System PLD: A6

System PLD version A6

XNet address: 0x43b.

System startups: 20, cumulative service hours: 257.0, total switches: 1581.

No errors reported

XNet address: 0x04ab. NVRAM settings: warm reboot. User preferences reset to last valid state.

Ready

Assuming 48x16 I/O configuration. 48x16 Video UWB switch board detected at 0x80800000 IO slots:VI:VI:VI:VI:VI:VI:VI:VI:VI:VI:VI:VI:VO:VO:VO:VO Interface 1: BCS mode RS232 port, 9600 (8/1/N) Interface 2: BCS mode RS232 port, 9600 (8/1/N) Interface 3: 10Base2 BNC Ethernet Interface 4: Neuron bridge version 1.0.2 Virtual matrix status: valid. Virtual matrix count: 1

--------------------------------------- 'default'(0), 48x16x1,

---------------------------------------

Ready

Power & Startup

Startup information in HyperTerminal

Installation and Setup Guide 6-3

Executing a Test Switch

Execute a test switch to verify the system is working properly before

attaching all inputs and outputs. Aside from having signal cables

attached, the system is ready to perform switches when it ships from the

factory.

You can execute a test switch from the following:

CP-10 Control Panel

An external serial controller (computer, AMX, Crestron, etc.)

via BCS (Basic Control Structure) commands

Note: Before executing a test switch, attach only the first two inputs and

outputs described in the AutoPatch “8Y-XL Connector and Groupings

Guide” that came with your system.

The CP-10 test switch example (see page 7-2) routes input 2 to output 1

on Level 0 (your system may have been programmed with a different

level). The BCS Command test switch (see page 7-4) routes input 1 to

output 2 on Level 0. Before executing these switches, make sure the first

two inputs and outputs are connected exactly as shown on the AutoPatch

“8Y-XL Connector and Groupings Guide.”

Test Switch

Installation and Setup Guide 7-1

Test Switch

Executing a Test Switch

7.1 Executing a Test Switch Using the CP-10 Control Panel

The following test switch routes Input 2 to Output 1 on Level 0. Before

executing these switches, make sure the first two inputs and outputs are

connected exactly as shown on the AutoPatch “8Y-XL Connector and

Groupings Guide.”

To execute a test switch using the CP-10 Control Panel:

1. At the Command screen, press the Change key.

The Change screen appears.

2. Press the Level key and enter “0” (your system may have been

programmed with a different level).

3. Press the Input key and enter “2.”

7-2 Installation and Setup Guide

4. Press the Output key and enter “1.”

Using the CP-10 Control Panel

5. Press Take key.

The signal is routed and the Command screen appears.

If the switch did not execute properly:

Check all power switches to make sure the source and destination

devices are turned on.

Check all link and signal connections on the rear of the enclosure(s)

to make sure everything is physically set up correctly.

Attempt the switch again.

Test Switch

If the switch still does not work, call AutoAssist (see Technical Support,

page v).

Installation and Setup Guide 7-3

Executing a Test Switch

7.2 Executing a Test Switch Using BCS Commands

The following test switch routes Input 1 to Output 2 on Level 0. Before

executing these switches, make sure the first two inputs and outputs are

connected exactly as shown in the AutoPatch “Modula Connector and

Groupings Guide.”

To execute a test switch, enter the following BCS command line into a

serial terminal program attached to the matrix:

CL0I1O2T

Test Switch

For a complete list of BCS commands, see Appendix C in the back of

this guide.

If the switch did not execute properly:

Check all power switches to make sure the source and destination

devices are turned on.

Check all link and signal connections on the rear of the enclosure(s)

to make sure everything is physically set up properly.

Attempt the switch again.

If the switch still does not work, call AutoAssist (see Technical Support,

page v).

7-4 Installation and Setup Guide

Managing Configuration Files

A configuration file is a text file that contains system configuration

information that has been previously downloaded to the CPU in your

matrix switcher before shipment. Each enclosure’s CPU references this

information during any type of switching operation. Unless you need to

modify your system, you will not need to use any of the software set that

is included in shipping. A copy of the configuration file is in the

\MyXCL folder on the AutoPatch Configuration Software Disk 1 inside

the cover of the User’s Operation Manual.

Configuration Files

Installing the AutoPatch Configuration Software set uploads X

a graphical software program that can be used to modify and download

configuration information.

If you lose any of your AutoPatch software, contact AutoAssist (see

Technical Support, page v) to replace it. Make sure that you have your

system’s serial number ready when you call.

To modify a configuration file using X

about the following topics, which are covered in this chapter:

Conceptual overview

Installing and launching

Panes, views, and dialog boxes

Opening and downloading a configuration file

Modifying a configuration file

Connect, you need information

Connect,

Installation and Setup Guide 8-1

Managing Configuration Files

8.1 Conceptual Overview

The physical component(s) of a system can be a standalone matrix

switcher or multiple matrix switchers with or without additional

controllers. Opening a copy of the system’s configuration (.xcl) file

directly to X

Connect’s four basic functions:

XNConnect graphically displays the content of the AutoPatch

configuration file. This information is represented in two main

views, the “Hardware” view and the “Virtual Matrices” view.

The representations can be modified to reflect desired physical

changes to the system.

When replacement or new components are added to the system, their

configurable properties can be set to the desired values.

The new configuration information can then be downloaded to the

system’s CPU(s).

Connect Configuration software allows you to use

Configuration Files

8.2 Installing and Launching

XNConnect is a graphical software program that displays your most

recent configuration and allows easy addition of local presets and

modification of other configuration information (see the X

file for assistance). X

Connect can also download the modified file to

the system.

Note: Use this software only if you need to change the configuration

information from the original specification.

To install X

Connect:

1. Close all other applications currently running on your PC.

2. Insert the AutoPatch Configuration Software Disk 1 into your floppy

drive.

3. From the Start menu in Windows, select Run.

4. Type in A:\setup.exe (or the letter for whichever floppy drive you are

using) and click OK.

Connect Help

5. Follow the directions in the subsequent dialogs in the install

program.

8-2 Installation and Setup Guide

Panes, Views, and Dialog Boxes

6. Review the Readme.txt file found on either Disk 1 or after

installation in the default install location C:\AutoPtch\Connect\.

To launch X

Connect:

1. From the Start menu, select Programs.

2. Select AutoPatch Applications (or any other file group you selected

during the install).

3. Select the Connect file group.

4. Select the Connect program.

The X

Connect program opens.

Configuration Files

8.3 Panes, Views, and Dialog Boxes

XNConnect displays two panes. The graphics are located in the left pane

and the properties of the currently selected graphic are in the right pane.

At the top of the left pane, you can access the different graphical

representation views from two tabs: Hardware and Virtual Matrices.

Hardware, such as enclosures and control panels, appear in the Hardware

view and existing virtual matrices appear in the Virtual Matrices view.

As you switch from view to view, the properties displayed in the right

pane automatically change to correspond to the new graphics.

Installation and Setup Guide 8-3

Managing Configuration Files

A variety of dialog boxes for modifying your system’s configuration file

are accessed through the main menu. The menu commands include

topics such as Modifying Serial Port Settings, Set Password Combo,

Managing Boards, Managing Virtual Matrices, and Managing Presets.

Note: If you have questions regarding a dialog box you have open,

Connect provides a context-sensitive Help file that can be accessed by

pressing the F1 key.

8.4 Opening and Downloading a Configuration File

Start the process of modifying your configuration file by opening it in

Connect. After modifications to the file are completed, XNConnect

can then download the new configuration information to your system.

To open a configuration file in X

Connect:

Configuration Files

1. From the Getting Started dialog box, click Open Configuration File.

2. Using the standard File Open dialog box, locate and open the XCL

(*.xcl) Input file for your system.

3. Using the Save As option, make a duplicate copy of your file with a

new name.

(Make a new duplicate copy every time you modify the file.)

4. Enter the desired modifications (see section 8.5) to the file copy.

To download the modified configuration file from X

Connect to

your system, from the Network menu, select Download Configuration.

Note: Depending on the modification, downloading the new

configuration information to your system may or may not be done while

the matrix switcher is operating.

8-4 Installation and Setup Guide

Modifying Configuration Files

8.5 Modifying Configuration Files

Modifying a configuration file with XNConnect involves entering

information in one or a series (depending on the modification) of dialog

boxes. A brief look at the Help file Contents provides an overview of the

modifications possible with X

Note: If you have questions regarding a dialog box you have open,

Connect provides a context-sensitive Help file that can be accessed by

pressing the F1 key.

When modifying a configuration file, it is helpful to keep in mind the

following definition of a virtual matrix. A virtual matrix is a set of virtual

source (input) channels and destination (output) channels in which the

channels’ component signals (such as R, G, B, H, and V) are grouped

into a single channel to permit the simultaneous switching of them as an

aggregate signal (RGBHV). Each component signal must have all

sources and destinations within the same physical matrix. The resulting

single channel constitutes a source or destination number on the Local

Control Panel.

Connect.

Configuration Files

The remainder of this section focuses on two of the most common uses

for X

Connect, configuring local presets and modifying groupings (see

the X

Connect Help file for assistance with other configuration related

tasks).

Configuring Local Presets

The process for configuring local presets takes you through three dialog

boxes. Start with the Manage Local Presets dialog box to access other

dialog boxes that allow you to name a new preset, modify presets, and

delete presets.

Installation and Setup Guide 8-5

Managing Configuration Files

The Name New Preset dialog box allows you to start the process of

creating a preset by giving it a name.

To name a new preset (in preparation for specifying preset

information):

1. In the Virtual Matrices view, select the targeted virtual matrix, and

from the Edit menu, select Manage Local Presets.

Configuration Files

2. Click the Name New button.

The Name New Preset dialog box appears.

3. Enter a name (limited to eight characters) for the new preset.

(This step is required in order to create a new preset.)

4. Enter a description. (This step is optional.)

5. Click OK to add the newly named preset to the Existing Presets list

in the Manage Local Presets dialog box.

6. Proceed to the next set of steps for modifying a preset in order to

specify information for the newly named preset.

The Modify Preset button opens the Modify Preset dialog box where you

can enter specific information for the new preset.

8-6 Installation and Setup Guide

Configuring Local Presets

To modify presets:

1. In the Manage Local Presets dialog box, click the Modify Preset

button.

The Modify Preset dialog box opens.

2. Select any of the following field or button options.

3. When done, click OK to return to the Manage Local Presets dialog

box.

Name (modify preset name) by typing a new name (eight character

limit) in the Name edit field that is not an existing preset name.

Assign Switch by selecting one available source channel and one or

more available destination channels (multiple select by holding

down the control key).

Click the Assign Switch button.

The assignment will appear in the Assignment column of the

Destination Channels list.

Configuration Files

Clear Source by selecting a source channel that you want to clear.

Click the Clear Source button.

All instances of the selected source will be cleared from the

Assignment column of the Destination Channels list.

Clear Destination by selecting a destination channel(s) (multiple

select by holding down the control key) that you want to clear.

Click the Clear Destination button.

The Source Channel(s) assigned to the destination(s) will be cleared

from the Assignment column in the Destination Channels list.

Disconnect by selecting either a source channel or one or more

destination channels to be disconnected.

Click the Disconnect button.

Current source and destination disconnects are displayed in the

Disconnected Channels list on their respective sides of the Modify

Preset dialog box.

Caution: Disconnecting an input affects all outputs that the input is

connected to whether they are part of this preset or not.

Note: During a source disconnect, all previous assignments for that

source are cleared from the Assignment column of the Destination

Channels list.

Installation and Setup Guide 8-7

Managing Configuration Files

Reconnect either a source or destination channel that has been

disconnected by selecting it.

Click the Reconnect button.

The channel is now available again for assignments.

Note: Reconnecting does not re-establish previous presets.

To delete an existing preset:

1. In the Virtual Matrices view, go to the Edit menu and select Manage

Local Presets.

2. Select the preset from the Existing Preset list that you want to delete.

3. Click the Delete Preset button. A message appears asking if you are

sure you want to delete the preset.

Configuration Files

4. Click OK to delete the preset and return to the Manage Local Presets

dialog box.

Note: Presets are not implemented until the modified configuration file

is downloaded (see Section 8.4) to the system.

Modifying Groupings

The process for modifying groupings takes you through two dialog boxes

that allow you to assign connectors individually to a single channel’s

signals or to a group of channels by pattern.

Manage Virtual Matrix Groupings

Use the Manage Virtual Matrix dialog box as a central point from which

to assign signals to connectors, thereby creating virtual source and

destination channels (sets of signals that will switch together because

they have been grouped together). Even though you must click the

Accept Groupings button to accept the new groupings, they are not

implemented until the modified configuration file is downloaded (see

Section 8.4) to the system.

8-8 Installation and Setup Guide

Modifying Groupings

Configuration Files

To specify connector groupings from the Virtual Matrix view:

1. From the Edit menu, choose Manage Virtual Matrix Groupings.

The Manage Virtual Matrix Groupings dialog box appears.

2. Click the Group by Pattern button to assign sequential or spanning

groupings of signals for connectors (see page 8-10).

Click the Assign Individually button to assign signals to connectors

one at a time (see page 8-11).

After entering information in the newly opened window and clicking

OK, the Manage Virtual Matrix Groupings dialog box will reappear

with the results displayed in the read-only box at the bottom (see

graphic above). The tabs allow viewing of each channel of grouped

signals for both sources and destinations.

3. Repeat as needed, using either method to assign additional

groupings.

Note: At any time, click the Accept Groupings button (at the bottom of

the box) to save the groupings to the virtual matrix or click the Cancel

button to start over. Remember, however, that the new groupings are not

implemented until the modified configuration file is downloaded (see

Section 8.4) to the system.

Installation and Setup Guide 8-9

Managing Configuration Files

Group Connectors by Pattern

The Group Connectors by Pattern dialog box allows you to group signals

with connectors in either a spanning or sequential pattern, thereby

creating a large number of virtual source and destination channels

simultaneously. Choose the spanning pattern to create groupings with

blocks of similar signal types; for example, plug all the red in RGB into

adjacent connectors on the matrix. Choose the sequential pattern to

define groupings where each aggregate signal is plugged in next to each

other in the matrix.

Configuration Files

Note: This dialog box can only be accessed from the Manage Virtual

Matrix Groupings dialog box; select it from the Edit menu after selecting

the target virtual matrix.

To specify details about the pattern:

1. Choose the pattern type by clicking either the Spanning or Sequential

button.

2. Choose the channel type by clicking either the Sources Only or

Destinations Only button.

The destinations can mirror the sources by clicking the Mirror

Directions check box.

8-10 Installation and Setup Guide

Modifying Groupings

3. In the Starting Channel box, choose the starting channel number that

you want if it is different from the next available channel that is

already displayed.

4. Enter the number of channels you want to create in the Number of

Channels to Create box.

You are now ready to group signals to create virtual channels.

To create signal groupings:

5. From the Available Signals list box, choose a signal.

6. From the Enclosure list box in the middle of the dialog box, choose

the enclosure in which you want the selected signal routed.

7. From the Matrix list box, select the physical matrix in the enclosure

on which this signal will be switched.

8. From the Available Connectors list box, choose the starting

connector. Click the Assign Signal button.

The added signal appears in the Signals with Connector Groupings

box.

To remove a signal, highlight it, and then click the Remove

Signal/Connector button.

Configuration Files

9. Continue assigning connectors until all the signals show up in the

Signals with Connector Groupings box.

10. Click OK to enter the signal groupings and return to the

Manage Virtual Matrix Groupings dialog box.

Note: You must click the Accept Assignments button at the bottom of

the Manage Virtual Matrix Groupings dialog box in order for your

signals to be grouped into virtual channels. Remember, however, that the

new groupings are not implemented until the modified configuration file

is downloaded (see Section 8.4) to the system.

Assign Connectors Individually

The Assign Connectors Individually dialog box is used to modify the

connector assignments in a virtual matrix. Each channel of a virtual

matrix has a specific number of signals, and each signal has a

corresponding connector assignment. For each signal in a specific

channel, you may add or remove a connector assignment.

Installation and Setup Guide 8-11

Managing Configuration Files

Configuration Files

To access the Assign Connectors Individually dialog box:

1. In the Virtual Matrix View, right click the virtual matrix for which

you want to make connector assignments.

2. Select Manage Connector Groupings.

The Manage Virtual Matrix Groupings dialog box appears.

3. From the Select a Method section of the dialog box, click the

Assign Individually button.

The Assign Connectors Individually dialog box appears.

To assign connectors individually:

4. From the Current Channel list, select the channel where you want to

make connector assignments. If no channels are available, click the

Create New Channel button.

5. From the Select Channel Type section of the dialog box, click either

Source (input channels) or Destination (output channels).

6. Highlight the signal you wish to add in the Available Signals list.

7. From the Enclosure list box in the middle of the dialog box, choose

the enclosure in which you want to create the groupings.

8. From the Matrix list box, select the physical matrix on which this

signal will be switched.

8-12 Installation and Setup Guide

Modifying Groupings

9. From the Connector list, select the connector you want to assign a

signal to and click the Assign Connector button.

The signal and its connector appear in the Signals with Connector

Assignments list.

10. Continue to make assignments until all signals in all channels have

been given connector assignments. This ensures that the virtual

matrix will be valid.

11. Click OK to enter the connector assignments and return to the

Manage Virtual Matrix Groupings dialog box (connectors are

entered but not accepted; see the following Note).

Note: You must click the Accept Assignments button at the bottom of

the Manage Virtual Matrix Groupings dialog box in order for your

connector assignments to be accepted. Remember, however, that the new

groupings are not implemented until the modified configuration file is

downloaded (see Section 8.4) to the system.

Configuration Files

Any highlighted signal and connector can be removed by clicking the

Remove Connector button. The Clear All Sources button removes all

connector assignments for all channels of the currently selected channel

type (sources or destinations). This is useful for removing all connectors

and starting fresh with no assignments

Installation and Setup Guide 8-13

Adjusting Gain

Gain is the ratio of a signal’s output level to input level and is usually

measured in decibels (dB). Adjust gain to equalize signal levels so you

have the same output level on all signals, no matter what their initial

input levels are.

Gain control on audio and video output signals is standard in the 8Y-XL.

However, you can also order audio and video input boards with gain

control.

At the factory, inputs and outputs are set to unity gain (overall gain of 1

dB). An extender board that makes the gain adjustment pots accessible

and a gain adjustment tool are shipped with the 8Y-XL in the master

enclosure’s shipping box.

When adjusting gain, you will work with switching boards, daughter

boards, and an extender board. The switching board links the daughter

board to the main components of the matrix, and the daughter board

holds signal connectors and gain adjustment pots. The main function of

the extender board is linking the daughter board to the switching board

while you adjust gain. During normal operation the daughter board is

attached to the switching board and the extender board is in storage.

Adjusting Gain

Installation and Setup Guide 9-1

Adjusting Gain

Each signal’s gain adjustment pot is directly behind the signal’s

connector on the daughter board and is labeled TR#.

The extender board fits both input and output board sets; however, input

and output board sets fit together conversely so you must flip the

extender board to fit each set. To adjust gain on an output board, attach

the extender board’s male connector to the switching board; for an input

board set, attach the female connector to the switching board (see graphic

below).

Immediately after adjusting signal gain, remove the extender board. Do

not continue normal operation of the 8Y-XL with the extender board in

place.

37393

655

910

25 26

3536

15 16

27 28

960

5758

Adjusting Gain

3536

910

1495

COMM

STATUS

LINK 1

PORT2

PORT1

LINK 2

25 26

655

Turn horizontally 180º for input board interface

59 6 0

162

9-2 Installation and Setup Guide

Warning: To avoid ESD (Electrostatic Discharge) damage to sensitive

OUTPUT

components, make sure you are properly grounded (see the Caution page

inside front cover) before handling any internal 8Y-XL materials.

To adjust the gain:

1. Turn the enclosure off.

2. Remove the I/O daughter board from the enclosure.

3. Attach the extender board between the switching board and the

daughter board.

4. Reapply power. The 8Y-XL should be in proper working order.

5. While monitoring the input or output signal(s), adjust the signal gain

as necessary by placing the tip of the gain adjustment tool in the gain

adjustment pot (TR#) and turning the tool clockwise or

counterclockwise (see graphic below).

Adjusting Gain

Types of gain adjustment pots

Installation and Setup Guide 9-3

Adjusting Gain

OUTPUT

6. Remove the extender board alone by pushing down on the daughter

board side of the extender board arm while pulling the board out (see

graphic below).

Adjusting Gain

Note: Only use the extender board while adjusting the gain. Do not

continue using the extender board during normal operation.

7. Return the enclosure to its original state.

If you need to remove the switching board, remove the extender board

and the switching board together by pulling up on the daughter board

side of the extender board arm while pulling the boards out (see graphic

below).

9-4 Installation and Setup Guide

Adding Hardware

You can add input and output boards, vertical interval timing (sync)

boards, and enclosures to expand your system’s capabilities. Input and

output boards increase an enclosure’s possible signal routings. A vertical

interval sync board synchronizes video signal switches with the output

device’s refresh rate. Adding enclosures increases the entire system’s

switching capabilities.

When you add hardware to an 8Y-XL, you must update the system’s

configuration information by downloading a new configuration file. A

new configuration file, link cables, and other system products are

provided with the new hardware.

This chapter covers:

Adding Boards

Adding Enclosures

Hardware

Installation and Setup Guide 10-1

Adding Hardware

10.1 Adding Boards

Input and Output Boards

The number of input and output signals in an enclosure determines the

number of input and output boards. In an enclosure, signals are sent and

received through input or output connectors. Each board has eight

connectors.

To add an input or output board:

Warning: To avoid ESD (Electrostatic Discharge) damage to sensitive

components, make sure you are properly grounded (see the Caution page

inside front cover) before handling any internal 8Y-XL materials.

1. Turn off the enclosure.

2. Remove the plate that covers the empty expansion/control slot.

Make sure you are working with the correct slot. If you put the board

in the wrong slot, signal routing is affected. The board’s location

must match the system’s configuration information (uploaded from

the configuration file). A new configuration file is sent with new

boards.

Hardware

3. Attach the daughter board to the switching board.

17 18

27 28

25 26

19 20

COMM

STATUS

LINK1

PORT2

PORT1

LINK2

15 16

5758

37393

5758

37393

960

8454

655

3536

59 6

3536

10-2 Installation and Setup Guide

Adding Boards

4. Line up the board assembly (switching board and daughter board)

with the board guides that are on the left and right of the board slot

(see graphic on the previous page). Carefully push the assembly into

the enclosure until the switching board snaps into place.

5. Insert the screws into the holes on the connector assembly and

tighten the screws until they are snug.

6. Attach the signals to the appropriate connectors (see Chapter 4,

“Attaching Inputs and Outputs”).

7. Reapply power and turn on the enclosure.

Note: If you are adding an audio board and want to adjust the gain, see

Chapter 9, “Adjusting Gain.”

Vertical Interval Timing Board

A Vertical Interval Timing board (sync board) provides the 8Y-XL with

complete vertical interval synchronization switching capability. The sync

board can utilize a master sync signal by separating sync from an input

signal (such as a composite video input) or can be used with a blackburst

generator.

Each enclosure in an 8Y-XL can contain one sync board. You may want

a sync board in each enclosure that switches video signals. If the system

was originally ordered with sync boards, they are already installed in the

enclosures.

Hardware

Installation and Setup Guide 10-3

Adding Hardware

To add a sync board:

Warning: To avoid ESD (Electrostatic Discharge) damage to sensitive

components, make sure you are properly grounded (see the Caution page

inside front cover) before handling any internal 8Y-XL materials.

1. Make sure all enclosures receiving a sync board are turned off.

2. Remove the faceplate directly above the CPU.

3. Line up the sync board with the board guides on the left and right of

the top board slot. Make sure the connectors are on the upper side of

the board (see graphic below).

37393

8454

25 26

3536

15 16

27 28

59 60

758

Hardware

3536

910

COMM

STATUS

LINK1

PORT2

PORT1

17 18

LINK2

25 26

4950

5758

59 6 0

4. Carefully push the board all the way in, until it snaps into place.

5. Attach the new faceplate to the enclosure with screws.

6. Once you have added sync board(s), verify the system’s response by

reapplying power to all enclosures containing video in the system

and checking the splash screen.

7. Update the configuration file using X

Connect to enable the sync

board.

655

10-4 Installation and Setup Guide

Adding Enclosures

10.2 Adding Enclosures

You can expand the switching capabilities of an 8Y-XL by adding

enclosures. Whenever you add hardware to an 8Y-XL you must update

the system’s configuration information by uploading a new configuration

file. A new configuration file, link cables, and other system products are

provided with the new enclosure(s).

When attaching signals, follow the AutoPatch “8Y-XL Connector and

Groupings Guide” included with the new enclosure; all information

specific to the system is on or with that sheet.

To add an enclosure:

Warning: To avoid ESD (Electrostatic Discharge) damage to sensitive

components, make sure you are properly grounded (see the Caution page

inside front cover) before handling any internal 8Y-XL materials.

1. Although it is not necessary to turn all the enclosures in the system

off, we suggest doing so unless current operations will be disturbed.

2. Link the new enclosure to the other enclosures. See Chapter 3,

“Linking Enclosures,” for more information about linking enclosures.

3. Following the new AutoPatch 8Y-XL Connector and Groupings

Guide, attach all inputs and outputs. See Chapter 4, “Attaching Inputs

and Outputs” for more information about attaching inputs and

outputs.

4. Turn on all the enclosures in the system. The 8Y-XL goes through its

startup sequence.

Hardware

Installation and Setup Guide 10-5

AutoPatch Service and Returns Policy

A.1 Service

The AutoPatch 8Y-XL is to be serviced only by AutoPatch authorized

service agents.

Return Authorizations

Except for warranty claims, merchandise will not be accepted for return

or exchange after the first thirty (30) days following the invoice date.

Returned items must be shipped prepaid and insured in their original

packing containers (if possible). When returning merchandise, clearly

show the Return Materials Authorization (RMA) number on the outside

of each carton. Merchandise will not be accepted for any reason without

an RMA number.

Products and parts returned or exchanged for any reason other than

warranty purposes are subject to a restocking fee not greater than twenty

percent (20%) of the invoiced price, if returned in unused condition.

Claims for Shipping Damages

Unless otherwise specified, merchandise is normally shipped by Federal

Express Economy service; however, AutoPatch reserves the right to

select the final method and carrier for any shipment.

Although we take special care to ensure the safe arrival of all orders,

shipping accidents and damage can occur. Shipments are transferred to

the appointed carrier in good condition, and AutoPatch’s liability for the

product ceases when the transfer to the carrier is complete. Therefore,

claims for damages and shortages must be filed with the transporting

company by the receiving company within fifteen (15) days of receipt.

Installation and Setup Guide A-1

Policies

AutoPatch Service and Returns Policy

Visible damage and shortages must be noted on the freight bill;

packaging and contents must be retained for inspection.

A.2 Replacement Policies and

Procedures

During the warranty period:

1. Describe the problem to an AutoPatch dealer, regional

representative, or the AutoPatch customer service department.

2. Upon verification of a problem that requires factory repairs, an

AutoPatch customer service representative will issue a Return

Materials Authorization (RMA) number, and we will, at no cost,

repair or replace the part(s) returned to the factory and return the

part(s) to the sending party. If conditions do not permit this

procedure, we will invoice new or reconditioned (at AutoPatch’s

option) replacement part(s) to the dealer and ship the part(s) to the

dealer or to the consumer if so directed by written order from the

dealer. Unless otherwise instructed in writing by an AutoPatch

customer service representative, part(s) replaced under this warranty

must be returned to the factory:

Policies

a) within thirty (30) days;

b) with shipping and insurance costs prepaid;

c) with the RMA number clearly indicated on the outside of each

container;

d) in the original shipping container(s), if possible;

e) with a written description of problem.

If the replaced part(s) are returned within thirty (30) days, we will

apply credit to the dealer’s account for the total value of part(s)

determined defective, plus return shipping costs. Any part(s)

received after thirty (30) days or otherwise not in compliance with

these requirements may be refused, and credit will not be issued.

3. Repaired or replaced part(s) will be warranted for the remainder of

the original system warranty period for the first thirty (30) days

following the invoice date, or we will extend the original warranty

period by the period of verifiable downtime, whichever provides the

greatest benefit.

A-2 Installation and Setup Guide

Special Notice

Following warranty expiration:

1. Call your AutoPatch dealer, area representative, or the AutoPatch

customer service department with a description of the problem.

2. Upon verification of a problem that requires factory repairs, an

AutoPatch customer service representative will issue a Return

Materials Authorization (RMA) number. We will, at nominal cost,

invoice the sending party, repair or replace the part(s) returned to the

factory and return those part(s) to the sending party. If conditions do

not permit this procedure, we will invoice and ship new or

reconditioned (at AutoPatch’s option) replacement part(s) to the

dealer or to the consumer if so directed by written order from the

dealer.

3. Post warranty repairs and replacements are warranted for the first

thirty (30) days following invoice date.

A.3 Special Notice

AutoPatch reserves the right to modify or discontinue designs,

specifications, warranties, and policies without notice. All data with

regard to model numbers series, specifications, and prices in our

literature have been thoroughly reviewed and edited. Although we cannot

assume responsibility for inadvertent omissions or errors, we sincerely

apologize if misunderstandings occur, and we appreciate your criticism,

corrections, and suggestions.

Policies

Installation and Setup Guide A-3

Product Specifications

The following pages contain performance specifications for your

AutoPatch 8Y-XL Distribution Matrix. The AutoPatch web site

(www.autopatch.com) also has a full list of specifications for all

AutoPatch products.

B.1 General

AC Power 100 - 240 V single phase

Product Specs

Frequency 47 - 63 Hz

Humidity 0 to 90% non-condensing

13.5 in. (34.29 cm) depth

Dimensions

Weight Approximately 17 lb. (7.73 kg)

Fuse 2 Amp time lag (5 x 20 mm)

17.5 in. (44.5 cm) width without mounting ears

19.0 in. (48.26 cm) width with mounting ears

10.37 in. (26.34 cm) or 6 RU height

Installation and Setup Guide B-1

Product Specifications

B.2 Analog Audio

Standard Audio Boards

Throughput

Product Specs

Parameter Conditions Value

Frequency Response (20 Hz to 20 kHz) <ñ0.1 dB

Gain Flatness

THD + Noise

Signal to Noise Ratio

(S/N)

Adjacent Crosstalk

Power Supply

Rejection Ratio

(20 Hz to 20 kHz)

(20 Hz to 100 kHz)

Vin=3.3 dBu to 13.2 dBu

f=20 Hz to 20 kHz

Vin=13.2 dBu, 20 Hz to 20 kHz -103 dB

f=1 kHz, Vin=± 24 V

Vs=± 15 V

0.01 dB

0.1 dB

<.01%

<-95 dB

-80 dB (Typ)

-60 dB (Min)

Input

Parameter Conditions Value

Level (maximum)

Impedance

Type

Common Mode

Differential

19.4 dBu 4

36.1 dBu

18 kW

Balanced or

Unbalanced

CMRR

Gain Control Range Vin=3Vp-p -3 to +10 dB

Connector Type

VCM=± 10 V, 20 Hz to 20 kHz

-90 dB (Typ)

-70 dB (Min)

Pluggable 3 Position

Screw Terminal

Output

Parameter Conditions Value

Level (headroom)

Impedance

Type

Gain Control Range -3 to +10 dB

Connector Type

B-2 Installation and Setup Guide

± 28 dBu 50 W

Balanced or

Unbalanced

Pluggable 3 Position

Terminal Block

Analog Video

B.3 Analog Video

Standard Video Boards

Throughput

Parameter Conditions Value

Bandwidth (1 dB)

Bandwidth (3 dB)

Differential Gain f=3.58 MHz 0.1% or Better

Differential Phase f=3.58 MHz

Signal to Noise Ratio (S/N) Vin=+0.7 V -73 dB

Crosstalk (adjacent

channel)

Time Delay

Vin=± 1V Vin=± 1V

f=5 MHz <-60 dB

Vin=± 0.5 V square wave

Input

Parameter Conditions Value

Level (maximum)

12 MHz (1:ALL)

30 MHz (1:ALL)

0.1° or Better

<20 ns

± 5V

Product Specs

Impedance

Gain Control Range -3 to +10 dB

Connector Type BNC

75 W or Hi-Z (22 kW )

Output

Parameter Conditions Value

Level (maximum)

Impedance

Gain Control Range -3 to +10 dB

Connector Type BNC

± 5V 75 W

Installation and Setup Guide B-3

Product Specifications

Wideband Video Boards

Throughput

Parameter Conditions Value

Product Specs

Bandwidth (3 dB)

Signal to Noise Ratio (S/N) Vin=0.7 V (100% IRE) -70 dB

Crosstalk

(adjacent channel)

Time Delay

Vin=± 1V

f=5 MHz -60 dB

Vin=± 0.5 V square wave

250 MHz (1:ALL)

<20 ns

Input

Parameter Conditions Value

Level (maximum)

Impedance

Gain Control Range -3 to +10 dB

Connector Type BNC

± 2V 75 W or Hi-Z (22 kW )

Output

Parameter Conditions Value

Level (maximum)

Impedance

± 2V 75 W

Gain Control Range -3 to +10 dB

Connector Type BNC

B-4 Installation and Setup Guide

Analog Video

Ultra-wideband Video Boards

Throughput

Parameter Conditions Value

Bandwidth (3 dB)

Signal to Noise Ratio (S/N) Vin=0.7 V (100% IRE) <-70 dB

Crosstalk

(adjacent channel)

Time Delay

Vin=± 1V

f=5 MHz <-60 dB

Vin=± 0.5 V square wave

Input

Parameter Conditions Value

Level (maximum)

Impedance

Gain Control Range -3 to +10 dB

Connector Type BNC

Output

400 MHz (1:ALL)

<20 ns

± 2V 75 W or Hi-Z (22 kW )

Product Specs

Parameter Conditions Value

Level (maximum)

Impedance

Gain Control Range -3 to +10 dB

Connector Type BNC

± 2V 75 W

Installation and Setup Guide B-5

BCS (Basic Control Structure) Commands

BCS is a set of alphanumeric characters that allows a PC or other control

device to send commands to the system serially. When using a PC to

control the 8Y-XL, use serial software, such as Windows95

HyperTerminal, to establish communication. Command lines are not

case-sensitive.

The following table shows BCS command characters (keys), their

functions, and short descriptions of their functions.

Key Function Description

0"-"9"

" " Space

Change

Level

Number

Input

Output

Take

Exit

Status

Disconnect

Global Preset

Local Preset

Initiates an execute switch command

Flags the next1-3digit number as a level number

Identifies inputs, outputs, presets, and levels; combine the

digits to form larger numbers

Flags the next1-3digit number as an input specification

Flags the next1-3digit number as an output specification

Note: O is the letter O, not the number zero (0)

Separates numbers in multiple number entries

Executes a command

Exits, or cancels, the command being entered

Initiates verification of the status of input and output

connections

Initiates a disconnect switch command

Initiates an execute global preset or execute local preset

command

Note: Global presets are not implemented at this time

Flags the next1-3digit number as a local preset number

BCS Commands

Installation and Setup Guide C-1

Glossary

ASCII (American Standard Code for Information Exchange)

A code for representing alphanumeric information.

Backlight

The light that illuminates the LCD screen of the control panel on the

enclosure. Activate the backlight by pressing the Backlight key on the

control panel.

BAUD

The speed at which communications travel through the serial connector.

The 8Y-XL can send and receive communications at 9600, 19200,

38400, and 57600 BAUD.

BCS (Basic Control Structure)

A set of alphanumeric characters that combine to form command lines.

BCS command lines can be used to control a system from any serial

device that allows you to enter characters, such as a PC (personal

computer).

Command Line

A set of BCS command characters that constitute a command recognized

by the CPU.

Configuration File

A text file containing system configuration information referenced by

each enclosure’s CPU during any type of switch operation.

Installation and Setup Guide

Glossary

CP-10 Control Panel

An optional panel on the front of the enclosure with an LCD and keys for

entering commands. The CP-10 is designed for system control of the

8Y-XL Distribution Matrix.

CPU (Central Processing Unit)

Receives, interprets, and executes commands from the user through the

user interface (the CP-10 Control Panel or other control device).

Distribution Matrix

(see matrix switcher)

Enclosure

The metal chassis that holds input and output boards, a CPU board, and a

power supply. Each 8Y-XL enclosure can contain up to 8 input and 8

output boards, providing a total capacity of up to 64 input and 64 output

signal paths.

ESD (Electrostatic Discharge)

Electrical charges (such as static electricity) that can damage sensitive

components inside an enclosure. ESD damage could occur if you are not

properly grounded and not handling components correctly (see the

Caution page inside the front cover of this manual for more details about

ESD).

Expansion/Control Slots

Empty slots on the rear of an enclosure that will increase functionality

and add new features to your system.

External Controller

Any device that can control the matrix switcher via the serial connector.

Input and Output Connectors

Attachment points on the rear of an 8Y-XL enclosure for devices that

connect to the system. Input and output signal cables attach to the input

and output connectors. Standard 8Y-XL audio and data connectors are

3 position terminal block; video and sync connectors are BNC.

Installation and Setup Guide

Input Board

A circuit board that receives video, audio, or data signals from outside

sources.

LCD (Liquid Crystal Display)

The screen on the CP-10 Control Panel for user interaction.

Level

A level is a set of input and output signals that are grouped and,

therefore, switch together. In a configuration file, a level is referred to as

a “virtual matrix.”

Local Preset

A pre-defined set of signal routings that can be executed at any time.

Presets are defined in the configuration file.

Matrix Switcher

The hardware and software necessary to switch signals. Matrix switchers

are also known as routing switchers or routing matrices.

Output Board

A circuit board that routes input signals to specified destinations.

Output Connectors

(see Input and Output Connectors)

Power Supply

Contains a power switch, a power connector, the fuse drawer, and the

main power supply fan vent.

SBC (Single Bus Controller)

Devices for controlling the input to a specified output device. For more

information see the SBC documentation.

Serial Connector

A 9-pin female connector on the rear of an enclosure used to connect

serial external control devices connect to the matrix switcher.

Installation and Setup Guide

Glossary

Serial Controller

An external controller that communicates with the matrix switcher via a

serial cable.

Signal

A set of connectors whose signals switch together. A signal may contain

audio, video, data, or sync information.

Single Bus Controller

(see SBC)

Switch

An active connection between an input signal and one or more output

devices.

Virtual Matrix

A set of virtual inputs and outputs (or source and destination channels) in

which aggregate signals (such as RGBHV) are grouped into a single

channel to permit simultaneous switching of the component signals

(R, G, B, H, and V). Virtual matrices are also referred to as levels.

XNConnect

A graphical software program that displays your most recent

configuration and allows easy addition of local presets and modification

of other configuration information (see the X

assistance).

Net

An internal communication protocol that requires software driver support

for Ethernet and Neuron

interfaces.

Connect Help file for

Installation and Setup Guide

Index

AC line conditioner 1-7, 2-2, 6-1

AC power B-1

adding boards

see hardware, adding

adding enclosures

see hardware, adding

adjusting gain 9-1

illus. 9-3

applying power

see startup

arrow keys 1-3

audio

attaching 4-3

board specifications B-2

board, illus. 1-6

connectors iv

AutoAssist v

Backlight key, CP-10 1-5

Basic Control Structure

see BCS

BAUD rate settings 5-3

BCS (Basic Control Structure)

command characters (keys) C-1

definition iv

test switch 7-4

BNC barrel connector 4-5

boards

capacity ii

extender 9-2

high impedance 4-6

AutoPatch 8Y-XL, 8Y-3000 Installation And Setup Manual

Specifications and Main Features

Frequently Asked Questions

User Manual