Page 1
INSTALLATION AND OPERATION MANUAL
XDS SERIES
Page 2
IMPORTANT SAFETY INFORMATION
PRÉCAUTIONS DURANT UTILISATION
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
9. Only use attachments/accessories specified by the manufacturer.
10. Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-over.
11. Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled or objects have fallen into
the apparatus, the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.
12. This appliance shall not be exposed to dripping or splashing water and
that no object filled with liquid such as vases shall be placed on the
apparatus.
13. The mains plug is used as the disconnect device and shall remain
readily accessible. If the mains plug is not readily accessible due to
mounting in a 19” rack, then the mains plug for the entire rack must
be readily accessible.
14. WARNING: To reduce the risk of fire or electric shock, do not expose this
apparatus to rain or moisture.
1. LISEZ ces instructions.
2. Tenez ces instructions.
3. Notez tous les avertissements.
4. Suivez toutes les avertissements.
5. N’utilisez pas ce produit près de l’eau (la piscine, la plage, le lac, etc.).
6. Nettoyez seulement avec une étoffe sèche.
7. Ne bloquez aucuns troux de ventilation. Installez en accord avec
les instructions du manufacturier.
8. N’installez près aucunes sources de chaleur comme radiateurs, registres
de chaleur, fours ou les autres équipements (y compris amplificateurs)
qui produisent la chaleur.
9. Seulement utilisez attachements/accessoires spécifiés par le
manufacturier.
10. Utilisez seulement avec un chariot, un stand, un trépied, un support
ou une table indiquée par le manufacturier, ou vendue avec l’appareil.
Quand un chariot est utilisé, faites attention en déplaçant la combinaison
d’appareil/chariot pour éviter de se déséquilibrer.
11. Référez au personnel qualifié de service pour toutes réparations.
La réparation est donnée quand le système a été endommagé à n’importe
façon, par exemple un fil ou une fiche endommagé(e) de la source
d’alimentation. Avoir été exposé à pluie ou humidité, n’opère pas
normalement, ou avoir été tombé.
12. L’appareil ne doit pas être exposé aux écoulements ou aux éclaboussures
et aucun objet ne contenant de liquide, tel qu’un vase, ne doit être placé
sur l’objet.
13. La prise du secteur ne doit pas être obstruée ou doit
être facilement accessible pendant son utilisation. Pour
être complètement déconnecté
de l’alimentation d’entrée, la prise doit être débranchée
du secteur.
14. AVERTISSEMENT: Pour éviter le risque d’incendie ou de
chocs électriques, ne pas exposer cet appareil à la pluie ou à l’humidité.
PAGE 2
XDS SERIES INSTALLATION AND OPERATION MANUAL
Page 3
XDS SERIES
The XDS range of speakers includes 8”, 10” and 12” models all
with high quality compression drivers and two subwoofer models
with a single 15” or dual 12”.
The XDS range of speakers is perfect for driveway or corporate hire
as well as live sound installations. With features including multi
angle enclosure design so speakers can be used for front of house
or foldback applications, terminal strip or four pole connectors,
pole mount, fly points plus a variety of bracket options and a
contemporary styling, the XDS range of speakers and subs offer the
contractor an extremely high quality speaker system with common
voicing across the range at an amazing price point.
INTRODUCTION AND CONTENTS
INTRODUCTION 3
FRONT PANEL 4
REAR PANEL 5
MOUNTING 6
ACCESSORIES 8
DIMENSIONS 9
SPECIFICATIONS 11
Revision 1.0 June 2012
XDS SERIES INSTALLATION AND OPERATION MANUAL
PAGE 3
Page 4
XDS10
2 Way Full Range Speaker
Made in China
SN:
Made in China
SN:
XDS212
Dual 12” Subwoofer
Frequency Response (-3dB) 50Hz–180Hz
Sensitivity (dB 1W 1M) 99 dB
Impedance 8 Ohm
Recommended Max Power (Program) 600W
FRONT PANEL
XDS10 shown here
XDS212 shown here
1 2
Full range enclosures
1
High Frequency Driver
A single horn loaded compression driver.
XDS8 1 x 1.35”. Flare: 100º x 100º non-rotatable
XDS10 1 x 1.35”. Flare: 50-100º x 50º rotatable
XDS12 1.7”. Flare: 80º x 50º rotatable
2
Low Frequency Driver
Driver sizes:
XDS8 1 x 8”
XDS10 1 x 10”
XDS12 1 x 12”
1
Subwoofers
Two passive subwoofers are available in the XDS range, a ported/front loaded
single 15” subwoofer and a dual 12” bandpass subwoofer.
1
Low Frequency Driver
Driver sizes:
XDS115 1 x 15”
XDS212 2 x 12”
PAGE 4
XDS SERIES INSTALLATION AND OPERATION MANUAL
Page 5
XDS10 shown here
XDS10
2 Way Full Range Speaker
Made in China
SN:
XDS212 shown here
REAR PANEL
XDS212
Dual 12” Subwoofer
Frequency Response (-3dB) 50Hz–180Hz
Sensitivity (dB 1W 1M) 99 dB
Impedance 8 Ohm
Recommended Max Power (Program) 600W
Made in China
SN:
1
2
1
Speaker Input
Speaker inputs are via a pair of 4pole twist lock connectors (Neutrik speakON or
compatible) wired in parallel.
The twist lock connectors are wired using pins 1+ and 1- only, with both
connectors wired in parallel. Either connector may be used as the input with the
other used as a loop through connector.
2
Handle
A single recessed carry handle.
1
1
Speaker Input
Speaker inputs are via a pair of 4pole twist lock connectors (Neutrik speakON or
compatible) wired in parallel.
The twist lock connectors are wired using pins 1+ and 1- only, with both
connectors wired in parallel. Either connector may be used as the input with the
other used as a loop through connector.
XDS SERIES INSTALLATION AND OPERATION MANUAL
PAGE 5
Page 6
MOUNTING
Wall Mount Brackets
A number of wall mount options are available for the XDS speaker range.
The wall mount U brackets permit speaker mounting in either horizontal
or vertical orientation. The brackets are supplied with enclosure mounting
plates to replace the standard pole mount and blank plate fitted to the
speakers as standard.
The XDSWMB wall mount bracket permits vertical installation with a wide
range of angular adjustment in the horizontal and vertical axis.
U brackets
330 mm (13.0”)
140 mm (5.5”)
XDS8
400 mm (15.8”)
190 mm (7.5”)
Subwoofers
The XDS series Subwoofers are designed to be free standing for floor
mounted installation.
Both models are supplied with a top mounted 35 mm pole mount boot to
suit satellite mounting via the ATC310 pole mount.
ATC310 pole mount
XDS10
515 mm (20.3”)
205 mm (8.1”)
AMIS LSB1 wall bracket
XDS12
XDSWMB wall mount bracket
60 mm (2.4”)
76 mm (3.0”)
60 mm (2.4”)
PAGE 6
XDS SERIES INSTALLATION AND OPERATION MANUAL
Page 7
MOUNTING
When mounting via a bracket or eyebolts the following must be considered.
The mounting of a permanently installed speaker may be dangerous unless
undertaken by a qualified professional with the required experience.
Walls and mounting surfaces must be capable of supporting the speaker and
bracketry in a safe and secure manner.
All fixings must be safely attached to the speaker cabinet and the mounting
surface. All fixings must be fitted in accordance with the manufacturers
instructions and specifications.
Suspending with Eyebolts
The XDS range of speakers provide a number of secured mounting points for
use with M10 eye bolts.
When suspending an XDS8, XDS10 or XDS12 loudspeaker, the two mounting
points towards the front of the cabinet should be used, with the 3rd point
used to angle the enclosure as needed.
All XDS eyebolt fittings are M10.
M10 Eyebolts with a mimimum of 20 mm usable thread must be used.
XDS212 shown here
XDS SERIES INSTALLATION AND OPERATION MANUAL
PAGE 7
Page 8
ACCESSORIES
XDS8
PART DESCRIPTION
XDS8UB U bracket for XDS8
XDSWMB Wall mounting bracket for XDS8/10/12
AMISLSB1 Wall mount bracket
ATC303 Tripod speaker stand
ATC304 Heavy duty tripod speaker stand
ATC305 Winch up speaker stand
XDS10
PART DESCRIPTION
XDS10UB U bracket for XDS10
XDSWMB Wall mounting bracket for XDS8/10/12
AMISLSB1 Wall mount bracket
ATC303 Tripod speaker stand
ATC304 Heavy duty tripod speaker stand
ATC305 Winch up speaker stand
XDS12
PART DESCRIPTION
XDS12UB U bracket for XDS12
XDSWMB Wall mounting bracket for XDS8/10/12
AMISLSB1 Wall mount bracket
ATC303 Tripod speaker stand
ATC304 Heavy duty tripod speaker stand
ATC305 Winch up speaker stand
XDS115/XDS212
PART DESCRIPTION
RNRWHL Wheel kit for XDS115/212
PAGE 8
XDS SERIES INSTALLATION AND OPERATION MANUAL
Page 9
DIMENSIONS
408.00 mm (16.1”)
293.00 mm (11.5”)
348.60 mm (13.7”)
XDS8
284.00 mm (11.2”)
XDS8
2 Way Full Range Speaker
Made in China
SN:
XDS10
502.00 mm (19.8”)
620.00 mm (24.4”)
396.00 mm (15.6”)
328.00 mm (12.9”)
XDS10
2 Way Full Range Speaker
Made in China
SN:
XDS12
480.00 mm (18.9”)
XDS SERIES INSTALLATION AND OPERATION MANUAL
XDS12
2 Way Full Range Speaker
Made in China
SN:
PAGE 9
Page 10
DIMENSIONS
XDS115
650.00 mm (25.6”)
512.00 mm (20.1”)
512.00 mm (20.1”)
XDS115
Single 15” Subwoofer
Frequency Response (-3dB) 35Hz–500Hz
Sensitivity (dB 1W 1M) 96 dB
Impedance 8 Ohm
Recommended Max Power (Program) 300W
Made in China
SN:
600.00 mm (23.6”)
XDS212
600.00 mm (23.6”)
680.00 mm (26.8”)
PAGE 10
XDS212
Dual 12” Subwoofer
Frequency Response (-3dB) 50Hz–180Hz
Sensitivity (dB 1W 1M) 99 dB
Impedance 8 Ohm
Recommended Max Power (Program) 600W
Made in China
SN:
XDS SERIES INSTALLATION AND OPERATION MANUAL
Page 11
SPECIFICATIONS
XDS8 XDS10 XDS12
Impedance (Nominal) 8 Ohms 8 Ohms 8 Ohms
Power (Continuous) 100 Watts 250 Watts 300 Watts
Sensitivty (1 W / 1 M) 92 dB 94 dB 96 dB
Calculated Max SPL 112 dB 118 dB 121 dB
Dispersion (-6 dB Points) (H x V) 100º x 100º 50-100º x 50º 80º x 50º
non-rotatable rotatable rotatable
Frequency Response (-3dB) 80 Hz - 20 kHz 55 Hz - 20 kHz 50 Hz - 18 kHz
Frequency Response (-10dB) 70 Hz - 20 kHz 50 Hz - 20 kHz 45 Hz - 20 kHz
Connection 4 pole twist lock connectors (x2) 4 pole twist lock connectors (x2) 4 pole twist lock connectors (x2)
screw terminal strip (x2) screw terminal strip (x2) screw terminal strip (x2)
Components 1 x 8” Woofer, 1 x 10” Woofer, 1 x 12” Woofer,
1 x 1.35” HF Driver 1 x 1.35” HF Driver 1 x 1.7” HF Driver
Net Dimensions (w x d x h) 293 mm x 284 mm x 408 mm 348.6 mm x 328 mm x 502 mm 396 mm x 396.4 mm x 620 mm
(11.5” x 11.2” x 16.1”) (13.7” x 12.9” x 19.8”) (15.6” x 15.6” x 24.4”)
Shipping Dimensions (w x d x h) 350mm x 350 mm x 470 mm 430 mm x 410 mm x 605 mm 480 mm x 480 mm x 720 mm
(13.8” x 13.8” x 18.5”) (16.9” x 16.1” x 23.8”) (18.9” x 18.9” x 28.3”)
Net Weight 10 kg 16.5 kg 20 kg
22.0 (lbs) 36.3 (lbs) 44.0 (lbs)
Shipping Weight 11.5 kg 18.5 kg 23 kg
25.3 (lbs) 40.7 (lbs) 50.6 (lbs)
XDS115 XDS212
Impedance (Nominal) 8 Ohms 8 Ohms
Power (Continuous) 300 Watts 600 Watts
Sensitivity (1W / 1M) 96 dB 99 dB
Calculated Max SPL 121 dB 127 dB
Frequency Response (-3dB) 35 Hz - 500 Hz 50 Hz - 180 Hz
Frequency Response (-10dB) 30 Hz - 500 Hz 45 Hz - 180 Hz
Connection 4 pole twist lock connectors (x2) 4 pole twist lock connectors (x2)
Components 1 x 15” Woofer 2 x 12” Woofers
Net Dimensions (w x d x h) 512 mm x 600 mm x 650 mm 512 mm x 600 mm x 680 mm
(20.1” x 23.6” x 25.6”) (20.1” x 23.6” x 26.8”)
Shipping Dimensions (w x d x h) 700 mm x 615 mm x 750 mm 700 mm x 615 mm x 780 mm
(27.6” x 24.2” x 29.5”) (27.6” x 24.2” x 30.7”)
Net Weight 30 kg 40 kg
66.0 (lbs) 88.0 (lbs)
Shipping Weight 35 kg 45 kg
77.0 (lbs) 99.0 (lbs)
XDS SERIES INSTALLATION AND OPERATION MANUAL
PAGE 11
Page 12
ENGINEERED BY AUSTRALIAN MONITOR
Address: 1 Clyde Street, Silverwater, Sydney NSW 2128 Australia. Private Bag 149, Silverwater NSW 1811 ACN 007 573 417
Website: www.australianmonitor.com.au International enquiries email: international@australianmonitor.com.au
DISTRIBUTED IN AUSTRALIA AND NEW ZEALAND BY HILLS SVL www.hillssvl.com.au
NSW QLD ACT WA VIC SA NZ
P: 02 9647 1411 P: 07 3852 1312 P: 02 6260 4544 P: 08 9204 0200 P: 03 9890 7477 P: 08 8408 8300 P: 09 415 9426
E: nsw@hillssvl.com.au E: qld@hillssvl.com.au E: act@hillssvl.com.au E: wa@hillssvl.com.au E: vic@hillssvl.com.au E: sa@hillssvl.com.au E: sales@hillssvl.co.nz
Loading...