Australian Monitor. SYNERGY2 Brochure

2

SYNERGY

Two Channel Power Amplifiers

Drawing on the heritage of Australian Monitor’s low impedance amplifier design comes the latest in low impedance

amplifiers from the Australian Monitor Pro series, the Synergy2. The Synergy2 series offers an impressive range of

highly powerful 2 ohm rated amplifiers in rugged yet stylish 2 RU chassis. Available in three powerful models the SY2200

will deliver 600W, the SY2400 will deliver 1100W and the SY2700 will deliver 2000W. All models also offer on board clip

limiting, ground lift switching, XLR ins and binding post and 4 pole speaker connector outputs. As with all Australian

Monitor Pro Series amplifiers they deliver the sonic clarity you’ve come to expect from an AM amp.

At a Glance

> 3 models

> All 2 ohm capable

> SY2200 2 x 110W into 8 ohm, 2 x 200W into 4 ohm, 2 x 300W into 2 ohm

> SY2400 2 x 190W into 8 ohm, 2 x 350W into 4 ohm, 2 x 525W into 2 ohm

> SY2700 2 x 400W into 8 ohm, 2 x 700W into 4 ohm, 2 x 1000W into 2 ohm

> On board clip limiter

> Ground lift switch

> XLR in and link (male/female)

> Binding post/4 pole speaker connector outs

SERIES

SYNERGY2SERIES

Architectural Specifications

The amplifier shall be of 2 channel low impedance design, of sturdy construction and shall be 2 rack units high. The amplifier

shall have on board clip limiting, ground lift switching, XLR inputs and 4 pole speaker connector and binding post outputs.

Front panel level controls will be provided as well as status, overload, thermal, power and fault indication. The amplifier will

be capable of 2 ohm operation and shall have overload, output short circuit, thermal and output DC protection as well as a

slow start facility. The amplifier shall be an Australian Monitor Synergy2 series.

Common Specifications (To all SY2 Amplifiers)

Distortion (re: 4ohm, 1dB below clip)
THD (@ 1kHz)
<0.02% IMD SMPTE (60Hz : 7kHz 4:1)
<0.03%

Input Impedance 20kohms

Input Sensitivity 1Vrms

Input CMRR >80dB

Signal/Noise Ratio A-Weighted
>104dB

Crosstalk >70dB

Slew rate >40 V/µsec

Damping factor (@ 1kHz re 8 ohms)
> 375:1

Frequency response (+/-3dB)
15 Hz- 50 kHz

Indicators Power, Status (L/R), Overload, Thermal, Fault

Model

Output Power

Voltage Gain

Thermal Dissipation

Current Draw

Dimensions (H x W x D)

Unit Weight

Shipping Weight

Shipping Dimensions (H x W x D)

ENGINEERED AND DISTRIBUTED BY AUSTRALIAN MONITOR ABN 78 001 345 482

149 Beaconsfield Street, Silverwater Sydney NSW 2128 Australia

SY 2200 SY 2400 SY 2700

300W 0.1% THD @ 1kHz

28.3 (29dB)

Both channels driven, 2ohm load

1/8th power

425W (1450btu/hr)

Both channels driven, 2ohm load, 230Vac

1/8th power

2.7A

87mm x 482mm x 400mm

12.5kg

14 Kg

210mm x 540mm x 540mm

525W 0.1% THD @ 1kHz

37.4 (31dB)

Both channels driven, 2ohm load

1/8th power

780W (2661btu/hr)

Both channels driven, 2ohm load, 230Vac

1/8th power

5.0A

87mm x 482mm x 400mm

15.5kg

17 Kg

210mm x 540mm x 540mm

NSW Tel: [phone] Fax: [phone]

VIC Tel: [phone] Fax: [phone]

QLD Tel: [phone] Fax: [phone]

SA Tel: [phone] Fax: [phone]

WA Tel: [phone] Fax: [phone]

NZ Tel: [phone] Fax: [phone]

1000W 0.1% THD @ 1kHz

52.9 (34dB)

Both channels driven, 2ohm load

1/8th power

1410W (4811btu/hr)

Both channels driven, 2ohm load, 230Vac

1/8th power

9.1A

87mm x 482mm x 455mm

17.5kg

19 Kg

210mm x 540mm x 575mm