ROLL UP GARAGE DOOR OPENER
OWNERS COPY
Warning: Failure to comply with the
Installation instructions and the
Safety warnings may result in
Serious Personal injury and/or
Property and Remote Control Opener damage.
Installation Instructions
PLEASE READ THESE IMPORTANT SAFETY RULES
Automatic Technology Australia Pty Ltd to the extent that such may be lawfully excluded hereby expressly disclaims all
conditions or warranties, statutory or otherwise which may be implied by laws as conditions or warranties of purchase of an
Automatic Technology Australia Pty Ltd Roll Up Garage Door Opener and Automatic Technology Australia Pty Ltd hereby
further expressly excludes all or any liability for any injury, damage, cost, expense or claim whatsoever suffered by any person as
a result whether directly or indirectly from failure to install the Automatic Technology Australia Roll Up Garage Door Opener in
accordance with these installation instructions.
2
For ADDITIONAL SAFETY protection we
STRONGLY recommend the fitting of a Photo Electric
Beam. In most countries Photo Electric Beams are
mandatory on all garage doors fitted with automatic
openers. For a small additional outlay ATA recommends
that Photo Electric Beams be installed with the
automatic opener insuring additional safety and peace of
mind.
DO NOT operate the garage door opener unless the
garage door is in full view and free from objects such as
cars and children/people. SERIOUS PERSONAL
INJURY and/or property damage can result from failure
to follow this warning.
DO NOT operate the garage door opener when
children/persons are near the door. Children must be
supervised near the garage door at all times when the
door opener is in use. SERIOUS PERSONAL
INJURY and/or property damage can result from failure
to follow this warning.
DO NOT allow children to operate the garage door
opener. SERIOUS PERSONAL INJURY and/or
property damage can result from failure to follow this
warning.
Make sure that the SAFETY OBSTRUCTION
FORCE is working correctly, and is TESTED and set
as per the Installation Instructions Manual. Failure to
follow the manual could result in SERIOUS
PERSONAL INJURY and/or property damage. This
test must be repeated at regular intervals and the
necessary adjustments made as required.
DO NOT disengage the door opener to manual
operation with children/persons or any other objects
including motor vehicle within the doorway.
Install the wall switch or wall mounted transmitter in a
LOCATION/POSITION where it is out of reach of
children and the garage door is visible.
Failure to comply with the following Safety Rules may result in
serious personal injury and/or property damage.
The unit should be installed so that it is protected from
the elements. It should not be exposed to water or rain.
It is not to be immersed in water or sprayed directly by
a hose or other water carrying device.
The garage door must be WELL BALANCED.
Sticking or binding doors must be repaired by a qualified garage door installer prior to opener installation.
DO NOT attempt to repair the door yourself as hardware is under extreme tension and can cause SERIOUS
PERSONAL INJURY and/or property damage.
REMOVE OR DISENGAGE all garage doors locks
and mechanisms prior to installation of the opener.
Connect the garage door opener to a properly
EARTHED general purpose 240V power outlet
installed by a qualified electrical contractor.
DISCONNECT THE POWER CORD from main
power before making any repairs or removing covers.
Only EXPERIENCED service personnel should
remove covers from the garage door opener.
Keep hands and loose clothing CLEAR of the door and
door opener at all times.
When using auto close mode a PHOTO ELECTRIC
BEAM must be fitted correctly and tested for operation
at regular intervals. EXTREME CAUTION is
recommended when using auto close mode. ALL
SAFETY RULES above must be followed.
In order for the garage door opener to SENSE an object
obstructing the door way, some FORCE must be
exerted on the object. As a result the object, door and/or
person may suffer DAMAGE or INJURY.
Make sure that the door is fully open before driving into
or out of the garage.
Make sure the door is fully closed before leaving the
driveway.
3
FEATURES
Your ATA Automatic Garage Door
Opener has many features which you
will appreciate. The components and
materials used in this Automatic Opener
are of the latest technology and highest
quality. Listed below are some of the
many features.
OPERATION
To operate the door simply press the
hand held transmitter or optional wall
switch for two seconds and the door
will automatically open or close. The
door can be stopped during an opening
or closing cycle by pressing again. The
next actuation will move the door in the
opposite direction.
HOPPING CODE
Every time a transmission is made from
the Remote Transmitter a new security
code is generated. The number of possible code combinations is over 4.29
billion. This greatly enhances security
of the system. Code “Grabbing” is
made a thing of the past.
ISS (INTELLIGENT SAFETY
OBSTRUCTION SYSTEM)
While the door is performing a close
cycle, should it hit an obstacle or be
restricted in some manner, it will
automatically reverse. The amount of
force the door should encounter before
reversing, is automatically adjusted by
the doors control system, during the
initial installation of the automatic door
opener. The door also if restricted whilst
opening will stop. The Safety
Obstruction Force should be checked at
least once a month. See installation
manual for instructions.
SECURITY CODE STORE
The Opener uses state of the art
technology in storing your selected
Transmitter Security Code. Up to 27
different codes can be stored in the
Openers memory.
To store a code simply press and hold
the Door Code button on the Opener
and press the Transmitter button twice.
Each or all codes can be deleted and
changed at any time. The codes can also
be stored with the Transmitter from a
remote location.
OVER LOAD INDICATOR
When the maximum opening and
closing capacity of the Opener is
exceeded the Courtesy Light will flash
10 times and an audible beeper will
sound to indicate that an Overload has
occurred.
SERVICE INDICATOR
The Opener has a Service indicator.
When the Overload LED light flashes
and the beeper sounds at the start of a
door cycle, it means that the opener and
or garage door needs a service.
AUTO COURTESY LIGHT
The Courtesy Light on the Opener
comes on automatically whenever the
door is activated to do an open or close
cycle. The Light can also be switched
on and off without operating the door.
This is done by pressing the button on
any Hand Held Transmitter which has
been stored with the light code, or by
pressing the light button on the Wall
Switch (optional). The light will stay on
for approximately three minutes then
switch off. This time is also adjustable.
CAS (COLOUR ASSISTED
SETTINGS)
To make the installation of the
Automatic Opener more user friendly
Automatic Technology Australia
developed the CAS (Colour Assisted
Settings) system. This unique system
makes installation easy and quick, as all
the Open and Close adjustments and
settings are colour coordinated. Red for
Close and Green for Open.
OPEN AND CLOSE DRIVE
BUTTONS
Another feature developed by
Automatic Technology Australia in
aiding in the installation of the opener is
the Open and Close Drive Buttons.
These buttons are used to help set the
open and close limit positions. A
quicker setting time and a more precise
limit position can be achieved using this
feature.
INITIALISATION
The Reset button on the Door Opener is
used to initialise or re-initialise the
obstruction settings and door travel
counts. See Installation Instructions for
further information.
AUTO CLOSE MODE
The Opener can be programmed to
automatically close after an open cycle.
The Auto Close time is adjustable. It is
compulsory to install a Photo Electric
Beam if this mode is selected, otherwise
the door will not operate.
SAFETY AUTO RUN TIME
If the Opener does not complete its
cycle within thirty seconds the Opener
will stop if opening, and reverse back
open if closing automatically.
PHOTO ELECTRIC BEAM
(OPTIONAL)
The Opener has an input for a Photo
Electric Beam to be connected for extra
safety protection. And/or use of the
Auto Close Mode.
MANUAL OPERATION
The Opener is equipped with a unique
Manual Disengaging Device. If the
power to the Opener is disrupted for any
reason the door can be put into Manual
Mode by pulling down on the string
handle, then releasing. This will allow
you to manually open or close the door.
When power is restored, by pulling
down on the string handle and
releasing, the opener is put back into
Automatic Mode.
4
OPERATING CONTROLS
1. LIGHT CODE button (White) is
used for storing or erasing the transmitter button (code) you wish to use to turn
the courtesy light on and off.
2. DOOR CODE button (Blue) is
used for storing or erasing the transmitter button (code) you wish to use to
command the door to open, stop or
close.
3. CLOSE DRIVE button (Red) is
used during installation to help set the
close limit stop position. Pressing and
holding this button will move the door
in the close direction. Movement stops
when the button is released.
NOTE: The close safety obstruction
detection is inoperable whenever the
Close Drive button is used to move
the door.
4. CLOSE LIMIT LED (Red) the
LED is very helpful during installation.
It illuminates and flashes when the door
is closing and remains steady on when
the close limit is activated
5. AUTO CLOSE TIME button
(White) is used to adjust the auto close
time. While holding in the Auto Close
button and then pressing the Open button the time is increased, pressing the
Close button will decrease the time.
(each press will increase the time by 5
seconds).
6. RESET button is used to initialise
and set the door/opener operating
parameters, including cycle times and
obstruction force settings. Check the
installation manual for other uses.
7. O/S/C button (Yellow) is used during installation to test the Open, Stop
and Close cycles for the Opener. The
Opener has to be initialised by the Reset
button before the O/S/C button becomes
operable.
8. CLOSE LIMIT ADJUST SCREW
(Red) is used to fine adjust the close
limit stop position. See installation
section on how to adjust.
9. OPEN LIMIT ADJUST SCREW
(Green) is used to fine adjust the open
limit stop position. Check installation
section on how to adjust.
10. CLOSE LIMIT CAM (Red) is
used to set the close limit stop position.
Check installation section on how to
adjust.
11. OPEN Drive button (Green) is
used during installation to help set the
open limit stop position. Pressing and
holding this button will move the door
in the open direction. Movement stops
when the button is released.
NOTE: The open obstruction
detection is disabled whenever the
Open Drive button is used to move
the door.
12. OPEN LIMIT LED (Green) the
LED is very helpful during installation.
It illuminates and flashes when the door
is opening and remains steady on when
the open limit is activated.
13. OPEN LIMIT CAM (Green) is
used to set the open limit stop position.
Check installation section on how to
adjust.
14. FORCE MARGIN SET button
(White) is used to change the force
pressure when the door encounters an
obstruction. Pressing the Force Margin
Set button and Open or Close button
will increase or decrease the force.
Normally the force pressure is set automatically. The Force Margin Set is only
ever used if other environmental factors
(wind, etc.) affect the operations of the
Door/Opener.
15. P.E. Input is for connection of
Photo Electric Beams (optional extra)
for extra safety obstruction protection,
are compulsory when used with Auto
Close mode.
NOTE: P.E. SHUNT must not be
removed otherwise the Opener will
not function correctly. Remove only
when a P.E. is to be connected.
16. EXTERNAL RECEIVER
INPUT is the input where an external
receiver can be connected (optional
extra). The receiver must be able to
operate on 24 volts DC (50mA max).
17. SECURALIGHT Input is used for
connecting a Securalight (optional
extra) Monitor. A Securalight is a
monitor unit which is mounted inside
your home and is connected to the
Opener by wire cable. The monitor
indicates the status of the door, for
example, if the door is moving or is
opened or closed, etc. The door can also
be controlled from the monitor unit.
18. O/S/C Input is for connecting the
wired Wall Switch (optional extra).
19. P. E. SHUNT The shunt has to be
removed when connecting a Photo
Electric Beam.
20. ENGAGE/DISENGAGE HANDLE when pulled down and released
will select manual mode on Opener
when there is a power failure. Pulling
down and releasing again will select
automatic mode on the Opener.
OPERATING CONTROLS
1) FORCE MARGIN SET BUTTON
2) OPEN LIMIT LED (GREEN)
3) OPEN DRIVE BUTTON (GREEN)
4) O/S/C BUTTON (YELLOW)
5) RESET BUTTON
6) AUTO CLOSE TIME BUTTON
7) CLOSE LIMIT LED (RED)
8) CLOSE DRIVE BUTTON (RED)
9) DOOR CODE BUTTON (BLUE)
10) LIGHT CODE BUTTON
11) ENGAGE / DISENGAGE HANDLE
12) OPEN LIMIT ADJUST SCREW (GREEN)
13) CLOSE LIMIT ADJUST SCREW (RED)
14) OPEN LIMIT CAM (GREEN)
15) CLOSE LIMIT CAM (RED)
5
PACKAGE CONTENTS
6
ITEM QUANTITY
(1) DRIVE UNIT………………………………………………………………………………………….. 1
(2) CONTROL BOX……………………………………………………………………………………... 1
(3) KEY RING TRANSMITTER PTX-4……………...………………………………………………... 2
(3.1) ALKALINE BATTERY A23 12V……………………………………………………………………. 2
(4) WEIGHT BARS (NOT INCLUDED IN SOME COUNTRIES)…………………………………...... 2
(5) WEIGHT BARS ACCESSORY PACK (NOT INCLUDED IN SOME COUNTRIES)……….......… 1
(5.1) PAN HEAD SCREW M5x40………………………………………………………………………….. 4
(5.2) HEX NUT M5………………………………………………………………………………………..... 4
(5.3) SPRING WASHER I.D 5……………………………………………………………………………… 4
(6) INSTALLATION MANUAL…………………………………………………………………………. 1
135mm
85mm
SEQUENCE OF INSTALLATION
7
SIDE ROOM REQUIREMENTS
Fig. 1 shows the minimum side room that is required. The
distance between the edge of the door curtain and the inside of
the bracket is 85mm, and the distance between the edge of the
door curtain and the outside of bracket is 135mm.
Fig. 2 shows the recommended side room. The distance
between the edge of the door curtain and the inside of the
bracket should be 110mm minimum, and the distance between
the edge of the door curtain and the outside of bracket is
160mm minimum.
1. CHECK OPERATION OF DOOR
BEFORE BEGINNING THE INSTALLATION OF THE
EASY ROLLER AUTOMATIC OPENER CHECK THE
OPERATION OF THE DOOR.
The door must be well balanced and be in a reasonable
operating condition. You should be able to lift the door
smoothly and with little resistance. It should stay open around
900mm to 1200mm above the floor. The door should not stick
or bind in the guide tracks. The ideal operational effort in
raising or lowering the door should not exceed a force of 10kg
(22 lbs.).
2. FIXING OF DOOR WEIGHT BARS
Move the door manually to the mid open position. Place the
weight bars equally apart on the bottom rail of the door and
secure them with the fasteners provided (Fig. 2A). Check the
operation of the door again. If the door feels heavy it may
require extra tension to be added to the door springs. Refer to
the door Installation manual from manufacturer on how to
tension the door.
FIG. 2A
FIG. 2
FIG. 1MINIMUM SIDE ROOM
RECOMMENDED SIDE ROOM
8
3. MOUNTING OF CONTROL BOX
1. Determine the position for the control box on the wall.
Considering that it must be: a) out of reach of children, 1.5 mtr
above the ground and b) close enough to the drive unit to run
the 1.8 mtr connecting wires.
2. If required, place the mains power and connecting wire
inside the slots on the back of the control box then into
appropriate conduit.
3. Drill all holes as shown in Fig. 3 and locate the bottom two
screws (not supplied) as shown leaving the screw head protruding 3.5mm (Fig 3a).
4. Mount the control box onto the bottom two screws.
5. Pull off the light diffuser and fix the top screw (not supplied)
through the control box, see (Fig 3). Replace the light diffuser.
4. LEFT OR RIGHT HAND INSTALLATION
The Automatic Opener can be installed on the left or right hand
side of the door (when looking out from the inside of the
garage). If your opener is to be installed on the RIGHT HAND
side of the door then go on to step 4. If the LEFT HAND side
is your selected side for installation the next step is to move the
motor wire connector on the control board. The connector plug
has to be removed and reconnected to the LEFT side of the
connector (Fig. 4). If you have made an error in selection and
wish to install to the RIGHT HAND side of the door, then
reconnect the connector plug to the RIGHT side of the connector (Fig. 5).
FIG. 3
FIG. 4
FIG. 5
INSTALLATION
9
5. FIXING DRIVE UNIT TO THE DOOR
(RIGHT HAND INSTALLATION)
The Automatic Openers Drive Unit can be fixed to the Roll Up
Garage Door in a variety of ways. Below we will describe one
method of fixing. Make sure there is enough side room (135mm
from end of door shaft to the wall) to slide Drive Unit onto
shaft.
PLEASE NOTE: THE INSTRUCTIONS FOR FIXING OF
THE DRIVE ASSEMBLY TO THE DOOR IS FOR RIGHT
HAND INSTALLATION.
FITTING DRIVE UNIT TO DOOR
(Fig. 6, Fig. 7, and Fig. 8).
1. Check that the door shaft U bolt is securely tightened on the
left hand side of the door.
2. Raise the door and tie a rope around the centre to secure the
roll.
3. Support the right hand end of the door with a suitable prop,
e.g. step ladder and soft padding to protect door surface.
WARNING: DO NOT ALLOW CHILDREN/PERSONS
AROUND THE DOOR AND PROP. SERIOUS PERSONAL
INJURY AND/OR PROPERTY DAMAGE CAN RESULT
FROM FAILURE TO FOLLOW THIS WARNING.
4. Check that Step 3. was completed. Carefully loosen and
remove the right hand door shaft U bolt.
5. Make sure that the door supporting prop is secure. While the
door is supported remove the right hand door mounting
bracket from wall.
6. Remove the Drive Unit from packaging. Try and rotate the
drive gear by pushing on the fork. If the gear does not rotate the
manual mode has to be selected. To select pull on the string
handle downwards, then release slowly. The drive gear should
now rotate. (Fig. 13).
7. Slide the Drive Unit over the door axle making sure that the
fork extends into and over one of the spokes of the door drum
wheel.
8. Refit the door mounting bracket to the wall. In some cases
the bracket may have to be re-positioned. Re-tighten the door
shaft U bolt. Remove door supporting prop and untie rope from
curtain.
9. Straighten the Drive Unit and position as per Fig. 8. Tighten
the two locking bolts firmly to secure the Drive Unit.
10. Check the manual operation of the door by raising and
lowering the door. The door should run smoothly and not catch
on any part of the Drive Unit.
11. Plug the connecting wire from the control box into the
bottom of the drive unit (Fig. 8).
FIG. 6
FIG. 7
FIG. 8
INSTALLATION
10
6. FIXING OF DOOR CURTAIN TO DRUM
WHEEL
The door curtain has to be secured to the drum wheel with suitable fasteners.
1. With the door in the fully closed position, mark the curtain
(Fig. 9) on both ends of the door.
2. Open door slightly to have access to the marked positions.
Secure the curtain to drum wheel using self drilling screws (two
on each end). The screws should be at least 90 degrees apart
(Fig. 9).
7. SETTING LIMIT SWITCHES
IMPORTANT NOTE: The O/S/C button and Transmitters
will not function until the Limits are adjusted and Step 8.1
is completed.
The Limit Cams, Limit Fine Adjustment Screws and Door
Drive buttons are colour coded to make the setting of the limits
as user friendly as possible.
The GREEN colours for OPEN LIMIT SETTING.
The RED colours for CLOSE LIMIT SETTING.
7.1 SETTING LIMITS FOR RIGHT HAND
INSTALLATION
1. With the Drive Unit in manual mode (Fig. 13) move the door
up by hand to the desired open position.
2. Remove the Limits Cover (Fig. 10). Rotate by hand in a anticlockwise direction the green limit cam (Fig. 11) until the cam
clicks the open limit switch.
3. Move the door down by hand to the desired closed
position.
4. Rotate by hand in a clockwise direction the red limit cam
(Fig. 12) until the cam clicks the close limit switch.
5. Connect power lead from the Drive Unit into, a general
purpose power outlet installed by a licensed electrical
contractor. Turn the Power On.
6. Re-engage the drive gear to door by pulling down on the
string and then releasing slowly (Fig. 13).
OPEN LIMIT ADJUSTMENT
Press in and hold the Green Open button (Fig. 11) The door
should start opening. Release the Green Open button when the
door reaches the desired open position. If the Green LED (Fig.
11) is illuminated and the desired limit position has been
reached then the limit adjustment is complete. If the Green LED
is illuminated but you are not happy with the door open
position, the Green Fine Adjustment Screw (Fig. 11) can be
adjusted to fine tune the open position. Adjust the screw anticlockwise to open the door more. To open the door less adjust
the screw clockwise. Each complete revolution of the
adjustment screw is equal to approximately 10mm of door
travel.
FIG. 9
FIG. 10
FIG. 11
INSTALLATION
11
NOTE: If the door has not reached the desired limit position by
more then 30mm, then it is recommended that the green limits
cam be adjusted again before the green fine adjustment screw is
adjusted.
CLOSE LIMIT ADJUSTMENT
Press in and hold the Red Close button. (Fig. 12). The door
should start closing. Release the Red Close button when the
door reaches the desired closed position. If the Red LED (Fig.
12) is illuminated and the desired limit position has been
reached then the limit adjustment is complete. If the Red LED
is illuminated but you are not happy with the door close
position, the Red Fine Adjustment Screw (Fig. 12) can be
adjusted to fine tune the close position. Adjust the screw anticlockwise to close the door less. To close the door more adjust
the Red Fine Adjustment Screw clockwise. Each complete
revolution of the adjustment screw is equal to approximately 10
mm of door travel.
NOTE: If the door has not reached the desired limit position by
more then 30mm, then it is recommended that the red
limits cam be adjusted again before the red fine adjustment
screw is adjusted.
7.2 SETTING LIMITS FOR LEFT HAND
INSTALLATION
1. With the Drive Unit in manual mode (Fig. 13) move the door
up by hand to the desired open position.
2. Remove the Limit Cover (Fig. 10). Rotate by hand in a
clockwise direction the Green Limit Cam (Fig. 14) until the
cam clicks the open limit switch.
3. Move the door down by hand to the desired closed
position.
4. Rotate the red limit cam in a anticlockwise direction by hand
(Fig. 15) until the cam clicks the close limit switch.
5. Connect Power Lead from the Drive Assembly into, a
general purpose power outlet installed by a licensed qualified
electrical contractor. Make sure that the Power Lead is safely
fastened away from any moving parts. Turn the Power On.
6. Re-engage the drive gear to door by pulling down on the
string handle and then releasing slowly (Fig. 13).
FIG. 12
FIG. 13
INSTALLATION
12
OPEN LIMIT ADJUSTMENT
Press in and hold the Green Open Button (Fig. 14) The door
should start opening. Release the Green Open button when the
door reaches the desired open limit stop position. If the Green
LED (Fig. 14) is illuminated and the desired limit stop position
has been reached then the limit adjustment is complete. If the
Green LED is illuminated but you are not happy with the door
open position, the Green Fine Adjustment Screw (Fig. 14) can
be adjusted to fine tune the open position. To open the door
more, turn the Green Fine Adjustment Screw clockwise. To
open the door less turn the Green Fine Adjustment screw anticlockwise. Each complete revolution of the adjustment screw is
equal to approximately 10mm of door travel.
NOTE: If the door has not reached the desired limit position by
more then 30 mm, it is recommended that the green limits cam
be adjusted again before the green fine adjustment screw is
adjusted.
CLOSE LIMIT ADJUSTMENT
Press in and hold the Red Close button (Fig. 15) The door
should start closing. Release the Red Close button when the
door reaches the desired closed limit stop position. If the Red
LED (Fig. 15) is illuminated and the desired limit position has
been reached then the limit adjustment is complete. If the Red
LED is illuminated but you are not happy with the door close
position, the Red Fine Adjustment Screw (Fig. 15) can be
adjusted to fine tune the close position. Adjust the screw clockwise to close the door less. To close the door more adjust the
screw anticlockwise. Each complete revolution of the adjustment screw is equal to approximately 10 mm of door travel.
NOTE: If the door has not reached the desired limit position by
more then 30mm, then it is recommended that the red limits
cam be adjusted again before the red fine adjustment screw is
adjusted.
FIG. 14
FIG. 15
INSTALLATION
13
8. SETTING OF OPEN AND CLOSE SAFETY
OBSTRUCTION FORCE
The Safety Obstruction Force is calculated automatically and
set in memory on the Automatic Opener. This applies to both
the Open Force and Close Force.
Warning: When step 8.1 is initiated the Garage Door will do
a full open and close cycle automatically. Please keep door
way clear to avoid any personal injury or damage to
property.
8.1 TO INITIALISE OBSTRUCTION FORCE
1. Press and hold down the close button 8 (Fig. 16), to move
the door to the fully closed position. Check that the RED LED
is steady ON, to confirm the door is set on the closed limit
position.
2. Press the Reset button 5 (Fig. 16) for two seconds, the door
should start opening. As soon as the door reach’s its fully open
position it will pause momentarily then start to close.
The door has to do a full open and close cycle with no
interruptions for the safety obstruction parameters to be
calculated and set automatically.
A default safety force pressure margin is preset in the factory.
Under normal operating conditions this default margin should
not be changed. If you are unhappy with the pressure you can
change it as below.
8.2 TO INCREASE FORCE PRESSURE
1. Press and hold the Force Margin Set button 1 (Fig. 16).
2. While holding down button 1 press the green Open button
3. The green LED will illuminate each time the green open but-
ton is pressed to indicate that the force pressure is being
increased. If the green LED flashes continuously when the open
button is being pressed, this indicates that the maximum force
pressure setting has been reached.
8.3 TO DECREASE FORCE PRESSURE
1. Press and hold the Force Margin Set button 1 (Fig. 16).
2. While holding down button 1 press the red Close button 8.
The red LED will illuminate each time the red Close button is
pressed, to indicate that the force pressure is being reduced.
When the red close button is being pressed and the red LED
flashes continuously, this indicates that the minimum force
pressure setting has been reached.
8.4 TO RECALL FACTORY SET FORCE MARGIN
1. While holding down the Force Margin Set button 1 press the
RESET button 5 for two seconds.
2. Release both buttons. The default setting should now be
recalled.
IMPORTANT NOTE:
Whenever the Limit Switches or Cams are
adjusted the safety obstruction force has to be
re-initialised because the door travel distance
may have changed. To re-initialise please follow
STEP 8.1 above.
FIG. 16
FIG. 17
INSTALLATION
14
8.5 SAFETY OBSTRUCTION TEST
TESTING CLOSE CYCLE
1. Open the door by pressing the Yellow O/S/C button 4 (Fig.
18).
2. Place a length of timber 100mm X 50mm on the floor
directly under the door (Fig. 17).
3. Press the Yellow O/S/C button to close door. The door
should strike the object and start to re-open.
TESTING OPEN CYCLE
1. Close the door by pressing the Yellow O/S/C button 4. (Fig.
18).
2. Press again to open the door. When the door reaches half the
opening distance grab the bottom rail of the door firmly, the
door should stop.
If the door does not reverse readily when closing, or stop when
opening, the force may be excessive and need adjusting, refer
to STEP 8.1, 8.2, 8.3 and 8.4.
IMPORTANT WARNING: If the door is closing and is
unable to reopen when obstructed discontinue use. Do not
use a door with faulty obstruction sensing. Repair fault and
re test before using.
9. SETTING TRANSMITTERS CODES INTO DOOR
OPENER
The Remote Transmitters and Wall Mount Transmitters can be
programmed into the Door Opener as below. Make sure to
connect the battery to the Transmitters. The memory in the
Openers receiver can store up to 27 different remote control
transmitters.
9.1 STORING THE TRANSMITTERS CODE
1. Press and hold the blue Door Code button on the Control
Panel button 9 (Fig. 18).
2. Press the button (one of four) on the Transmitter you would
like to use to control the door for approximately two seconds,
(Fig. 18). Pause for two seconds. Press the same button again
on the Transmitter for approximately two seconds.
3. Release the blue Door Code button 9.
4. Press the Transmitter button to see if it operates the door. If
you wish you can code in all four buttons on the Transmitter so
all four can operate the same door.
9.2 STORING ADDITIONAL TRANSMITTER(S) FROM
A REMOTE LOCATION
Using this method you don’t need to have access to the control
panel on the Door Opener. However, you do need a transmitter
that is pre coded to the controller’s receiver.
IMPORTANT NOTE: The Door must be activated when
the step below is preformed. The moving Door is to confirm
from a remote location that the correct button was pressed
and the transmitter is in range of the opener of a pre coded
Transmitter.
1. Take any pre-coded Transmitter. Press the button for the
function you require until the door is activated and then release.
2. Then using a small needle press and hold firmly for 2
seconds through the Coding Hole (Fig. 18).
3. Within 10 seconds take the additional transmitter you wish
to code and follow STEP 9.1 para 2, as above.
FIG. 18
FIG. 19
INSTALLATION
15
10. SETTING THE TRANSMITTER TO
OPERATE THE COURTESY LIGHT
The Transmitter can be programmed to operate the Courtesy
Light on the Door Opener.
1. Press and hold Light Code button 10 on the Control Panel
(Fig. 20).
2. Press the button on the Transmitter you would like to use to
control the light for approximately two seconds. Pause for two
seconds. Press the same button again on the Transmitter for
approximately two seconds.
3. Release the Light Code button 10.
4. Press the Transmitter button to see if it operates the light.
11. DELETING PROGRAMMED CODES
11.1 DELETING A STORED TRANSMITTER CODE
1. Select the transmitter you want to delete.
2. Press and hold the blue Door Code button 9 (Fig. 21) on the
Control Panel.
3. Press the Transmitter button you would like to delete for two
seconds. Pause for two seconds. Press the Transmitter button
again for two seconds.
4. Release the blue Door Code button 9. The code should now
be deleted. Confirm this by pressing the transmitter
button to see if it can operate the door. The door should not
respond.
11.2 DELETING ALL STORED TRANSMITTER
CODES
1. Turn the Power Off to the Drive Unit.
2. Press and hold the blue Door Code button 9 (Fig.21) on
the Control panel.
3. Turn the Power On again, while holding the Blue Door Code
button until the Coding LED illuminates. (approx. 10 to 12
seconds)
4. Release the blue Door Code button 9. All the stored codes
including the Courtesy Light Codes should now be deleted.
5. Confirm this by trying to operate the door by pressing one
of the deleted transmitters.
12. SETTING OF COURTESY LIGHT TIME
The preset courtesy light time on the Door Opener is 3
minutes. This time can be changed as below.
1. Press in together and hold the Auto Close Time button 6 and
Force Margin Set button 1 (Fig. 22).
2. While holding in the two buttons, press the green Open
button 3 (Fig. 22). Each press of this button will add 10 secs to
the light time.
3. To decrease the time follow step 1 and press the red Close
button 8 (Fig. 22). Each press will deduct 10 secs from the light
time.
4. To recall the factory set default light time press in and hold
together the Auto Close Time button 6, the Force Margin Set
button 1 and the Reset button 5 for about 2 seconds. (Fig. 22).
FIG. 20
FIG. 21
FIG. 22
INSTALLATION
16
13. FITTING OF SAFETY PHOTO ELECTRIC
BEAM (OPTIONAL)
Locate the Photo Electric Beam (P.E.) normally closed contact
type in a strategic location within doorway. Remove shunt from
P.E connector (Fig. 23) and connect the plug from the P.E.
wiring harness to P.E. connector (Fig. 24). Follow the wiring
diagram supplied with the P.E. for wiring of the P.E.
WARNING: When using auto close and P.E. beams, the
doorway must be clear of all obstructions and persons at all
times. The location of the beam and manner in which it is
installed might not give safety protection at all times. Check
to make sure that the height of the beam and type used give
maximum protection possible.
14. SETTING OF AUTO CLOSE TIME
IMPORTANT NOTE:
IT IS COMPULSORY TO INSTALL A PHOTO
ELECTRIC BEAM BEFORE USING THE AUTO CLOSE
MODE.
The Auto Close timer will only start after the Photo Electric
Beams (P.E.) path is broken and the auto close time has been
set. If the P.E. path is not broken the door will remain open till
the path is broken. If the Door Opener incurs an obstruction
(not from the P.E.) while closing the door will re-open and not
auto close.
After the setting of the auto close mode, whenever the door is
in the open position the open limit green LED will flash to
indicate that the auto close mode is in operation.
SETTING AUTO CLOSE TIME
1. Press in and hold the Auto Close Time button 6 (Fig. 25).
2. While holding in the Auto Close Time button, press the
green Open button 3 (Fig. 25). Each press of this button will
add 5 seconds to the preset auto close time of 0 seconds.
(0 seconds = “OFF”)
3. To decrease the time follow step 1 and press the red Close
button 8. Each press will deduct 5 seconds from the auto close
time.
4. Press the O/S/C button 4 (Fig. 25) or Transmitter to open the
door. While the door is opening break the path of the P.E. Beam,
this will initialise the auto close mode. When the door reaches
the fully opened position, the door will pause for the set auto
close time and start to auto close.
FIG. 23
FIG. 24
FIG. 25
INSTALLATION
17
FUNCTION
MAXIMUM MOTOR RUN TIME
COURTESY LIGHT TIME
OBSTRUCTION FORCE MARGIN
AUTO CLOSE TIME
DEFAULT
30 Sec.
3 Min.
10
0 Sec = Off
STEP
—
10 Sec.
1
5 Sec.
MAXIMUM
—
10 Min.
20
4 Min.
Factory Default Settings
Door Status Indicators
OPEN
CLOSE
OPENING
CLOSING
DOOR TRAVEL STOPPED
DOOR OBSTRUCTED WHILE OPENING
DOOR OBSTRUCTED WHILE CLOSING
DOOR OVERLOADED
DOOR & OPENER APPROACHING
OVERLOAD
DOOR HAS APPROACHED OVERLOAD
3 TIMES IN 8 CYCLES
DOOR IN OPEN POSITION WITH AUTO
CLOSE MODE SELECTED
MAINS POWER TO OPENER INTERRUPTED
ON
FLASHES
FLASHES
FLASHES
ONE SEC
FLASHES
RAPID
FLASHES
ON
FLASHES
FLASHES
ON
FLASHES
10 TIMES
BEEPS ON
& OFF
BEEPS ON
& OFF
BEEPS ON
& OFF
CONSTANT
BEEPS
ONE BEEP
AT START
DOOR OPENER STATE
OPEN
LED
GREEN
CLOSE
LED
RED
DOOR
STATUS
LED
YELLOW
LIGHT BEEPER
SPARE PARTS LIST
18
WHEN ORDERING SPARE PARTS
PLEASE QUOTE THE ORDER
CODE NUMBER TO YOUR YOUR
INSTALLER/DISTRIBUTOR
TROUBLE SHOOTING
19
SYMPTOM POSSIBLE CAUSE REMEDY
Door will not operate Main Power not turned on Turn on Mains Power
Door is obstructed Remove obstruction
Door in locked or motor jammed Unlock door and Inspect door and remove jam
Door will not reverse when Door needs to be re-initialised Fully close the door and press the Reset
obstructed button (refer installation instruction step 8.1)
Door moves downwards and There could be an obstruction in door way. Remove obstruction.
reverses itself upwards Adverse weather conditions (wind or cold) Increase the force pressure and / or re-initialise the
causing door to stiffen and become tight door (refer installation instruction step 8.1 and 8.2)
in tracks.
Door operates from drive unit Indicator on transmitter not lighting Battery flat or battery lead broken
but not from hand transmitter Code not stored in openers receiver Refer to installation instructions step 9
Drive unit aerial wire not extended Extend aerial wire
Battery flat Replace battery (12V)
Door does not close fully Limit micro switch incorrectly adjusted Re-adjust limit switch (refer installation
instruction – step 7 and 8)
Door does not open fully Limit micro switch incorrectly adjusted Re-adjust limit switch (refer installation
instruction – step 7 and 8)
Lights malfunction or keep Globe blown or incorrect globe Replace with 24V DC 15 watts Festoon globe.
blowing.
Courtesy Light Flashing The Door Opener has detected an overload Discontinue use of the Door Opener and call a
condition. The door may be jamming, lost qualified service man to repair door. Continual
Spring tension or needs repair. use may cause severe damage to the door and
Door Opener.
Auto close not working P.E. Beam faulty or wiring broken Repair P.E. or broken wire
P.E. Beam obstructed or dirty Remove obstruction/clean from the path of PE.
Door obstructed when closing Close door using Transmitter. Refer to installation
instruction – step 14
Auto Close time or mode not set Refer to installation instruction – step 14.
TECHNICAL SPECIFICATIONS
INPUT VOLTAGE: 220V- 240V AC 50Hz
(Other voltages available upon request
110V AC 60Hz, 127V AC 60Hz)
TRANSFORMER PRIMARY VOLTAGE: 220V / 240VAC
SECONDARY VOLTAGE: 24V AC 100 VA
CONTROLLER VOLTAGE: 24V DC
OPENER LIFTING FORCE: 250 N
OPENER OPENING/CLOSING LIMITS TRAVEL: 3.5 Turns of Door Drum Wheel
RECEIVER TYPE: UHF 433.92 MHz. AM Receiver
RECEIVER CODE STORAGE CAPACITY: 27 x 4 Button Transmitter Codes
TRANSMITTER FREQUENCY: 433.92 MHz
CODING TYPE: Hopping Code
No. of CODE COMBINATIONS: Over 4.29 Billion Hopping Codes
CODE GENERATION: Non-linear Encryption Algorithm
BATTERY VOLTAGE: 12 Volts
MOTOR TYPE: Permanent Magnet Direct Current
MOTOR VOLTAGE: 24V DC
GLOBE: Festoon Type - 15w 24V DC
WARRANTY AND EXCLUSION OF LIABILITY
Subject to all of the matter set out below, Automatic Technology Australia Pty Ltd (“ATA”) WARRANTS for twenty four (24)
months from the date of purchase (specified in the receipt sales docket) that the Garage Door Opener System contained in the
accompanying packaging (the “Product”) is free of any defects in material and workmanship rendering it unmerchantable.
This warranty referred to above applied only where:
a) the consumer seeking to rely on the said warranty;
1) returns the Product which it claims to be defective; and
2) presents the relevant sales docket and this warranty document,
To the retailer from whom the Product was purchased to confirm that date of purchase; and
b) the purchaser notified ATA or the retailer from whom the Product was purchased of the alleged defect in the Product
immediately upon experience or learning of the alleged defect.
Except for the warranty against defects in material and workmanship set out above, ATA gives no warranties of any kind whatsoever, whether express or implied or whether statutory or at common law, in relation to the Product, and all warranties of
fitness for particular purpose and other warranties of whatsoever kind relating to the Product are hereby declaimed. Without
limiting the generality of the foregoing, ATA disclaims any liability of whatsoever nature in respect of any claim or demand loss
or damage which arise out of;
a) accidental damage to or normal wear and tear to the Product or to the Product’s components;
b) flood, rain, water, fire or lightning;
c) incorrect, improper or unreasonable maintenance and/or use;
d) installation, adjustment or use other than ATA which is not in accordance with the instructions set out in installation instruction incorporated in the document;
e) attempted or complete modification or repairs to the Product carried out by a person who is not authorised by ATA to carry
out such modification or repairs;
f) faulty or unsuitable wiring of structure to which the Product is fixed or connected; and
g) radio (including citizen band transmission) or any electronic interference.
h) blown fuses or damage caused by electrical surges.
i) damage caused by insects.
ATA’s liability under the warranty set out above is limited, at ATA’s absolute option, to replacing or repairing the Product which
ATA, in its unfettered opinion, considers to the defective either in material and/or workmanship or to credit the consumer with
the price at which the Product was purchased by the consumer.
Where the Product is retailed by any person other than ATA, except for the warranty set out above, such person has no authority
from ATA to give any warranty or guarantee on ATA’s behalf in addition to the warranty set out above.
Loading...