UM-UV-621-M30-Q215V1 www.austin-hughes.com
User Manual
dedicated LCD display solutions
Designed and manufactured by Austin Hughes
NAP-M30
Aluminum front bezel
OP-M30
Universal Mounting Open Frame
AP-M30
30” Ultra Widescreen 2560 x 1600 LCD
Front NEMA4 / IP65
UM-UV-621-M30-Q215V1 www.austin-hughes.com
Legal Information
First English printing, October 2002
Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness
of the contents. The information in this document is subject to change without notice. We are not liable for any injury or
loss that results from the use of this equipment.
Safety Instructions
Please read all of these instructions carefully before you use the device. Save this manual for
future reference.
■ Unplug equipment before cleaning. Don’t use liquid or spray detergent; use a moist cloth.
■ Keep equipment away from excessive humidity and heat. Preferably, keep it in an air-conditioned environment with
temperatures not exceeding 40º Celsius (104º Fahrenheit).
■ When installing, place the equipment on a sturdy, level surface to prevent it from accidentally falling and causing
damage to other equipment or injury to persons nearby.
■ When the equipment is in an open position, do not cover, block or in any way obstruct the gap between it and the
power supply. Proper air convection is necessary to keep it from overheating.
■ Arrange the equipment’s power cord in such a way that others won’t trip or fall over it.
■ If you are using a power cord that didn’t ship with the equipment, ensure that it is rated for the voltage and current
labeled on the equipment’s electrical ratings label. The voltage rating on the cord should be higher than the one listed
on the equipment’s ratings label.
■ Observe all precautions and warnings attached to the equipment.
■ If you don’t intend on using the equipment for a long time, disconnect it from the power outlet to prevent being
damaged by transient over-voltage.
■ Keep all liquids away from the equipment to minimize the risk of accidental spillage. Liquid spilled on to the power
supply or on other hardware may cause damage, fi re or electrical shock.
■ Only qualifi ed service personnel should open the chassis. Opening it yourself could damage the equipment and
invalidate its warranty.
■ If any part of the equipment becomes damaged or stops functioning, have it checked by qualifi ed service personnel.
What the warranty does not cover
■ Any product, on which the serial number has been defaced, modifi ed or removed.
■ Damage, deterioration or malfunction resulting from:
□ Accident, misuse, neglect, fi re, water, lightning, or other acts of nature, unauthorized product modifi cation, or
failure to follow instructions supplied with the product.
□ Repair or attempted repair by anyone not authorized by us.
□ Any damage of the product due to shipment.
□ Removal or installation of the product.
□ Causes external to the product, such as electric power fl uctuation or failure.
□ Use of supplies or parts not meeting our specifi cations.
□ Normal wear and tear.
□ Any other causes which does not relate to a product defect.
■ Removal, installation, and set-up service charges.
Regulatory Notices Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation.
Any changes or modifi cations made to this equipment may void the user’s authority to operate this equipment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
■ Re-position or relocate the receiving antenna.
■ Increase the separation between the equipment and receiver.
■ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
UM-UV-621-M30-Q215V1 www.austin-hughes.com
P.17
P.18
P.19
< Part. 4 >
Options
4.1 Option Table
4.2 48V or 24VDC power
4.3 MIL-type or lockable connector
< Part. 3 >
Specifi cations / OSD / Remote Controller
3.1 Product Specifi cations
3.2 On-screen Display Operation ( OSD )
3.3 Picture In Picture ( PIP ) / Picture By Picture ( PBP )
3.4 Remote Controller ( RC-2 )
P.10 - 11
P.12 - 13
P.14 - 15
P.16
< Part. 1 >
AP-M30 / NAP-M30
1.1 Package Content
1.2 Structure Diagram & Dimension
1.3 Mounting Hardware & Installation
Contents
P. 1
P.2 - 3
P.4 - 5
< Part. 2 >
OP-M30
2.1 Package Content
2.2 Structure Diagram & Dimension
2.3 Mounting Hardware & Installation
P. 6
P.7 - 8
P.9
UM-UV-621-M30-Q215V1 www.austin-hughes.com
■ It is very important to mount the equipment in a suitable cabinet or on a stable surface.
■ Make sure the place has a good ventilation, is out of direct sunlight, away from sources of excessive
dust, dirt, heat, water, moisture and vibration.
The equipment comes with the standard parts shown in package content. Check and make sure they are
included and in good condition. If anything is missing, or damaged, contact the supplier immediately.
Unpacking
Before Installation
How To Clean Your LCD Monitor
Caution :
■ To avoid the risk of electric shock, make sure your hands are dry before unplugging your monitor from or
plugging your monitor into an electrical outlet.
■ When you clean your monitor, do not press down on the LCD screen. Pressing down on the screen can
scratch or damage your display. Pressure damage is not covered under warranty.
■ Use only cleansers made specifi cally for cleaning monitors and monitor screens. Cleansers not made to
clean monitors and monitor screens can scratch the LCD display or strip off the fi nish.
■ Do not spray any kind of liquid directly onto the screen or case of your monitor. Spraying liquids directly
onto the screen or case can cause damage which is not covered under warranty.
■ Do not use paper towels or abrasive pads to clean your monitor. Using an abrasive pad or any wood based
paper product such as paper towels can scratch your LCD screen.
Cleaning Your Monitor
To clean your LCD safely, please follow these steps :
Disconnect the power cord.
Gently wipe the surface using a clean, dry microfi ber cloth. Use as little pressure as possible.
1
2
Cleaning Tough Marks and Smudges
To remove tough marks and smudges, please follow these steps :
Disconnect the power cord.
Spray a small amount of non-abrasive cleanser on a microfi ber cloth.
Gently wipe the surface. Use as little pressure as possible.
Wait until your monitor is completely dry before plugging it in and powering it up.
1
2
Caution : Do not spray or apply any liquids directly onto the monitor. Always apply the solution to your
microfi ber cloth fi rst, not directly on the parts you are cleaning.
3
4
UM-UV-621-M30-Q215V1 www.austin-hughes.com
< 1.1 > Package Content - AP / NAP-M30
P. 1
< Part 1 >
30” Ultra Widescreen LCD display X 1
6ft DVI-D dual-link digital cable
( male to male ) X 1
Power cord X 1
Remote controller X 1
Wall-mount bracket set X 1
AP-M30 / NAP-M30
30” Ultra Widescreen LCD Display
VGA
HDMI
1.4
Audio
in
Power
Audio
out
Basic I/O
Dual-link
DVI-D
Display port
1.2
UM-UV-621-M30-Q215V1 www.austin-hughes.com
Front view
Rear view
Rear case
LCD panel
6mm aluminum front bazel
Audio speaker, pair
LCD membrane
Wall-mount bracket
Remote sensor
1
2
3
4
5
6
Top view
7
7
5
< 1.2 > Structure Diagram - AP / NAP-M30
AP-M30
NAP-M30
P. 2
4
1
2
3
6
Model
Product Dimension
(W x D x H)
Packing Dimension
(W x D x H)
Net
Weight
Gross
Weight
AP-M30
743.9 x 77.5 x 503.4 mm
29.3 x 3.1 x 19.8 inch
To be confi rmed
17.9 kg
39.4 lbs
22.8 kg
50.2 lbs
NAP-M30
743.9 x 77.5 x 503.4 mm
29.3 x 3.1 x 19.8 inch
To be confi rmed
21.9 kg
48.2 lbs
26.8 kg
59 lbs
UM-UV-621-M30-Q215V1 www.austin-hughes.com
< 1.2 > Dimension - AP / NAP-M30
30” Ultra Widescreen LCD Display
P. 3
Front View Side View
Rear View
AP-M30
NAP-M30
UNIT : mm
1mm = 0.03937 inch
Bottom View
UM-UV-621-M30-Q215V1 www.austin-hughes.com
< 1.3 > Wall-mount Installation - AP / NAP-M30
Step
■ Install left & right front wall-mount brackets at
the rear side of the LCD shown above.
■ M5 screw x 8 pcs included ( Left & right side ).
1
Front wall-mount bracket
Rear side
Step
■ Install left & right rear wall-mount brackets on
the wall shown above.
■ 6 x M10 screws required ( Left & right side ).
M10 screw sets are not provided.
2
Rear wall-mount bracket
Wall
Step
■ Attach the LCD to the rear wall-mount brackets
on the wall.
3
Wall
Wall WallLCD
Installation Completed.
Step
4
P. 4
UM-UV-621-M30-Q215V1 www.austin-hughes.com
< 1.3 > VESA Installation - AP / NAP-M30
30” Ultra Widescreen LCD Display
P. 5
M6 screw
■ Hardware and M6*8 pcs for VESA mount are not provided
VESA mount ( 100*100mm )
UM-UV-621-M30-Q215V1 www.austin-hughes.com
30” Ultra Widescreen LCD display X 1
6ft DVI-D dual-link digital cable
( male to male ) X 1
Power cord X 1
Remote controller X 1
VGA
HDMI
1.4
Audio
in
Power
Audio
out
Basic I/O
Dual-link
DVI-D
Display port
1.2
< 2.1 > Package Content - OP-M30
P. 6
< Part 2 >
OP-M30
UM-UV-621-M30-Q215V1 www.austin-hughes.com
< 2.2 > Structure Diagram - OP-M30
Front view
Rear view
Rear case
LCD panel
Universal open frame mounting
Audio speaker, pair
LCD membrane
Extended remote sensor membrane cable
( 66cm from AD board to sensor end )
1
2
3
4
5
Top view
6
6
OP-M30
P. 7
4
Model
Product Dimension
(W x D x H)
Packing Dimension
(W x D x H)
Net
Weight
Gross
Weight
OP-M30
740.9 x 71.5 x 500.4 mm
29.2 x 2.8 x 19.7 inch
To be confi rmed
11.9 kg
26.2 lbs
14.8 kg
32.6 lbs
1
2
5
3
30” Ultra Widescreen LCD Display
UM-UV-621-M30-Q215V1 www.austin-hughes.com
P. 8
Front View Side View
Rear View
< 2.3 > Dimension - OP-M30
OP-M30
UNIT : mm
1mm = 0.03937 inch
Bottom View
UM-UV-621-M30-Q215V1 www.austin-hughes.com
< 2.3 > Installation - OP-M30
30” Ultra Widescreen LCD Display
■ Hardware and M6*8 pcs for VESA mount are not provided
( II ) VESA mount ( 100*100mm )
M6 screw
P. 9
( I ) Universal mount
UM-UV-621-M30-Q215V1 www.austin-hughes.com
< 3.1 > Product Specifi cations
P.10
< Part 3 >
LCD
Panel
Manufacturer
Panel Size ( diagonal ) 30-inch Widescreen TFT color LCD
Display pixel ( dots x lines ) 2560 x 1600
Brightness ( typ. ) 350
Contrast Ratio ( typ. ) 1000:1
Color 1.07 Billion, 10-bit
Viewing Angle ( L/R/U/D ) 89/89/89/89
Response Time ( ms ) 12
Dot pitch ( mm ) 0.2505
Display Area ( mm ) 641.28H x 400.8V
Surface treatment Haze 10%, Hard-coating
Surface hardness 3H
Backlight Type LED
MTBF ( hrs ) 30,000
Mechanical
Design
AP / NAP-M30 OP-M30
Front Panel Black, RAL 9005 -
Rear Casing Black, RAL 9005 Black, RAL 9005
VESA Mounting 100 x 100mm 100 x 100mm
Other Mounting Panel mount Universal mount
Protection 3mm protective glass -
Video
Connectivity
Digital HDMI HDMI 1.4
DVI Dual-link DVI
Display port Display port 1.2
Analog
VGA Analog 0.7Vp-p
Plug & Play DVI / VGA VESA EDID structure 1.3
Synchronization VGA Separate, Composite & SOG
Audio
Connectivity
Audio Input Connector 3.5mm stereo jack
Impedance / Power level 30kΩ / 750mV
Audio Output
Connector 3.5mm stereo jack
Resistance / Power level 30kΩ / 2.8V
Speaker Output Power 2 x 10W
*When the audio output is connected, speaker output is OFF
Power Power Supply
Range
Auto-sensing 100 to 240VAC,
50 / 60Hz
Power Consumption
Screen display ON 70W or less
Power saving mode 5W or less
Power button OFF 2W or less
UM-UV-621-M30-Q215V1 www.austin-hughes.com
Regulatory Safety FCC & CE certifi ed
Physical
Specifi cation
AP-M30 NAP-M30 OP-M30
Product ( W x D x H )
mm
inch
743.9 x 77.5 x 503.4 743.9 x 77.5 x 503.4 740.9 x 71.5 x 500.4
29.3 x 3.1 x 19.8 29.3 x 3.1 x 19.8 29.2 x 2.8 x 19.7
Packing ( W x D x H )
mm
inch
To be confi rmed To be confi rmed To be confi rmed
Net Weight 17.9 kgs / 39.4 lbs 21.9 kgs / 48.2 lbs 11.9 kgs / 26.2 lbs
Gross Weight 22.8 kgs / 50.2 lbs 26.8 kgs / 59 lbs 14.8 kgs / 32.6 lbs
< 3.1 > Product Specifi cations
30” Ultra Widescreen LCD Display
Environmental
Conditions
Operating Temperature 0 to 55°C degree
Humidity 20~90%, non-condensing
Storage
Temperature -5 to 60°C degree
Humidity 5~90%, non-condensing
Shock 10G acceleration (11ms duration)
Vibration 5~500Hz 1G RMS random
Applicable
Format
DVI-D / VGA Input /
Display Port Input
PC Signal 2560 x 1600 x 60Hz
1920 x 1200 x 60Hz
1920 x 1080 x 60Hz
1280 x 1024 x 60Hz
1280 x 720 x 60Hz
1024 x 768 x 60Hz
800 x 600 x 60Hz
HDMI Input
PC Signal Same as VGA
Video Signal
1080p : 50 / 60Hz
1080i : 50 / 60Hz
720p : 50 / 60Hz
480p : 60Hz
576p : 50Hz
Audio Signal 2ch Linear PCM ( 32 / 44.1 / 48 KHz )
P. 11
UM-UV-621-M30-Q215V1 www.austin-hughes.com
Exit the OSD screen
Toggle analog, digital & video connection (DVI-D and video options only)
Display the OSD menu
Power on / off LCD
Power light
Green = On
Flashing Green = Power saving
Orange = Off
Membrane Switch Function
< 3.2 > On-screen Display Operation ( OSD )
Image Settings
Brightness : Adjust background black level of the screen image
Contrast :
Adjust the difference between the image background
(black level) and the foreground (white level)
Sharpness :
Adjust the image from weak to sharp
Scheme : Normal / Vivid / Cinema / Game / Sport
Aspect Ratio :
Adjust the image size
Color temp :
User / 9300k / 6500k / 7500k
1
2
P.12
Geometric
Auto Adjust : Automatically adjust sizes, centers and fi ne tunes the
video signal to eliminate waviness and distortion.
H-Position : Align the screen image left or right
V-Position : Align the screen image up or down
Phase : Adjust the phase value
Clocks/Line :
Adjust the clock value
Auto color :
Automatically adjust colors
Scroll through menu options
UM-UV-621-M30-Q215V1 www.austin-hughes.com
3
PBP Settings
PIP Mode : Adjust picture in picture setting
PIP Position :
Enter into PIP position
PIP Source : Enter into the Sub source and sound source
< 3.2 > On-screen Display Operation ( OSD )
30” Ultra Widescreen LCD Display
Audio Settings
Mute : Turn off the surrounding sound
Volume : Adjust the volume of sound
Main Input : Set the value of treble and bass sound
Main output : Set the main sound output
Pip Input : Set the value of PIP sound input
Pip Output : Set the PIP sound output
4
Setup
Language : Select the language in which the OSD menu is
displayed - English
DCDi : Turn on the DCDi
DLC :
Turn on the DLC
Color Domain : Adjust the RGB color domain
Source Detect : Turn off the auto detection of image signal source
Factory Reset : Return the adjustment back to factory setting
5
P.13
UM-UV-621-M30-Q215V1 www.austin-hughes.com
P.14
< 3.3 > How to Use Picture In Picture ( PIP ) / Picture By Picture ( PBP )
Mode
Display the Sub screen in the Main screen.
PBP Setting → PIP Mode → off / small / small 16:10 / large / large 16:10 / POP 4:3 / POP
Sub screen
Main screen
Position
Adjust the position of the Sub screen ( top left, bottom left, top right, bottom right )
PBP Setting → PIP Position → top left / top right / bottom left / bottom right
top left top right
bottom left bottom right
Size
Adjust the size of the Sub screen
PBP Setting → PIP Mode → small > small 16:10 > large > large 16:10 > POP 4:3 > POP > off
< 3.3.1 > Picture in Picture ( PIP )
UM-UV-621-M30-Q215V1 www.austin-hughes.com
Sub screenMain screen
P.15
Mode
Display the Sub screen next to the Main screen.
PBP Setting → PIP Mode → POP
< 3.3.2 > Picture By Picture ( PBP )
< 3.3.3 > PIP / PBP Source
To select an input signal for PIP / PBP Sub screen.
PBP Setting → PIP Source → VGA / DVI / HDMI / DP
Sub
Main
VGA DVI-D HDMI Display Port
VGA
xoo o
DVI
oxx o
HDMI
oxx o
Display Port
ooo x
The PIP / PBP is operable in the following table :
30” Ultra Widescreen LCD Display
UM-UV-621-M30-Q215V1 www.austin-hughes.com
< 3.4 > Remote Controller ( RC-2 )
P.16
1
2
3
4
5
6
AUTO
0
-/--
7
8 9
PIP
MENU SELECT
BACK
EXIT
SOURCE
POSITION
SWAP
PIP
AUDIO
ASPECT
SLEEP
PIP
ENTER
CH
FREEZE
MUTEINPUT
VOL
W
a
t
e
r
p
r
o
o
f
1
4
3
2
5
7
6
20
21
8
9
10
11
12
13
15
16
17
18
19
14
INPUT Select the source
Switches on or off the TV
0 - 9
[ Reserved for future use ]
AUTO [ Reserved for future use ]
MENU Display the menu on the screen or go to the previous menu
▲ / ▼ / ◄ / ► / ENTER
Go to the upper menu or select the previous value /
Go to the next menu or select the next value /
Decrease the setting value /
Increase the setting value or enter to the select item setting
Enter to the select item settings or excude the setting
BACK [ Reserved for future use ]
MUTE Turn on or off the speaker
Vol + / - Increase or decrease the speaker volume
CH + / - [ Reserved for future use ]
FREEZE [ Reserved for future use ]
- / -- [ Reserved for future use ]
ASPECT [ Reserved for future use ]
SELECT [ Reserved for future use ]
SLEEP [ Reserved for future use ]
EXIT Exit the menu or cancel
PIP functions
PIP
Picture in picture
PIP AUDIO [ Reserved for future use ]
POSITION To set the screen position in PIP mode
SOURCE PIP Source
SWAP Swap screen in PIP mode
1
8
2
3
4
5
6
7
9
10
11
12
13
14
15
16
17
18
19
20
21
UM-UV-621-M30-Q215V1 www.austin-hughes.com
Options AP / NAP OP
MIL-type / lockable connector
DC Power
< 4.1 > Option Table
< Part 4 > Options
P.17
30” Ultra Widescreen LCD Display
UM-UV-621-M30-Q215V1 www.austin-hughes.com
Model 24V 48V
Input rating
Input voltage: 24-Volt 48-Volt
Input range: 18 ~ 36V 36 ~ 75V
Input current
- No load 50 mA 50 mA
- Full load 7022 mA 3511 mA
Output rating
Output voltage: 24-Volt 24-Volt
Output current: 6.25A 6.25A
Effi ciency 89% 89%
< 4.2 > Options : DC Power
P.18
UM-UV-621-M30-Q215V1 www.austin-hughes.com
Input Part no. MIL Standard
MIL - type
Connector
DC Power ***
( Male )
MS3470W8-33P MIL - DTL - 26482
VGA ***
( Male )
MS3470W14-15P MIL - DTL - 26482
Input Part no. Standard
Lockable
Connector
DC Power
( Male )
YM-Ext-461CP001 D-type 3W3
USB LUSB - A111 - 00 -
< 4.3 > Options : MIL-type or Lockable Connector
*** There are several additional MIL DC and VGA connector types with varying design
characteristics to meet cost considerations and to provide users with the most
design fl exibility possible. For more information, please contact us.
*** MIL - type or Lockable connectors above can be integrated with our LCD displays.
Sale service just for connectors not provided.
P.19
30” Ultra Widescreen LCD Display
UM-UV-621-M30-Q215V1 www.austin-hughes.com
The company reserves the right to modify product specifi cations without prior notice and assumes no responsibility
for any error which may appear in this publication.
All brand names, logo and registered trademarks are properties of their respective owners.
Copyright 2015 Austin Hughes Electronics Ltd. All rights reserved.
Loading...