Australian monitor ACM120 BROCHURE

ACM120

120W, 4 Channel Mixer Amplifier

Description

The ACM120 is a 4 channel, 120 watt mixer amplifier suitable for rack or desk mounting. The

amplifier is a self contained compact unit of solid steel construction.

Inputs

The ACM120 has four universal input channels with separate level controls. Each channel will

accept balanced or unbalanced microphone, line and auxiliary inputs. The unit has industry

standard XLR microphone sockets and dual RCA auxiliary sockets for each channel. Line input

4 has a lower input sensitivity and is suitable for high level CD players.

Outputs

The ACM120 features 100 volt, 70 volt, 4 & 8 ohm isolated transformer outputs, plus a tape

recorder output by means of dual RCA sockets. A balanced 700mV XLR output is also provid-

ed to feed up to six power amplifiers.

Speaker Zone Selector

A six position push button speaker zone selector with overriding ”all call“ is located on the

front panel. Each of the six zone selectors switch the 100 volt speaker line output to six sepa-

rate speaker zones. The ”all call“ selector overrides all 6 zones regardless of their on/off con-

dition and places the 100 volt output to all six zones.

Tone Generator

The ACM120 comes standard with an in-built four tone generator module. Tones include Bell,

Pre-Announce Chime, Alert Tone (AS2220.1) and Evacuate Tone (AS2220.1). Any of these

tones may be activated from a simple contact closure connected to the rear panel of the ampli-

fier. A Pre-announce defeat switch is located on the front panel.

Muting

VOX muting is standard on the ACM120. A mic or line signal on channels 1 or 2 will mute chan-

nels 3 and 4. The muting function can be disabled via an internal link.

Phantom Power

Phantom Power (18V DC) is available from all mic inputs. A rear panel phantom power on/off

switch is also provided.

Protection

Internal current limiting protects the amplifier from both overload and overdrive conditions.

Australian Monitor Installation Series amplifiers feature a protection network that provides

greater stability and performance. Our amplifiers are recognised

worldwide for their reliability and this is due to the extensive levels of

current limiting which protect the amplifiers from both overload and

overdrive conditions.

Power Output 120 Watts RMS

Maximum Load 80 Ohms @ 100 Volts

Power Bandwidth 60Hz - 15kHz < 0.5% THD

Frequency Response 60Hz - 15kHz (± 3dB)

Total Harmonic Distortion 0.5% @ 1kHz rated power

Signal To Noise Ratio -74dB with all controls at their centre position

Tone Controls Bass @ 100Hz: Boost +12dB Cut -12dB; Treble @ 10kHz: Boost +9dB Cut -9dB

Inputs Four mic/aux universal inputs with XLR female mic sockets and

dual RCA aux sockets

Input Sensitivity Mics: 1mV @ 200 Ohms; Aux 1-3: 75mV @ 47K Ohms; Aux 4: 300mV @ 47K Ohms

Outputs Speaker: 100, 70 Volts, 4 & 8 Ohms; Tape: 350mV @ 10K Ohms; Line: Balanced 700mV

Phantom Power 18 Volts DC on all Mic inputs (rear panel on/off switch)

Speaker Zone Selection Speaker zone selector, switches 100V line output to 6 separate zones.

An ”all call“ switch overrides all zones.

Controls 4 input channel gain controls, 1 Bass control,1 Treble control,

1 Master gain control, 6 Speaker zone selector, 1 Speaker ”all call“ selector,

Pre-announce defeat switch, Phantom Power switch (on rear panel)

Indicators Power ”on” LED

Power Source AC 230/240V - 60Hz, 110V - 50Hz (special) 3 pin IEC connector

Power Consumption 250 Watts

Protection Soft limiter for overload and overdrive protection, plus AC and DC fuses

Dimensions/Weight 88mm H x 480mm W x 330mm D (Chassis dimensions only). 12kg

Rack Mounting Standard

Tone Generators Built-in four tone generator module.

Includes Bell, Pre-Announce, Alert and Evac tones

Muting Built-in VOX muting. Channels 1 and 2 will mute channels 3 and 4

ARCHITECTURAL AND ENGINEERING SPECIFICATIONS

The mixer amplifier shall have four universal input channels, each comprising of a balanced microphone

input with XLR female sockets and an auxiliary input using dual RCA sockets. The 100 volt line speaker

outputs should be able to be switched via a six position selector with ”all call“. A balanced XLR output to

drive additional power amplifiers shall also be provided.

The amplifier master section shall include one master gain control, two EQ controls, one with 12dB of

cut and boost at 100Hz and the other with 9dB of cut and boost and 10kHz speaker outputs shall be

transformer isolated at 100 volt, 70 volt, 4 & 8 ohms. The amplifier must be capable of delivering 120

watts RMS into an 80 inductive ohm load, with less than 0.5% distortion measured at 1kHz and with

system hum and noise less than -74dB.

The amplifier shall be an Australian Monitor Installation Series model ACM120.

Engineered and Distributed By AUDIO TELEX COMMUNICATIONS PTY LTD (ABN 78 001 345 482), 149 Beaconsfield Street, Silverwater, Sydney, NSW, 2128 Australia

NSW Tel: [phone] Fax: [phone] VIC Tel: [phone] Fax: [phone] QLD Tel: [phone] Fax: [phone] WA Tel: [phone] Fax: [phone]

TAS Tel: [phone] Fax: [phone] SA Tel: [phone] Fax: [phone] Export Enquiries: [e-mail]

Website: www.australianmonitor.com.au