Aussie Vantage 6703C8FKK1 Use Manual
LP Gas Grill Assembly and Use Manual
6703C8FKK1
For Outdoor Household Use Only. Not for Commercial Use.
Need Help? Need to Register Your Grill? Looking for Aussie Parts & Accessories?
Visit us online at www.AussieGrills.com Or call Aussie Customer Service at 1-800-251-7558
WARNING DANGER
! !
• Failure to follow these intsructions could result in
fire or explosion which could cause death, serious
personal injury, or property damage.
• Read and follow instructions carefully before assembly or use.
• Do not use this product for any other purpose than
which it is intended.
• These instructions must be kept with the user.
SAVE THESE INSTRUCTIONS.
WARNING
!
• Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
• An LP cylinder not connected for use shall not be
stored in the vicinity of this or any other appliance.
If you smell gas:
1. Shut off gas to the appliance.
2. Extinquish any open flame.
3. Open lid.
4. If odor continues, keep away from the appliance and immediately call your gas supplier or
your fire department.
2
NOTICE
Meco Corporation strives to be a quality supplier of consumer products. If we omitted
any parts needed for assembly, or you need troubleshooting information, please
contact us using our toll free number or visit our website.
It is important to register your grill and retain your receipt.
1-800-251-7558
8 am - 5 pm E.S.T. Monday - Friday
1-423-639-1171 (Telephone)
1-423-639-2570 (Fax)
CARBON MONOXIDE HAZARD
This appliance can produce carbon monoxide which
has no odor. Using it in an enclosed space can kill
you. Never use this appliance in an enclosed space,
such as a camper, tent, car, or home.
Consumer Service Department
MECO CORPORATION
1500 Industrial R o a d
Greenville, TN 37745 USA
www.aussiegrills.com
DANGER
!
WARNING
!
To reduce the risk of serious bodily injury or death from fire or explosion:
• Never use alcohol, prescription or non-prescription drugs while assembling or safely operating this appliance.
• Do not connect LP Gas Cylinder until assembly is complete.
To reduce the risk of a laceration hazard, wear protective gloves when handling parts that have sharp edges.
Tools Required for Assembly (Supplied with Grill):
CAUTION
!
Phillips Screwdriver
Contents
3
Preparation for Assembly ..............................................3
Packing Lists
Model 6703C8FKK1 ..................................................... 4
Assembly Instructions
Step 1 Left Leg Frame Assembly ............................... 5
Step 2 Left Leg Frame Assembly ............................... 5
Step 3 Cart Frame Assembly.....................................6
Step 4 Wheel Assembly ............................................6
Step 5 Fabric Privacy Panel Assembly .......................7
Step 6 Cylinder Blocking Wire Assembly ...................7
Step 7 Hood/Body To Cart Assembly ........................ 8
Step 8 Side Table Assembly ...................................... 9
Step 9 Side Burner Valve Assembly .........................10
Step 10 Side Burner Igniter Wire Connection ............ 10
Step 11A Side Burner Control Knob Assembly ............ 11
Step 11B Side Burner Grid Assembly .......................... 11
Step 12A Bottom Body Panel Assembly ....................... 11
Step 12B Foil Pan/Grease Pan Assembly ..................... 11
Step 13A Warming Rack Assembly .............................. 12
Step 13B Flame Diffuser Assembly ............................. 12
Step 13C Cooking Grid Assembly ...............................12
Step 14 Battery in Igniter Installation ........................ 12
Connecting/Disconnecting the Gas
Using Gas .................................................................. 13
LP Gas Cylinder ..........................................................13
LP Hose & Regulator ................................................... 14
Connecting LP Gas Cylinder .......................................14
Disconnecting LP Gas Cylinder ............................... 14
How to Perform a Leak Test ........................................ 16
Lighting Grill Using the Pulse-Spark Ignitor ................ 18
Manually Lighting the Grill .........................................20
Lighting the Side Burner .............................................21
Check the Flame ........................................................ 21
Manually Lighting the Side Burner ..............................22
Cooking on the Gas Grill
Grill Cooking (Direct Method) .....................................23
Roasting (Indirect Method) ..........................................24
Warming Rack ............................................................ 25
End of Cooking Session ..............................................25
Care and Maintenance
Cleaning the Grill ....................................................... 26
How to Clean the Burners .......................................... 27
Storage ....................................................................29
Emergencies ............................................................ 30
Troubleshooting.......................................................30
Important Notice- LP Cylinder with OPD ...............32
Replacement Parts
Parts Illustrations ........................................................34
Parts List ...........................................................................35
Limited Warranty.......................................................36
Register your grill and retain your receipt.
Before Using Your Grill
Installation Codes ....................................................... 15
Selecting a Location ................................................... 15
Preparation for Assembly
Remove Grill and all the packaging from carton and place on floor. Make sure there are no loose parts.
NOTE: Before using your grill, read the instructions and your manual.
For easier set-up and assembly, follow instructions of each step in the order they are written as you look at the diagrams. If accessories mentioned in certain assembly steps do not come with your model, skip that step and proceed to
the next step that applies to your model.
If you have any questions or need help, contact Customer Service at 1-800-251-7558 or go to www.aussiegrills.
com. Be sure to have the grill model number and serial number printed on the black label, located on the back edge
of the bottom shelf of the cart. If you need replacement parts, look in the Parts List Section to find the exact parts you
need. If you need a replacement part under warranty, a proof of purchase will be necessary. You will be
asked to forward your proof of purchase via e-mail or to fax your proof of purchase to 423-639-1055 and reference
your model and serial number. It is important to register your grill and retain your receipt.
4
Packing List
Box Description
1 Front Leg- Left
Front Leg- Right
Back Leg- Left
Back Leg- Right
Fabric Privacy Panel
2 Wheels, 2 pcs.
Wheel covers, 2 pcs.
Corner Braces, 4 pcs.
3 Cart Bottom Panel
Cylinder Blocking Wire
4 Side Braces, 2 pcs.
5 Grease Pan
5 Foil Pan
Bottom Panel
6 Hood/Body
7 Left Side Shelf with Side Burner
Right Side Shelf
Side Burner Control Knob
8 Flame Diffuser, 3 pcs.
9 Cooking Grid, 3 pcs.
10 Warming Rack
H Hardware Package
10
9
7
7
8
6
7
Detailed Parts List and Illustrations
may be found on pages 34 & 35.
H
2
6
1
4
2
1
H
2
2
H
3
2
3
2
1
3
5
5
4
2
1
1
Assembly Instructions
Step 1
Left Leg Frame Assembly
Identify Legs by hole placement and lay on floor as shown. Fasten Corner Braces to Legs with 2) 1/4-20 x .50” bolts
each. Attach Brace between legs with 4) 5/32 x .31” bolts each, open side facing up. Closed, flat side of brace will be
flush with outside of legs.
Left Back Leg -
Note hole locations
1/4-20 x .50” Bolt set
4 pcs
5
Left Front legNote hole locations
5/32 x .31” Bolt set
4 pc
VELCRO
Step 2
Right Leg Frame Assembly
Repeat Step 1 for Right Leg pair. Right legs are longer and have no axle hole at bottom.
Right Back Leg -
Note hole locations
1/4-20 x .50” Bolt set
4 pcs
5/32 x .31” Bolt set
4 pc
Right Front legNote hole locations
VELCRO
6 7
Step 3
Cart Frame Assembly
Attach Left Leg Frame and Right Leg Frame to Cart Bottom Panel with eight 1/4-20 x .50” Bolts and eight 1/4-20 x
1.50” Bolts. Fit one Frame onto Bottom Panel at a time and insert the .50” bolts down through the corner brackets into
the Bottom Panel then insert the 1.50” bolts through the Legs into the sides of the Bottom Panel. Tighten all securely.
1/4-20 x .50” Bolt set
8 pc
1/4-20 x 1.50” Bolt set
8 pc
Step 4
Wheel Assembly
Attach the Wheel by first inserting the Axle through the Wheel then the Axle through the Leg. Place the Washer on the
end of the Axle extending out of the opposite side of the Leg. Secure all in place by inserting the Cotter pin through the
hole in the end of the Axle. Snap the Wheel Cover onto the Wheel.
Wheel
Axle
Cotter Pin
Washer
Wheel Cover
Step 5
Fabric Privacy Panel Assembly
Attach the Fabric Privacy Panel between the Front Legs with 6) 5/32” x .31” bolts through the rigid sides of the Panel
into the threaded holes on the inside of the Legs. The bottom corners attach with velcro to the Corner Braces.
5/32 x .31” Bolt set
6 pc
7
WARNING
!
To reduce the risk of serious bodily injury or death from fire or explosion:
Never remove guards or devices to prevent storage of spare or oversize LP Gas Cylinders not recommended for this grill.
Step 6
Cylinder Blocking Wire Assembly
Attach Cylinder Blocking Wire Cabinet Bottom with two 5/32 x .47” Bolts.
5/32 x .47” Bolt
2 pc
8
CAUTION
!
To reduce the risk of bodily injury from lifting, the following assembly steps #s 7 and 8 will require two people.
Step 7
Hood/Body To Cart Assembly
Lift the Hood/Body Assembly over the cart assembly and set it down until it rests on the top of the cart legs.
Align the holes in the side of the Body with the holes in the legs. Insert two 1/4-20 x .50 Bolts through the holes in the
firebox flanges (Back Left Side View) and into threaded inserts in the inside face of the back legs. Insert two 1/4-20
x 1.50 Bolts through the holes in the front legs (Right Side View) and into threaded inserts in firebox flanges. Tighten
after all are installed.
Left Side View
Back
1/4-20 x .50” Bolt set
2 pc
1/4-20 x 1.50” Bolt set
2 pc
Right Side View
CAUTION
!
Prior to performing any further assembly, PERFORM “FIRST TIME USE” LEAK TEST
as detailed on pages 16-17.
If the grill is fully assembled before per forming the First Time Use leak test, the side tables will need to be removed in order to perform the
leak test on the valves behind the knobs, inside the control panel.
Step 8
Side Table Assembly
Screw two 1/4-20 x .50” Bolts into the two bottom threaded inserts on the outside of the Bowl. Do not screw Bolts
A.
all the way. Leave 1/8” of each Bolt exposed.
Align the bottom two holes (“keyhole slots” in detail) on the inner side of the LEFT Side Table with the two bolts threaded partly into the inserts in the Side of the Bowl then slide the Side Burner Table over the Bolts.
B. Holding the Side Burner Table in place, install two 1/4-20 x .50” Bolts from the inside of the Bowl into the two top
threaded holes inthe Side Table.
C. From under the Side Table, install one 5/32 x .31” bolt through the Side Table end into the side of the Bowl.
Repeat this assembly for the RIGHT Side Table. Tighten all bolts.
9
1/4-20 x .50” Bolt set
8 pc
A
Keyhole Slots
5/32 x .31” Bolt set
2 pc
B
C
5/32 x .31” Bolt
10
Step 9
Side Burner Valve Assembly
NOTE: Side Burner Valve is already attached to the regulator hose. Hose is not shown in illustration for clarity.
A. Install the Side Burner Valve from underneath the LEFT Side Table. First insert the valve stem out through the hole in
the bezel and fascia on the front of the side table. Next, flex the tube of the burner down and insert the nozzle into the
opening in the burner tube.
B. Install two 5/32” x .31” Bolts through the Control Knob Bezel and front of Side Table and into the threaded Valve
bracket holes. Install the top bolt first by twisting the valve/bracket to align only the top holes. Do not tighten completely.
Next, twist the valve/bracket to align the bottom holes and install the second bolt. Tighten both.bracket holes.
A
5/32 x .31” Bolt
2 pc
Top Fir st
Valve
Step 10
Side Burner Igniter Wire Connection
The Side Burner Igniter Wire is pre-installed and connected to the Ignition Box. Attach the wire to the Side Burner electrode by sliding the wire
connector onto the electrode terminal.
Underside view of
Side Table/Side Burner
B
Bottom Second
B
Note:
Shown without Regulator
Hose for clarity.
11
Step 11
A. Side Burner Control Knob Assembly
Align the flat keyed hole in the Control Knob with the keyed stem of the Side Burner Valve. Push the Control Knob onto
the Side Burner Valve stem.
B. Side Burner Grid Assembly
Place the Side Burner Grid onto Side Burner Table, allowing the three protruded ends to fall into the three holes around
the Side Burner.
BA
Step 12
A. Bottom Body Panel Assembly
Slide the Bottom Body Panel into the guides of the Body assembly. Secure Bottom Body Panel to Body assembly with
one 5/32 x .47” Bolt and nut on each side.
B. Foil Pan/Grease Pan Assembly
Insert the Foil Pan into the Grease Pan. Slide the Grease Pan into the guides
under the Bottom Body Panel.
5/32 x .47” Bolt
and Nut
2 pc
A
B
Loading...