AU Optronics T216XW01-V3 Product Specification

www.jxlcd.com

Document Version : 0.5

Date : 2009/11/18

www.braemac.co.uk sales@braemac.co.uk

Tel: 01925 419090 Fax: 01925 419091

Document Version : 0.5

Date : 2009/11/18

Product Specifications

21.6” WXGA Color TFT-LCD Module Model Name: T216XW01 V3

( ) Preliminary Specifications

(*) Final Specifications

www.jxlcd.com

www.braemac.co.uk sales@braemac.co.uk

Tel: 01925 419090 Fax: 01925 419091

Contents

No ITEM

COVER

CONTENTS

RECORD OF REVISIONS

1 GENERAL DESCRIPTION

2 ABSOLUTE MAXIMUM RATINGS

3 ELECTRICAL SPECIFICATIONS

3-1 ELECTRICAL CHARACTERISTICS

3-2 INTERFACE CONNECTIONS

3-3 SIGNAL TIMING SPECIFICATIONS

3-4 SIGNAL TIMING WAVEFORMS

3-5 COLOR INPUT DATA REFERENCE

3-6 POWER SEQUENCE for LCD

4 OPTICAL SPECIFICATIONS

5 MECHANICAL CHARACTERISTICS

5-1 FRONT VIEW

5-2 REAR VIEW

6 RELIABILITY

7 INTERNATIONAL STANDARDS

7-1 SAFETY

7-2 EMC

7-3 GREEN

8 PACKING

8-1 PACKING INSTRUCTION

8-2 PALLET INFORMATION

8-3 SHIPPING LABEL

8-4 CARTON LABEL

9 PRECAUTIONS

9-1 MOUNTING PRECAUTIONS

9-2 OPERATING PRECAUTIONS

www.jxlcd.com

9-3 ELECTROSTATIC DISCHARGE CONTROL

9-4 PRECAUTIONS FOR STRONG LIGHT EXPOSURE

9-5 STORAGE

9-6 HANDLING PRECAUTIONS FOR PROTECTION FILM

www.braemac.co.uk sales@braemac.co.uk

Tel: 01925 419090 Fax: 01925 419091

Record Revision

Version Date No Old Description New Description Remark

0.0 2009/8/20 First Draft

0.1 2009/9/28 15 Color coordinate: White (0.285, 0.293) Color coordinate: White (0.280, 0.290) update 8 Update pin1, pin2, pin3, pin20 note update 19,20 Update 2D drawing update 27 Add Appendix for EDID information add 10 Update lamp spec update

0.2 2009/10/12 10 Update lamp spec update 24 Update label information update

0.3 2009/10/16 14 Update Power Sequence update

0.4 2009/11/12 8 Update LVDS connector update

0.5 2009/11/18 21 Update vibration test condition update

www.jxlcd.com

www.braemac.co.uk sales@braemac.co.uk

Tel: 01925 419090 Fax: 01925 419091

1. General Description

This specification applies to the 21.6 inch Color TFT-LCD Module T216XW01. This LCD module has a TFT

active matrix type liquid crystal panel with 1,366x768 pixels, and the diagonal size is 21.6 inches. This module

supports 1,366x768 XGA-WIDE mode (Non-interlace).

Each pixel is divided into Red, Green and Blue sub-pixels or dots which are arranged in vertical stripes. Gray

scale or the brightness of the sub-pixel color is determined with an 8-bit gray scale signal for each dot.

The T216XW01 has been designed to apply to 8-bit and 1 channel LVDS interface method. It is intended to

support displays where high brightness, wide viewing angle, high color saturation, and high color depth are

very important.

This module is not equipped with inverter board for backlight.

* General Information

Item Specification Unit Note

Active Screen Size 21.6 Inch

Display Area 477.417 (H) x 268.416 (V) mm

Outline Dimension

Resolution 1,366 x 768 pixel

Pixel Pitch 0.3495 mm

Pixel Arrangement RGB vertical stripe

Display mode Normally Black

Display Colors 16.7M (8-bit for R,G,B) color

Typical White Luminance 350 @ 8 mA [cd/m2]

Surface Treatment AG, Haze=11%, 3H

Green RoHS compliance

www.jxlcd.com

501 (H)



297 (V)  17.3 (D)

mm w/o Inverter

www.braemac.co.uk sales@braemac.co.uk

Tel: 01925 419090 Fax: 01925 419091

2. Absolute Maximum Ratings

The following are maximum values which, if exceeded, may cause faulty operation or damage to the unit.

Item Symbol Min Max Unit Note

Logic/LCD Drive Voltage Vdd -0.3 6 [Volt] 1

Input Voltage of Signal Vin -0.3 3.6 [Volt] 1

Operating Temperature TOP 0 +50 [oC] 2

Operating Humidity HOP 10 90 [%RH] 2

Storage Temperature TST -20 +60 [oC] 2

Storage Humidity HST 10 90 [%RH] 2

Note

1, Duration = 50 msec

к

2, Maximum Wet-Bulb should be 39

and No condensation.

www.jxlcd.com

www.braemac.co.uk sales@braemac.co.uk

Tel: 01925 419090 Fax: 01925 419091

μ

3. Electrical Specification

The T216XW01 requires two power inputs. One is employed to power the LCD electronics and to drive the

TFT array and liquid crystal. An inverter typically generates the second input, which powers the CCFL.

3-1 Electrical Characteristics

Parameter Symbol

Min Typ Max

Values

Unit Note

LCD:

Power Supply Input Voltage Vcc 4.5 5.0 5.5 Vdc

Power Supply Input Current Icc - 0.8 1.0 A 1

Power Consumption Pc - 4.0 5.0 Watt 1

Inrush Current I

Backlight Power Consumption - 22.27 22.81 Watt 2

Total Power Consumption - 26.27 27.81 Watt

Life Time 50,000 - - Hours 5,6

NoteΚ

1. Vcc=5.0V, Fv=60Hz, Fclk= 85.0 MHz , 25

s

2. Vcc rising time = 470

www.jxlcd.com

3. The performance of the Lamp in LCM, for example: lifetime or brightness, is extremely influenced by

www.jxlcd.com

the characteristics of the DC-AC Inverter. So all the parameters of an inverter should be carefully

designed so as not to produce too much leakage current from high-voltage output of the inverter.

When you design or order the inverter, please make sure unwanted lighting caused by the mismatch

of the lamp and the inverter (no lighting, flicker, etc) never occurs. When you confirm it, the LCD

Assembly should be operated in the same condition as installed in your instrument.

, Vcc=5.0V

- - 3 A 1

RUSH

к

. , Test Pattern : White Pattern

4. Do not attach a conducting tape to lamp connecting wire. If the lamp wire attach to conducting tape,

TFT-LCD Module have a low luminance and the inverter has abnormal action because leakage

current occurs between lamp wire and conducting tape.

5. The relative humidity must not exceed 80% non-condensing at temperatures of 40

к

temperatures greater than 40

low temperatures, the brightness of CCFL will drop and the lifetime of CCFL will be reduced.

6. The life is determined as the time at which luminance of the lamp is 50% compared to that of initial

value at the typical lamp current on condition of continuous operating at 25 ± 2 . The lamp current

should fix at 8 mA (typ.) and then keep the 50,000hr(min.) lamp life

www.braemac.co.uk sales@braemac.co.uk

, the wet bulb temperature must not exceed 39к. When operate at

Tel: 01925 419090 Fax: 01925 419091

к

or less. At

3-2 Interface Connectionsʳ

Ё

LCD connector (CN1): P-TWO 196282-33041

Pin No Symbol Description Note

1 Reserved No connect AUO internal test pin

2 SCL EEPROM Serial Clock

3 SDA EEPROM Serial Data

4 GND Ground

5 Rx0- LVDS Channel 0 [Polarity: Negative]

6 Rx0+ LVDS Channel 0 [Polarity: Positive]

7 GND Ground

8 Rx1- LVDS Channel 1 [Polarity: Negative]

9 Rx1+ LVDS Channel 1 [Polarity: Positive]

10 GND Ground

11 Rx2- LVDS Channel 2 [Polarity: Negative]

12 Rx2+ LVDS Channel 2 [Polarity: Positive]

13 GND Ground

14 RXCLK- LVDS Clock [Polarity: Negative]

ʳ

ʳʳ

15 RXCLK+ LVDS Clock [Polarity: Positive]

16 GND Ground

17 Rx3- LVDS Channel 3 [Polarity: Negative]

18 Rx3+ LVDS Channel 3 [Polarity: Positive]

www.jxlcd.com

19 GND Ground

20 Panel_SEL Panel_SEL

21 LVDS Option* Low for JEIDA, High/Open for NS

22 WP

23 GND Ground

24 GND Ground

25 GND Ground

26 Vdd (+5V) 5V, DC, Regulated

27 Vdd (+5V) 5V, DC, Regulated

28 Vdd (+5V) 5V, DC, Regulated

29 Vdd (+5V) 5V, DC, Regulated

30 Vdd (+5V) 5V, DC, Regulated

NoteΚ

High(3.3V) for writable, Low (GND) for Protection

1, All GND (ground) pins should be connected together and should also be connected to the LCD’s metal

frame.

2, All Vcc (power input) pins should be connected together.

www.braemac.co.uk sales@braemac.co.uk

Tel: 01925 419090 Fax: 01925 419091

* LVDS Option = L (GND) ÎÎÎÎ JETDA Format

Previous Cycle Current Cycle Next Cycle

Clock

RIN0+ RIN0-

RIN1+ RIN1-

RIN2+ RIN2-

RIN3+

RIN3-

* LVDS Option = H (3.3V) or N.C.ÎÎÎÎ NS Format

www.jxlcd.com

Clock

Previous Cycle Current Cycle Next Cycle

G7

R2R7 G2G2R2R3 R4R5R6 R3

G3B2 B3B3G3G4 G5G6 G4

B4NA DEDEB4B5 B6B7NA B5

R0B1 NANAR0R1 G0G1B0 R1

RIN0+ RIN0-

RIN1+ RIN1-

RIN2+ RIN2-

RIN3+

RIN3-

www.braemac.co.uk sales@braemac.co.uk

Tel: 01925 419090 Fax: 01925 419091

R0R5 G0G0R0R1 R2R3R4 R1

G1B0 B1B1G1G2 G3G4G5 G2

B2NA DEDEB2B3 B4B5NA

B3

R6B7 NANAR6R7 G6G7B6 R7

* Backlight Connector Pin Configuration

Ё

Electrical specification (Lamp spec)

Parameter Min Typ Max Units Condition Note

CCFL Current (ICFL) 7 8 9 [mA] rms

CCFL Frequency (FCFL) 40 46 80 [KHz]

CCFL Ignition Voltage (Vs) 1,270 [Volt] rms

CCFL Ignition Voltage (Vs) 1,450 [Volt] rms

CCFL Voltage (Reference) (VCFL) 671 696 735 [Volt] rms

CCFL Power Consumption (PCFL) 22.27 26.46 [Watt]

Κ

Note

1, CCFL Operation Current: Operation range from 5mA to 9mA .

2, Start-up Voltage means the lowest voltage (after output capacitor) at lighting on stable time under darkness

environment (under 0.1 lux).

3, Start-up Voltage means the lowest voltage (after output capacitor) at lighting on stable time under lightness

environment (over 500 lux).

ʳ

(Ta=25

(Ta= 25

(Ta= 0

(Ta=25

к

к к

к

)

1

2

3

4

5

4, CCFL Voltage is base on following current, 735Vrms @7.0mA; 696Vrms @8.0mA; 671Vrms @9mA.

5, PCFL = ICFL x VCFL x 4 = 8 x 696 x 4 = 22.27 W (typ)

PCFL = ICFL x VCFL x 4 = 9 x 735 x 4 = 26.46 W (max)

* Lamp configuration

www.jxlcd.com



www.braemac.co.uk sales@braemac.co.uk

Tel: 01925 419090 Fax: 01925 419091



3-3 Signal Timing Specifications

This is the signal timing required at the input of the User connector. All of the interface signal timings should be

satisfied with the following specifications for the proper operation.

* Timing Table

Signal Item Symbol Min. Typ. Max. Unit

Period Tv 784 810 1,015 Th Ver t ical Section

Horizontal

Section

LVDS Clock Frequency Fclk (1/Tclk) 50 80 86 MHz

Ver t ical

Frequency

Horizontal

Frequency

NoteΚ

Active Tdisp(v) 768 Th

Blanking Tblk (v) 8 42 247 Th

Period Th 1,460 1,648 2,000 Tclk

Active Tdisp(h) 1,366 Tclk

Blanking Tblk (h) 48 282 634 Tclk

Frequency Fv 47 60 63 Hz

Frequency Fh 43 48 53 kHz

1, CLK signal input must be valid while power supply is applied.

2, Display position is specific by the rise of DE signal only. Horizontal display position is specified by the falling

st

edge of 1

specified by the rise of DE after a “Low” level period equivalent to eight times of horizontal period. The 1

corresponding to one horizontal line after the rise of DE is displayed at the top line of screen.

3, If a period of DE “High” is less than 1,366 CLK or less than 768 lines, the rest of the screen displays black.

4, The display position does not fit to the screen if a period of DE “High” and the effective data period do not

synchronize with each other.

CLK right after the rise of DE, is displayed on the left edge of the screen. Vertical display position is

www.jxlcd.com

st

data

www.braemac.co.uk sales@braemac.co.uk

Tel: 01925 419090 Fax: 01925 419091

3-4 Signal Timing Waveforms

RGB Dat a

DE

1366

Pixel

Invalid Data

CLK

Tcl k

RGB

Dat a

Line

768

Invalid Data Invalid Data

DE

Line

Pixel

1

Pix el

2

Pixel

3

Pixel

4

www.jxlcd.com

Pi xel

www.jxlcd.com

5

Pixel

6

1366

Pix el

Invalid Data

Tdisp(h)

Th

1

Line

2

Line

3

Line

4

Line

768

Th

Tdis p(v)

Tv

Pix el

1

Pix el

2

www.braemac.co.uk sales@braemac.co.uk

Tel: 01925 419090 Fax: 01925 419091

3-5 Color Input Data Reference

The brightness of each primary color (red, green and blue) is based on the 8 bit gray scale data input for the

color. The higher the binary input, the brighter the color. The table below provides a reference for color versus

data input.

* COLOR DATA REFERENCE

Color

Basic Color

RED

Input Color Data

RED

MSB LSB

R7 R6 R5 R4 R3 R2 R1 R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 B6 B5 B4 B3 B2 B1 B0

Black(L0) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

Red(255) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

Green(255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0

Blue(255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1

Cyan 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

Magenta 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1

Yellow 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0

White(L255) 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

RED(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

RED(001) 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

----

RED(254) 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

RED(255) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

GREEN(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

www.jxlcd.com

MSB LSB

GREEN

BLUE

MSB LSB

GREEN

BLUE

GREEN(001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0

----

GREEN(254) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0

GREEN(255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0

BLUE(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

BLUE(001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1

-------

BLUE(254) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0

BLUE(255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1

www.braemac.co.uk sales@braemac.co.uk

Tel: 01925 419090 Fax: 01925 419091

3-6 Power Sequence

Parameter

Min. Type. Max.

t1 0.4 --- 30 ms

t2 0.1 --- --- ms

t3 200 --- --- ms

t4 0*1 --- --- ms

t5 0 --- --- ms

t6 --- --- ---*2 ms

t7 500 --- --- ms

www.jxlcd.com

t2a 10 --- 100 ms

www.jxlcd.com

t2b 0*3 --- 100*3 ms

Note: (1) T4=0 : concern for residual pattern before BLU turn off. (2) T6 : voltage of VDD must decay smoothly after power-off. (customer system decide this value) (3) T2b : customer decide this value

Values

Unit

www.braemac.co.uk sales@braemac.co.uk

Tel: 01925 419090 Fax: 01925 419091

4. Optical Specification

Optical characteristics are determined after the unit has been ‘ON’ and stable for approximately 30 minutes in a

dark environment at 25

viewing angle of

к

. The values specified are at an approximate distance 50cm from the LCD surface at a

ӥ

and Ӱequal to 0.

SR3 or equivalent

Fig.4-1 Optical measurement equipment and method

Parameter Symbol

Contrast Ratio CR 2,000 2,500 1

Surface Luminance, white LWH 300 350

Luminance Variation

Response Time

Color Gamut 72 %

Color Coordinates

www.jxlcd.com

RED RX 0.640

R

GREEN GX 0.290

G

BLUE BX 0.150

B

WHITE WX 0.280

Ӭ

WHITE

9 p 1.3 3

T

ӫ

0.330

Y

0.600

Y

0.060

Y

Min. Typ. Max.

6.5 ms 4

Typ.-0.03

Value

Typ.+0.03

Unit Note

cd/

ф

2

Ӱ

Ӱ Ӱ Ӱ

Y

r

l

u

d

65 88 Degree 5

55 88 Degree 5

Tel: 01925 419090 Fax: 01925 419091

W

Viewing Angle by ELDIM Contrast Ratio>10

x axis, right(ӽ=0)

x axis, left(ӽ=180)

y axis, up(ӽ=90)

y axis, down (

www.braemac.co.uk sales@braemac.co.uk

ӽ=0

)

0.290

NoteΚ

1, Contrast Ratio (CR) is defined mathematically as:

Contrast Ratio=

2, Surface luminance is luminance value at point 1 across the LCD surface 50cm from the surface with all

pixels displaying white. From more information see FIG 4-2. When I

Where Lon1 is the luminance with all pixels displaying white at center 1 location.

www.jxlcd.com

Fig.4-2 Luminance

Surface Luminance of L

= 32 mA, LWH=350cd/ф(typ.) LWH=Lon1,

BL

on1

off1

3, The variation in surface luminance,

Ӭ

WHITE(9P)

www.braemac.co.uk sales@braemac.co.uk

=Maximum(L

V/2

V/6

Ӭ

WHITE is defined (center of Screen) as:

, L

on1

,…,L

on2

1 2 3

4 5 6

7 8

Fig.4-3 Luminance Variation

)/Minimum(L

on9

H

H/2 H/6

Tel: 01925 419090 Fax: 01925 419091

on1

, L

9

on2

,…L

)

on9

V

4, Response time T

luminance ratio (0%,25%,50%,75%,100% brightness matrix) and is based on f

ʳ

5, Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are determined for the

horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the LCD surface. For

more information see FIG 4-5.

ӫ

is the average time required for display transition by switching the input signal for five

=60Hz to optimize.

v

0% 25% 50% 75% 100%

0%

25%

50%

75%

100%

ʳ

t

25%-0%

t

50%-0%

t

75%-0%

t

100%-0%

t

0%-25%

t

50%-25%

t

75%-25%

t

100%-25%

ʳ

t

0%-50%

t

25%-50%

t

75%-50%

t

100%-50%

ʳ

t

0%-75%

25%-75%

t

50%-75%

ʳ

100%-75%

t

0%-100%

t

25%-100%

t

50%-100%

t

75%-100%

ʳ

www.jxlcd.com

Fig.4-4 Viewing Angle Definition

www.braemac.co.uk sales@braemac.co.uk

Tel: 01925 419090 Fax: 01925 419091

5. Mechanical Characteristics

The contents provide general mechanical characteristics for the model T216XW01. In addition the figures in the

next page are detailed mechanical drawing of the LCD.

Horizontal (typ.) 501mm

Outline Dimension

Bezel Area

Active Display Area

Weight 2,350g (typ.)

Surface Treatment HC, 3H

www.jxlcd.com

Vertical (typ.) 297mm

Depth (typ.) 17.3mm

Horizontal (typ.) 481mm

Vertical (typ.) 272.5mm

Horizontal 477.417mm

Vertical 268.416mm

www.braemac.co.uk sales@braemac.co.uk

Tel: 01925 419090 Fax: 01925 419091

5-1 Front View (2D drawing)

www.jxlcd.com

www.braemac.co.uk sales@braemac.co.uk

Tel: 01925 419090 Fax: 01925 419091

5-2 Rear View (2D drawing)

www.jxlcd.com

˸Κ

Not 1, Assembly lamp connecter type : YEONHO 35001HS-02L

www.braemac.co.uk sales@braemac.co.uk

Tel: 01925 419090 Fax: 01925 419091

6. Reliability ʳ

Ё

Environment test condition

ʳ

1 High Temperature Storage 3

2 Low Temperature Storage 3

3 High Temperature Operation 3

4 Low Temperature Operation 3

5 Vibration (non-operation) 3

6 Shock (non-operation) 3

7 Vibration (With carton) 3

8 Drop (With carton) 3

ʳ

ʳʳ

Test Items Q'ty Conditions

60

к

300 hrs

-20

к

, 300 hrs

50

к

, 300 hrs

-5

к

, 300 hrs

Wave form: random Vibration level: 1.5G RMS Bandwidth: 10-300Hz, Duration: X, Y, Z 30min One time each direction Shock level: 50G Waveform: half sine wave, 11ms Direction: ±X,±Y, ±Z One time each direction Random wave (1.5 Grms 10~200Hz) 30mins / Per each X.Y.Z axes Height: 45.7cm 1 corner, 3 edges, 6 surfaces (ASTMD4169-I)

www.jxlcd.com

www.braemac.co.uk sales@braemac.co.uk

Tel: 01925 419090 Fax: 01925 419091

7. International Standard

7-1 Safety

1, UL6500, Underwriters Laboratories, Inc. (AUO file number : E204356)

Standard for Safety of Information Technology Equipment Including electrical Business Equipment.

2, CAN/CSA C22.2 No. 950-95 Third Edition, Canadian Standards Association, Jan. 28, 1995

Standard for Safety of Information Technology Equipment Including Electrical Business Equipment.

3, EN60950 : 1992+A2: 1993+A2: 1993+C3: 1995+A4: 1997+A11: 1997

IEC 950: 1991+A1: 1992+A2: 1993+C3: 1995+A4:1996

IEC 60065

European Committee for Electro technical Standardization (CENELEC)

EUROPEAN STANDARD for Safety of Information Technology Equipment Including Electrical Business

Equipment.

7-2. EMC

1, ANSI C63.4 “Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and

Electrical Equipment in the Range of 9kHz to 40GHz. “American National standards Institute(ANSI), 1992

2, C.I.S.P.R “Limits and Methods of Measurement of Radio Interface Characteristics of Information

Technology Equipment.” International Special committee on Radio Interference.

3, EN 55022 “Limits and Methods of Measurement of Radio Interface Characteristics of Information

Technology Equipment.” European Committee for Electrotechnical Standardization. (CENELEC), 1998

7-3 Green 

Green Mark Description:

1, For Pb Free products, AUO will add

2, For RoHS compatible products, AUO will add

Note

：

The Green Mark will be present only when the green documents have been ready by AUO Internal Green Team. (The definition of green design follows the AUO green design checklist.)

www.jxlcd.com





for identification.

www.braemac.co.uk sales@braemac.co.uk

Tel: 01925 419090 Fax: 01925 419091

8. Packing

8-1 Packing Instruction

www.jxlcd.com

8-2 Pallet Information

By air & by sea (3*2)*2 layers, 12 boxes in a pallet, total 108 pcs of module in a pallet

Dimension

Κ

1,150 * 910 * 1,944 mm

Stretch film

Bottom cardboard

Label

Pallet Dimension

Top cardboard

Κ

1,150 * 910 * 138 mm

PET band

Corner angle

Wooden pallet

www.braemac.co.uk sales@braemac.co.uk

Tel: 01925 419090 Fax: 01925 419091

8-3 Shipping Label

*xxxxxxxxxxxx

Panel Unique ID

-xxxx*

AUO Internal Use

XXXXX Model NO: T216XW01 V.3 XXXXXXX Manufactured XX

AUO Internal Use

Green mark description

(1) For Pb Free Product, AUO will add (2) For RoHs compatible products, AUO will add RoHS for identification. Note: The green Mark will be present only when the green documents have been ready by AUO internal green team. (definition of green design follows the AUO green design checklist.)

AU Optronics

/XX MADE IN XXXXX

Week

Year

www.jxlcd.com

AUO Internal Use

for identification.

Factory Location

8-4 Carton Label

QTY :





www.braemac.co.uk sales@braemac.co.uk

Tel: 01925 419090 Fax: 01925 419091

9. PRECAUTIONS

Please pay attention to the followings when you use this TFT LCD module.

9-1 MOUNTING PRECAUTIONS

1, You must mount a module using holes arranged in four corners or four sides.

2, You should consider the mounting structure so that uneven force (ex. Twisted stress) is not applied to

module. And the case on which a module is mounted should have sufficient strength so that external

force is not transmitted directly to the module.

3, Please attach the surface transparent protective plate to the surface in order to protect the polarizer.

Transparent protective plate should have sufficient strength in order to the resist external force.

4, You should adopt radiation structure to satisfy the temperature specification.

5, Acetic acid type and chlorine type materials for the cover case are not desirable because the former

generates corrosive gas of attacking the polarizer at high temperature and the latter causes circuit break

by electro-chemical reaction.

6, Do not touch, push or rub the exposed polarizers with glass, tweezers or anything harder than HB pencil

lead. And please do not rub with dust clothes with chemical treatment. Do not touch the surface of

polarizer for bare hand or greasy cloth. (Some cosmetics are detrimental to the polarizer.)

7, When the surface becomes dusty, please wipe gently with absorbent cotton or other soft materials like

chamois soaks with petroleum benzene. Normal-hexane is recommended for cleaning the adhesives

used to attach front/ rear polarizers. Do not use acetone, toluene and alcohol because they cause

chemical damage to the polarizer.

8, Wipe off saliva or water drops as soon as possible. Their long time contact with polarizer causes

deformations and color fading.

9, Do not open the case because inside circuits do not have sufficient strength.

9-2 OPERATING PRECAUTIONS

1, The device listed in the product specification sheets was designed and manufactured for TV application

2, The spike noise causes the mis-operation of circuits. It should be lower than following voltage:

V=±200mV(Over and under shoot voltage)

3, Response time depends on the temperature. (In lower temperature, it becomes longer..)

www.jxlcd.com

4, Brightness depends on the temperature. (In lower temperature, it becomes lower.) And in lower

temperature, response time (required time that brightness is stable after turned on) becomes longer.

5, Be careful for condensation at sudden temperature change. Condensation makes damage to polarizer or

electrical contacted parts. And after fading condensation, smear or spot will occur.

6, When fixed patterns are displayed for a long time, remnant image is likely to occur.

www.braemac.co.uk sales@braemac.co.uk

Tel: 01925 419090 Fax: 01925 419091

7, Module has high frequency circuits. Sufficient suppression to the electromagnetic interference shall be

done by system manufacturers. Grounding and shielding methods may be important to minimize the

interface.

9-3 ELECTROSTATIC DISCHARGE CONTROL

Since a module is composed of electronic circuits, it is not strong to electrostatic discharge. Make certain that

treatment persons are connected to ground through wrist band etc. And don’t touch interface pin directly.

9-4 PRECAUTIONS FOR STRONG LIGHT EXPOSURE

Strong light exposure causes degradation of polarizer and color filter.

9-5 STORAGE

When storing modules as spares for a long time, the following precautions are necessary.

1, Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the

temperature between 5

к

and 35к at normal humidity.

2, The polarizer surface should not come in contact with any other object. It is recommended that they be

stored in the container in which they were shipped.

9-6 HANDLING PRECAUTIONS FOR PROTECTION FILM

1, The protection film is attached to the bezel with a small masking tape. When the protection film is peeled

off, static electricity is generated between the film and polarizer. This should be peeled off slowly and

carefully by people who are electrically grounded and with well ion-blown equipment or in such a condition,

etc.

2, When the module with protection film attached is stored for a long time, sometimes there remains a very

small amount of flue still on the Bezel after the protection film is peeled off.

3, You can remove the glue easily. When the glue remains on the Bezel or its vestige is recognized, please

wipe them off with absorbent cotton waste or other soft material like chamois soaked with normal-hexane.

www.jxlcd.com

www.braemac.co.uk sales@braemac.co.uk

Tel: 01925 419090 Fax: 01925 419091

Appendix EDID:

Item Description Value

Vendor Code

Vendor code

Panel Inch

H.Resolution

V.Resolution

0 : - 1 : AUO

Panel Inch, setting function:

21.6inch= 22 / 26inch= 26

32inch= 32 / 37inch= 37 40inch= 40 / 42inch= 42 46inch= 46 / 52inch= 52

Panel Horizontal resolution information. 16bit : 0x02 = MS Byte, 0x03 = LS Byte

(1) Horizontal resolution = 3840 (2) Horizontal resolution = 1920 (3) Horizontal resolution = 1366

Panel Vertical Resolution information: 16bit : 0x04 = MS Byte, 0x05 = LS Byte

(1) Vertical resolution = 2160 (2) Vertical resolution = 1080 (3) Vertical resolution = 768

1

22

1366

768

V. Frequency

Data format

Part Number

Panel Vertical frequency information.

0: 50Hz / 60Hz 1: 100Hz / 120Hz 2: 200Hz / 240Hz

www.jxlcd.com

Panel LVDS Data format information. 0: 6bit / 1: 8bit 2: 10bit / 3: 12bit 4: 14bit / 5: 16bit

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Panel maker’s version information. @ Example: T260XW05 V0 Item: (

"T","2","6","0","X","W","0","5"," ","V","0"," ? "

0),(1),(2),(3),(4),(5),(6),(7),(8),(9),(10),(11)

T 2 1 6 X W 0 1 V 3

ʳʳʳʳ

ʳʳʳʳ ʳʳʳʳ ʳʳʳʳ ʳʳʳʳ

0

1

Capitalization

www.braemac.co.uk sales@braemac.co.uk

Tel: 01925 419090 Fax: 01925 419091

AU Optronics T216XW01-V3 Product Specification

Specifications and Main Features

Frequently Asked Questions

User Manual