Aussie 6804T80SS1 User Manual
LP Gas Grill Assembly and Use Manual
6804T80SS1
For Outdoor Household Use Only. Not for Commercial Use.
With the NEW Aussie
FLAVOR ACTIVATOR SYSTEM
(Patent Pending)
Provides:
- More even heat on the cooking surface
- Hotter temperature with the same fuel usage
- Longer cooking for the same amount of fuel
6804T8KSS1
Need Help? Need to Register Your Grill? Looking for Aussie Parts & Accessories?
Visit us online at www.AussieGrills.com Or call Aussie Customer Service at 1-800-251-7558
WARNING
!
• Failure to follow these intructions could result in
fire or explosion which could cause death, serious
personal injury, or property damage.
• Read and follow instructions carefully before assembly or use.
• Do not use this product for any other purpose than
which it is intended.
• These instructions must be kept with the user.
SAVE THESE INSTRUCTIONS.
WARNING
!
• Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
• An LP cylinder not connected for use shall not be
stored in the vicinity of this or any other appliance.
If you smell gas:
1. Shut off gas to the appliance.
2. Extinquish any open flame.
3. Open lid.
4. If odor continues, keep away from the appliance and immediately call your gas supplier or
your fire department.
DANGER
!
2
NOTICE
Meco Corporation strives to be a quality supplier of consumer products. If we omitted
any parts needed for assembly, or you need troubleshooting information, please
contact us using our toll free number or visit our website.
It is important to register your grill and retain your receipt.
1-800-251-7558
8 am - 5 pm E.S.T. Monday - Friday
1-423-639-1171 (Telephone)
1-423-639-2570 (Fax)
www.aussiegrills.com
DANGER
!
CARBON MONOXIDE HAZARD
This appliance can produce carbon monoxide which
has no odor. Using it in an enclosed space can kill
you. Never use this appliance in an enclosed space,
such as a camper, tent, car, or home.
WARNING
!
To reduce the risk of serious bodily injury or death from fire or explosion:
• Never use alcohol, prescription or non-prescription drugs while assembling or safely operating this appliance.
• Do not connect LP Gas Cylinder until assembly is complete except as noted for “first time use” leak test as detailed on pages 17-18.
Consumer Service Department
MECO CORPORATION
1500 Industrial R o a d
Greeneville, TN 37745 USA
CAUTION
!
To reduce the risk of a laceration hazard, wear protective gloves when handling parts that have sharp edges.
To reduce the risk of bodily injury from lifting, assembly will require two people.
Tools Required for Assembly (Supplied with Grill):
Phillips Screwdriver
Packing List
Description
Warming Rack
Cooking Grid, 3 pcs.
Flavor Activators - 4 large, 3 small
Grease Pan
Foil Pan
Left Side Shelf with Side Burner
Side Burner Control Knob
Hood/Body
Right Side Shelf
Bottom Body Panel
Front Crossbar
Cabinet Side Panel- Left
Back Panel Brace wire
Cylinder Retainer Bolt
Cabinet Upright
Cabinet Back Panel
Cylinder Blocking Wire
Cabinet Side Panel- Right
Cabinet Bottom Panel
Drawer Tracks, 2 pcs.
Drawer Body
Locking Caster, 2 pcs.
Fixed Casters, 2 pcs.
Cabinet Door- Left
Drawer Front
Cabinet Door- Right
Door/Drawer handle, 3 pcs
Hardware Package (not pictured)
3
Detailed Parts List and Illustrations
may be found on pages 36 & 37
4
Contents
Packing Lists ................................................................3
Preparation for Assembly .......................................... 4
Assembly Instructions
Step 1 Caster Assembly .........................................5
Step 2 Cabinet Bottom Assembly ...........................5
Step 3 Side Panel Assembly ...................................6
Step 4 Front Crossbar Assembly .............................7
Step 5 Cabinet Upright Assembly ...........................7
Step 6A Cylinder Guard Assembly ............................8
Step 6B Cylinder Blocking Wire Assembly ................8
Step 7 Door Handle Assembly ............................... 8
Step 8 Door Assembly ............................................9
SStep 8 Drawer Track Assembly ............................... 9
Step 9A Drawer Assembly ........................................ 9
Step 9B Drawer Positioning ...................................... 9
Step 10 Door Assembly ..........................................10
Step 11 Hood/Body To Cart Assembly ................... 10
Step 12 Side Table Assembly ................................. 11
Step 13 Side Burner Valve Assembly ...................... 12
Step 14 Side Burner Igniter Wire Connection ......... 12
Step 15A Side Burner Control Knob Assembly .......... 13
Step 15B Side Burner Grid Assembly ....................... 13
Step 16A Bottom Body Panel Assembly ....................13
Step 16B Foil Pan/Grease Pan Assembly .................. 13
Step 17A Warming Rack Assembly ........................... 14
Step 17B Flavor Activator Assembly ......................... 14
Step 17C Cooking Grid Assembly ............................ 14
Step 18 Battery in Igniter Installation ..................... 14
Connecting/Disconnecting the Gas
Using Gas ................................................................ 15
LP Gas Cylinder ..........................................................15
LP Hose & Regulator ................................................... 16
Connecting LP Gas Cylinder ....................................... 16
Disconnecting LP Gas Cylinder ................................... 16
Before Using Your Grill
Installation Codes ....................................................... 17
Selecting a Location ................................................... 17
Performing a Leak Test ............................................... 17
How to Perform a Leak Test ........................................18
Lighting Grill Using the Pulse-Spark Ignitor ................ 20
Manually Lighting the Grill .........................................22
Lighting the Side Burner .............................................23
Check the Flame ........................................................ 23
Manually Lighting the Side Burner ..............................24
Cooking on the Gas Grill
Grill Cooking (Direct Method) .....................................25
Roasting (Indirect Method) .......................................... 26
Rotisserie Cooking ...................................................... 27
Warming Rack ............................................................ 28
End of Cooking Session ..............................................28
Care and Maintenance
Cleaning the Grill ....................................................... 29
How to Clean the Burners ..........................................30
Storage ....................................................................32
Emergencies ............................................................ 33
Troubleshooting.......................................................33
Important Notice- LP Cylinder with OPD ...............35
Replacement Parts
Parts Illustrations ........................................................ 36
Parts List ...........................................................................37
Limited Warranty.......................................................38
Register your grill and retain your receipt.
Preparation for Assembly
Remove grill and all the packaging from carton and place on floor. Make sure there are no loose parts.
NOTE: Before using your grill, read the instructions and your manual.
For easier set-up and assembly, follow instructions of each step in the order they are written as you look at the diagrams. If accessories mentioned in certain assembly steps do not come with your model, skip that step and proceed to
the next step that applies to your model.
If you have any questions or need help, contact Customer Service at 1-800-251-7558 or go to www.aussiegrills.
com. Be sure to have the grill model number and serial number printed on the black label located inside the left door of
the cabinet. If you need replacement parts, look in the Parts List Section to find the exact parts you need. If you need
a replacement part under warranty, a proof of purchase will be necessary. You will be asked to forward your
proof of purchase via e-mail or to fax your proof of purchase to 423-639-1055 and reference your model and serial
number. It is important to register your grill and retain your receipt.
5
Assembly Instructions
Step 1
Caster Assembly
Lay Cabinet Bottom Panel upside down, so that the flat surface is on the floor. Assemble Fixed Casters to the LEFT Side
(the side closest to the cutouts) of Cabinet Bottom Panel and Swivel Lock Casters to the RIGHT Side of Cabinet Bottom
Panel. Insert 1/4-20 x .60” Bolts through the caster bracket holes into the threaded holes in the Cabinet Bottom Panel.
Tighten the bolts. Push the lever on the two Locking Casters to lock so the caster wheels do not roll.
Fixed Casters
1/4-20 x .60” Bolt set
16 p c
Swivel Lock Casters
Step 2
A. Cabinet Bottom Assembly
With Back Panel on floor, place Cabinet Bottom Panel against Back Panel edge and align the holes. Install three
1/4-20 x .50 Bolts through the holes and secure with three 1/4-20 Nuts.
1/4-20 x .50” Bolt set
3 pcs
6 7
Step 3
Side Panel Assembly
Attach Left Side Panel and Right Side Panel to Cabinet Bottom Panel with six 1/4-20 x .50” Bolts and 1/4-20 Nuts.
1/4-20 x .50” Bolt set
6 pc
Secure Left and Right Side Panels to Back Panel with four 5/32 x .31” Bolts through the inside of the Back Panel.
5/32 x .31” Bolt set
4 pc
Step 4
Front Crossbar Assembly
Turn cart assembly up on casters. Attach Front Crossbar, with the triangle braces facing down and the flat surface to
the front, to Side Panels with six 1/4-20 x .50” Bolts into the threaded holes in the top inside ends of Side Panels.
front crossbar
1/4-20 x .50” Bolt set
6 pc
7
Step 5
Cabinet Upright Assembly
Attach Cabinet Upright to Cabinet Bottom and Front Crossbar with four 5/32 x .31” Bolts. Orient Upright so that Matchholder/Chain is closest to top of cabinet (Front Crossbar).
5/32 x .31” Bolt set
4 pc
8
WARNING
!
To reduce the risk of serious bodily injury or death from fire or explosion:
• Never remove guards or devices to prevent storage of spare or oversize LP Gas Cylinders not recommended for
this grill.
Step 6
A. Cylinder Guard Assembly
Attach Wire Guard to Front Crossbar and Back Panel with two 5/32 x .47” Bolts.
B. Cylinder Blocking Wire Assembly
Attach Cylinder Blocking Wire to Right Side Panel with one 5/32 x .47” Bolt and nut. Attach to Bottom Panel with one
5/32 x .47” Bolt.
A
5/32 x .47” Bolt set
4 pc
5/32 Nut
1 pc
B
Step 7
Door Handle Assembly
Assemble Handle to Left Door using two 5/32 x .31” Bolts. Repeat with Right Door.
Note: 2 extra screws provided.
nut
5/32 x .31” Bolt set
4 pc
Step 8 Model 6805 & 6804 with drawer
Drawer Track Assembly and Cylinder Retaining Bolt Installation
A.
Attach one Drawer Track to Back Panel and Cabinet Upright using four 5/32 x .31” Bolts. Attach other Drawer Track
to Back Panel and Right Side Panel using four 5/32 x .31” Bolts.
B. Install the Cylinder Retainer Bolt through the hole in the back of the Bottom Shelf into the nut welded underneath.
A
5/32 x .31” Bolt set
8 pc
9
B
Step 9 Model 6805 & 6804 with drawer
A. Drawer Assembly
Assemble Handle to Drawer Front with two 5/32 x .31” Bolts. Note: 1 extra screw provided.
Attach Drawer Front to Drawer Body with sIX 5/32 x .31” Bolts into threaded holes in inside of Drawer Front.
5/32 x .31” Bolt set
8 pc
Cylinder Retainer Bolt
A
drawer
front
B
B. Drawer Positioning
Slide Drawer Assembly over the Drawer Tracks to position the Drawer.
10
Step 10
Door Assembly
Install LEFT Door. Drop bottom door pin into Cabinet Bottom Panel hole. Swing top of door toward hole in top of Left
Side Panel. Depress spring-loaded pin with thumb while sliding pin into Left Side Panel hole until it snaps into place.
Right Door assembly is similar; Fixed pin is under drawer and inserts into hole in door and spring-loaded pin is in the
BOTTOM of small door and functions the same.
Depress
Left Door shown,
Right Door same.
CAUTION
!
To reduce the risk of bodily injury from lifting, the following assembly steps #s 9 and 10 will require two people.
Step 11
Hood/Body To Cart Assembly
Lift the Hood/Body Assembly over the cart assembly and set it down until it rests on the inside top flanges of the cart.
Align the holes in the side of the Hood/Body with the holes in the Side Panel brackets. Insert four 1/4-20 x .50 Bolts
through the holes in cabinet flanges and into threaded inserts in firebox and tighten after all are installed.
Right side
view
1/4-20 x .50” Bolt set
4 pc
11
CAUTION
!
Prior to performing any further assembly, PERFORM “FIRST TIME USE” LEAK TEST
as detailed on pages 17-18.
If the grill is fully assembled before per forming the First Time Use leak test, the side tables will need to be removed in order to perform the
leak test on the main burner valves inside the control panel, behind the knobs, .
Step 12
Side Table Assembly
Screw two 1/4-20 x .50” Bolts into the two bottom threaded inserts on the outside of the Bowl. Do not screw Bolts
A.
all the way. Leave 1/8” of each Bolt exposed.
Align the bottom two holes (“keyhole slots” in detail) on the inner side of the LEFT Side Table with the two bolts threaded partly into the inserts in the Side of the Bowl then slide the Side Burner Table over the Bolts.
B. Holding the Side Burner Table in place, install two 1/4-20 x .50” Bolts from the inside of the Bowl into the two top
threaded holes in the Side Table.
C. From under the Side Table, install one 5/32 x .31” bolt through the Side Table end into the side of the Bowl.
Repeat this assembly for the RIGHT Side Table. Tighten all bolts.
1/4-20 x .50” Bolt set
8 pc
5/32 x .31” Bolt set
2 pc
A
Keyhole Slots
B
C
5/32 x .31” Bolt
12
CAUTION
To avoid possible damage to grill, DO NOT ATTEMPT TO LIFT GRILL BY THE SIDE TABLES
Step 13
Side Burner Valve Assembly
NOTE: Side Burner Valve is already attached to the regulator hose.
A. Install the Side Burner Valve from underneath the LEFT Side Table. First insert the valve stem out through the hole
in the bezel and fascia on the front of the side table. Next, flex the tube of the burner down and insert the nozzle into
the opening in the burner tube.
B. Install two 5/32” x .31” Bolts through the Control Knob Bezel and front of Side Table and into the threaded Valve
bracket holes. Install the top bolt first by twisting the valve/bracket to align only the top holes. Do not tighten completely.
Next, twist the valve/bracket to align the bottom holes and install the second bolt. Tighten both.
A
5/32 x .31” Bolt
2 pc
Valve
Step 14
Side Burner Igniter Wire Connection
The Side Burner Igniter Wire is pre-installed and connected to the Ignition Box. Attach the wire to the Side Burner
electrode by sliding the wire connector onto the electrode
terminal.
Underside view of
Side Table/Side Burner
Top Fir st
B
Bottom Second
Note:
Shown without Regulator
Hose for clarity.
Loading...