Australian Monitor. SM12, SM16 User Manual
Australian Monitor Pro
The
mixers
console
feature
With
a
and switchable 48V
3 stage
mixers
are designed to be
packed.
mixture of mono channels featuring balanced XLR or TRS inputs
pre
E0 and
as versatile as they are cost effective.
are
Series SM12 and SM16 stereo
compact,
phantom power,
postlader
and
and
auxiliary sends, the SM series
low noise
ultra
stereo channels all
INTRODUCTION
and
MONO CHANNELS
STEREO CHANNELS
boasting
MASTER SECTION
The
SM Series
filters on all mono channels, high
potentiometers.
graph
meters for the
The Australian Monitor Pro
professional
versatility
and
mixers feature
19 inch rack mount kit and
stereo output
a sonically superior mixing console offering a feature set
usually
peak
Series
found in mixing consoles many times their
LED indication and low cut
quality
60mm faders and sealed
accurate
buss.
SM12 and SMl6
10 segment bar
give
the audio
price.
REAR PANEL
OPERATION
BLOCK DIAGRAM
SPECIFICATIONS
gUR,
AUS,
Copyrigtrt
tTth
Rev A: lfth Oct 2Of
Oct
t0
USA
2U!4
CAUTION
CAUTION:
TO REDUCE THE RISK OF ELECTRIC
DO NOT REMOVE COVER
NO
USER-SERVICEABLE
(OR
PABTS INSIDE.
BACK).
WARNING !
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK.
DO NOT EXPOSE
SMt2 &
gM16
THIS
EOUIPMENT
TO RAIN OR MOISTURE.
0ptRAT|*H f!4ANUAL
SHOCK.
A
A
Caution:
This symbol is intended to alert
of uninsulated
enclosure
constitute a
This symbol is intended to alert
of important operation and
instructions in the literature accompanying
prevent
To
with
an extension
the blades can be
prevent
To
wide slot, fully insert.
"dangerous voltage"
that may
electric shock do
electric shock,
be of
risk
of electric
cord, receptacle
fully inserted
the user to
within the
sufficient magnitude to
shock to
maintenance
match wide blade
persons.
the
user
not use this
or
other
prevent
to
pres€nce
the
product's
presence
to the
(servicing)
the
appliance.
(polarised) plug
outlet unless
blade exposure.
plug
of
lo
PAGE 3
MIC/LINE
r',lrc
{$
Balanced
INPUT
SECTION @
XLR input
uro
This mid range E0
range frequencies
octave
bandwidth at 2.5kHz. This control
give
will
centre
up to l5dB of boost or cut. The
position
control adiusts mid
and has a fixed 2
give
will
a flat response.
i:if.,rl""r,*,.
"@
For
LIN
E
6.35mm TRS input
Unbalan@d use of
mono 1/{"iack
TiP
=
Signal
Grcund/Shield
r-ow
@
This switch will roll
75Hz
at an 18dB
can be used to eliminate rumble
i.
i
\
!
t
by sensitive lectern
onrru
@
This is
input
and should be set to optimise
inputs level while
so the input signal does not reach clipping
level. This
+10d8 to +60d8.
EG SECTION
uroH
@
This is
frequency
of boost or cut at l2kHz. The centre
position
pi.
unhland u*
plugs
1 ad
cur FTLTER swrrcH
per
the initial
a shelf E0 filter that adjusts treble
gain
still leaving headroom
gain
stage has a range from
levels and will
give
will
a flat response.
@^,_
pin
3 hv€ L b bndg€d
Balanced use ot
sterco l//1"
Ring
Gound /Shisld
Tip
Ring
For onndton of balaned
unbalaned
have b h bridgsd at ihe sters
off
octave slope. This
mics etc.
control for
plugs
lack
-
=
plugs,
dng and sleve
frequencies
give
up to 15dB
caused
each
ad
plug
below
each
r-ow
$
This low frequency
adjusts
bass
up to 1 5dB of boost or cut
position
centre
AUXILIARY
enr
@
Aux
signal and is
channel
rosr
@
Aux 2 is a mono
signal and is
channel fader.
e*r.r
@
The
tion
err
@
The Pre Fader Listen
SECTION
1 is a mono split of the channel
fader.
channel
the channel signal in the stereo
shelf E0 control
frequencies
give
will
post
E0 but
split of the channel input
post
E0
and
pan
control is used to
(PFL)
to monitor the input signal
channel fader. This can be switched
either the headphone/local monitor
or the master lelVright outputs
(see
master section)
eenrc
@
@
r-ro
This
red LED illuminates when the
channel is
going
into overload
r-evrr-
This
channel output fader adjusts the
level
of the channels signal before it
is sent to the master output buss.
and will
at 80H2. The
flat response.
a
pre
the
post
switch
before the
(clip)
give
posi-
is
output
inpul
field.
used
to
PAGE 4
SM12
& SM16 OPERATION MANUAL
Loading...