Product Specification
) Preliminary Specification
( V
( ) Final Specification
Module 19.0” WXGA Color TFT-LCD
AU OPTRONICS CORPORATION
M190PP01 V0
Model Name M190PP01 V0
Customer Date
Approved by
www.jxlcd.com
www.jxlcd.com
Prepared by Date
Flossie Chuang
Approved by
Sep. 1, 2008
Note: This Specification is subject to
change without notice.
Sean Chen
Desktop Display Business Group /
AU Optronics corporation
Sep. 1, 2008
AUO Confidential For PROMATE Internal Use Only / 2009/12/8
document version 0.2 1/27
Product Specification
1.0 Handling Precautions ................................................................................................................4
2.0 General Description ...................................................................................................................5
2.1 Display Characteristics..............................................................................................................5
2.2 Optical Characteristics ..............................................................................................................6
3.0 Functional Block Diagram...................................................................................................... 10
4.0 Absolute Maximum Ratings ................................................................................................... 11
4.1 TFT LCD Module .....................................................................................................................11
4.2 Backlight Unit...........................................................................................................................11
4.3 Absolute Ratings of Environment............................................................................................11
5.0 Electrical Characteristics ....................................................................................................... 12
5.1 TFT LCD Module .................................................................................................................... 12
AU OPTRONICS CORPORATION
Contents
M190PP01 V0
5.1.1 Power Specification............................................................................................................. 12
5.1.2 Signal Electrical Characteristics.......................................................................................... 12
5.2 Backlight Unit ........................................................................................................................ 13
6.0 Signal Characteristic............................................................................................................... 14
6.1 Pixel Format Image ................................................................................................................ 14
6.2 Signal Description................................................................................................................... 15
www.jxlcd.com
6.3 Timing Characteristics ............................................................................................................ 17
6.3.1 Safe mode: 640×480@60Hz; .......................................................................................... 17
6.3.2 Native mode: .................................................................................................................... 18
(1) 1440×900@60Hz – Reduce Blanking................................................................................. 18
(2) 800×600@60Hz................................................................................................................... 19
6.4 EEPROM Memory Placement – 4K ....................................................................................... 20
6.5 Power ON/OFF Sequence ..................................................................................................... 21
7.0 Mode States ............................................................................................................................. 22
7.1 Kick-Off Condition................................................................................................................... 22
7.2 BIST Mode .............................................................................................................................. 22
7.3 Low Power Mode.................................................................................................................... 23
www.jxlcd.com
7.4 Error Mode (Failure Detection Mode) .................................................................................... 23
8.0 Connector & Pin Assignment ................................................................................................ 24
8.1 TFT LCD Module .................................................................................................................... 24
8.1.1 Pin Assignment ................................................................................................................ 24
8.2 Backlight Unit.......................................................................................................................... 25
8.2.1 Signal for Lamp connector............................................................................................... 25
AUO Confidential For PROMATE Internal Use Only / 2009/12/8
9.0 Reliability Test ......................................................................................................................... 26
10.0 Shipping Label ....................................................................................................................... 27
11.0 Mechanical Characteristics ................................................................................................. 28
document version 0.2 2/27
Product Specification
AU OPTRONICS CORPORATION
M190PP01 V0
Record of Revision
Version and Date Page
0.1 2008/02/13 All First Edition for Customer -
Old description New Description Remark
0.2 2008/09/01 12 5.1.1 Power Specification
IDD: 0.9A(typ); PDD: 4.5W(typ)
13 5.2 Backlight Unit
FCFL: 50 [KHz]
VCFL: 771 [Volt]rms
21 6.5 Power On/Off Sequence Re-define the signal definitions and
20 6.4 EEPROM Memory Placement –
16K
www.jxlcd.com
www.jxlcd.com
5.1.1 Power Specification
IDD: 1.0A(typ); PDD: 5.0W(typ)
5.2 Backlight Unit
FCFL: 55 [KHz]
VCFL: 718 [Volt]rms
1. Change from 16K to 4K
2. Update the memory placement
values
Modify
Modify
Modify
Modify
AUO Confidential For PROMATE Internal Use Only / 2009/12/8
document version 0.2 3/27
Product Specification
AU OPTRONICS CORPORATION
M190PP01 V0
1.0 Handling Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or
spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard
surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human
earth when handling.
7) Do not open or modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) In case if a Module has to be put back into the packing container slot after once it was
taken out from the container, do not press the center of the CCFL reflector edge.
Instead, press at the far ends of the CCFL Reflector edge softly. Otherwise the TFT
Module may be damaged.
10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor
tilt the Interface Connector of the TFT Module.
www.jxlcd.com
11) After installation of the TFT Module into an enclosure, do not twist nor bend the TFT
Module even momentary. At designing the enclosure, it should be taken into
consideration that no bending/twisting forces are applied to the TFT Module from
outside. Otherwise the TFT Module may be damaged.
12) Cold cathode fluorescent lamp in LCD contains a small amount of mercury. Please follow
local ordinances or regulations for disposal.
13) Small amount of materials having no flammability grade is used in the LCD module. The LCD
module should be supplied by power complied with requirements of Limited Power Source
(IEC60950 or UL1950), or be applied exemption.
14) The LCD module is designed so that the CCFL in it is supplied by Limited Current Circuit
(IEC60950 or UL1950). Do not connect the CCFL in Hazardous Voltage Circuit.
www.jxlcd.com
AUO Confidential For PROMATE Internal Use Only / 2009/12/8
document version 0.2 4/27
Product Specification
2.0 General Description
This specification applies to the 19 inch-wide Color a-Si TFT-LCD Module M190PP01 V0.
The display supports the WXGA (1440(H) x 900(V)) screen format and 16.7M colors (RGB
6-bits + Hi-FRC data).
All input signals are 1 Lane Displayport interface compatible.
This module doesn’t contain an inverter board for backlight.
2.1 Display Characteristics
AU OPTRONICS CORPORATION
M190PP01 V0
The following items are characteristics summary on the table under 25 ℃ condition:
ITEMS Unit SPECIFICATIONS
Screen Diagonal [mm] 482.6 (19.0”Wide)
Active Area [mm] 408.24 (H) x 255.15(V)
Pixels H x V 1440(x3) x 900
Pixel Pitch [mm] 0.2835(per one triad) x 0.2835
Pixel Arrangement R.G.B. Vertical Stripe
Display Mode TN Mode, Normally White
White Luminance ( Center ) [cd/m2]
Contrast Ratio 1000 (Typ.)
Optical Response Time [msec] 5ms (Typ., on/off)
Nominal Input Voltage VDD [Volt] +5.0 V
Power Consumption
(VDD line + CCFL line)
Weight [Grams] 2120 (Typ.)
Physical Size [mm] 428.0(W) x 278.0(H) x 18.5(D) (Typ)
Electrical Interface 1 Lane Displayport (HDCP v1.3 ; EDID1.4)
Support Color 16.7M colors (RGB 6-bit + Hi_FRC )
Surface Treatment Anti-Glare, 3H
Temperature Range
Operating
Storage (Shipping)
RoHS Compliance RoHS Compliance
www.jxlcd.com
www.jxlcd.com
[Watt] 24 W (Typ.)
[oC]
[oC]
300 cd/m
0 to +50
-20 to +60
2 @ 6.5mA
(Typ)
AUO Confidential For PROMATE Internal Use Only / 2009/12/8
document version 0.2 5/27
2.2 Optical Characteristics
Product Specification
AU OPTRONICS CORPORATION
M190PP01 V0
The optical characteristics are measured under stable conditions at 25℃.
Item Unit Conditions Min. Typ. Max. Note
[degree]
Viewing Angle
Contrast ratio Normal Direction 600 1000 -
Response Time
Color / Chromaticity
Coordinates (CIE)
[degree]
[degree]
[degree]
[msec]
[msec]
[msec]
Horizontal (Right)
CR = 10 (Left)
Vertical (Up)
CR = 10 (Down)
Raising Time - 3.4 7.4
Falling Time - 1.6 2.6
Raising + Falling - 5 10
Red x
Red y
Green x
Green y
150 170
140 160
0.620 0.650 0.680
0.310 0.340 0.370
0.260 0.290 0.320
0.580 0.610 0.640
-
1,3
-
-
1
1,2
1
www.jxlcd.com
www.jxlcd.com
Color Coordinates (CIE)
White
Central Luminance (IL=6mA) [cd/m2]
Luminance Uniformity
Crosstalk (At 60Hz)
Flicker
[%] 75 80 - 1,4
[%] 1.5 1,5
dB -20 1,6
Blue x
Blue y
White x
White y
240 300 - 1
0.120 0.150 0.180
0.040 0.070 0.100
0.283 0.313 0.343
0.299 0.329 0.359
1
AUO Confidential For PROMATE Internal Use Only / 2009/12/8
document version 0.2 6/27
Product Specification
TFT-LCD Module
LCD Panel
Note 1: Measurement method
The LCD module should be stabilized at given temperature for 30 minutes to avoid abrupt
temperature change during measuring. In order to stabilize the luminance, the measurement
should be executed after lighting Backlight for 30 minutes in a stable, windless and dark room.
AU OPTRONICS CORPORATION
Photo detector
M190PP01 V0
Measurement
www.jxlcd.com
Note 2: Definition of Response time measured by Westar TRD-100A
The output signals of photodetector are measured when the input signals are changed from
“Black” to “White” (rising time), and from “White” to “Black ”(falling time), respectively. The
response time is interval between the 10% and 90% of amplitudes.
www.jxlcd.com
Center of the screen
Distance
document version 0.2 7/27
AUO Confidential For PROMATE Internal Use Only / 2009/12/8
Product Specification
M190PP01 V0
AU OPTRONICS CORPORATION
Note 3: Definition of viewing angle: measured by TOPCON SR-3
Viewing angle is the measurement of contras
ra
o
tth
a
escreencen
,
t
er
o
v
,
180°
era
t
ti
10
horizontal and 180° vertical range (off-normal viewing angles). The 180° viewing angle range is
broken down as follows; 90° (θ) horizontal left and right and 90° (Φ) vertical, high (up) and low
(down). The measurement direction is typically perpendicular to the display surface with the
screen rotated about its center to develop the desired measurement viewing angle.
Note 4: Luminance uniformity of these 9 points is defined as below measured by TOPCON
www.jxlcd.com
www.jxlcd.com
SR-3
AUO Confidential For PROMATE Internal Use Only / 2009/12/8
Uniformity =
9)-(1 points 9in LuminanceMinimum
9)-(1 Points 9in LuminanceMaximum
document version 0.2 8/27
Product Specification
Level
DC
Note 5: Crosstalk is defined as below : measured by TOPCON SR-3
CT = | YB – YA | / YA × 100 (%)
Where
YA = Luminance of measured location without gray level 0 pattern (cd/m2)
YB = Luminance of measured location with gray level 0 pattern (cd/m2)
AU OPTRONICS CORPORATION
M190PP01 V0
Note 6: Test Paterm: Subchecker Pattern measured by TOPCON SR-3
R G B R G B
www.jxlcd.com
www.jxlcd.com
R G B R G B
R G B R G B
Method: Record dBV & DC value with (WESTAR)TRD-100
Amplitude
DC
Gray Level = L127
Gray Level = L0
log20(dB)Flicker =
AC
Time
Hz) 30Level(at AC
AUO Confidential For PROMATE Internal Use Only / 2009/12/8
document version 0.2 9/27
Loading...