Australian monitor ACM604P User Manual

ACM604P

4 x 60w Power Amplifier

Operating Manual

ACM604P, 4 x 60 Watt Power Amplifier

Product Description

The ACM604P is a four channel (4 x 60w) power amplifier designed for commercial installations. The one unit contains
four independent 60 watt amplifiers for multi-zone applications. The ACM604P can be used for either low impedance (8
ohm) or 70v/100v line speaker systems per channel. The amplifier can be mounted in a standard 19” equipment rack (rack
ears supplied) or it can be used on a shelf or table. The ACM604P features a line level input (with parallel output) per
channel and is normally used with mixers, mixer amplifiers or other power amplifiers.

Front Panel Features

Power Switch

The black rocker switch on the right hand side of the front panel is used to switch the amplifier on and off. The ‘up’
position is on. When the amplifier is connected to an appropriate AC power source and is switched on, the blue power
LED will illuminate.

On LED

The blue “On” LED above the power switch will illuminate when the amplifier is connected to mains power and is
switched on.

Signal LED

The green “Signal” LED’s located next to the On LED indicate that the ACM604P is receiving audio signal via its line
level inputs. One LED is provided per channel. The signal LED’s are a simple way of trouble-shooting installations
especially in multi amplifier projects. At a glance the signal LED’s will indicate that audio is reaching the amplifier .

Rack Mounting

The ACM604P is supplied with rack ears attached to allow mounting within a standard 19” equipment rack. As is the
case with almost all audio products, adequate ventilation and air flow is required. When installing multiple ACM
amplifiers within the one rack, it is recommended that at least 1 rack unit of ventilation space is left between every two
amplifiers.

For table or shelf mounting, the rack ears can be removed using a screwdriver. Once the rack ears are removed, please
reinstall the screws.

Rear Panel Features

AC Power Inlet

The 3 pin IEC power inlet is located on the bottom left of the rear panel and accepts a standard mains power lead fitted
with an IEC connector. Before plugging in a power lead, please check the rear panel of the amplifier to ensure that the
voltage label shows the correct AC operating voltage for your part of the world.

The inlet is equipped with an in-built AC fuse holder fitted with a 5 Amp slow blow fuse plus a spare fuse. Please ensure
that the mains power cord is disconnected before attempting to check or replace this fuse. Power consumption is 400
watts (max).

Speaker Output Terminal Strip

Located on the top half of the rear panel are the speaker output terminal strips. A terminal strip is provided for each of
the four amplifiers. Reading from left to right, the connections per terminal strip are:

COM Common or “-” for low impedance speaker loads (8 ohms).
8 The “+” for 8 ohm speaker loads (use with common)

COM Common or “-” for 70v or 100v speaker loads (maximum load of 160 ohms at 100v)
70 The “+” for 70v line speaker loads (use with common)
100 The “+” for 100v line speaker loads (use with common)

Please ensure that the correct “Common” is used. Low impedance and 70/100v loads can be used simultaneously but
please pay careful attention to the overall speaker load. When used individually, the low impedance load should be 8
ohms or higher while the 100v line load should not fall below 160 ohms per amplifier. When both low impedance and 70/
100v outputs are used simultaneously on the one amplifier, ensure that neither output is loaded to maximum.

Level Control

Located next to the XLR input/output is a recessed screwdriver adjustable level control. One is provided per amplifier
channel. The level control is an input attenuation control normally used to match the amplifier to a wide variety of input
signals. In essence, the amplifier is designed to receive a 700mv input signal however the level control can be used to
increase the level for lower signals or decrease the level for higher input signals. In normal use, the level control is used
as a ‘set and forget’ master level control for the amplifier.

XLR Audio Input and Parallel Output

The ACM604P includes both male and female 3 pin XLR connectors per channel. While the female is normally used as
the input to the amplifier, both XLR’ s are connected in parallel so either will work. When signal is connected to one XLR,
the other XLR becomes a line level output allowing the input signal to be distributed (split) to other amplifiers. In some
projects, the same input may be looped through to multiple amplifiers using this method. Up to 6 amplifiers can be looped
together without any noticeable loss in level. A distribution amplifier should be used when more than 6 amplifiers need
to be looped.

The XLR’s are wired as follows: Pin 1: Shield. Pin 2: Hot, +, Positive. Pin 3: Cold, -, Negative

Important Safety Information

1. Save the carton and packing material even if the equip­ment has arrived in good condition. Should you ever

need to ship the unit, use only the original factory pack­ing.

2. Read all documentation before operating your equip-
ment. Retain all documentation for future reference.

3. Follow all instructions printed on unit chassis for
proper operation.

4. Do not spill water or other liquids into or on the unit,
or operate the unit while standing in liquid.

5. Make sure power outlets conform to the power re-
quirements listed on the back of the unit.

6. Do not use the unit if the electrical power cord is
frayed or broken. The power supply cords should be
routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying
particular attention to cords and plugs, convenience re­ceptacles, and the point where they exit from the
appliance.

7. Always operate the unit with the AC ground wire
connected to the electrical system ground. Precautions
should be taken so that the means of grounding of a
piece of equipment is not defeated.

8. Mains voltage must be correct and the same as that
printed on the rear of the unit. Damage caused by
connection to improper AC voltage is not covered by
any warranty .

9. Have gain controls on amplifiers turned down during
power-up to prevent speaker damage if there are high
signal levels at the inputs.

10. Power down & disconnect units from mains voltage

before making connections.

11. Never hold a power switch in the “ON” position if it
won’t stay there itself!

12. Do not use the unit near stoves, heat registers, ra­diators, or other heat producing devices.

13. Do not block fan intake or exhaust ports. Do not
operate equipment on a surface or in an environment
which may impede the normal flow of air around the
unit, such as a bed, rug, weathersheet, carpet, or com­pletely enclosed rack. If the unit is used in an extremely
dusty or smoky environment, the unit should be peri­odically “blown free” of foreign matter.

14. Do not remove the cover. Removing the cover will
expose you to potentially dangerous voltages. There
are no user serviceable parts inside.

15. Do not drive the inputs with a signal level greater

than that required to drive equipment to full output.

16. Do not connect the inputs / outputs of amplifiers
or consoles to any other voltage source, such as a

battery, mains source, or power supply, regardless of
whether the amplifier or console is turned on or off.

17. Do not run the output of any amplifier channel

back into another channel’s input. Do not parallel- or
series-connect an amplifier output with any other
amplifier output.

Audio Telex Communications Pty Ltd is not respon­sible for damage to loudspeakers for any reason.

18. Do not ground any red (“hot”) terminal. Never
connect a “hot” (red) output to ground or to another
“hot” (red) output!

19. Non-use periods. The power cord of equipment
should be unplugged from the outlet when left un­used for a long period of time.

20. Service Information Equipment should be serviced
by qualified service personnel when:

A. The power supply cord or the plug has been
damaged.
B. Objects have fallen, or liquid has been spilled into
the equipment

C. The equipment has been exposed to rain
D. The equipment does not appear to operate normally ,

or exhibits a marked change in performance
E. The equipment has been dropped, or the enclosure
damaged.

Engineered by Audio T elex Communications Pty Ltd, Sydney , Australia

A.B.N. 78 001 345 482 Inc in NSW

www.audiotelex.com.au

Export Sales & Corporate Head Office

Private Bag 149, Silverwater NSW 1811

149 Beaconsfield Street, Silverwater NSW 2128

E-mail: [e-mail]

Australia
Ph: 61-2- 9647 1411
Fax: [phone]

Sydney (NSW & ACT Sales)

Private Bag 149, Silverwater NSW 1811
149 Beaconsfield Street, Silverwater NSW 2128
Ph: [phone]
Fax: [phone]
E-mail: [e-mail]

Melbourne (Vic & Tas Sales)

P.O. Box 131, Blackburn South VIC 3130
22/277 Middleborough Road, Box Hill VIC 3128
Ph: [phone]
Fax: [phone]
E-mail: [e-mail]

Brisbane (Qld Sales)

P.O. Box 871, Fortitude Valley QLD 4006
42 Commerical Road, Fortitude Valley QLD 4006
Ph: [phone]
Fax: [phone]
E-mail: [e-mail]

Adelaide (SA & NT Sales)

P.O. Box 157, Hindmarsh SA 5001

31 Walsh Street, Thebarton SA 5031

Ph: [phone]

Fax: [phone]

E-mail: [e-mail]

Perth (W A Sales)

P.O. Box 404, North Perth WA 6906

299 Fitzgerald Street, West Perth WA 6005

Ph: [phone]

Fax: [phone]

E-mail: [e-mail]

Auckland (NZ Sales)

P.O. Box 512, Albany 1331

Unit B, 11 Piermark Drive, Albany 1331

Ph: [phone]

Fax: [phone]

E-mail: [e-mail]