Autoglide Magro-500 J, Magro-650 J User Manual

Magro-J – Series

Swing Gate Opener

User Manual

www.autoglideglobal.com

2018

Dear users,

Thank you for choosing this product. Please read the manual carefully before assembling and using it.

Please do not leave out the manual if you send this product to a third party.

1. Safety Instruction

Please ensure that the using power voltage matches with the supply voltage of gate opener

(AC110V or AC220V); kids are forbidden to touch the control devices or the remote-control unit.

The remote-control unit is controlled by a single button mode or three button mode (please refer to

the instructions of the remote control in accordance with the actual gate opener type). The indicator

light on the remote-control unit will flicker when the button on it is pressed. Main engine and gate

can be unlocked by disengagement wrench and the gate can move with manual operation after

disengagement.

Please ensure that no one is around the main engine or gate when the switch is operated and it is

usually demanded to examine the stability of installation. Please temporarily stop using if the main

engine needs repairing or regulation.

The installation and maintenance of the products must be carried out by professionals.

2

2. Packing List (standard)

No. Picture Name Quantity

1

2

3

4

5

6

Main engine 2

Manual release bar 1

A

A

B

B

C

C

D

D

Remote control 2

Control box 1

Wall bracket 4

Front mounting bracket 2

7

Connecting bracket 2

8

Mounting screw (short) 2

9

Mounting screw (length) 2

10

Screw M8×25 4

11

Nut M8 8

12

Safety stopper (Optional) 1

3

2. Packing list (optional)

No. Picture Name Quantity

1

1 2 3

5 6974

8

2

0

3

4

5

3. Technical parameters

Infrared sensor 1

Wireless keypad 1

Alarm lamp 1

Electronic lock 1

Storage battery 2

Model

Power supply

Motor power

Gate moving speed

18~22 second per 90 (approx)

Max.single-leaf weight

Max.single-leaf length

Max.piston stroke: 34cm

Max.force

Remote control distance

Magro - 500 J

220V/50Hz;110V/60Hz

80W

250 Kg

2.5M

1500N

≥30m

Magro - 650 J

220V/50Hz;110V/60Hz

80W

18~22 second per 90 (approx)

325 Kg

3.0M

54cm

1500N

≥30m

Remote control mode Single /Three button mode Single / three button mode

Storage battery (optional)

Noise

DC24V (4.5AH or 9.0AH) DC24V (4.5AH or 9.0AH)

≤58dB ≤58dB

Working duty S2, 30min S2, 30min

Recording of up remote controls

25 25

Frequency 433.92 MHz 433.92 MHz

Working temperature -20°C - +70°C -20°C - +70°C

Package weight 17Kg 19Kg

4

4. Installation

Magro J Series swing gate opener is applicable to single leaf gate weight less than 225/300 kg, and
length of the single leaf swing gate should be less than 2.5m/3m. The drive mode adopts the worm
and worm gear to combine the screw rod transmission. This gate opener must be installed inside
the enclosure or yard for protection.

4.1 Installation drawing

④

③

①

②

⑧

⑤

⑥

⑦

Figure 1

Control box; ② Gate opener; ③ Gate; ④ Alarm lamp (optional);

①

Infrared sensor (optional); ⑥ Stopper; ⑦ Remote control; ⑧ Wireless keypad (optional);

⑤

4.2 Size of main engine and accessories

4.2.1 Size of main engine

n

i

M

0

6

2

1 2 3

5 6974

8

0

x

a

0

M

7

9

Magro - 500 J

104

190

5

4.2.2 Size of mounting plate

x

Ma

0

7

3

1

Magro – 650 J

Figure 2

n

i

M

0

8

2

104

190

1

8

5

.

0

7

0

4

2× 8

φ

.5

Front mounting bracket

Figure 3

4.3 Installation steps

4.3.1 Preparation before main engine installation

a) Before installing the door opener, please confirm the correct installation of the door to ensure that
the door can be easily manually operated, and the door safety stopper can effectively prevent the
door to continue moving.
b) Install the electric lock, the distance between the door bottom and ground should be 40-50mm. If
not install the electric lock, the distance between door bottom and ground should be ≥20mm;
c) The main engine recommended mounting height is about 300 ~ 800mm from the ground, and
make sure there are reliable fixed points for mounting brackets.

Cable

In order to ensure the normal operation of the door opener and protect the cable from damage,
please use PVC pipe laying motor, power cable, and control cables, and separate two PVC pipes to
lay (motor and power cable) and (control cable), respectively.

3

4

Wall bracket

7

.

5

6

Mounting brackets

In order to install the Magro - 500 J / Magro - 650 J main engines firmly, recommend to use the
expansion screws to fix the mounting brackets.

4.3.2 Accessory

a) Before installing the main engine, install the wall bracket on the wall, then fix the connecting
bracket, and install the front mounting bracket on the door.

Note: Please detect by gradienter before fixing, to ensure that the front mounting bracket
and the connecting bracket in the same level.

Hexagon screw

Expansion screw

Hexagon screw

Nut

Nut

Figure 4

b) The connecting bracket and the wall bracket can be connected according to different conditions,

as shown in figure 5.

c) Users shall prepare power cables for the control box and main engines, according to different

installation environment; the power cable of the control box is not less than 3 cores, and the motor

cable with 2 cores. If you need to install electric locks, infrared sensor, alarm lamp, external button

switch and other external equipment, please increase corresponding the embedded wire, and the

sectional area of electric lock cable core shall not be lower than 1.5mm², others shall not be lower

than 0.5mm². The length is determined by the user of according to the situation in the installation

site.

Figure 5

7

Note: The pipe outlet should be facing down to avoid rain water entering the pipe along the cable.

d) Before the installation, please unlock the main engine. Method: Remove the cover, insert the

manual release bar, rotate the bar until the release, as shown in Figure 6, then turn the telescopic

arm to make it easily stretch.

Left engine

Right engine

Figure 6

4.3.3 Main engine installation

As shown in Figure 7, the tail of the main engine and the connecting bracket are fixed together
through the installation of screws, and then manually adjust the telescopic arm to the appropriate
length, and finally fix the telescopic arm connector and the front mounting bracket with the
installation screws. Pull the door after the completion of the installation to ensure the entire process
flexible without jamming.

8

Mounting screw (length)

Nut

Figure 7

Installation direction: door open facing inward (Magro - 500 J)

Note:Note: SafetySafety stopperstopper mustmust bebe installedinstalled

B

A

Mounting screw (short)

Nut

L

K

L=620+5L=620+5
K＜620+340620+340

Figure 8

9

100 110 120 130 14 0 150 160 170 180 190 200

100
110
120
130
140
150
160
170
180
190
200

mmmm

Max 90°

Max 120°

Max 110°

Max 100°

B

A

Figure 9

Note: Value B must be close to or equal to the value A to obtain the best mechanical
advantage.

Installation direction: door open facing outward (Magro - 650 J)

Note:Note: SatetySatety blockblock mustmust bebe
installed,installed, isis proviedprovied byby installerinstaller

K

L=620+5L=620+5
K＜620+340620+340

B

A

Figure 10

L

Note:Note: SafetySafety stopperstopper mustmust bebe installedinstalled

10

100 110 120 130 140 150 160 170 180 190 200

100
110
120
130
140
150
160
170
180
190
200

Max 90°

Max 100°

Max 110°

B

Max 120°

mmmm

A

Figure 11

Note: Value B must be close to or equal to the value A to obtain the best mechanical
advantage.

Installation direction: door open facing inward (Magro - 500 J)

Note:Note: SafetySafety stopperstopper mustmust bebe installedinstalled

B

A

K

L

L=820+10L=820+10
K＜820+540820+540

Figure 12

11

100 12 0 140 1 60 180 200 220 240 260 280 300

100
120
140
160
180

200
220
240
260
280
300

mmmm

Max 120°
Max 110°
Max 100°
Max 90°

A

Figure 13

Note: Value B must be close to or equal to the value A to obtain the best mechanical
advantage.

Installation direction: door open facing outward (Magro - 650 J)

B

Note:Note: SatetySatety blockblock mustmust bebe
installed,installed, isis proviedprovied byby installerinstaller

K

L=820+10L=820+10
K＜820+540820+540

B

A

L

Note:Note: SafetySafety stopperstopper mustmust bebe installedinstalled

Figure 14

12

100 120 140 160 180 200 220 240 260 280 300

100
120
140
160
180
200
220
240
260
280
300

mmmm

Max 90°
Max 100°
Max 110°
Max 120°

A

Figure 15

Note: Value B must be close to or equal to the value A to obtain the best mechanical
advantage.

4.3.4 Size of control box

B

210

Figure 16

127.5

275

Warnings

·To ensure safety, when door open facing outward, the safety block must be installed at the OPEN
limit position to prevent the door opening angle from exceeding the machine range; the safety
stopper must be installed at the CLOSE limit position, to make two doors stopping at the CLOSE
limit position accurately (as shown in figure 10, 14). When door open facing inward, the safety
stopper must be installed at the CLOSE limit position (as shown in figure 8, 12).

·Before installing the main engine, make sure that the main engine and components are in good
mechanical performance and that the door can be operated manually.

·One control unit can control driving one main engine or two main engines.

·Earth leakage circuit breaker must be installed where the gate movement can be seen, and the
minimum mounting height of control box is 1.5m to protect it from being touched.

·After installation, please check whether the mechanical property is good or not, whether gate
movement after manual unlocking is flexible or not, and whether the infrared sensor (optional) is
installed correctly and effectively.

4.3.5 Control board wiring

AlarmAlarm lamplamp

MainMain engineengine 1

MainMain engineengine 2

ElectricElectric locklock

+24VDC+24VDC

CommonCommon terminalterminal

InfraredInfrared protectionprotection

15VDC15VDC

DoorDoor closeclose buttonbutton
CommonCommon terminalterminal

Open/Stop/closeOpen/Stop/close controlcontrol buttonbutton

CommonCommon terminalterminal

SingleSingle doordoor openopen buttonbutton

TestTest buttonbutton

LearningLearning buttonbutton

PK300DC M-2PK3 00DCM-2

RY5RY5

LIGHTLIGHT

DCDC24V24V

MOTORMOTOR 1 MOTORMOTOR 2 LOCKLOCK

M1M2

IN5408IN5408

IRIRCOMCOM+PWR+PWR

+

-

15V15V

P.SWP.SW P.SWP.SW

OPOP

CLCL

1

2

LED8LED8

LED7LED7

LED6LED6

CLCL

OPOP

VX1VX1

LED3LED3

LED4LED4

OPOP

CLCL

VX2VX2

RY8RY8

LED2LED2

LOCKLOCK

6.2V6.2V

D20D20

LED7LED7

CN4CN4CN3CN3CN2CN2

CN5CN5

SENSORSENSOR

C8C8

U2U2

U3U3

78L0578L05

C11C11

U4U4

TESTTEST

D11D11 D10D10

6A106A10

6A106A10

C2C2 C1C1

470UF470UF 470UF470UF

10UF10UF

C4C4

RY1RY1RY1RY1RY2RY2

RY4RY4

10UF10UF

C4C4

RY6RY6

D13D13

6A106A10

D12D12

6A106A10

U5U5 78127812

Q2Q2

MOTOR1MOTOR1 MOTOR2MOTOR2

Q3Q3

AN1AN1

RX1RX1

IC2IC2

F1F1

LEARNLEARN

ACAC FUSEFUSE

LED1LED1

U1U1

C3C3

78157815

10A10A

POWERPOWER

ACAC

VR1VR1

VR2VR2

D14D14

6A106A10

FUSEFUSE

8A8A

LM317LM317U6U6

15A15A

+BATTERY-+BATTERY-

REVREV

24VAC24VAC

BattaryBattary

Figure 17

Wiring instruction:

POWER AC terminal 24VAC alternating current power.

＋

BATTARY－ terminal Storage battery.

8P terminal:

LIGHT Alarm lamp (24VDC);

MOTOR 1 Main engine 1;
MOTOR 2 Main engine 2;
LOCK Electronic lock (24VDC).

CN2 terminal：

PWR Power supply for fittings +24VDC;

＋

COM Common;

IR Input of infrared sensor (N.C.).

CN3 terminal: Power supply for fittings 15VDC.

CN4 terminal: Signal input of gate close control button;

Control button common terminal.

CN5 terminal: Open/Stop/Close/Stop loop control button;

Control button common terminal;

Single door opening button.

Transformer wiring

ACAC FUSEFUSE

D12D12D13D13

LED1LED1

U1U1

C3C3

78157815

10A10A

U5U5

78127812

TransformerTransformer outputoutput 24VAC24VAC

POWERPOWER

ACAC

MOTOR1MOTOR1 MOTOR2MOTOR2

VR1VR1 VR2VR2

D14D14

6A106A10

TransformerTransformer inputinput

FUSEFUSE

220VAC/110VAC220VAC/110VAC

8A8A

LM317LM317U6U6

15A15A

RX1RX1

F1F1

+BATTERY-+BATTERY-

REVREV

15

DIP switch

Dial Function

1 Door closing delay function:

ON: Enabled - Motor 2 is 5 seconds delay to close the door than Motor 1;
OFF: Disabled.

2 Door opening status:

ON: Enabled - Motor 1 and motor 2 conduct 0.5-second close action before open
the door;
OFF: Disabled.

3 Single / Double door mode:

ON: Single door mode;
OFF: Double door mode.

4 /

Automatic close function:

5

5 ON 6 ON——Automatic close time is 60s;
5 ON 6 OFF——Automatic close time is 10s;

6

5 OFF 6 ON——Automatic close time is 5s;
5 OFF 6 OFF——No automatic close function.

Adjusting knob

Adjust the sensitivity of meet obstacle: clockwise adjusting VR1 can reduce sensitivity of obstacle of
the motor 1; clockwise adjusting VR2 can reduce sensitivity of obstacle of the motor 2.

Infrared connection

Infrared photocell function: In the closing process, when infrared ray of the infrared sensor is

covered, the gate will open immediately, to protect user and property security.

The distance between photocell receiver and photocell emitter should be not less than 2 meters,

otherwise will affect the induction of the photocell.

If connect the infrared photocell, please remove the short connection between IR and COM on the

CN2 terminal.

16

InfraredInfrared receiverreceiver connectingconnecting

－ ＋

ComCom OutOut

SETSET NCNC

InfraredInfrared emitteremitter connectingconnecting

－ ＋

LOCKLOCK

IRIRCOMCOM+PWR+PWR

15V15V

P.SWP.SW P.SWP.SW

OPOP

CLCL

1

2

IN5408IN5408

D20D20

LED7LED7

CN2CN2 CN3CN3

CN5CN5

SENSORSENSOR

TESTTEST

Figure 19

Adjustment and operation
Remote control operation

Remote control is single button mode, one same button on the remote control to circularly control

the main engine OPEN/STOP/CLOSE/STOP.

OPENOPEN

CLOSECLOSE

STOPSTOP

A

B

C

D

Figure 20

17

Add extra remote control (remote control learning): Remove the upper cover of main engine;
press the learning button S1 on the control board, and indicator light LEARN will flash once and
then go out; press the same button on the remote control twice, the LEARN flashes repeatedly and
then goes out; remote control learning is succeed. At most 25 remote controls can be learned.
Delete remote control: Delete remote control that have been learned; press the learning button
S1 and LEARN will be on; loosen the button until LEARN is off. This indicates that all remote
controls that learned previously have been deleted.

Note: Unlock the door opener, move the door to the middle position, reversely rotate the manual
release bar to lock, electrify and then press TEST button after relay restoration, the door would
automatically operate once, LED4 LED6 on the control panel is the door-opening indicator light that
shows green; LED3 LED6 is the door-closing indicator light that shows red. If the opening-closing
direction is incorrect, the direct-current motor wire could be exchanged to alter the moving direction
of the electrical machine.

Battery connection:

ACACFUSEFUSE

D12D12D13D13

LED1LED1

U1U1

C3C3

78157815

10A10A

U5U5

POWERPOWER

ACAC

78127812

MOTOR1MOTOR1 MOTOR2MOTOR2

VR1VR1 VR2VR2

D14D14

6A106A10

FUSEFUSE

8A8A

LM317LM317U6U6

15A15A

RX1RX1

F1F1

+BATTERY-+BATTERY-

REVREV

StorageStorage batterybattery

Figure 21

18

SolarSolar

panelpanel

Solar panel connection:

ACACFUSEFUSE

D12D12D13D13

LED1LED1

U1U1

C3C3

78157815

10A10A

U5U5

POWERPOWER

ACAC

78127812

MOTOR1MOTOR1 MOTOR2MOTOR2

VR1VR1 VR2VR2

D14D14

6A106A10

FUSEFUSE

8A8A

LM317LM317U6U6

SolarSolar chargercharger

CHARGECHARGE LOADLOAD

＋ － ＋ － ＋ －

BATTERYBATTERY

15A15A

RX1RX1

F1F1

+BATTERY-+BATTERY-

REVR EV

StorageStorage batterybattery

－

－

＋

＋

Figure 22

5. Others

5.1 Maintenance

Check whether the gate operates normally every month.
For the sake of safety, each gate is suggested to be equipped with infrared protector, and regular
inspection is required.
Before installation and operation of the gate opener, please read all instructions carefully.
Our company has the right to change the instruction without prior notice.

19

transformer power is normal,

5.2 Troubleshooting

Problems Possible Reasons Solutions

The gate cannot open
or close normally, and
LED does not light.

The gate can open but
cannot close.

Remote control
doesn’t work.

Press OPEN, CLOSE
button, the gate is not
moving, motor has
noise.

1.The power is off.

2.Fuse is burned.

3.Control board power wiring
with problem.

1.Photocell wiring with problem.

2.Photocell mounting with
problem.

3.Photocell is blocked by
objects.

4.Sensitivity of obstacle is too
high.

1.Battery level of the remote
control is low.

2.Remote control learning is not
completed.

Gate moving is not smoothly.

1.Switch on the power
supply.

2.Check the fuse, change the
fuse if burnt.

3.Re wiring according to
instructions.

1.If not connect photocell,
please make sure that the IR
and COM short circuit; if
connect infrared sensor,
please make sure the wiring
is correct and the photocell is
N.C.

2.Make sure that the
photocell mounting position
can be mutually aligned.

3.Remove the obstacle.

4.Reduce the sensitivity of
obstacle.

1.Change the remote control
battery.

2.Re-conduct remote control
learning.

According to the actual
situation to adjust the motor
or the gate.

Leakage switch
tripped.

Remote control
working distance is too
short.

The gate moves to the
middle position to stop
or reverse.

Power supply line short circuit or
motor line short circuit.

Signal is blocked.

1.Motor output force is not
enough.

2.Sensitivity of obstacle is too
high.

3.Gate meets obstacle.

Check wiring.

Connect external receiver
antenna, 1.5 meters above
ground.

1.Check whether the

if not, change the
transformer.

2.Adjust the VR1, VR2.

3.Remove the obstacle.