AUSTRALIAN MONITOR AMD2100P Installation And Operation Manual

INSTALLATION AND OPERATION MANUAL
POWER AMPLIFIER AMD2100P
AMD SERIES
Read these instructions.1.
Keep these instructions.2.
Heed all warnings.3.
Follow all instructions.4.
Do not use this apparatus near water.5.
Clean only with dry cloth.6.
Do not block any ventilation openings. Install in accordance with the 7. manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers, 8. stoves, or other apparatus (including amplifiers) that produce heat.
Protect the power cord from being walked on or pinched particularly 10. at plugs, convenience receptacles, and the point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.11.
Use only with the cart, stand, tripod, bracket, or table specified by the 12. manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
Unplug this apparatus during lightning storms or when 13. unused for long periods of time.
Refer all servicing to qualified service personnel. 14. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
This appliance shall not be exposed to dripping or splashing water and 15. that no object fi lled with liquid such as vases shall be placed on the apparatus.
Connect the equipment to an appropriate wall outlet that is readily 16. accessible.
The mains plug is used as the disconnect device and shall remain 17. readily accessible. If the mains plug is not readily accessible due to mounting in a 19” rack, then the mains plug for the entire rack must be readily accessible.
WARNING:18. To reduce the risk of fi re or electric shock, do not expose this apparatus to rain or moisture.
An appliance with a protective earth terminal should be connected to a 19. mains outlet with a protective earth connection.
LISEZ ces instructions.1.
Tenez ces instructions.2.
Notez tous les avertissements.3.
Suivez toutes les avertissements.4.
N’utilisez pas ce produit près de l’eau (la piscine, la plage, le lac, etc.).5.
Nettoyez seulement avec une étoffe sèche.6.
Ne bloquez aucuns troux de ventilation. Installez en accord avec 7. les instructions du manufacturier.
N’installez près aucunes sources de chaleur comme radiateurs, registres 8. de chaleur, fours ou les autres équipements (y compris amplifi cateurs) qui produisent la chaleur.
Ne défaites pas le but de sécurité de la fi che polarisée ou base-type. 9. Une fi che polarisée a deux tranchants avec un plus large que l’autre. Une fi che de base type a deux a deux tranchants et une troisième pointe de base, le tranchant large ou la troisième pointe est fourni pour votre sécurité. Si la fi che donnée ne conforme pas votre prise de contact, consultez un électricien pour remplacement de la prise de contact obsolète.
Protegez le cordon de secteur contre être marchée dessus ou pincez 10. en particulier aux fi ches, aux douilles de convenance, et au point où ils sortent de l’appareil.
Seulement utilisez attachements/accessoires spécifi és par le 11. manufacturier.
Utilisez seulement avec un chariot, un stand, un trépied, un support 12. ou une table indiquée par le manufacturier, ou vendue avec l’appareil. Quand un chariot est utilisé, faites attention en déplaçant la combinaison d’appareil/chariot pour éviter de se déséquilibrer.
Arrachez la fi che du dispositif durant éclair et orage ou 13. quand pas utilisé pour longues périodes de temps.
Référez au personnel qualifi é de service pour toutes 14. réparations. La réparation est donnée quand le système a été endommagé à n’importe façon, par exemple un fi l ou une fi che endommagé(e) de la source d’alimentation. Avoir été exposé à pluie ou humidité, n’opère pas normalement, ou avoir été tombé.
L’appareil ne doit pas être exposé aux écoulements ou aux éclaboussures 15. et aucun objet ne contenant de liquide, tel qu’un vase, ne doit être placé sur l’objet.
Branchez l’appareil à une source appropriée et faire que la prise à 16. débrancher soit facilement accessible.
La prise du secteur ne doit pas être obstruée ou doit être facilement 17. accessible pendant son utilisation. Pour être complètement déconnecté de l’alimentation d’entrée, la prise doit être débranchée du secteur.
AVERTISSEMENT: 18. Pour éviter le risque d’incendie ou de chocs électriques, ne pas exposer cet appareil à la pluie ou à l’humidité.
Un appareil avec la borne de terre de protection doit être connecté au 19. secteur avec la connexiion de terre de protection.
IMPORTANT SAFETY INFORMATION PRÉCAUTIONS DURANT UTILISATION
PAGE 2
AMD2100P INSTALLATION AND OPERATION MANUAL
The AMD P series of power amplifi ers from Australian Monitor represent a quantum leap forward in connectivity, controllability & fl exibility in the constant voltage amplifi er market. The AMD series allows a contractor to integrate the power amplifi er to a third party control system for remote audio control or simply use the AMD amplifi ers as standard power amplifi ers.
Australian Monitor AMD P series is the future of constant voltage amplifi cation.
Revision 1.0 January 2011
INTRODUCTION 3
FRONT PANEL 4
REAR PANEL 5
INSTALLATION 6
RS232 PROTOCOL 7–8
COMMAND SUMMARY 9
DIMENSIONS 10
SPECIFICATIONS 11
WARNING!
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT USE THE PLUG WITH
AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES
CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
TO PREVENT ELECTRICAL SHOCK, MATCH WIDE BLADE PLUG TO WIDE SLOT, FULLY INSERT.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning fl ash with arrowhead symbol,
within an equilateral triangle, is intended
to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of
suffi cient magnitude to constitute a risk
of electric shock to persons.
WARNING: TO REDUCE THE RISK
OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The exclamation point within an equilateral
triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
Rating plate and caution marking are marked on the back enclosure of the apparatus
AMD2100P
PAGE 3
AMD2100P INSTALLATION AND OPERATION MANUAL
INTRODUCTION AND CONTENTS
1
Signal Indicator
The signal indicator will go blue when audio is present on that channel of the amplifi er.
2
Fault Indicator
The fault indicator will go red when a fault is present on that channel of the amplifer.
3
Clip Indicator
The clip indicator will go red when an audio input is reaching the clipping stage. If this is happening the input should reduced using the input attenuator at the rear of the unit, or at the program source.
4
Control Indicator
The control indicator will fl ash whenever a control system adjusts a parameter inside the amplifi er.
2 3 4
1
PAGE 4
AMD2100P INSTALLATION AND OPERATION MANUAL
FRONT PANEL
Loading...
+ 8 hidden pages