Page 1
The product, accessories and other drawings in the manual are schematic diagrams
for reference only. Due to product updates and upgrades, the actual product and
the schematic may differ slightly, please refer to the actual product. If you
have any questions, please contact customer service.
Precautions for installation
(please read carefully before installation)
1
For the large size of this product, please try to assist 2 people during installation.
2
Please confirm the quantity of each component carefully before installation.
3
In order to protect the floor, please install it on a soft floor or a soft cloth.
4
To avoid injury during installation, it is recommended that you wear gloves.
5
Please note that once the Cylinder is installed, it is difficult to remove it. If you
need to disassemble, please tap the head of the Cylinder with a rubber-headed hammer
several times, and then remove the base. Then use the principle of vibration to
continue to gently tap the base. Therefore, you need to use tools to complete it, so
please be careful not to get injured.
(The product damage and accidents caused by this operation are not covered by the
product guarantee, please be careful)
AF055
Backrest×1 Seat cushion×1 Lumbar pillow×1
Armrest×2
Precautions for use
1
When cleaning, please wipe with a soft cloth.
2
Please read the instruction manual for the functional use of the product.
3
Please avoid using in damp or fire place. Please avoid direct sunlight.
4
Please do not step on the chair or use it as a ladder, there is a risk of
5
overturning.
Please note that this product is limited to one person. The use of more than
6
two people will destroy the stability of the product and have certain risks.
For your safety, it is strictly prohibited to disassemble the Cylinder.
Head Pillow×1 Cylinder×1
Base×1 Cover of the recliner
Tilt mechanism×1
Chair wheel×5
Rabbit ear×1 Rabbit tail×1
Cylinder Cover×1
adjuster×2
1
1 2
Page 2
03 04
Screw holes for backrest
Screw hole of cover of the
recliner adjuster
Screw holes for backrest
1
2 3 4
5
1
Spare screws（M5x16mm）x1 Spare screws（M8×20mm）×1
2
5
wrench×2
Accessories table
3
Spare screws（M8×30mm）×1 Screw for the recliner adjuster（M5x16mm）x2
01 02
Insert the chair wheel into the base
3
3 4
4
Insert the Cylinder into the base
（Note: The initial shortest state just after getting the Cylinder）
Unscrew the backrest screw and place the backrest
as shown
05 06
（Fix the bottom buckle first）
Buckle up the cover of the recliner adjuster as shown in
the figure and fix it with the recliner adjuster screw
（Note: The four backrest screws are aligned with the holes in sequence and
Fix the backrest with backrest screws
then tightened）
Place the chair as shown and unscrew the Tilt mechanism
（Note: Pay attention to the length of the Tilt mechanism screws and armrest screws）
screws and armrest screws
Page 3
07 08
11
12
Place the armrest as shown and fix it with the armrest
screws
09 10
Place the tilt mechanism on the bottom of the seat cushion as
shown in the figure and fix it with the tilt mechanism screws
Align the decorative head hoop with the head hole of
backrest and insert it gently
product instructions
Lift function
If the person is not sitting on the chair, the
chair can be raised by pressing down the lever
on the bottom right Tilt mechanism of the
cushion. A person sits in a chair, press down
the lever on the bottom right Tilt mechanism
of the cushion, and then descends.
Buckle the tail fixing leather band into the button on the
backrest
Reclining function
The person sits on the chair, the person
leans back and pulls the handle on the
right side of the cushion, the chair can
lie back, when lying at a proper angle,
release the handle to lock the backrest;
continue to move the handle up, the person
recovers Sitting back, the backrest can
rebound
Troubleshoot common problem
1
Insert the base into the Tilt mechanism hole
5
5 6
Buckle the head pillow through the eyes as shown, and
put the lumbar pillow on the seat cushion
After the installation, I found the chair leaning forward
The Tilt mechanism is reversed. Please remove the Tilt mechanism and change the
installation direction, see step 8.
2
The backrest cannot be installed
Please refer to step 3 and step 4. If you still have
problems, please contact after-sales customer
service.
Loading...