AU Optronics T420HW02-V0 Product Specification

www.smarterglass.com
978 997 4104
sales@smarterglass.com
Product Description: T420HW02 V0 TFT-LCD PANEL
AUO Model Name: T420HW02 V0
Customer Part No/Project Name
:
Customer Signature Date AUO Date
Reviewed By: Jr Chiou
Prepared By: Stanley Chiang
Document Version: 1.0
Date:2008/2/1
©Copyright AU Optronics, Inc. January, 2008 All Rights Reserved. T420HW02 V0 0/29 No Reproduction and Redistribution Allowed
Product Functional Specification
42” Full-HD Color TFT-LCD Module
Model Name: T420HW02 V0
(*) Preliminary Specification
( ) Final Specification
Note : This specification is subject to change without notice.
©Copyright AU Optronics, Inc. January, 2008 All Rights Reserved. T420HW02 V0 1/29 No Reproduction and Redistribution Allowed
COVER
Contents
ITEM No
RECORD OF REVISIONS
CONTENTS
GENERAL DESCRIPTION 1
ABSOLUTE MAXIMUM RATINGS 2
ELECTRICAL SPECIFICATIONS 3
ELECTRICAL CHARACTREISTICS 3-1
INTERFACE CONNECTIONS 3-2
SIGNAL TIMING SPECIFICATIONS 3-3
SIGNAL TIMING WAVEFORMS 3-4
COLOR INPUT DATA REFERNECE 3-5
POWER SEQUENCE 3-6
RELIABILITY 6
7
INTERNATIONAL STANDARDS
SAFETY 7-1
EMC 7-2
8
PACKING
PRECAUTIONS 9
©Copyright AU Optronics, Inc. January, 2008 All Rights Reserved. T420HW02 V0 2/29 No Reproduction and Redistribution Allowed
OPTICAL SPECIFICATIONS 4
MECHANICAL CHARACTERISTICS 5
Record of Revision
Version
1.0 2008/2/1 First release
Date No Old Description New Description Remark
©Copyright AU Optronics, Inc. January, 2008 All Rights Reserved. T420HW02 V0 3/29 No Reproduction and Redistribution Allowed
1. General Description
This specification applies to the 42 inch Color TFT-LCD Module T420HW02 V0. This LCD module has
a TFT active matrix type liquid crystal panel 1920x1080 pixels, and diagonal size of 42 inch. This
module supports 1920x1080 Full-HD mode (Non-interlace).
Each pixel is divided into Red, Green and Blue sub-pixels or dots which are arranged in vertical stripes.
Gray scale or the brightness of the sub-pixel color is determined with a 8-bit gray scale signal for each
dot.
The T420HW02 V0 has been designed to apply the 8-bit 2 channel LVDS interface method. It is
intended to support displays where high brightness, wide viewing angle, high color saturation, and
high color depth are very important.
*
General Information
Items Specification Unit Note
Active Screen Size 42.02 inches
Display Area 930.24(H) x 523.26(V) mm
Outline Dimension 983.0(H) x 576.0(V) x 52.7(D)
Driver Element a-Si TFT active matrix
Display Colors 16.7M Colors
Number of Pixels 1920 x 1080 Pixel
Pixel Pitch 0.4845 mm
Pixel Arrangement RGB vertical stripe
Display Mode Normally Black
Lamp quantity, type 18pcs, Straight type pcs
mm With inverter
Surface Treatment Anti-Glare coating (Haze 11%)
Hard coating (3H)
©Copyright AU Optronics, Inc. January, 2008 All Rights Reserved. T420HW02 V0 4/29 No Reproduction and Redistribution Allowed
Bandwidth : 10~500Hz
Absolute Maximum Ratings
The following are maximum values which, if exceeded, may cause faulty operation or damage to the
unit.
Item Symbol
Power Supply Input Voltage VDD -0.3 14 [Volt] 1
Logic Input Voltage Vin -0.3 3.6 [Volt] 1
BLU Input Voltage V
BLU Brightness Control Voltage
Ambient Operating
Temperature
Ambient Operating Humidity HOP 10 80 [%RH] 2
Storage Temperature TST -20 +60 [oC] 2
Storage Humidity HST 10 80 [%RH] 2
Shock (non-operation) - 50 G 3
Vibration (non-operation) - 1.5 G 4
Thermal shock -20 60 C 5
Note 1 : Duration = 50msec
Note 2 : Maximum Wet-Bulb should be 50 and No condensation.
DDB
-0.3 26.4 [Volt] 1
BLON -0.3 3.6 [Volt] 1
TOP 0 +50 [oC] 2
Min Max Unit Note
Note 3 : Half sine wave, shock level : 50G(11ms), direction : ±x, ±y, ±z (one time each direction)
Note 4 : Wave form : Random, vibration level : 1.5G RMS,
Duration : X,Y,Z 30min (one time each direction)
Note 5 : -20C/1hr ~ 60C/1hr, 100 cycles
©Copyright AU Optronics, Inc. January, 2008 All Rights Reserved. T420HW02 V0 5/29 No Reproduction and Redistribution Allowed
Differential Input
High Threshold
Voltage
2. Electrical Specification
The T420HW02 requires two power inputs. One is employed to power the LCD electronics and to drive
the TFT array and liquid crystal. The second input, which powers the CCFL, is typically generated by
an inverter.
3-1 Electrical Characteristics
Values Parameter Symbol
Min Typ Max
LCD:
Power Supply Input Voltage Vdd 10.8 12 13.2 Vdc
Power Supply Input Current Idd - 1 A 1
Power Consumption Pc - 12 Watt 1
Inrush Current I
LVDS
Interface
Differential Input
Low Threshold
Voltage
Common Input
Voltage
Input High
- - 4 A 5
RUSH
VTH +100 mV
VTL -100 mV
V
CIM
0.6 1.2 1.8 V
VIH
2.0 3.3 Vdc CMOS
Unit Notes
4
4
Interface
Backlight Power Consumption
Life Time 50000
The performance of the Lamp in LCM, for example life time or brightness, is extremely influenced
by the characteristics of the DC-AC Inverter. So all the parameters of an inverter should be
carefully designed so as not to produce too much leakage current from high-voltage output of the
inverter. When you design or order the inverter, please make sure unwanted lighting caused by
the mismatch of the lamp and the inverter (no lighting, flicker, etc) never occurs. When you
confirm it, the LCD Assembly should be operated in the same condition as installed in your
instrument.
©Copyright AU Optronics, Inc. January, 2008 All Rights Reserved. T420HW02 V0 6/29 No Reproduction and Redistribution Allowed
Threshold Voltage
Input Low
Threshold Voltage
(High)
VIL
(Low)
- 175 184 Watt 2
0 0.8 Vdc
60000 Hours
3
s
µ
s
µ
Do not attach a conducting tape to lamp connecting wire. If the lamp wire attach to conducting
tape, TFT-LCD Module have a low luminance and the inverter has abnormal action because
leakage current occurs between lamp wire and conducting tape.
The relative humidity must not exceed 80% non-condensing at temperatures of 40 or less. At
temperatures greater than 40, the wet bulb temperature must not exceed 39. When operate
at low temperatures, the brightness of CCFL will drop and the lifetime of CCFL will be reduced.
Note :
1. Vdd=12.0V, fv=60Hz, f
pattern
2. The Backlight power consumption shown above does include loss of external inverter at 25.
The used lamp current is the lamp typical current
3. The life is determined as the time at which luminance of the lamp is 50% compared to that of
initial value at the typical lamp current on condition of continuous operating at 25±2.
4. VCIM = 1.2V
CLK
=80 Mhz , 25, Vdd Duration time= 470
, Test pattern : white
VTH
VCIM
VTL
0V
Figure : LVDS Differential Voltage
5. Measurement Condition: Rising time = 470μs
GND
0.1 Vdd
470
0.9 Vdd
Vdd
©Copyright AU Optronics, Inc. January, 2008 All Rights Reserved. T420HW02 V0 7/29 No Reproduction and Redistribution Allowed
3-2 Interface Connections
-
LCD connector: FI-RE51S-HF (JAE) or equivalent
No Symbol Description
1 GND Ground
2 NC No connection
3 NC No connection
4 NC No connection
5 NC No connection
6 Reserved
7 LVDS SEL LVDS order
8 NC No connection
9 Reserved
10 Reserved
11 GND Ground
12 RO 0N FIRST CHANNEL 0-
13 RO 0P FIRST CHANNEL 0+
14 RO 1N FIRST CHANNEL 1-
15 RO 1P FIRST CHANNEL 1+
No Symbol Description
27 GND Ground
28 RE0N SECOND CHANNEL 0-
29 RE0P SECOND CHANNEL 0+
30 RE1N SECOND CHANNEL 1-
31 RE1P SECOND CHANNEL 1+
32 RE 2N SECOND CHANNEL 2-
33 RE 2P SECOND CHANNEL 2+
34 GND Ground
35 RECLKN SECOND CLOCK CHANNEL C-
36 RECLKP SECOND CLOCK CHANNEL C+
37 GND Ground
38 RE3N SECOND CHANNEL 3-
39 RE3P SECOND CHANNEL 3+
40 NC No connection
41 NC No connection
16 RO 2N FIRST CHANNEL 2-
17 RO 2P FIRST CHANNEL 2+
18 GND Ground
19 ROCLKN FIRST CLOCK CHANNEL C-
20 ROCLKP FIRST CLOCK CHANNEL C+ 46 GND Ground
21 GND Ground
22 RO 3N FIRST CHANNEL 3-
23 RO 3P FIRST CHANNEL 3+
24 NC No connection
25 NC No connection
26 GND Ground
Note: 1. All GND (ground) pin should be connected together to the LCD module’s metal frame.
2. All V
( power input ) pins should be connected.
LCD
42 GND Ground
43 GND Ground
44 GND Ground
45 GND Ground
47 NC No connection
48 VLCD Power Supply +12V
49 VLCD Power Supply +12V
50 VLCD Power Supply +12V
51 VLCD Power Supply +12V
- - -
©Copyright AU Optronics, Inc. January, 2008 All Rights Reserved. T420HW02 V0 8/29 No Reproduction and Redistribution Allowed
LVDS Option = HighJEIDA
Previous Cycle Current Cycle Next Cycle
Clock
RIN0+
RIN0-
RIN1+
RIN1-
RIN2+
RIN2-
RIN3+
RIN3-
LVDS Option = Low/OpenNS
Previous Cycle Current Cycle Next Cycle
Clock
G7
R2R7 G2G2R2R3 R4R5R6 R3
G3B2 B3B3G3G4 G5G6 G4
B4NA DEDEB4B5 B6B7NA B5
R0B1 NANAR0R1 G0G1B0 R1
RIN0+
RIN0-
RIN1+
RIN1-
RIN2+
RIN2-
RIN3+
RIN3-
R0R5 G0G0R0R1 R2R3R4 R1
G1B0 B1B1G1G2 G3G4G5 G2
B2NA DEDEB2B3 B4B5NA B4
R6B7 NANAR6R7 G6G7B6 R7
©Copyright AU Optronics, Inc. January, 2008 All Rights Reserved. T420HW02 V0 9/29 No Reproduction and Redistribution Allowed
Backlight Connector Pin Configuration
1. Electrical specification
No
1 Input Voltage V
2 Input Current I
3 Input Power P
4 Input inrush current
ITEM SYMBOL CONDITION MIN TYP MAX UNIT Note
--- 21.6 24.0 26.4 V
DDB
DDB
DDB
I
RUSH
5 Output Frequency FBL V
ON/OFF Control
6
Voltage
V
BLO N
ON V
OFF
ON/OFF Control
7
I
V
BLON
Current
External PWM
8
Control Voltage
EV
PWM
MAX
MIN --- 0 --- 0.8 V
V
=24V
DDB
100% Brightness
V
=24V
DDB
100% Brightness
V
=24V
DDB
100% Brightness
=24V ---
DDB
=24V 2.0 --- 3.3 V
DDB
V
=24V 0.0 --- 0.8 V
DDB
=24V 0 --- 2 mA
DDB
--- 2.0 --- 3.3 V
6.9 7.3 7.7 A
--- 175 184 W
---
--- 10 A
62 --- kHz
DC
DC
DC
DC
DC
DC
DC
DC
External PWM
9
Control Current
External PWM Duty
10
Ratio
External PWM
11
Frequency
Internal PWM
12
Control Voltage
EI
PWM
ED
EF
MAX
PWM=100% 0 --- 2 mA
MIN PWM=30% 0 --- 2 mA
--- 20
PWM
--- 140 --- 240 Hz
PWM
IV
V
PWM
=24V 0 --- 3.3 V
DDB
Ta=25±5, Turn on for 45minutes
--- 100 %
DC
DC
DC
©Copyright AU Optronics, Inc. January, 2008 All Rights Reserved. T420HW02 V0 10/29 No Reproduction and Redistribution Allowed
2. Input specification
Connector 1: S14B-PH-SM3-TB(JST) or equivalent
Pin No
1 V
2 V
3 V
4 V
5 V
6 BL
7 BL
8 BL
9 BL
10 BL
Symbol Description
DDB
Operating Voltage Supply, +24V DC regulated
DDB
Operating Voltage Supply, +24V DC regulated
DDB
Operating Voltage Supply, +24V DC regulated
DDB
Operating Voltage Supply, +24V DC regulated
DDB
Operating Voltage Supply, +24V DC regulated
GND
Ground and Current Return
GND
Ground and Current Return
GND
Ground and Current Return
GND
Ground and Current Return
GND
Ground and Current Return
11 Det Output of Detect error: Low=NG , Open/High=OK
12 V
BLON
BL On-Off: Open/High (3.3V) for BL On as default
External PWM (AC Signal Control Duty);
13 P
DIM
(2)
Internal PWM (DC Power Control Duty, 0~3.3V); Open/High (+3.3V, 100% Duty) for 100%
14
P
DIM
Selection
GND: External PWM dimming;
(3,4)
Open/High (3.3V): Internal PWM dimming.
Note (1) Det is Output pin for detect power error. Note (2) P
DIM
is PWM duty control input for +3.3V TTL level signal or DC voltage by Pin 14 input. This input signal is (a) continuous pulse signal with +3.3V, TTL level signal spec, or (b) DC power with 0~3.3V. If this is Open or +3.3V, 100% duty (i.e. +3.3V, DC level), backlight should perform 100% luminance. Duty ratio of this input signal should be proportional relationship in certain range of control without any kind of inherent side effect like waterfall effect on screen. Guaranteed duty range and dimming ratio should be specified with supplementary measurement result.
Note (3) Pin 14 is the selection pin for PWM control method; if this pin is connected to GND, PDIM
input of Pin 13 should have logic level duty signal for PWM control. If this is set to High or Open, Pin 13 should have DC level signal therefore the Inverter should have Saw Tooth Wave Generator to generate internal PWM signal. Default setting is “Not Connected”, Pin 13 of PWM control should have DC Level signal for PWM.
Note (4) Pin 14 selection vs. Pin 11/13 control function table:
Pin 14 = GND
Pin 14 = Open/High
Default: Open/High: 100%
(AC Signal Control Duty)
(DC Power Control Duty)
Pin 13
External PWM
Internal PWM
©Copyright AU Optronics, Inc. January, 2008 All Rights Reserved. T420HW02 V0 11/29 No Reproduction and Redistribution Allowed
Slave Board:
Connector 2: S12B-PH-SM3-TB(JST) or equivalent
Pin No
1 V
2 V
3 V
4 V
5 V
6 BL
7 BL
8 BL
9 BL
10 BL
11 NC
12 NC
Symbol Description
DDB
Operating Voltage Supply, +24V DC regulated
DDB
Operating Voltage Supply, +24V DC regulated
DDB
Operating Voltage Supply, +24V DC regulated
DDB
Operating Voltage Supply, +24V DC regulated
DDB
Operating Voltage Supply, +24V DC regulated
GND
Ground and Current Return
GND
Ground and Current Return
GND
Ground and Current Return
GND
Ground and Current Return
GND
Ground and Current Return
©Copyright AU Optronics, Inc. January, 2008 All Rights Reserved. T420HW02 V0 12/29 No Reproduction and Redistribution Allowed
3-3 Signal Timing Specifications
This is the signal timing required at the input of the User connector. All of the interface signal timing
should be satisfied with the following specifications for it’s proper operation.
Timing Table (DE only Mode)
Vertical Frequency Range A (60Hz)
Signal Item Symbol Min Type
Period Tv 1090 1130 1200 Th
Active Tdisp (v) 1080 Th
Vertical Section
Horizontal Section
Clock
Vertical Frequency Frequency Vs 57 60 63 Hz
Horizontal Frequency Frequency Hs 65.4 67.8 72 KHz
Vertical Frequency Range B (50Hz)
Signal Item Symbol Min Type
Blanking Tblk (v) 10 50
Period Th 1030 1100 1180 Tclk
Active Tdisp (h) 960 Tclk
Blanking Tblk (h) 70 140
Period CLK 13.41
Frequency Freq 67.362 74.58 84.96 MHz
Period Tv 1316 1356 1436 Th
Max Unit
120 Th
220 Tclk
Max Unit
ns
Vertical Section
Horizontal Section
Clock
Vertical Frequency Frequency Vs 47 50 53 Hz
Horizontal Frequency Frequency Hs 65.8 67.8
©Copyright AU Optronics, Inc. January, 2008 All Rights Reserved. T420HW02 V0 13/29 No Reproduction and Redistribution Allowed
Active Tdisp (v) 1080 Th
Blanking Tblk (v) 236 276
Period Th 1030 1100 1180 Tclk
Active Tdisp (h) 960 Tclk
Blanking Tblk (h) 70
Period CLK 13.41
Frequency Freq 67.774 74.58 84.134 MHz
356 Th
140 220 Tclk
ns
71.3 KHz
3-4 Signal Timing Waveforms
RGB Data
(even)
RGB Data
(odd)
DE
CLK
RGB
Data
DE
Pixel
M-6
Pixel
M-4
Pixel
M-2
Pixel
M
Invalid Data
Pixel
2
Pixel
4
Pixel
6
Pixel
8
Pixel
10
Pixel
12
Pixel
M-7
Pixel
M-5
Pixel
M-3
Pixel
M-1
Invalid Data
Pixel
1
Pixel
3
Pixel
5
Pixel
7
Pixel
9
Pixel
11
Tclk
Tdisp(h) Tblk(h)
Th
Line
N
Invalid Data Invalid Data
Line
1
Line
2
Line
3
Line
4
Th
Tv
Tdisp(v)Tblk(v)
Pixel
M-4
Pixel
M-2
Pixel
M
Invalid Data
Pixel
2
Pixel
4
Pixel
M-5
Pixel
M-3
Pixel
M-1
Line
N
Invalid Data
Pixel
1
Pixel
3
©Copyright AU Optronics, Inc. January, 2008 All Rights Reserved. T420HW02 V0 14/29 No Reproduction and Redistribution Allowed
3-5 Color Input Data Reference
The brightness of each primary color (red, green and blue) is based on the 8 bit gray scale data input
for the color; the higher the binary input, the brighter the color. The table below provides a reference for
color versus data input.
COLOR DATA REFERENCE
Color
Basic
Color
RED
Input Color Data
RED
MSB LSB
R7 R6 R5 R4 R3 R2 R1 R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 B6 B5 B4 B3 B2 B1 B0
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Red(255) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Green(255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
Blue(255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
Cyan 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Magenta 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
Yellow 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
RED(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
RED(001) 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
----
RED(254) 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
MSB LSB
GREEN
BLUE
MSB LSB
RED(255) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
GREEN
BLUE
©Copyright AU Optronics, Inc. January, 2008 All Rights Reserved. T420HW02 V0 15/29 No Reproduction and Redistribution Allowed
GREEN(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
GREEN(001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0
----
GREEN(254) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0
GREEN(255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
BLUE(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
BLUE(001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
-------
BLUE(254) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0
BLUE(255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
3-6 Power Sequence
1. Power sequence of panel
Values
Parameter
t1 0.47 - 30 ms
t2 0.1 - 50 ms
t3 500 - - ms
t4 100 - - ms
t5 0.1 - 50 ms
t6 - 30 ms
t7 1000 - - ms
Apply the lamp voltage within the LCD operating range. When the backlight turns on before the LCD
operation or the LCD turns off before the backlight turns off, the display may momentarily become
abnormal.
Caution : The above on/off sequence should be applied to avoid abnormal function in the display. In
case of handling, make sure to turn off the power when you plug the cable into the input connector or
Min. Typ. Max.
Units
pull the cable out of the connector.
©Copyright AU Optronics, Inc. January, 2008 All Rights Reserved. T420HW02 V0 16/29 No Reproduction and Redistribution Allowed
2. Power sequence of inverter
Values Parameter
Min. Typ. Max.
T1 20 - - ms
T2 500 - - ms
T3 250 - - ms
T4 0 - - ms
T5 1 - - ms
T6 10 ms
©Copyright AU Optronics, Inc. January, 2008 All Rights Reserved. T420HW02 V0 17/29 No Reproduction and Redistribution Allowed
Units
4. Optical Specification
Optical characteristics are determined after the unit has been ‘ON’ and stable for approximately 60
minutes in a dark environment at 25. The values specified are at an approximate distance 50cm
from the LCD surface at a viewing angle of Φ and θequal to 0°.
SR3 or equivalent
Fig.4-1 Optical measurement equipment and method
Parameter
Symbol
Values
Min. Typ. Max.
Units Notes
Contrast Ratio CR 2000 2500 1
Surface Luminance, white LWH 400 500
Luminance Variation
Response Time (Average)
δ
WHITE
5p 1.3 3
Tγ
6.5 ms 4,5 (Gray to Gray)
cd/
2
Color Coordinates
RED RX 0.640
RY 0.330
GREEN GX 0.290
GY 0.600
Typ.-0.03
Typ.+0.03
BLUE BX 0.150
BY 0.060
WHITE WX 0.280
WY
0.290
Viewing Angle Contrast Ratio>10
x axis, right(φ=0°)
x axis, left(φ=180°)
y axis, up(φ=90°)
y axis, down (φ=0°)
θ
θ θ θ
r
l
u
d
89 Degree 6
89
89
89
©Copyright AU Optronics, Inc. January, 2008 All Rights Reserved. T420HW02 V0 18/29 No Reproduction and Redistribution Allowed
Contrast ratio (CR)=
Note:
1. Contrast Ratio (CR) is defined mathematically as:
Brightness on the "white" state Brightness on the "black" state
2. Surface luminance is luminance value at point 1 across the LCD surface 50cm from the surface with
all pixels displaying white. From more information see Fig. 4-2. When V
LWH=L
, Where L
on1
is the luminance with all pixels displaying white at center 1 location.
on1
3V/4
V/2
V/4
Fig.4-2 Optical measurement point
3. The variation in surface luminance,
δ
WHITE(5P)
=Maximum(L
δ
is defined under 100% brightness as:
WHITE
, L
on1
on2
,…,L
)/Minimum(L
on5
DDB
= 24V, I
H
1
H/2 H/4
, L
on1
on2
,…L
DDB
3H/4
on5
= 6.4A.
V
)
©Copyright AU Optronics, Inc. January, 2008 All Rights Reserved. T420HW02 V0 19/29 No Reproduction and Redistribution Allowed
4. Response Time:
(a) G-to-G: average response time among brightness of 0%, 25%, 50%, 75% &100%.
0% 25% 50% 75% 100%
0%
25%
50%
75%
100%
tr: 0%25% tr: 0%50% tr: 0%75% tr: 0%100%
tf: 25%0% tr: 25%50% tr: 25%75% tr: 25%100%
tf: 50%0% tf: 50%25% tr: 50%75% tr: 50%100%
tf: 75%0% tf: 75%25% tf: 75%50% tr: 75%100%
tf: 100%0% tf: 100%25% tf: 100%50% tf: 100%75%
5. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are determined
for the horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the
LCD surface. For more information see Fig. 4-3. (Optical measurement by SR3)
Fig.4-3 Viewing Angle Definition
©Copyright AU Optronics, Inc. January, 2008 All Rights Reserved. T420HW02 V0 20/29 No Reproduction and Redistribution Allowed
5. Mechanical Characteristics
The contents provide general mechanical characteristics for the model T420HW02. In addition the
figures in the next page are detailed mechanical drawing of the LCD.
Outline Dimension
Active Display Area
Weight 15000g (Max.)
Surface Treatment Anti-Glare coating (Haze 11%)
Horizontal (typ.) 983.0mm
Vertical (typ.) 576.0mm
Depth (typ.) 52.7mm (with inverter)
Horizontal (typ.) 939.0mm Bezel Area
Vertical (typ.) 531.26mm
Horizontal 930.24mm
Vertical 523.26mm
Hard coating (3H)
©Copyright AU Optronics, Inc. January, 2008 All Rights Reserved. T420HW02 V0 21/29 No Reproduction and Redistribution Allowed
2D drawing
©Copyright AU Optronics, Inc. January, 2008 All Rights Reserved. T420HW02 V0 22/29 No Reproduction and Redistribution Allowed
©Copyright AU Optronics, Inc. January, 2008 All Rights Reserved. T420HW02 V0 23/29 No Reproduction and Redistribution Allowed
6. Reliability
Environment test condition
No Test Item Condition
1 High temperature storage test
2 Low temperature storage test
3 High temperature/High humidity test
4 High temperature operation test
5 Low temperature operation test
Vibration test
6
(non-operating)
Shock test
7
(non-operating)
Vibration test
8
(with carton)
Drop test
9
(with carton)
Ta=60, 300hr judge
Ta=-20, 300hr judge
Ta=50, 80%RH, 300hr judge
Ta=50, 300hr judge
Ta=0, 300hr judge
Wave form: random
Vibration level : 1.5G RMS
Bandwidth : 10-500Hz
Duration: X, Y, Z 10min one time each direction
Shock level: 50G
Waveform: half sine wave, 11ms
Direction: ±X, ±Y, ±Z One time each direction
Time cycle no.: once for each time
Random wave (1.5Grms 10~200Hz)
30mins / Per each X.Y.Z axes
Height: 31 cm
1 corner, 3 edges, 6 surfaces
(ASTMD4169-I)
©Copyright AU Optronics, Inc. January, 2008 All Rights Reserved. T420HW02 V0 24/29 No Reproduction and Redistribution Allowed
7. International Standard
7-1. Safety
(1) UL60065, Underwriters Laboratories, Inc. (AUO file number : E204356)
Standard for Safety of Information Technology Equipment Including electrical Business
Equipment.
(2) CSA E60065, Canadian Standards Association
Standard for Safety of Information Technology Equipment Including Electrical Business
Equipment.
(3) IEC 60065 ver. 7th,European Committee for Electro technical Standardization (CENELEC)
EUROPEAN STANDARD for Safety of Information Technology Equipment Including Electrical
Business Equipment.
7-2. EMC
(1) ANSI C63.4 “Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and
Electrical Equipment in the Range of 9kHz to 40GHz. “American National standards
Institute(ANSI), 1992
(2) C.I.S.P.R “Limits and Methods of Measurement of Radio Interface Characteristics of Information
Technology Equipment.” International Special committee on Radio Interference.
(3) EN 55022 “Limits and Methods of Measurement of Radio Interface Characteristics of Information
Technology Equipment.” European Committee for Electrotechnical Standardization. (CENELEC),
1998
©Copyright AU Optronics, Inc. January, 2008 All Rights Reserved. T420HW02 V0 25/29 No Reproduction and Redistribution Allowed
Module
1pcs Module/ESD Bag
3pcs Modules
Cushion set
3pcs / 1 carton
(2) Packing
Packing Instruction
Package information:
Carton outside dimension : 1087x285x716mm
Carton/Package weight : 3kg
©Copyright AU Optronics, Inc. January, 2008 All Rights Reserved. T420HW02 V0 26/29 No Reproduction and Redistribution Allowed
AU
O
ptronics
T420HW02 V0
97.42T04.0XX
Shipping label
Green Mark Description:
Model No: T420HW02 V0
For Pb Free products, AUO will add
for identification.
For RoHS compatible products, AUO will add for identification.
Note: The Green Mark will be present only when the green documents have been ready by AUO
Internal Green Team. (The definition of green design follows the AUO green design checklist.)
Carton label
MODEL NO:
PART NO:
CUSTOMER NO:
CARTON NO:
Made in Taiwan
*PM100 - 01A1600001*
QTY: 3
Pallet information
By air cargo : : (4x1) x2 layers, one pallet put 8 boxes, total 24 pcs module.
By sea : (4x1) x3 layers, one pallet put 12 boxes, total 36 pcs module.
Pallet dimension : 1150x1100x120mm
Pallet weight : 10kg
By air total weight : 40.8 kg/box X 8 boxes=326.4 kg (with pallet weight 336.4kg)
By sea total weight : 40.8 kg/box X 12 boxes=489.6 kg (with pallet weight 499.6kg)
Corner angle
Stretch film
Label
Moisture-proof film
PET band
Corner angle
Pallet
©Copyright AU Optronics, Inc. January, 2008 All Rights Reserved. T420HW02 V0 27/29 No Reproduction and Redistribution Allowed
(3) PRECAUTIONS
Please pay attention to the followings when you use this TFT LCD module.
9-1 MOUNTING PRECAUTIONS
(1) You must mount a module using holes arranged on back side of panel.
(2) Please attach the surface transparent protective plate to the surface in order to protect the
polarizer. Transparent protective plate should have sufficient strength in order to the resist
external force.
(3) You should adopt radiation structure to satisfy the temperature specification.
(4) Acetic acid type and chlorine type materials for the cover case are not desirable because the
former generates corrosive gas of attacking the polarizer at high temperature and the latter
causes circuit break by electro-chemical reaction.
(5) Do not touch, push or rub the exposed polarizers with glass, tweezers or anything harder than
HB pencil lead. And please do not rub with dust clothes with chemical treatment. Do not touch
the surface of polarizer for bare hand or greasy cloth. (Some cosmetics are detrimental to the
polarizer.)
(6) When the surface becomes dusty, please wipe gently with absorbent cotton or other soft
materials like chamois soaks with petroleum benzene. Normal-hexane is recommended for
cleaning the adhesives used to attach front/ rear polarizers. Do not use acetone, toluene and
alcohol because they cause chemical damage to the polarizer.
(7) Wipe off saliva or water drops as soon as possible. Their long time contact with polarizer
causes deformations and color fading.
(8) Do not open the case because inside circuits do not have sufficient strength.
9-2 OPERATING PRECAUTIONS
(1) The spike noise causes the mis-operation of circuits. It should be lower than following voltage:
V=±200mV(Over and under shoot voltage)
(2) Response time depends on the temperature. (In lower temperature, it becomes longer..)
(3) Brightness depends on the temperature. (In lower temperature, it becomes lower.) And in
lower temperature, response time (required time that brightness is stable after turned on)
becomes longer.
(4) Be careful for condensation at sudden temperature change. Condensation makes damage to
polarizer or electrical contacted parts. And after fading condensation, smear or spot will occur.
(5) When fixed patterns are displayed for a long time, remnant image is likely to occur.
(6) Module has high frequency circuits. Sufficient suppression to the electromagnetic interference
©Copyright AU Optronics, Inc. January, 2008 All Rights Reserved. T420HW02 V0 28/29 No Reproduction and Redistribution Allowed
shall be done by system manufacturers. Grounding and shielding methods may be important
to minimize the interface.
9-3 ELECTROSTATIC DISCHARGE CONTROL
Since a module is composed of electronic circuits, it is not strong to electrostatic discharge. Make
certain that treatment persons are connected to ground through wrist band etc. And don’t touch
interface pin directly.
9-4 PRECAUTIONS FOR STRONG LIGHT EXPOSURE
Strong light exposure causes degradation of polarizer and color filter.
9-5 STORAGE
When storing modules as spares for a long time, the following precautions are necessary.
(1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the
temperature between 5 and 35 at normal humidity.
(2) The polarizer surface should not come in contact with any other object. It is recommended that
they be stored in the container in which they were shipped.
9-6 HANDLING PRECAUTIONS FOR PROTECTION FILM
(1) The protection film is attached to the bezel with a small masking tape. When the protection film
is peeled off, static electricity is generated between the film and polarizer. This should be
peeled off slowly and carefully by people who are electrically grounded and with well ion-blown
equipment or in such a condition, etc.
(2) When the module with protection film attached is stored for a long time, sometimes there
remains a very small amount of flue still on the Bezel after the protection film is peeled off.
(3) You can remove the glue easily. When the glue remains on the Bezel or its vestige is
recognized, please wipe them off with absorbent cotton waste or other soft material like
chamois soaked with normal-hexane.
©Copyright AU Optronics, Inc. January, 2008 All Rights Reserved. T420HW02 V0 29/29 No Reproduction and Redistribution Allowed
Loading...