Page 1
INSTALLATION AND OPERATION MANUAL
sales@wes.net.au
www.wes.net.au
QF6WRC
WATER
RESISTANT CEILING SPEAKER
Page 2
IMPORTANT SAFETY INFORMATION PRÉCAUTIONS DURANT UTILISATION
sales@wes.net.au
www.wes.net.au
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
9. Only use attachments/accessories specified by the manufacturer.
10. Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled or objects have fallen into
the apparatus, the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.
11. This appliance shall not be exposed to dripping or splashing water and that
no object filled with liquid such as vases shall be placed on the apparatus.
1. Lisez ces instructions.
2. Tenez ces instructions.
3. Notez tous les avertissements.
4. Suivez toutes les avertissements.
5. N’utilisez pas ce produit près de l’eau (la piscine, la plage, le lac, etc.).
6. Nettoyez seulement avec une étoffe sèche.
7. Ne bloquez aucuns troux de ventilation. Installez en accord avec
les instructions du manufacturier.
8. N’installez près aucunes sources de chaleur comme radiateurs, registres
de chaleur, fours ou les autres équipements (y compris amplificateurs)
qui produisent la chaleur.
9. Seulement utilisez attachements/accessoires spécifiés par le
manufacturier.
10. Référez au personnel qualifié de service pour toutes réparations.
La réparation est donnée quand le système a été endommagé à n’importe
façon, par exemple un fil ou une fiche endommagé(e) de la source
d’alimentation. Avoir été exposé à pluie ou humidité, n’opère pas
normalement, ou avoir été tombé.
11. L’appareil ne doit pas être exposé aux écoulements ou aux éclaboussures
et aucun objet ne contenant de liquide, tel qu’un vase, ne doit être placé
sur l’objet.
Page 3
INTRODUCTION AND CONTENTS
sales@wes.net.au
www.wes.net.au
QF6WRC
The Australian Monitor QF6WRC ceiling mount speaker
is designed to provide a water resistant option to
complement the outstanding QF quick fit range of
Australian Monitor ceiling speakers.
Being IEC 529 IP55 rated, the QF6WRC is the perfect
option for areas that may be exposed to damp conditions
and moisture including bathrooms and wet areas.
The QF6WRC is rated at 12 Watts at 8 Ohms with 100V
power tappings at 12, 9, 6, 3 and 1 Watts or 70V tappings
at 6, 4.5, 3, 1.5 and 0.5 Watts and is perfect for speech or
background music applications.
The speaker features a sealed ABS rear enclosure with a
glanded cable tail for easy installation. Mounting is by
way of rotating mounting tabs and the speaker features
a 6” full range driver to ensure
smooth operation.
The QF6WRC from Australian Monitor offers exceptional
versatility, performance and value for money.
water resistance and
INTRODUCTION 3
FRONT PANEL 4
REAR PANEL 5
MOUNTING 6
DIMENSIONS 8
SPECIFICATIONS 9
FREQUENCY RESPONSE 10
NOTES 11
Version 1.0 September 2013
QF6WRC INSTALLATION AND OPERATION MANUAL
PAGE 3
Page 4
FRONT PANEL
sales@wes.net.au
www.wes.net.au
4
2
1
4 4
1
6” full range driver
2
Front grille plate
3
Grille
4
Grille mounting tabs
3
PAGE 4
QF6WRC INSTALLATION AND OPERATION MANUAL
Page 5
REAR PANEL
sales@wes.net.au
www.wes.net.au
3
1
2
1
Speaker Input Cable
Speaker input is via a 7 core cable. Refer to the
attached table which identifies the various power
tappings available and also the 8 Ohm direct input.
2
Power Tapping Chart
for easy reference
3
Mounting tabs
(refer to mounting section).
3
QF6WRC
IP Rated Splashproof Ceiling Loudspeaker
Power
+
Common
Line
Low-imp.
Impedance
Black 70 V 100 V
Brown 6 W 12 W 833 Ω
Red 4.5 W 9 W 1.11 kΩ
Blue 3 W 6 W 1.67 kΩ
Yellow 1.5 W 3 W 3.33 kΩ
Green 0.5 W 1 W 10 kΩ
White 12 W 12 W 8 Ω
3
Tapping 100 V 70 V Impedance
Brown 12 W 6 W 833 Ω
Red 9 W 4.5 W 1.11 kΩ
Blue 6 W 3 W 1.67 kΩ
Yellow 3 W 1.5 W 3.33 kΩ
Green 1 W 0.5 W 10 kΩ
White Direct 8 Ω
Black Common
Brown
Red
Blue
Yellow
Green
White
Black
QF6WRC INSTALLATION AND OPERATION MANUAL
PAGE 5
Page 6
MOUNTING
sales@wes.net.au
www.wes.net.au
When mounting QF6WRC speakers the following safety issues must be considered;
The mounting of a permanently installed speaker may be dangerous unless
undertaken by a qualified professional with relevant experience.
Ceilings and mounting surfaces must be capable of
supporting the speaker in a safe and secure manner.
Installation
(Refer to page 8 for dimension details)
Cut a hole with a diameter of 209 mm (8.3”) in the ceiling ensuring that there is sufficient
room both above and at the sides of the hole to comfortably fit the speaker.
To install the speaker, remove the grille by placing a screwdriver into the three grille release
tabs (slots) located around the circumference of the front panel and carefully prying it free.
Take care not to scratch the panel with the screwdriver.
Once the grille and front panel have been removed, simply insert the speaker into the ceiling
and using a screwdriver, tighten the three mounting tabs located around the circumference
of the speaker to lock it into place. Once the speaker is installed, relocate the grille and front
plate by securely pressing it back into place.
When wiring the speakers, always connect multiple speaker in parallel and ensure the
correct polarity of each speaker, with respect to each other is maintained. Isolate unused
wires in the speaker input cable so that they do not contact each other or any other
conductive object..
NOTE that the QF6WRC has a supervisory capacitor inserted across all 100V tappings.
PAGE 6
QF6WRC INSTALLATION AND OPERATION MANUAL
Page 7
MOUNTING
sales@wes.net.au
www.wes.net.au
Removing the Grille
To remove the grille, simply unclip the front grille plate from the speaker by pressing the
grille release tabs which are identified from the front by three small indents located around
the circumference of the plate.
If the grille is to be removed whilst the speaker is not mounted, we recommend releasing
the tabs from the rear of the speaker so that the front panel is not scratched. If removing
from the front, take care not to scratch the front panel.
Once the panel is removed, the grille itself can be removed from the front panel by turning
it anticlockwise until the small tabs that hold it in place are released.
To reassemble, reinsert the grille following the reverse process and the front plate is
simply pressed back into the speaker.
QF6WRC INSTALLATION AND OPERATION MANUAL
PAGE 7
Page 8
DIMENSIONS
sales@wes.net.au
www.wes.net.au
ø 238.4 mm (9.4”)
137.5 mm (5.4”)
PAGE 8
183.3 mm (7.2”)
10.3 mm (0.4”)
QF6WRC INSTALLATION AND OPERATION MANUAL
Page 9
SPECIFICATIONS
sales@wes.net.au
www.wes.net.au
SPECIFICATION QF6WRC
Impedance (Direct) 8 Ohms
Power (Continuous, Program) 12 W, 24 W
Power Tappings (100 V) 12, 9, 6, 3, 1 Watts
(70 V) 6, 4.5, 3, 1.5, 0.5 Watts
Sensitivity (1 W / 1 M @ 1 kHz) 92 dB
Calculated max SPL 103 dB, 109 dB
(Continuous, Program)
Dispersion (1 kHz, 4 kHz)
Frequency Response (-10dB) 150 Hz – 20 kHz
Frequency response (-3 dB) 185 Hz - 19 kHz
Speaker Components 6” Full Range Driver
Ingress Protection IEC 529 IP 55
Operating Temperature -30°C ~ +60°C
Net Dimensions (diameter x length) 238.4 x 137.5 mm (9.4” x 5.4”)
Net Weight (no carton) 1.7 kg (3.75 lbs)
Shipping Dimensions (W x H x D) (carton) 270 x 270 x 215 mm
110°, 65° conical
10.6” x 10.6” x 8.5”)
Shipping Weight (carton) 2.4 kgs (5.3 lbs)
QF6WRC INSTALLATION AND OPERATION MANUAL
PAGE 9
Page 10
FREQUENCY RESPONSE
sales@wes.net.au
www.wes.net.au
PAGE 10
QF6WRC INSTALLATION AND OPERATION MANUAL
Page 11
NOTES
sales@wes.net.au
www.wes.net.au
QF6WRC INSTALLATION AND OPERATION MANUAL
PAGE 11
Page 12
sales@wes.net.au
www.wes.net.au
Loading...