Autel Intelligent Tech 3017BTDIAG User Manual

Wireless Diagnostic Interface

WQ83017BTDIAG

Trademarks

Autel®, MaxiSysTM, MaxiDAS®, MaxiScan®, MaxiTPMS®, MaxiVideoTM, MaxiRecorderTM,
and MaxiCheckTM are trademarks of Autel Intelligent Technology Co., Ltd, registered in
China, the United States and other countries. All other marks are trademarks or
registered trademarks of their respective holders.

Copyright Information

No part of this manual may be reproduced, stored in a retrieval system or transmitted,
in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, without the prior written permission of Autel.

Disclaimer of Warranties and Limitation of Liabilities

All information, specifications and illustrations in this manual are based on the latest
information available at the time of printing. Autel reserves the right to make changes at
any time without notice. While information of this manual has been carefully checked
for accuracy, no guarantee is given to the completeness and correctness of the
contents, including but not limited to the product specifications, functions, and
illustrations.

Autel will not be liable for any direct damages or for any special, incidental, or indirect
damages or for any economic consequential damages (including lost profits).

IMORTANT: Before operating or maintaining this unit, please read this manual carefully
paying extra attention to the safety warnings and precautions.

For Services and Support:

www.maxidas.com

www.auteltech.com

1-877-288-3587/1-877-AUTELUS (North America)
0086-755-86147779 (China)

[e-mail]

For technical assistance in all other markets, please contact your local selling agent

ii

Safety Information

For your own safety and the safety of others, and to prevent damage to the equipment
and vehicles upon which it is used, it is important that the safety instructions herein
presented throughout this manual be read and understood by all persons operating, or
coming into contact with, the equipment.

There are various procedures, techniques, tools, and parts for servicing vehicles, as
well as in the skill of the individual doing the work. Because of the vast number of test
applications and variations in the products that can be tested with this instrument, we
cannot possibly anticipate or provide advice or safety messages to cover every
situation. It is the automotive technician’s responsibility to be knowledgeable of the
system being tested. It is essential to use proper service methods and test procedures.
It is important to perform tests in an appropriate and acceptable manner that does not
endanger your safety, the safety of others in the work area, the equipment being used,
or the vehicle being tested.

Before using the equipment, always refer to and follow the safety messages and
applicable test procedures provided by the manufacturer of the vehicle or equipment
being tested. Use the equipment only as described in this manual. Read, understand,
and follow all safety messages and instructions in this manual.

Safety Messages

Safety messages are provided to help prevent personal injury and equipment damage.
All safety messages are introduced by a signal word indicating the hazard level.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury to the operator or to bystanders.

WARNING: Indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injury to the operator or to bystanders.

Safety Instructions

The safety messages herein cover situations Autel is aware of. Autel cannot know,
evaluate or advise you as to all of the possible hazards. You must be certain that any
condition or service procedure encountered do not jeopardize your personal safety.

DANGER: When an engine is operating, keep the service area WELL
VENTILATED or attach a building exhaust removal system to the engine exhaust
system. Engines produce carbon monoxide, an odorless, poisonous gas that
causes slower reaction time and can lead to serious personal injury or loss of
life.

iii

Safety Information Important Safety Insturctions

WARNINGS:

 Always perform automotive testing in a safe environment.
 Wear safety eye protection that meets ANSI standards.
 Keep clothing, hair, hands, tools, test equipment, etc. away from all

moving or hot engine parts.

 Operate the vehicle in a well ventilated work area, for exhaust gases are

poisonous.

 Put the transmission in PARK (for automatic transmission) or NEUTRAL

(for manual transmission) and make sure the parking brake is engaged.

 Put blocks in front of the drive wheels and never leave the vehicle

unattended while testing.

 Use extreme caution when working around the ignition coil, distributor cap,

ignition wires and spark plugs. These components create hazardous
voltages when the engine is running.

 Keep a fire extinguisher suitable for gasoline, chemical, and electrical fires

nearby.

 Do not connect or disconnect any test equipment while the ignition is on or

the engine is running.

 Keep the test equipment dry, clean, free from oil, water or grease. Use a

mild detergent on a clean cloth to clean the outside of the equipment as
necessary.

 Do not drive the vehicle and operate the test equipment at the same time.

Any distraction may cause an accident.

 Refer to the service manual for the vehicle being serviced and adhere to

all diagnostic procedures and precautions. Failure to do so may result in
personal injury or damage to the test equipment.

 To avoid damaging the test equipment or generating false data, make

sure the vehicle battery is fully charged and the connection to the vehicle
DLC is clean and secure.

 Do not place the test equipment on the distributor of the vehicle. Strong

electro-magnetic interference can damage the equipment.

iv

Contents

SAFETY INFORMATION ........................................................................................... III

CHAPTER 1 USING THIS MANUAL ...................................................................... 1

1.1 CONVENTIONS .................................................................................................... 1

1.1.1 Bold Text .................................................................................................. 1

1.1.2 Notes and Important Messages .............................................................. 1

1.1.3 Hyperlinks ................................................................................................ 1

1.1.4 Procedures ............................................................................................... 1

CHAPTER 2 INTRODUCTION ............................................................................... 3

2.1 MAXISYS DISPLAY TABLET ..................................................................................... 3

2.1.1 Functional Description ............................................................................. 3

2.1.2 Power Sources ......................................................................................... 5

2.1.3 Technical Specifications ........................................................................... 6

2.2 VCI – BLUETOOTH DIAGNOSTIC INTERFACE .............................................................. 7

2.2.1 Functional Description ............................................................................. 7

2.2.2 Technical Specifications ........................................................................... 8

2.2.3 Power Sources ......................................................................................... 8

2.3 VCI – J2534 ECU PROGRAMMING DEVICE ............................................................. 8

2.3.1 Functional Description ............................................................................. 8

2.3.2 Power Sources ....................................................................................... 10

2.3.3 Technical Specifications......................................................................... 10

2.4 ACCESSORY KIT ................................................................................................. 11

2.4.1 Main Cable ............................................................................................ 11

2.4.2 OBD-I Adapters ...................................................................................... 11

2.4.3 Other Accessories .................................................................................. 12

CHAPTER 3 GETTING STARTED ......................................................................... 14

3.1 POWERING UP .................................................................................................. 14

3.1.1 Application Buttons ............................................................................... 15

3.1.2 Locator and Navigation Buttons ............................................................ 16

3.1.3 System Status Icons ............................................................................... 17

3.2 POWERING DOWN ............................................................................................ 17

3.2.1 Reboot System ....................................................................................... 18

3.3 INSTALL COMPUTER SOFTWARE ............................................................................ 18

3.3.1 Printing Operation ................................................................................. 19

CHAPTER 4 DIAGNOSTICS OPERATIONS ........................................................... 20

4.1 VEHICLE CONNECTION ........................................................................................ 20

v

Safety Information Important Safety Insturctions

4.1.1 No Communication Message ................................................................ 22

4.2 GETTING STARTED ............................................................................................. 22

4.2.1 Vehicle Menu Layout ............................................................................. 23

4.3 VEHICLE IDENTIFICATION ..................................................................................... 24

4.3.1 Auto VIN Scan ........................................................................................ 25

4.3.2 Manual VIN Input .................................................................................. 25

4.3.3 Manual Vehicle Selection ...................................................................... 26

4.3.4 Alternative Vehicle Identification .......................................................... 29

4.4 NAVIGATION ..................................................................................................... 29

4.4.1 Diagnostics Screen Layout ..................................................................... 29

4.4.2 Screen Messages ................................................................................... 32

4.4.3 Making Selections ................................................................................. 33

4.5 OPERATIONS..................................................................................................... 33

4.5.1 Diagnosis ............................................................................................... 34

4.5.2 ECU Information .................................................................................... 38

4.5.3 Read Codes ............................................................................................ 38

4.5.4 Erase Codes ........................................................................................... 39

4.5.5 Live Data................................................................................................ 40

4.5.6 Active Test ............................................................................................. 46

4.5.7 Programming and Coding ..................................................................... 47

4.6 GENERIC OBD II OPERATIONS ............................................................................. 51

4.6.1 General Procedure ................................................................................. 51

4.6.2 Function Descriptions ............................................................................ 53

4.7 EXITING DIAGNOSTICS ........................................................................................ 56

CHAPTER 5 DATA MANAGER OPERATIONS ....................................................... 57

5.1 OPERATIONS..................................................................................................... 57

5.1.1 Image Files ............................................................................................ 57

5.1.2 PDF Files ................................................................................................ 59

5.1.3 Review Data .......................................................................................... 60

5.1.4 Apps Manager (Coming soon) ............................................................... 60

5.1.5 Message (Coming soon) ........................................................................ 61

5.1.6 Data Logging (Coming soon) ................................................................. 61

CHAPTER 6 MAXICLOUD OPERATIONS ............................................................. 62

6.1 NAVIGATION ..................................................................................................... 62

6.1.1 Terminology ........................................................................................... 64

6.2 OPERATIONS..................................................................................................... 65

6.2.1 Home ..................................................................................................... 65

6.2.2 My Cloud ............................................................................................... 66

6.2.3 Search Fix .............................................................................................. 68

vi

Safety Information Important Safety Insturctions

6.2.4 Q&A ....................................................................................................... 69

6.2.5 Support .................................................................................................. 69

CHAPTER 7 SETTINGS OPERATIONS ................................................................. 70

7.1 OPERATIONS..................................................................................................... 70

7.1.1 Unit ........................................................................................................ 70

7.1.2 Language ............................................................................................... 70

7.1.3 Printing Setting ...................................................................................... 71

7.1.4 Wired Network ...................................................................................... 71

7.1.5 Push Message ........................................................................................ 72

7.1.6 About ..................................................................................................... 73

7.1.7 System Settings ..................................................................................... 73

CHAPTER 8 SHOP MANAGER OPERATIONS ...................................................... 74

8.1 VEHICLE HISTORY .............................................................................................. 74

8.1.1 Historical Test Record ............................................................................ 76

8.2 WORKSHOP INFORMATION .................................................................................. 77

8.3 CUSTOMER MANAGER ....................................................................................... 78

CHAPTER 9 UPDATE OPERATION ...................................................................... 82

CHAPTER 10 VCI MANAGER OPERATIONS .......................................................... 84

10.1 BLUETOOTH PAIRING ...................................................................................... 85

10.2 WIRED NETWORK CONNECTION ....................................................................... 86

CHAPTER 11 REMOTE DESK OPERATIONS .......................................................... 88

11.1 OPERATIONS ................................................................................................. 88

CHAPTER 12 SUPPORT OPERATIONS .................................................................. 90

12.1 PRODUCT REGISTRATION ................................................................................. 90

12.2 SUPPORT SCREEN LAYOUT ............................................................................... 91

12.3 MY ACCOUNT ............................................................................................... 92

12.4 USER COMPLAINT .......................................................................................... 92

12.5 SUPPORT COMMUNITIES ................................................................................. 95

12.6 TRAINING CHANNELS ...................................................................................... 97

12.7 FAQ DATABASE ............................................................................................. 98

CHAPTER 13 REMOTE PROGRAM OPERATIONS (COMING SOON) ...................... 99

CHAPTER 14 TRAINING OPERATIONS ................................................................. 99

CHAPTER 15 QUICK LINK OPERATIONS .............................................................101

vii

Safety Information Important Safety Insturctions

CHAPTER 16 DIGITAL INSPECTION OPERATIONS ...............................................102

16.1 ADDITIONAL ACCESSORIES ............................................................................. 103

16.2 OPERATIONS ............................................................................................... 105

CHAPTER 17 SCOPE OPERATIONS (COMING SOON) ..........................................107

CHAPTER 18 MAINTENANCE AND SERVICE .......................................................108

18.1 MAINTENANCE INSTRUCTIONS........................................................................ 108

18.2 TROUBLESHOOTING CHECKLIST ....................................................................... 109

18.3 ABOUT BATTERY USAGE ................................................................................ 109

18.4 SERVICE PROCEDURES ................................................................................... 110

CHAPTER 19 WARRANTY ..................................................................................112

viii

Chapter 1 Using This Manual

This manual contains tool usage instructions.
Some illustrations shown in this manual may contain modules and optional equipment

that are not included on your system. Contact your sales representative for availability
of other modules and optional equipment.

1.1 Conventions

The following conventions are used.

1.1.1 Bold Text

Bold emphasis is used to highlight selectable items such as buttons and menu
options.

Example:

 Tap OK.

1.1.2 Notes and Important Messages

The following messages are used.

Notes

A NOTE provides helpful information such as additional explanations, tips,
and comments.

Important

IMPORTANT indicates a situation which, if not avoided, may result in damage

to the test equipment or vehicle.

1.1.3 Hyperlinks

Hyperlinks, or links, that take you to other related articles, procedures, and
illustrations are available in electronic documents. Blue colored text indicates
a selectable hyperlink.

1.1.4 Procedures

An arrow icon indicates a procedure.

1

Using This Manual Conventions

Example:

 To use the camera:

1 Tap the Camera button. The camera screen opens.
2 Focus the image to be captured in the view finder.
3 Tap the blue circle. The view finder now shows the captured picture

and auto-saves the taken photo.

2

Chapter 2 Introduction

The MaxiSysTM Diagnostic Platform is an evolutionary smart solution for specialized
automotive diagnosis. Utilizing the powerful A9 quad-core 1.40GHz processor, and a

9.7 inch LED capacitive touch screen, combined with the best possible coverage of
OE-level diagnostics, and based on the revolutionary multitask-capable Android
Operating system, the MaxiSys organizes information with test instrumentation to help
you diagnose symptoms, codes, and customer complaints easily, quickly and
efficiently.

There are two main components to the MaxiSys system:

 MaxiSys Display Tablet -- the central processor and monitor for the system
 Vehicle Communication Interface (VCI) -- the device for accessing vehicle data

NOTE: Autel provides two optional VCI devices for your choice. One is the J2534
Programming Device; the other is the Bluetooth Diagnostic Interface, both will be
introduced in this chapter.

This manual describes the construction and operation of these devices and how they
work together to deliver diagnostic solutions.

2.1 MaxiSys Display Tablet

2.1.1 Functional Description

Figure 2-1 MaxiSys Front View

1. 9.7” LED Capacitive Touch Screen

2. Ambient Light Sensor – detects ambient brightness

3. Microphone
3

Introduction MaxiSys Display Tablet

Figure 2-2 MaxiSys Back View

1. Audio Speaker

2. Collapsible Stand – extends from the back to allow hands-free viewing of

the display tablet at a 30 degree angle

3. Camera Lens

4. Camera Flash

Figure 2-3 MaxiSys Left Side

1. SIM (subscriber identity module ) Card Slot

2. Mini SD (secure digital) Card Slot

3. Mini USB (universal serial bus) OTG Port

4. Head Phone Jack

4

Introduction MaxiSys Display Tablet

Figure 2-4 MaxiSys Top View

1. DC Power Supply Input Port

2. Ethernet Port

3. HDMI (high-definition multimedia interface) Port

4. USB Port

5. VGA (video graphics array) Port

6. Lock/Power Button – turns the MaxiSys tool on and off with long press, or

locks the screen with short press

2.1.2 Power Sources

The MaxiSys Display Tablet can receive power from any of the following
sources:

 Internal Battery Pack
 AC/DC Power Supply
 Vehicle Power

Internal Battery Pack

The display tablet can be powered with the internal rechargeable battery,
which if fully charged can provide sufficient power for about 6.5 hours of
continuous operation.

AC/DC Power Supply

The display tablet can be powered from a wall socket using the AC/DC power
adapter. The AC/DC power supply also charges the internal battery pack.

Vehicle Power

The display tablet can be powered from the cigarette lighter or other suitable
power port on the test vehicle through a direct cable connection. The vehicle
power cable connects to the DC power supply port on the top side of the
display unit.

5

Introduction MaxiSys Display Tablet

Item

Description

Operating System

Android

TM

4.0, Ice Cream Sandwich

Processor

Samsung Exynos Quad-Core Processor 1.4GHz

Memory

2GB RAM & 32GB On-board Memory

Display

9.7 inch LED capacitive touch screen with
1024x768P resolution

Connectivity

 Ethernet: RJ45 Ethernet Connection
 Cellular: 3G/4G module: WCDMA<E
 Wi-Fi (802.11 a/b/g/n)
 USB: 2.0
 Bluetooth v.2.1 + EDR

Camera (rear)

Rear-facing, 5.0 Megapixel, AF with Flashlight

Sensors

Gravity Accelerometer, Ambient Light Sensor
(ALS)

Audio Input/Output

 Microphone
 Dual Speakers
 4-Band 3.5 mm stereotype/standard headset

jack

Power and Battery

 11000 mAh 3.7 V lithium-polymer battery
 Charging via 12 V AC/DC power supply

Input Voltage

12 V (9-24 V)

Power Consumption

6.5 W

Operating
Temperature

-10 to 55°C (14 to 131°F)

Storage Temperature

-20 to 70°C (-4 to 158°F)

Housing

Strong plastic housing with protective rubber boot

Dimensions (W x H x D)

300 mm (11.81”) x 220 mm (8.66”) x 50 mm (1.97”)

Weight

NW: 1.42 kg (3.13 lb), MaxiSys GW: 8.655 kg
(19.08 lb); MaxiSys Pro GW: 8.052 kg (17.75 lb)

Protocols

ISO 9142-2, ISO 14230-2, ISO 15765-4, K/L lins,
Flashing Code, SAE-J1850 VPW, SAE-J1850
PWM, CAN ISO 11898, Highspeed, Middlespeed,
Lowspeed and Singlewire CAN, GM UART, UART
Echo Byte Protocol, Honda Diag-H Protocol, TP

2.0, TP 1.6, SAE J1939, SAE J1708,
Fault-Tolerant CAN

2.1.3 Technical Specifications

6

Introduction VCI – Bluetooth Diagnostic Interface

2.2 VCI – Bluetooth Diagnostic Interface

2.2.1 Functional Description

Figure 2-5 Bluetooth Diagnostic Interface

1. Vehicle Data Connector (DB15-Pin)

2. Power LED - illuminates solid green when powered on

3. Vehicle LED - flashes green when communicating with the vehicle’s

network

4. Error LED - illuminates solid red when serious hardware failure occurs;

also flashes red when performing software/firmware update

5. Bluetooth LED - illuminates solid green when connected with the

MaxiSys display tablet through Bluetooth communication; also flashes
green when transmitting data between the vehicle and the display tablet

6. USB LED – illuminates solid green when the device is properly

connected and communicating with the MaxiSys display tablet via the
USB cable

7. USB Port

Communication

The Bluetooth Diagnostic Interface supports both Bluetooth and USB
communication. It can transmit vehicle data to the MaxiSys Display Tablet with
or without a physical connection. The working range of the transmitter through
Bluetooth communication is about 980 feet (about 300 m). A signal lost due to
moving out of range automatically restores itself when the display unit is
brought closer to the VCI unit.

7

Introduction VCI – J2534 ECU Programming Device

Item

Description

Communications

 Bluetooth V.2.1 + EDR
 USB 2.0

Wireless Frequency

2.4 GHz

Input Voltage Range

Supply Current

Operating Temperature

0°C to 50°C (ambient)

Storage Temperature

-20°C to 70°C (ambient)

Dimensions (L x W x H)

147.5 mm (5.80”) x 85.5 mm (3.37”) x 29.0 mm
(1.14”)

Weight

0.215 kg (0.473 lb)

2.2.2 Technical Specifications

12 VDC
300 mA @ 12 VDC

2.2.3 Power Sources

The Bluetooth Diagnostic Interface operates on 12-volt vehicle power, which it
receives through the vehicle data connection port. The unit powers on
whenever it is connected to an OBD II/EOBD compliant data link connector
(DLC).

2.3 VCI – J2534 ECU Programming Device

2.3.1 Functional Description

Figure 2-6 J2534 ECU Programming Device

8

Introduction VCI – J2534 ECU Programming Device

1. Ethernet Port

2. USB Port

3. Power LED - illuminates solid green when powered on

4. Error LED - illuminates solid red when serious hardware failure occurs

5. Bluetooth LED - illuminates solid green when connected with the

MaxiSys display tablet through Bluetooth communication

6. Ethernet LED - illuminates solid green when connected with the MaxiSys

display tablet or an existing LAN via the Ethernet serial cable

7. USB Status Light -- illuminates solid green when the device is properly

connected and communicating with the MaxiSys display tablet or the PC
via the USB cable

8. Vehicle LED - flashes green when communicating with the vehicle’s

network

IMPORTANT: Do not disconnect the reprogramming device while this status
light is on! If the flash reprogramming procedure is interrupted while the
vehicle’s ECU is blank or only partially programmed, the module may be
unrecoverable.

9. Bluetooth Antenna

10. DC Power Supply Input Port

11. Vehicle Data Connector (DB26-Pin MVCI)

12. External Programming Voltage Output Port

13. A/D Input Port

J2534 Reprogramming Capability

The J2534 ECU Programming Device is a SAE J2534-1 & -2 compliant
PassThru reprogramming interface device. Using the updated OEM software,
it is capable of replacing the existing software/firmware in the Electronic
Control Units (ECU), programming new ECUs and fixing software-controlled
drivability issues and emission issues.

Communication

The J2534 ECU programming device supports Bluetooth, Ethernet and USB
communication. It can transmit vehicle data to the MaxiSys display tablet with
or without a physical connection. The working range of the transmitter through
Bluetooth communication is 980 feet (about 300 m). A signal lost due to
moving out of range automatically restores itself when the display tablet unit is
brought closer to the VCI unit.

9

Introduction VCI – J2534 ECU Programming Device

Item

Description

Communications

 Ethernet: RJ45 Ethernet connection
 Bluetooth
 USB 2.0

Input Voltage Range

6 VDC to 26 VDC

Supply Current

300 mA @ 6 VDC
200 mA @ 12 VDC
110 mA @ 24 VDC

Operating Temperature

0°C to +60°C (ambient)

Storage Temperature

-65°C to +100°C (ambient)

Dimensions (L x W x H)

183.8mm (7.23”) x 135.5mm (5.33”) x 41mm
(1.6”)

Weight

0.54 kg (1.20 lb)

2.3.2 Power Sources

The J2534 programming device can receive power from both of the following
sources:

 Vehicle Power
 AC/DC Power Supply

Vehicle Power

The J2534 programming device operates on 12-volt vehicle power, which it
receives through the vehicle data connection port. The device powers on
whenever it is connected to an OBD II/EOBD compliant data link connector
(DLC). For non OBD II/EOBD compliant vehicles, the device can be powered
from a cigarette lighter or other suitable power port on the test vehicle using
the auxiliary power cable.

AC/DC Power Supply

The J2534 programming device can be powered from a wall socket using the
AC/DC power adapter.

2.3.3 Technical Specifications

NOTE: For additional information please refer to the accompanied user

manual for the J2534 ECU Programming Device.

10

Introduction Accessory Kit

Benz-14

Chrysler-16

BMW-20

Kia-20

Nissan-14

GM/Daewoo-12

Honda-3

Fiat-3

2.4 Accessory Kit

2.4.1 Main Cable

The VCI device can be powered through the Main Cable when connected to
an OBD II/EOBD compliant vehicle. The Main Cable connects the VCI device
to the vehicle’s data link connector (DLC), through which the VCI device can
transmit vehicle data to the MaxiSys display tablet.

Figure 2-7 Main Cable
Length = 1.9 m for J2534 Programming Device
Length = 1.2 m for Bluetooth Diagnostic Interface

2.4.2 OBD I Adapters

The OBD I adapters are for Non-OBD II vehicles. The adapters used depend
on the type of vehicle make being tested. The most common adapters are
shown below.

11

Introduction Accessory Kit

PSA-2

Benz-38

VW/Audi-2+2

Chang’an-3

Mitsubishi/Hyun

dai -12+16

Standard 2.0 USB Cable

Connects the display tablet to the VCI unit.

Mini USB Cable

Connects the display tablet to the PC.

AC/DC External Power Adapter

Connects the display tablet to the external DC power
port for power supply.

Compact Disc (CD)

Includes the User Manual, Remote Desktop, Printing
Services Program and Update Application, etc.

Stylus Pen

Provides precise touch and control, while protecting
your touch screen from scratching.

Ethernet Serial Cable

Connects the display tablet to the VCI unit (for J2534
Programming Device only).

2.4.3 Other Accessories

12

Introduction Accessory Kit

Cigarette Lighter

Provides power to the display tablet or the J2534
programming device through connection to the
vehicle’s cigarette lighter receptacle, as some
non-OBD II vehicles cannot provide power via the
DLC connection.

Clipper Cable

Provides power to the display tablet or the J2534
programming device, through connection to the
vehicle’s battery (for J2534 Programming Device
only).

13

Chapter 3 Getting Started

Make sure the MaxiSysTM Display Tablet has a charged battery or is connected to the
DC power supply (see 2.1.2 Power Sources on page 5).

3.1 Powering Up

Press the Power Button on the top right side of the Display Tablet to switch the
unit on. The system boots up, and shows the lock screen. Press and drag the
inner ring to the edge of the circle to unlock the screen; the MaxiSys Job Menu
is shown.

Figure 3-1 Sample MaxiSys Job Menu

1. Application Buttons

2. Locator and Navigation Buttons

3. Status Icons
NOTE: The screen is locked by default when you first turn on the display tablet.

It is recommended to lock the screen to protect information in the system and
reduce battery usage.

Almost all operations on the display tablet are controlled through the touch
screen. The touch screen navigation is menu driven, which allows you to
quickly locate the test procedure, or data that you need through a series of
choices and questions. Detailed descriptions of the menu structures are found
in the chapters for the various applications.

14

Getting Started Powering Up

Name

Button

Description

Diagnostics

Configures the unit to operate as a diagnostic
tool. See Diagnostics Operations on page 20.

Data
Manager

Opens the organization system for saved data
files. See Data Manager Operations on page 57。

MaxiCloud

Launches the MaxiCloud platform which provides
the most compatible and abundant repair
techniques and diagnostics database. See

MaxiCloud Operations on page 62.

Settings

Allows you to set the system settings, and to view
the general information about the Display Tablet.
See Settings Operations on page 70.

Shop
Manager

Allows you to edit and save workshop information
and customer data, as well as reviewing test
vehicle history records. See Shop Manager

Operations on page 74.

Update

Checks for latest update available for the system,
and perform updating procedures. See Update

Operation on page 82.

VCI
Manager

Establishes and manages Bluetooth or wired
connections to the VCI device. See VCI Manager

Operations on page 84.

Remote
Desk

Configures your unit to receive remote support
using the TeamViewer application program. See

Remote Desk Operations on page 88.

Support

Launches the Support platform which
synchronizes Autel’s on-line service base station
with the MaxiSys tablet. See Support Operations
on page 90.

3.1.1 Application Buttons

The Application Buttons configure the MaxiSys for the type of operation or
activity to be performed. The table below gives brief descriptions of the
available applications.

Use the stylus pen or your finger tip to select an application from the Job
Menu.

Table 3-1 Applications

15

Getting Started Powering Up

Name

Button

Description

Remote
Program

Configures your unit to operates as a PassThru
interface to allow remote control for vehicle
diagnosis and ECU reprogramming. See Remote

Program Operations (Coming soon) on page 99.

Training

Allows you to store and play useful technical
tutorial videos for the device usage or vehicle
repair and maintenance techniques, etc. See

Training Operations on page 99.

Quick Link

Provides associated website bookmarks to allow
quick access for product update, service, support
and other information. See Quick Link Operations
on page 101.

Digital
Inspection

Configures the unit to operate as a video scope
device by connecting to an Imager head cable for
close vehicle inspections. See Digital Inspection

Operations on page 102.

Scope

Configures the unit to operate as a lab scope,
graphing multimeter, or digital multimeter. See

Scope Operations (Coming soon) on page 107.

Name

Button

Description

Locator

Indicates the location of the screen. Swipe the
screen left or right to view the previous or next
screen.

Back

Returns to the previous screen.

Home

Returns to Android System’s Home screen.

Recent Apps

Displays a list of applications that are currently
working. To open an app, touch it. To remove
an app, swipe it to the right.

3.1.2 Locator and Navigation Buttons

Operations of the Navigation Buttons at the bottom of the screen are
described in the table below:

Table 3-2 Locator and Navigation Buttons

16

Getting Started Powering Down

Name

Button

Description

Chrome

Launches the Chrome browser.

Camera

Opens the camera.

Display & Sound

Allows you to adjust the brightness of the
screen and the volume of the audio output.

VCI Manager

Opens the VCI Manager application. The tick
icon at the bottom right corner indicates the
display tablet is communicating with the VCI
device, otherwise a cross icon displays.

MaxiSys
Shortcut

Returns to the MaxiSys Job Menu or
diagnostic interface.

 To use the camera:

1. Tap the Camera button. The camera screen opens.

2. Focus the image to be captured in the view finder.

3. Tap the blue circle. The view finder now shows the captured picture
and auto-saves the taken photo.

4. Tap the thumbnail image on the top right corner of the screen to view
the stored images.

5. Tap the Back or Home button to exit the camera application.

Refer to Android documentation for additional information.

3.1.3 System Status Icons

These are the standard status icons of the Android Operating system. Your
MaxiSys display tablet is a fully functional Android Pad. Refer to Android
documentation for additional information.

3.2 Powering Down

All vehicle communication must be terminated before shutting down the
MaxiSys display tablet. A warning message displays if you attempt to shut
down while the VCI unit is communicating with the vehicle. Forcing a shut
down while communicating may lead to ECM problems on some vehicles. Exit
the Diagnostic application before powering down.

17

Getting Started Install Computer Software

 To power down the MaxiSys tablet:

1. Press and hold the Lock/Power Button.

2. Tap OK; the tablet will turn off in a few seconds.

3.2.1 Reboot System

In case of system crash, press and hold the Lock/Power button for 8 seconds
to reboot the system.

3.3 Install Computer Software

The MaxiSys
a computer to enhance capabilities and improve user experience. To realize
these functions on a computer, you need to install certain software.

There are two Setup.exe program packages contained in the CD provided
with the MaxiSys tool kit. The packages include the following applications:

1. Remote Control – launches a remote control application which allows
you to take a view or control of the MaxiSys tablet remotely from the
computer via the Internet connection

2. PC Link – launches a printer interface which receives and allows editing
the files sent from the MaxiSys tablet for printing

TM

diagnostic device allows you to realize some of its functions on

3. Setup Driver for the VCI device

4. Firmware Update Agent for the VCI device

 To install the Setup.exe program

1. Insert the CD into the CD-ROM of the computer. The driver
installation wizard will load momentarily.

2. Click on Next on the welcome page.

3. Click the Change button, and select a destination folder to install the
program, and click Next to continue. Or directly click Next to
continue without changing the default installation folder.

4. Click Install and the Setup.exe program will be installed onto the
computer.

18

Getting Started Install Computer Software

3.3.1 Printing Operation

This section describes how to receive file from the MaxiSys tablet and perform
printing through the computer:

 To perform printing through the computer

1. Install the PC Link (the printer interface program) to the computer.

2. Make sure the display tablet is connected to the computer network,
either via Wi-Fi or LAN, before printing. See 7.1.3 Printing Setting on
page 71 for more information.

3. Run the printer interface program on the computer.

4. Tap the Print button on the toolbar displayed in various applications
on the MaxiSys display tablet. A temporary file will be created and
send to the computer for printing.

5. Click the Printer Server tab on the top of the printer interface, and
wait for the printing file to load.

6. Click the Print button on the printer interface to start printing.

NOTE: Make sure the computer installed with the printer interface program is
connected to a printer.

19

Chapter 4 Diagnostics Operations

By establishing a data link to the electronic control systems of the vehicle being
serviced through the VCI device, the Diagnostics application allows you to retrieve
diagnostic information, view live data parameters, and perform active tests. The
Diagnostics application can access the electronic control module (ECM) for various
vehicle control systems, such as engine, transmission, antilock brake system (ABS),
airbag system (SRS) and more.

4.1 Vehicle Connection

The Diagnostics operations require connecting the MaxiSysTM Diagnostic
Platform to the test vehicle using the main cable, and test adapters (for
non-OBD II vehicles). The method used to connect the VCI device to a
vehicle’s DLC depends on the vehicle’s configuration as follows:

 A vehicle equipped with an On-Board Diagnostics Two (OBD II)

management system supplies both communication and 12-volt power
through a standardized J-1962 DLC.

 A vehicle not equipped with an OBD II management system supplies

communication through a DLC connection, and in some cases supplies
12-volt power through the cigarette lighter receptacle or a connection to
the vehicle battery.

OBD II Vehicle Connection

This type of connection only requires the main cable without any additional
adapter.

 To connect to an OBD II vehicle

1. Connect the main cable’s female adapter to the Vehicle Data
Connector on the VCI device, and tighten the captive screws.

2. Connect the cable’s 16-pin male adapter to the vehicle’s DLC, which
is generally located under the vehicle dash.

NOTE: The vehicle’s DLC is not always located under the dash; refer to the
user manual of the test vehicle for additional connection information.

Non-OBD II Vehicle Connection

This type of connection requires both the main cable and a required OBD I
adapter for the specific vehicle being serviced.

20

Diagnostics Operations Vehicle Connection

There are three possible conditions for Non-OBD II vehicle connection:

 DLC connection supplies both communication and power.
 DLC connection supplies communication and power is to be supplied via

the cigarette lighter connection.

 DLC connection supplies communication and power is to be supplied via

connection to the vehicle battery.

 To connect to a Non-OBD II Vehicle

1. Locate the required OBD I adapter and connect its 16-pin jack to the
main cable’s male adapter.

2. Connect the main cable’s female adapter to the Vehicle Data
Connector on the VCI device, and tighten the captive screws.

3. Connect the attached OBD I adapter to the vehicle’s DLC.

NOTE: Some adapters may have more than one adapter or may have test
leads instead of an adapter. Whatever the case, make the proper connection
to the vehicle’s DLC as required.

 To connect the cigarette lighter - for J2534 ECU Programming Device

only

1. Plug the DC power connector of the cigarette lighter into the J2534
programming device.

2. Connect the male connector of the cigarette lighter into the vehicle’s
cigarette lighter receptacle.

 To connect the clipper cable - for J2534 ECU Programming Device

only

1. Connects the tubular plug of the clipper cable to the male connector
of the cigarette lighter.

Figure 4-1 Connection between Cigarette Lighter and Clipper Cable

21

Diagnostics Operations Getting Started

2. Plug the DC power connector of the cigarette lighter into the J2534
programming device.

3. Connect the clipper cable to the vehicle’s battery.

4.1.1 No Communication Message

A. If the MaxiSys Display Tablet is not connected to the VCI device, an

“Error” message displays. An “Error” message indicates the display
tablet is not communicating with the VCI device, and so cannot gain
access to the vehicle control module. In this case, you need to do the
following check-ups:

 Check if the VCI device is powered on.
 Check the cable connection between the display tablet and the VCI

device.

 In case of wireless connection, check that the network is configured

correctly.

B. If the VCI device is unable to establish a communication link, a prompt

message displays with check instructions. The following conditions are
the possible causes for this massage to display:

 The VCI device is unable to establish a communication link with the

vehicle.

 You’ve selected a system for testing that the vehicle is not equipped

with.

 There is a loose connection.
 There is a blown vehicle fuse.
 There is a wiring fault on the vehicle, or the data cable or adapter.
 There is a circuit fault in the data cable or adapter.
 Incorrect vehicle identification was entered.

4.2 Getting Started

Prior to first use of the Diagnostics application, the VCI device must be
synchronized with the MaxiSys Display Tablet to establish a communication
link. See VCI Manager Operations on page 84.

22