) Preliminary Specification
(
( V ) Final Specification
Product Specification
AU OPTRONICS CORPORATION
M240HW01 V0
Module
Model Name
Customer Date
Approved by
www.jxlcd.com
www.jxlcd.com
24.0” Color TFT-LCD
M240HW01 V0
Approved by Date
Sean Chen
Prepared by
2008/5/20
Note: This Specification is subject to
change without notice.
Frankie Wang
Desktop Display Business Group /
AU Optronics corporation
2008/5/20
AUO Confidential For ACMEPOINT Internal Use Only / 2008/8/26
document version 1.0 1
Product Specification
AU OPTRONICS CORPORATION
Contents
M240HW01 V0
1.0 Handling Precautions .....................................................................................4
2.0 General Description ........................................................................................5
2.1 Display Characteristics....................................................................................................... 5
2.2 Optical Characteristics ....................................................................................................... 6
3.0 Functional Block Diagram ............................................................................ 11
4.0 Absolute Maximum Ratings .........................................................................12
4.1 TFT LCD Module.............................................................................................................. 12
4.2 Backlight Unit ................................................................................................................... 12
4.3 Absolute Ratings of Environment..................................................................................... 12
5.0 Electrical characteristics .............................................................................. 13
5.1 TFT LCD Module.............................................................................................................. 13
5.1.1 Power Specification ................................................................................................... 13
5.1.2 Signal Electrical Characteristics ................................................................................. 14
5.2 Backlight Unit ................................................................................................................... 15
6.0 Signal Characteristic.....................................................................................17
6.1 Pixel Format Image .......................................................................................................... 17
6.2 The input data format ....................................................................................................... 17
6.3 Signal Description ............................................................................................................ 18
6.4 Timing Characteristics...................................................................................................... 19
6.5 Timing diagram ................................................................................................................ 20
6.6 Power ON/OFF Sequence ............................................................................................... 21
www.jxlcd.com
www.jxlcd.com
7.0 Connector & Pin Assignment.......................................................................22
7.1 TFT LCD Module.............................................................................................................. 22
7.1.1 Pin Assignment .......................................................................................................... 22
7.2 Backlight Unit ................................................................................................................... 23
7.2.1 Signal for Lamp connector ......................................................................................... 23
8.0 Reliability Test............................................................................................... 24
9.0 Shipping Label ..............................................................................................25
10.0 Mechanical Characteristics ........................................................................ 26
AUO Confidential For ACMEPOINT Internal Use Only / 2008/8/26
document version 1.0 2
Product Specification
AU OPTRONICS CORPORATION
M240HW01 V0
Record of Revision
Version and Date Page
0.1 2008/01/18 All First Edition for Customer N/A
0.2 2008/03/04 5 Weight : 3300 2860
6 Som e notes and testing
equipments m issing
6 Max. Raising Time, TfR = TBD
Max. Falling Time, TfF = TBD
6 Color / Chromaticity Coordinates
(CIE) : TBD
8 Note 4
12 Logic/LCD Drive Voltage max : 5.5
CCFL Current max : 7.5
13 Inrush Current : TBD Inrush Current : 3.0
Old description New Description Remark
Note 3,5,6 with TOPCON SR-3
added and Note1~9 re-ordered
Max. Raising Time, TfR = 7.4 msec
Max. Falling Time, TfF = 2.6 msec
TfR + TfF = 5 msec (typ.) and algorithm
of Gray to Gray level response time
added in Note 4
Logic/LCD Drive Voltage max : 6.0
CCFL Current max : 8.0
15 CCFL Frequency, CCFL Ignition
15 N/A Note 6 for designing CCFL current
19 Timing Characteristics
25 N/A Note 3 and China RoHS sign added
26 Drawing Change BL label position
27 Drawing Change BL label position
1.0 2008/05/20 15
21
www.jxlcd.com
www.jxlcd.com
Voltage, CCFL Operation Voltage,
CCFL Power Consumption : TBD
added
document version 1.0 3
AUO Confidential For ACMEPOINT Internal Use Only / 2008/8/26
Product Specification
AU OPTRONICS CORPORATION
M240HW01 V0
1.0 Handling Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard
surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth
when handling.
7) Do not open or modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) In case if a Module has to be put back into the packing container slot after once it was taken
out from the container, do not press the center of the CCFL reflector edge. Instead, press at
the far ends of the CCFL Reflector edge softly. Otherwise the TFT Module may be damaged.
10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the
Interface Connector of the TFT Module.
11) After installation of the TFT Module into an enclosure, do not twist nor bend the TFT Module
even momentary. At designing the enclosure, it should be taken into consideration that no
bending/twisting forces are applied to the TFT Module from outside. Otherwise the TFT
Module may be damaged.
12) Cold cathode fluorescent lamp in LCD contains a small amount of mercury. Please follow
local ordinances or regulations for disposal.
13) Small amount of materials having no flammability grade is used in the LCD module. The LCD
module should be supplied by power complied with requirements of Limited Power Source
(IEC60950 or UL1950), or be applied exemption.
14) The LCD module is designed so that the CCFL in it is supplied by Limited Current Circuit
(IEC60950 or UL1950). Do not connect the CCFL in Hazardous Voltage Circuit.
www.jxlcd.com
www.jxlcd.com
AUO Confidential For ACMEPOINT Internal Use Only / 2008/8/26
document version 1.0 4
Product Specification
AU OPTRONICS CORPORATION
2.0 General Description
This specification applies to the 24 inch-wide Color a-Si TFT-LCD Module M240HW01.The
display supports the Full HD - 1920(H) x 1080(V) screen format and 16.7M colors (RGB 6-bits +
Hi-FRC data). All input signals are 2-channel LVDS interface and this module doesn’t contain an
inverter board for backlight.
2.1 Display Characteristics
The following items are characteristics summary on the table under 25℃ condition:
ITEMS Unit SPECIFICATIONS
Screen Diagonal [mm]
Active Area [mm] 531.36 (H) x 298.89 (V)
Pixels H x V 1920(x3) x 1080
Pixel Pitch [um] 276.75 (per one triad) ×276.75
Pixel Arrangement R.G.B. Vertical Stripe
Display Mode TN Mode, Normally White
White Luminance ( Center ) [cd/m2]
Contrast Ratio 1000 (Typ.)
Optical Response Time [msec] 5ms (Typ., on/off)
2ms (Gray to Gray)
Nominal Input Voltage VDD [Volt] +5.0 V
Power Consumption
(VDD line + CCFL line)
Weight [g] 2860 (Typ.)
Physical Size [mm] 556.0 (W) x 323.2 (H) x 16.65 (D) typ
Electrical Interface Dual channel LVDS
Support Color 16.7M colors (RGB 6-bit + Hi_FRC )
Surface Treatment Anti-Glare, 3H
Temperature Range
Operating
Storage (Shipping)
RoHS Compliance RoHS Compliance
www.jxlcd.com
www.jxlcd.com
609.7(24.0”)
2
300 cd/m
[Watt] 35 W (Typ.)
(without inverter, all black pattern)
[oC]
[oC]
0 to +50
-20 to +60
(Typ.)
M240HW01 V0
AUO Confidential For ACMEPOINT Internal Use Only / 2008/8/26
document version 1.0 5
Product Specification
AU OPTRONICS CORPORATION
M240HW01 V0
2.2 Optical Characteristics
The optical characteristics are measured under stable conditions at 25℃:
Item Unit Conditions Min. Typ. Max. Note
Horizontal (Right)
Viewing Angle [degree]
Contrast ratio Normal Direction
Response Time [msec]
Color / Chromaticity
Coordinates (CIE)
Color Coordinates (CIE) White
Central Luminance [cd/m2] 240 300 - 6
Luminance Uniformity
Crosstalk (in 60Hz)
Flicker
www.jxlcd.com
www.jxlcd.com
[%]
[%]
dB
CR = 10 (Left)
Vertical (Up)
CR = 10 (Down)
Raising Time (TrR)
Falling Time (TrF)
Raising + Falling
Gray to Gray
Red x
Red y
Green x
Green y
Blue x
Blue y
White x
White y
150
140
600
-
-
-
-
0.619 0.649 0.679
0.308 0.338 0.368
0.259 0.289 0.319
0.579 0.609 0.639
0.116 0.146 0.176
0.040 0.070 0.100
0.283 0.313 0.343
0.299 0.329 0.359
75 80
170
160
1000 -
3.4 7.4
1.6 2.6
5 10
2 -
-
-
-
-
-
1.5 8
-20
2
3
4
5
7
9
AUO Confidential For ACMEPOINT Internal Use Only / 2008/8/26
document version 1.0 6
Product Specification
TFT-LCD Module
LCD Panel
AU OPTRONICS CORPORATION
Note 1: Measurement method
The LCD module should be stabilized at given temperature for 30 minutes to avoid abrupt
temperature change during measuring (at surface 35). In order to stabilize the luminance, the
measurement should be executed after lighting Backlight for 30 minutes in a stable, windless and
dark room.
Photo detector
M240HW01 V0
Measured distance
Note 2: Definition of viewing angle measured by ELDIM (EZContrast 88)
Viewing angle is the measurement of contrast ratio ≧10, at the screen center, over a 180°
horizontal and 180° vertical range (off-normal viewing angles). The 180° viewing angle range is
broken down as follows; 90° (θ) horizontal left and right and 90° (Φ) vertical, high (up) and low
(down). The measurement direction is typically perpendicular to the display surface with the
screen rotated about its center to develop the desired measurement viewing angle.
www.jxlcd.com
www.jxlcd.com
Center of the screen
AUO Confidential For ACMEPOINT Internal Use Only / 2008/8/26
document version 1.0 7
Product Specification
F
R
F
R
1 Frame
AU OPTRONICS CORPORATION
M240HW01 V0
Note 3: Contrast ratio is measured by TOPCON SR-3
Note 4: Definition of Response time measured by Westar TRD-100A
The output signals of photo detector are measured when the input signals are changed from “Full
Black” to “Full White” (rising time, TrR), and from “Full White” to “Full Black” (falling time, TfF),
respectively. The response time is interval between the 10% and 90% (1 frame at 60 Hz) of
amplitudes.
Optical
Optical
response
response
100
100
90
10
10
%
%
W hite
0
0
Tr
Tr
Black
1 Frame
Black
Tr
Tr
W hite
TrR + TfF = 5 msec (typ.).
Algorithm:┃Gray Level A – Gray Level B┃32, then the average gray to gray response time is 2
ms.
www.jxlcd.com
www.jxlcd.com
Note 5: Color chromaticity and coordinates (CIE) is measured by TOPCON SR-3
Note 6: Central luminance is measured by TOPCON SR-3
Note 7: Luminance uniformity of these 9 points is defined as below and measured by
TOPCON SR-3
AUO Confidential For ACMEPOINT Internal Use Only / 2008/8/26
document version 1.0 8
Product Specification
AU OPTRONICS CORPORATION
M240HW01 V0
Uniformity =
Note 8: Crosstalk is defined as below and measured by TOPCON SR-3
CT = | YB – YA | / YA × 100 (%)
Where
YA = Luminance of measured location without gray level 0 pattern (cd/m2)
YB = Luminance of measured location with gray level 0 pattern (cd/m2)
www.jxlcd.com
www.jxlcd.com
9)-(1 points 9in LuminanceMinimum
9)-(1 Points 9in LuminanceMaximum
Note 9: Test Patern: Subchecker Pattern measured by TOPCON SR-3
R G B R G B
Gray Level = L127
R G B R G B
AUO Confidential For ACMEPOINT Internal Use Only / 2008/8/26
R G B R G B
document version 1.0 9
Gray Level = L0
Loading...