INSTALLATION INSTRUCTIONS
DIESEL EXHAUST PRESSURE GAUGES
2650-1700-00
If after completely reading these instructions you have questions regarding the operation or installation of your instrument(s),
Installation
1. The 2
2. Follow the diagram below to connect 12 volt lighting.
1⁄16" gauges may be mounted in a 2
hole may be either a hole in the dash, a gauge panel or an Auto
Meter Gauge Pod. (It is best to connect all wiring to the gauge
before mounting it into the gauge hole.)
please contact Auto Meter Technical Service at 866-248-6357.
You may also email us at service@autometer.com.
Additional information can also be found at http://www.autometer.com
Power-Up
1⁄16" diameter hole. The
The pointer will move backward to the stop pin and then move to
the zero box. This procedure is an auto-calibration function and is
performed on every power-up. While this test is being performed,
the gauge may make a clicking sound. This is normal.
Exhaust Particle Trap Recommendation
To extend the maintenance period on the copper coil, Auto Meter recommends the installation of the Diesel Particle Trap kit, model #5375. The Diesel Particle
is inserted between the copper tubing and either the FSE pressure sensor or the nylon tubing used on the mechanical gauge. The trap provides an expansion
chamber for the soot particles to collect, similar to a dust collector. It also incorporates a z brass snubber to minimized pressure spikes at the pressure sensor or
mechanical gauge. It is easy to open for removing accumulated soot.
QUESTIONS:
Wiring
OPTIONAL
SLIT TUBING
RECOMMENDED
(AVAILABLE AT MOST
HARDWARE STORES)
+12v DASH
LIGHTING
GOOD
ENGINE
GROUND
WHITE
BLACK
(for standard incandescent
lit instrument)
CAUTION!
As a safety precaution, the
+12V terminal of this product
should be fused before
connecting to the 12V ignition
switch. We recommend using a
3 Amp, automotive type fuse.
GROMMET
FIREWALL
SENDER
WIRING
HARNESS
FOR INTERNAL LED
LIT INSTRUMENTS
WHITE
+12v DASH
LIGHTING
FUSE
(SEE CAUTION LEFT)
+12v CONNECTION
Mounting and Connecting Mechanical Gauges
CONNECT TO
12V LIGHTING
CONNECT TO
GOOD GROUND
COMPRESSION
1
4" NPT ADAPTER
FERRULE
OR
1
8" NPT ADAPTER
NUT
NYLON TUBING
GROMMET
FERRULE
1. Gauges may be mounted in In-dash holes, or in Auto Meter custom mounting
Solutions. Secure gauge with mounting clamps supplied. 2-
1
in 2-
⁄16" diameter hole.
3
2. Drill
⁄8" dia. holes and install rubber grommet where pressure line passes
through sheet metal, such as firewall.
3. Attach nylon pressure line to fitting on back of gauge using adapter, ferrule,
and compression nut as shown in diagram above. Route line through grommet
Connect the nylon line to the coiled copper tube attached to the exhaust
manifold using 1/8" connector.
SMALL
FERRULE
COMPRESSION
NUT
LOCK WASHER
THUMB NUT
OR
ADAPTER
MOUNTING
BRACKET
PORT NUT
USE TEFLON
SEALING COMPOUND
ON PIPE THREADS
1
⁄16" gauges mount
NOTE: DO NOT
LOOSEN PORT NUT
OR GAUGE MAY
BE DAMAGED.
NOTE: When the ignition
is off the pointer
RED
BLACK
12V BATTERY
may not always
rest at zero.
GOOD ENGINE GROUND
NOTE: DO NOT OVER TIGHTEN
ADAPTER FITTING OR
GAUGE MAY BE DAMAGED.
GROUND
+12 VOLT
LIGHTING
INTERNAL LED
LIGHTED MODELS
4. Make sure line is free from hazard of moving parts or hot engine components.
It is recommended that Auto Meter 3224 copper tubing kit be used where a
potential hazard exits.
5. Start engine and thoroughly check installation for leaks.
6. Twist in light socket assembly and connect one wire to dash lighting circuit or
other 12V power source and the other wire to a good ground.
Copper Coil Installation
When connecting to the exhaust manifold, it is necessary to prevent the extremely
hot gases from entering either the 1/8" nylon tubing (mechanical versions) or the
pressure transducer (FSE versions). To adequately cool these gasses, a 6 foot
length of coiled 1/4" copper tubing and the necessary fittings are provided. This
tubing is to be connected to the exhaust manifold collector.
Use the stainless steel 1/4" tube to 1/8" NPT fitting to make the connection at the
manifold. Drill into the cast iron manifold with a 5/16" letter R (0.339) drill bit and
follow through with a 1/8" NPT pipe tap. Mount the stainless steel to the exhaust
manifold (see fig. 1).
Carefully form the copper tubing (be careful not to kink the tubing) and connect one
end in the stainless steel fitting. The tubing should be formed to a shape that allows the
other end to be near a point to which it can be secured mechanically (i.e. with a strap,
bracket, etc.).
A. Mechanical Version:
Once the copper tubing has bee mounted, connect the 1/8" nylon tubing to
the copper tubing using the 1/4" tube to 1/4" NPTF fitting, the 1/4" to 1/8"
reducer, and the 1/8" fitting (see fig. #1). To prevent vibrations, secure the
copper/nylon tubing to something solid with strapping.
B. FSE Version:
Once the copper tubing has bee mounted, connect the Pressure Sender
to the copper tubing 1/4" tube to 1/4" NPTF fitting and the 1/4" to 1/8" reducer
(see fig. #2). To prevent vibrations, secure the pressure sender to something
solid with strapping, or fabricate a bracket as a mount
Drill & Tap into Manifold (D)
Drill 5⁄16” letter R (.339)
Hole and tap for 1⁄8” NPT
in cast exhaust manifold
collector or other engine
builder specified location.
Figure 1
Copper Coil Fitting #1 Copper Coil Fitting #2
Diesel Exhaust Considerations and Installation Maintenance
The pressure in the exhaust system is constantly varying in normal operating conditions. While there is not a “flow” of exhaust gases through the
copper tubing, the compression and expansion of the exhaust gases within the tubing will cause some migration of diesel exhaust particulates (soot) into
the tubing. Over time these particles may build up to a point that will interfere with proper operation of the gauge (both Mechanical and FSE versions).
For this reason, periodic maintenance of the copper tube is required. It is recommended the copper tube be monitored for build up. To check for build
of soot, loosen and remove the 1/4" tubing at the gauge end of the coil. If there is noticeable build, use an air hose to blow air through the coil back into
the exhaust manifold. Re-connect the copper tubing.
The frequency and need for the copper tube maintenance will vary. Factors affecting the build up are miles driven, type of driving, etc. If the engine is
considered a “smoker”, close monitoring and more frequent maintenance will be required.
The Ultimate LED Lighting Upgrade (for incandescent, non LED instruments)
Available through your local speed shop or favorite Auto meter dealer, these intense LED bulbs simply replace the standard 161, 168, 193, or 194 light bulbs used in most
Auto meter gauges, tachometers, and speedometers.
LED Replacement Kits are sold one per package.
3284 Red LED Replacement Kit
3285 Green LED Replacement Kit
3286 Blue LED Replacement Kit
For service send your product to Auto Meter in a well packed shipping carton. Please include a note explaining what the problem is along with your phone number. If you are sending product back for Warranty
adjustment, you must include a copy (or original) of your sales receipt from the place of purchase.
Auto Meter Products, Inc. warrants to the consumer that all Auto Meter High Performance products will be free from defects in material and workmanship for a period of twelve (12) months from date of the original
purchase. Products that fail within this 12 month warranty period will be repaired or replaced at Auto Meter’s option to the consumer, when it is determined by Auto Meter Products, Inc. that the product failed due
to defects in material or workmanship. This warranty is limited to the repair or replacement of parts in the Auto Meter instruments. In no event shall this warranty exceed the original purchase price of the Auto
Meter instruments nor shall Auto Meter Products, Inc. be responsible for special, incidental or consequential damages or costs incurred due to the failure of this product. Warranty claims to Auto Meter must be
transportation prepaid and accompanied with dated proof of purchase. This warranty applies only to the original purchaser of product and is non-transferable. All implied warranties shall be limited in duration to
the said 12 month warranty period. Breaking the instrument seal, improper use or installation, accident, water damage, abuse, unauthorized repairs or alterations voids this warranty. Auto Meter Products, Inc.
disclaims any liability for consequential damages due to breach of any written or implied warranty on all products manufactured by Auto Meter.
3287 Amber LED Replacement Kit
3288 White LED Replacement Kit
SERVICE
12 MONTH LIMITED WARRANTY
FOR SERVICE SEND TO: AUTO METER PRODUCTS, INC. 413 W. Elm St., Sycamore, IL 60178 USA (866) 248-6356
© 2013 Auto Meter Products, Inc.
Email us at service@autometer.com
http://www.autometer.com
The Super Bezel is a registered trademark of Auto Meter Products, Inc.
2650-1700-00 2/19/13
Loading...