Helpline Telephone: 01842 819130 Installation and Operation manual - SMS Alarm Further information is available on www.automatedenvironmentalsystems.co.uk
SMS-DIALLER
AUTOMATED ENVIRONMENTAL
SYSTEMS™
SMS-DIALLER
Connect the float switch to the sensor inputs in the alarm panel (please refer to
the float switch manufactures wiring diagram to select the correct wire colours
and polarity required to make the float switch make contact when in the up
position.
Connect the alarm panel to a 230VAC supply as shown.
Test the alarm panel is working by holding the float switch in the up position for
5 seconds.
Please note that the “test” button must be pressed for 5 seconds before the
alarm will trigger.
Setup and operation is performed by simple SMS text messages including
adding and removing user telephone numbers. A complete list of accepted
telephone numbers can be viewed via SMS text message. The memory can
also be scanned to see if it contains an individual number and the result is
displayed by the on-board LED and by SMS text message.
Wiring for an SMS Dialler (2 channel version)
N E L
SIM
Card
Pre-wired power connection
Float switch/Pressure switch inputs
(see connection details on adjacent page)
Relay
connections
(connection is
dependant on
what is connected)
Antenna
Connection
(press onto
button
connector)
Jumper
(used to lock master
number setup,
leave as supplied)
Note:
The SMS Diallers
are not supplied
with cable entry or
grommets. Hole
positions for
mounting and cable
entry are at the
discretion of the
end user.
Wiring for an SMS Dialler (4 channel version)
N E L
SIM
Card
Pre-wired power connection
Float switch/Pressure switch inputs
(see connection details on adjacent page)
Relay
connections
(connection is
dependant on
what is connected)
Antenna
Connection
(press onto
button
connector)
Jumper
(used to lock master
number setup,
leave as supplied)
Note:
The SMS Diallers
are not supplied
with cable entry or
grommets. Hole
positions for
mounting and cable
entry are at the
discretion of the
end user.
Connecting the float/pressure switch:
The float switch comes with a flex mounded into the float head. If
required the length of this cable can be extended using a 3 core 1mm²
electrical flex and a suitable junction box. The colours of the wires may
vary depending on the float switch supplied. Connect one side of the
float switch to GND and the other to IPA, this will trigger an SMS text
when float switch (1) activates. If fitting a second float switch or a
pressure switch connect one side to GND (this is a common connection)
and the other side to IPB. This will send a different text message when
either the float or pressure switch activates.
Input Connections for Float/Pressure Switch
(2 channel version)
SMS Dialler
Float Switch
1
GND
IP A
IP B
Float Switch
2
The colours of the wires may vary depending on the float switch supplied
Input Connections for Float/Pressure Switch
(4 channel version)
AN2
AN1
GND
IPD
IPC
IPB
IPA
GRD
V IN B
A
Not used
Not used
Not used
Connecting the float/pressure switch:
The float switch comes with a flex mounded into the float head. If
required the length of this cable can be extended using a 3 core
1mm² electrical flex and a suitable junction box. The colours of the
wires may vary depending on the float switch supplied. Connect
one side of the float switch to GND and the other to IPA, this will
trigger an SMS text when float switch (1) activates. If fitting a
second float switch or a pressure switch connect one side to GND
(this is a common connection) and the other side to IPB. This will
send a different text message when either the float or pressure
switch activates. Continue to connect in the same way for IPC
and IPD
Float switch 4/
input 4
Float switch 3/
input 3
Float switch 2/
input 2
Float switch 1/
input 1
The colours of the wires may vary depending on the float switch supplied
Pre-wired power connection
The clear all function is done as a
precaution to ensure that there are no
settings in the system that could
interfere with your new settings.
Text:
Quick Guide Settings for SMS
1. Clear All
NOTES: In order to set the Master Number, the jumper on the printed circuit board must be placed across
pins 3 and 4
CLEARALL
Send the message to the mobile
number in the SMS alarm panel (this is
the number assigned to the SMS card
when it was purchased).
The system requires a master number
in order to work. This number will allow
the owner to send and receive
information to and from the SMS alarm
panel.
Text:
2. Master Number
MASTER (phone number)
Note: There must be a space between
the word MASTER and the phone
number you want to use.
Example: MASTER 07891584789
Send the message to the mobile
number in the SMS alarm panel.
This is the 1st number that a text
message will be sent to in the event of
an alarm.
Text:
3. Number to Text
TEXTNUM (phone number)
Note: There must be a space between
the word TEXTNUM and the phone
number you want to use.
Example: TEXTNUM 0711365894
Send the message to the mobile
number in the SMS alarm panel.
4. Additional numbers
to text
Repeat as for step 3.
The order in which the texts are made
follows the order in which they are
input here:
Text:
TEXTNUM (phone number
Continue to repeat as for step 3. until
all the number have been input. There
is a maximum of 512 numbers that can
be entered.
5. Inputting the text message
to be sent out
This is the message that will be sent in
the event of an alarm.
Text:
Note: this will output a text for any
device that is connected to GRD and
input 1 on the PCB.
CUSTOMA (message).
There must be a space between the
word CUSTOMA and the text of the
message to be sent and there must be
a fullstop at the end.
Example: CUSTOMA There is an
alarm in area A please attend.
A maximum of 64 characters can be
used to create the message.
If there is also a device connected to
GRD and input B then a separate
message can be set up which will show
the recipient which device has gone
into alarm
Setup as for CUSTOMA but use the
command CUSTOMB at the front
instead.
Example: CUSTOMB There is a
flood detected in the plant room.
Repeat for inputs C and D as above.
6. Keeping the SMS card
activated
This is a requirement if a PAYG SIM
card has been purchased as inactivity
for more than 30 days will make it go to
sleep.
Text:
KA (mobile number of the
SMS unit),(number in
days)
There must be a space after the KA
and a comma between the phone
number and the number of days.
Example: KA 07895648532,28
In this example the phone number of
the SMS dialler is 07895648532 and it
will automatically send out a routine
text message every 28 days.
It is recommended to set the system up
to send a routine message at least
every 28 days.
Other Settings for SMS Alarm
This would be set to help avoid false
alarms from systems that could be
susceptible to spirulas signals. An
example of this would be a tank
containing liquid where a float switch
has been set up to monitor how full it is.
In this scenario the top of the liquid
could have some movement (waves)
which will send a signal from the float
switch a number of times as the float
moves up and down. By setting a
delay time the SMS alarm panel will not
send out a text message until it has
received a constant signal for a defined
length of time.
Text:
Example: HOLD 60
This will wait for a continuous signal of
1 minute before sending the text
message.
Note: If you have a second device
fitted to GRD and input B then you can
apply a delay to this as well. Send the
text message:
7. Delaying the text message
before it’s sent
HOLD (number in seconds)
It is advisable to test the signal strength
for the particular network you have
decided to go with to ensure the SMS
alarm will operate correctly.
Text:
You will receive a reply to your phone
that looks like this:
The number relates to the signal
strength. A figure of 15 or above is
ideal for reliable operation. However
the system will still work down to a
figure of 8, but there could be times
when it becomes unresponsive.
8. Testing the signal strength
CSQ
9. Checking what numbers
are stored
This will send a text message to your
phone of all the different numbers
currently stored and the order they are
in.
Text:
List
Please note that only the last 8 digits of
the number will be shown in the text
reply.
HoldB (number in seconds)
In both cases there needs to be a
space after the HOLD/HoldB words
Repeat for inputs C and D as above.
>RSSI (number)
If anything is connected to the relay
output, this will need to be switched on.
Text:
This will activate the relay, please note
there needs to be a space between the
word EXIT and ENABLE
10. Activating the Relay
EXIT ENABLE
The length of time that the relay is
activated can be set so that if you want
to switch off the device connected to
the relay (such as a sounder/beacon)
after a period of time you can.
Text:
This will activate the relay for a time in
minutes, please note there is a space
between RLY and TIME but no space
after TIME where the number is typed.
There also needs to be a full stop at the
en of the text message.
Example: RLY TIME60m.
This will activate the relay for 60
minutes.
11. Relay Activation Time
RLY TIME(number)m.
This command sets the repeat time
between sending the message out
should the first time the message is
sent not be acknowledged. The time
delay can be set between 1 second
and 250 minutes.
Text:
Example: HOLDA R60
This will wait for a 1 minute before
sending the text message out again.
Note: If you have a second device
fitted to GRD and input B then you can
apply a repeat to this as well. Send the
text message:
7. Resending the message if
not acknowledged
HOLDA R (seconds)
HoldB R (seconds)
In both cases there needs to be a
space after the HOLDA/B before the R
but no space between the R and the
number.
Repeat for inputs C and D as above.
Other features that can be set up in the SMS dialler:
Call numbers, where a call is made to a programmed number as well as a text message sent. Text Callnum (number)
Removing a telephone number. Text REMOVE (telephone number)
Finding a stored number in the SMS dialler memory, text QUERY (telephone number)
Changing the maximum ring time. This is the length of time the dialler will attempt to connect with each stored number before moving on to the next if not acknowledged.
Text RTIME (time in seconds)
Assigning numbers to either input A only or input B only in order that only certain numbers are text should A go into alarm and different numbers if B gets triggered. Text
TEXTNUMA (number) or TEXTNUMB (number)
International numbers can be programmed by using the + symbol instead of the 00 for the country code. Example: +4678921568541
Checking the balance on the SIM card. Networks require either an SMS text message to be sent to retrieve a balance or a network code to be dialled. Please check with
your network provider to find your balance checking method.
Helpline Telephone: 01842 819130 Installation and Operation manual - SMS Alarm Further information is available on www.automatedenvironmentalsystems.co.uk
Loading...