AU Optronics M190EN02-V2 Product Specification

Version:

www.DataSheet.co.kr

Datasheet pdf - http://www.DataSheet4U.net/

Spec. No.: DDPM-EN02-0.2

2 Total pages: 24 Date: 2003-August-29

AU OPTRONICS CORPORATION

Product Specifications

19.0” SXGA Color TFT-LCD Module

Model Name: M190EN02

V.2

www.jxlcd.com

Approved by Prepared by

DDBU Marketing Division / AU Optronics Croporation

Customer Checked & Approved by

1/24

) Preliminary Specifications

www.DataSheet.co.kr

Datasheet pdf - http://www.DataSheet4U.net/

Product Specifications

19.0” SXGA Color TFT-LCD Module Model Name: M190EN02

V.2

(u

( ) Final Specifications

www.jxlcd.com

Note: This Specification is subject to change without notice.

2/24

i Contents

www.DataSheet.co.kr

Datasheet pdf - http://www.DataSheet4U.net/

ii Record of Revision

1.0 Handling Precautions

2.0 General Description

2.1 Display Characteristics

2.2 Functional Block Diagram

2.3 Optical Characteristics

2.4 Pixel format image

3.0 Electrical characteristics

3.1 Absolute Maximum Ratings

3.2 Connectors

3.3 Signal Pin

3.4 Signal Description

3.5 Signal Electrical Characteristics

3.6 Interface Timing

3.6.1 Timing Characteristics

3.6.2 Timing Definition

3.7 Power Consumption

3.8 Power ON/OFF Sequence

4.0 Backlight Characteristics

4.1 Signal for Lamp connector

4.2 Parameter guide line for CCFL Inverter

5.0 Vibration, shock and drop

5.1 Vibration and shock

5.2 Drop test

6.0 Environment

6.1 Temperature and humidity

6.1.1 Operating conditions

6.1.2 Shipping conditions

6.2 Atmospheric pressure

6.3 Thermal shock

www.jxlcd.com

7.0 Reliability

7.1 Failure criteria

7.2 Failure rate

7.2.1 Usage

7.2.2 Components de-rating

7.3 CCFL life

7.4 ON/OFF cycle

8.0 Safety

8.1 Sharp edge requirement

8.2 Material

8.2.1 Toxicity

8.2.2 Flammability

8.3 Capacitors

8.4 Hazardous voltage

9.0 Other requirements

9.1 Smoke free design

9.2 National test lab requirement

10.0 Mechanical Characteristics

3/24

www.DataSheet.co.kr

Datasheet pdf - http://www.DataSheet4U.net/

ii Record of Revision

Version and Date Page Old description New Description Remark

0.1 2003/07/01 All First Edition for Customer All

0.2 2003/8/29 5,7 Contrast Ratio : 600:1 (typ) Contrast Ratio : 700:1 (typ) Update

1.0 Handling Precautions

1) Since front polarizer is easily damaged, pay attention not to scratch it.

2) Be sure to turn off power supply when inserting or disconnecting from input connector.

3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.

4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.

5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.

6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth when handling.

7) Do not open nor modify the Module Assembly.

8) Do not press the reflector sheet at the back of the module to any directions.

9) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the Interface Connector of the TFT-LCD module.

10) After installation of the TFT-LCD module into an enclosure (LCD monitor housing, for example), do not twist nor bend the TFT -LCD module even momentary. At designing the enclosure, it should be taken into consideration that no bending/twisting forces are applied to the TFT -LCD module from outside. Otherwise the TFT -LCD module may be damaged.

www.jxlcd.com

4/24

www.DataSheet.co.kr

Datasheet pdf - http://www.DataSheet4U.net/

2.0 General Description

This specification applies to the 19.0 inch Color TFT-LCD Module M190EN02. The display supports the SXGA (1280(H) x 1024(V)) screen format and 16.7M colors (RGB 8-bits data).

All input signals are 2 Channel LVDS interface compatible. This module does not contain an inverter card for backlight.

2.1 Display Characteristics

The following items are characteristics summary on the table under 25 ℃ condition:

ITEMS Unit SPECIFICATIONS

Screen Diagonal [mm] 480(19") Active Area [mm] 376.32 (H) x 301.056 (V) Pixels H x V 1280(x3) x 1024 Pixel Pitch [mm] 0.294 (per one triad) x 0.294 Pixel Arrangement R.G.B. Vertical Stripe Display Mode Normally Black White Luminance ( Center ) [cd/m2] Contrast Ratio 700 : 1 (Typ) Optical Response Time [msec] 25 (Typ) Nominal Input Voltage VDD [Volt] +5.0 V Power Consumption (VDD line + CCFL line) Weight [Grams] 2700 (Typ) Physical Size [mm] 404.2(W) x 330(H) x 20(D) (Typ) Electrical Interface Even/Odd R/G/B data, 3 sync signal,

Support Color 16.7M colors (RGB 8-bit data ) Temperature Range Operating Storage (Shipping)

www.jxlcd.com

[Watt] 40W (typ.) (w/o Inverter, All white pattern)

[oC] [oC]

250 cd/m

Clock

0 to +50

-20 to +60

2 @7mA

(Typ)

5/24

D1

www.DataSheet.co.kr

Datasheet pdf - http://www.DataSheet4U.net/

2.2 Functional Block Diagram

The following diagram shows the functional block of the 19 inches Color TFT-LCD Module:

LVDS

+5V

Connector

Receiver

DC/DC

Converter

www.jxlcd.com

I/F + X-PCB

JAE FI-XB30SL-HF10 JST BHSR-02VS-1 Mating Type: Mating Type: SM02(8.0)B-BHSS JAE FI-X30HL-T ( Locked Type ) JAE FI-X30S-H ( Unlocked Type )

LVDS

AU ASIC

Gamma

Correction

Timing

Controller

DC POWER

G1

G1024

TFT-LCD

1280*(3)*1024

Pixels

Inverter

D3840 4 CCFL

6/24

www.DataSheet.co.kr

Datasheet pdf - http://www.DataSheet4U.net/

2.3 Optical Characteristics

The optical characteristics are measured under stable conditions at 25℃ (Room Temperature):

Item Unit Conditions Min. Typ. Max.

Viewing Angle

Contrast ratio Normal Direction 400 700 Response Time (Note 1)

Color / Chromaticity Coordinates (CIE)

White Luminance at CCFL 7.0mA (central point) Luminance Uniformity (Note 2) [%] 75 80 Crosstalk (in75Hz) (Note 3) [%] 1.5

[degree] [degree]

[msec] Raising Time - 15 25 [msec] Falling Time - 10 15

[msec] Raising + Falling - 25 40

[cd/m2] 200 250 -

Horizontal (Right) CR = 10 (Left)

Vertical (Up) CR = 10 (Down)

75

Red x 0.604 0.634 0.664

Red y 0.324 0.354 0.384 Green x 0.278 0.308 0.338 Green y 0.576 0.606 0.636

Blue x 0.108 0.138 0.168

Blue y 0.057 0.087 0.117 White x 0.28 0.31 0.34 Color Coordinates (CIE) White White y 0.30 0.33 0.36

85 85

Equipment Pattern Generator, Power Supply, Digital Voltmeter, Luminance meter (PR 880, BM-5A ,

BM 7 , & EZContrast* )

Aperture 1

Test Point Center (ISO point 22)

Environment < 1 lux

www.jxlcd.com

∘

with 100cm VD or 2∘with 50cm viewing distance

-

LCD Module

PR-880 /

BM5A /

BM7

measuring distance

Module Driving Equipment

‘*’ EZ Contrast is different measurement tool with very close viewing distance.

7/24

Response

100%

90%

10%

0%

Tf Tr

www.DataSheet.co.kr

Datasheet pdf - http://www.DataSheet4U.net/

Note 1: Definition of Response time:

The output signals of photodetector are measured when the input signals are changed from “ Black” to “ White” (raising time), and from “White” to “ Black” (falling time), respectively. The response time is interval between the 10% and 90% of amplitudes. Refer to figure as below.

Optical

Note 2: Brightness uniformity of these 9 points is defined as below:

Minimum Luminance in 9 Points (1-9) Uniformity = ———————————————————

Maximum Luminance in 9 Points (1-9)

www.jxlcd.com

90 %

50 %

10 %

50 %

90 %

8/24

R G B R G B R G B R G B R G B R G B R G B R G B

1 2

1

279 1

280 1st Line

1024th Line

A B

www.DataSheet.co.kr

Datasheet pdf - http://www.DataSheet4U.net/

Note 3: Crosstalk is defined as below :

Unit: percentage of dimension of display area l LA-LA’ l / LA x 100%= 1.5% max., LA and LB are brightness at location A and B

l LB-LB’ l / LB x 100%= 1.5% max., LA’ and LB’ are brightness at location A’ and B’

184 gray level 184 gray level

1/2

1/6

1/2

2/3

1/2

A

1/6

1/3

B’

0 gray level

1/6 1/3 1/2

2/3

2.4 Pixel format image

Following figure shows the relationship of the input signals and LCD pixel format.

www.jxlcd.com

9/24

Temperature

o

C

-20 0 60 50

5

100

0

80 60

40

20

www.DataSheet.co.kr

Datasheet pdf - http://www.DataSheet4U.net/

3.0 Electrical characteristics

3.1 Absolute Maximum Ratings

Absolute maximum ratings of the module is as following:

Item Symbol Min Max Unit Conditions

Logic/LCD Drive Voltage VIN -0.3 +5.5 [Volt] Select LVDS data order SELLVDS CCFL Inrush current ICFLL - 38 [mA] Note 1

NC NC [Volt]

CCFL Current ICFL - 7.5 [mA] rms Operating Temperature TOP 0 +50 [ Operating Humidity HOP 8 95 [%RH] Note 2 Storage Temperature TST -20 +60 [ Storage Humidity HST 8 95 [%RH] Note 2

Note 1 : Duration=50 msec. Note 2 : Maximum Wet-Bulb should be 39℃ and No condensation.

o

C] Note 2

o

C] Note 2

Relative Humidity %

www.jxlcd.com

95

www.jxlcd.com

Twb=39℃

T=40℃,H=95%

T=50℃,H=55%

Storage range

Operation range

T=60℃,H=39%

T=65℃,H=29%

Storage

10/24

FI-X30S

-H ( Unlocked Type )

www.DataSheet.co.kr

Datasheet pdf - http://www.DataSheet4U.net/

3.2 Connectors

Physical interface is described as for the connector on module. These connectors are capable of accommodating the following signals and will be following components.

Connector Name / Designation

Interface Connector / Interface card

Manufacturer Type Part Number Mating Housing Part Number

Connector Name / Designation Manufacturer

Type Part Number Mating Type Part Number

www.jxlcd.com

3.3 Signal Pin

Pin# Signal Name Pin# Signal Name

1 RxO0- 2 RxO0+ 3 RxO1- 4 RxO1+ 5 RxO2- 6 RxO2+ 7 GND 8 RxOC-

9 RxOC+ 10 RxO311 RxO3+ 12 RxE013 RxE0+ 14 GND 15 RxE1- 16 RxE1+ 17 GND 18 RxE219 RxE2+ 20 RxEC21 RxEC+ 22 RxE323 RxE3+ 24 GND 25 NC 26 NC 27 NC 28 Power 29 Power 30 Power

JAE or compatible FI-XB30SL-HF10 FI-X30HL-T ( Locked Type )

Lamp Connector / Backlight lamp

JST

BHSR-02VS-1 SM02(8.0)B-BHSS

11/24

www.DataSheet.co.kr

Datasheet pdf - http://www.DataSheet4U.net/

3.4 Signal Description

The module using a pair of LVDS receiver SN75LVDS82(Texas Instruments) or compatible. LVDS is a differential signal technology for LCD interface and high speed data transfer device. Transmitter shall be SN75LVDS83(negative edge sampling) or compatible. The first LVDS port(RxOxxx) transmits odd pixels while the second LVDS port(RxExxx) transmits even pixels.

PIN # SIGNAL NAME DESCRIPTION 1 RxO0- Negative LVDS differential data input (Odd data) 2 RxO0+ Positive LVDS differential data input (Odd data) 3 RxO1- Negative LVDS differential data input (Odd data) 4 RxO1+ 5 RxO2- Negative LVDS differential data input (Odd data, H-Sync,V-Sync,DSPTMG)

6 RxO2+ Positive LVDS differential data input (Odd data, H-Sync,V-Sync,DSPTMG) 7 GND Power Ground 8 RxOC- Negative LVDS differential clock input (Odd clock)

9 RxOC+ Positive LVDS differential clock input (Odd clock) 10 RxO3- Negative LVDS differential data input (Odd data)

11 RxO3+ Positive LVDS differential data input (Odd data) 12 RxE0- Negative LVDS differential data input (Even clock) 13 RxE0+ Positive LVDS differential data input (Even data) 14 GND Power Ground 15 RxE1- Positive LVDS differential data input (Even data) 16 RxE1+ Negative LVDS differential data input (Even data) 17 GND Power Ground 18 RxE2- Negative LVDS differential data input (Even data) 19 RxE2+ Positive LVDS differential data input (Even data) 20 RxEC- Negative LVDS differential clock input (Even clock) 21 RxEC+ Positive LVDS differential clock input (Even clock) 22 RxE3- Negative LVDS differential data input (Even data) 23 RxE3+ Positive LVDS differential data input (Even data) 24 GND Power Ground 25 NC 26 NC 27 NC 28 POWER Power 29 POWER Power 30 POWER Power

Note: Input signals of odd and even clock shall be the same timing.

www.jxlcd.com

Positive LVDS differential data input (Odd data)

LVDS DATA Name DSP Display Timing: When the signal is high, the pixel data shall be valid to be displayed V-S Vertical Sync: Both Positive and Negative polarity are acceptable H-S Horizontal Sync: Both Positive and Negative polarity are acceptable

Description

12/24

www.DataSheet.co.kr

Datasheet pdf - http://www.DataSheet4U.net/

TI LVDS X’mitter

SN75LVDS83

Module LVDS signal

(interface connector pin7)

Signal Name Low(open)

D0 Red0 D1 Red1 D2 Red2 D3 Red3 D4 Red4 D5 Red7 D6 Red5 D7 Green0 D8 Green1

D9 Green2 D10 Green6 D11 Green7 D12 Green3 D13 Green4 D14 Green5 D15 Blue0 D16 Blue6 D17 Blue7 D18 Blue1 D19 Blue2 D20 Blue3 D21 Blue4

www.jxlcd.com

D22 Blue5 D23 NA D24 H Sync D25 V Sync D26 Display Timing D27 Red6

13/24

www.DataSheet.co.kr

Datasheet pdf - http://www.DataSheet4U.net/

RCLKP1

RAP1

RBP1 RCP1

RDP1

RCLKP2

RAP2

RBP2 RCP2

RDP2

www.jxlcd.com

Note: R/G/B data 7:MSB, R/G/B data 0:LSB

G0(0)R5(R3)R4(R2)R3(R1)R2(R0) R1(0)R0(0)

B1(0)B0(0)G5(G3)G4(G2)G3(G1) G2(G0)G1(0)

DEVSHS RSV

G0(0)R5(R3)R4(R2)R3(R1)R2(R0) R1(0)R0(0)

B1(0)B0(0)G5(G3)G4(G2)G3(G1) G2(G0)G1(0)

RSV

B7(B5)B6(B4)G7(G5)G6(G4) R7(R5)R6(R4)

O = “First Pixel Data”

E = “Second Pixel Data”

B5(B3)B4(B2) B3(B1)B2(B0)

14/24

www.DataSheet.co.kr

Datasheet pdf - http://www.DataSheet4U.net/

3.5 Signal Electrical Characteristics

Input signals shall be low or Hi-Z state when Vin is off It is recommended to refer the specifications of SN75LVDS82DGG (Texas Instruments) in detail.

Each signal characteristics are as follows;

Parameter Condition Min Max Unit

Vth

Vtl

Differential InputHigh Voltage(Vcm=+1.2V)

Differential Input Low Voltage(Vcm=+1.2V)

-100

100

[mV]

3.6 Interface Timings

Basically, interface timings described here is not actual input timing of LCD module but output timing of SN75LVDS82DGG (Texas Instruments) or equivalent.

3.6.1 Timing Characteristics

Signal Item Symbol MIN TYP MAX Unit DTCLK Freq. Fdck - 54 67.5 MHz DTCLK Cycle Tck 14.8 18.5 ns +V-Sync Frame Rate 1/Tv 56.25 60 77 Hz +V-Sync Cycle Tv 13 16.67 17.78 ms +V-Sync Cycle Tv 1035 1066 2047 lines +V-Sync Active level Tva 3 3 lines +V-Sync V-back porch Tvb 7 38 63 lines +V-Sync V-front porch Tvf 1 1 lines +DSPTMG V-Line m 1024 lines +H-Sync Scan rate 1/Th 64 KHz +H-Sync Cycle Th 678 844 1005 Tck +H-Sync Active level Tha(*1) 4 56 Tck +H-Sync Back porch Thb(*1) 30 124 355 Tck +H-Sync Front porch Thf 4 24 Tck +DSPTMG Display Pixels n 640 Tck

Note: Typical value refer to VESA STANDARD, (*1) Tha+Thb should be less than 1024 Tck.

www.jxlcd.com

15/24

112dot

248dot

48dot

1H

38H

3H

DSPTMG

www.DataSheet.co.kr

Datasheet pdf - http://www.DataSheet4U.net/

3.6.2 Timing Definition

H-Sync

DSPTMG

V-Sync

1688dot

1280dot

www.jxlcd.com

3.7 Power Consumption

Input power specifications are as follows;

Symbol Parameter Min Typ Max Units

VDD Logic/LCD Drive

Voltage IDD VDD current IIDD Inrush VDD current PDD VDD Power VDDrp Allowable

Logic/LCD Drive

Ripple Voltage VDDns Allowable

Logic/LCD Drive

Ripple Noise

4.5 5 5.5 [Volt]

1100 1300 [mA]

7 [A] t < 80us

8 [Watt] Vin=5V, All White Pattern

100 [mV]

Condition

p-p

16/24

10%

90%

1sec

On

www.DataSheet.co.kr

Datasheet pdf - http://www.DataSheet4U.net/

3.8 Power ON/OFF Sequence

Vin power and lamp on/off sequence is as follows. Interface signals are also shown in the chart. Signals from any system shall be Hi-Z state or low level when Vin is off.

min.

Vin

0 V

15ms max.

Signal

0 V

Lamp

0 V

www.jxlcd.com

10%

4.0 Backlight Characteristics

4.1 Signal for Lamp connector

Pin #

1

2

Signal Name

Lamp High Voltage

Lamp Low Voltage

10%

0 min. 0 min.

10%

0 min.

250ms

17/24

rms

www.DataSheet.co.kr

Datasheet pdf - http://www.DataSheet4U.net/

4.2 Parameter guide line for CFL Inverter

Symbol Parameter Min Typ Max

Units Condition

(L255) White Luminance 200 250 - [cd/m2 ] ISCFL CCFL standard current 6.5 7.0 7.5 [mA] IRCFL CCFL operation range 3.0 7.0 7.5 [mA]

rms

fCFL CCFL Frequency 40 50 60 [KHz] (Ta=25oC)

ViCFL (0oC) ViCFL (25oC) VCFL CCFL Discharge Voltage

PCFL CCFL Power consumption 17.16 20.16 23.4 [Watt] (Ta=25oC)

CCFL Ignition Voltage 1800 [Volt]

rms

CCFL Ignition Voltage 1500 [Volt]

rms

660

(Reference)

720 780 [Volt]

rms

(Ta=25oC) (Ta=25oC) (Ta=25oC)

Note 1 (Ta=0oC)

Note 2 (Ta=25oC) Note 2 (Ta=25oC) Note 3

Note 3

Note 1: CCFL Frequency should be carefully determined to avoid interference between inverter and TFT LCD Note 2: CCFL inverter should be able to give out a power that has a generating capacity of over 2000 voltage. Lamp units need 2000 voltage minimum for ignition Note 3: Calculator value for reference (ICFL×VCFL=PCFL) Note 4: Lamp soldering method is required to use “Hook Soldering”.

www.jxlcd.com

18/24

www.DataSheet.co.kr

Datasheet pdf - http://www.DataSheet4U.net/

5.0 Vibration, Shock, and Drop

5.1 Vibration & Shock

Frequency: 10 - 200Hz Sweep: 30 Minutes each Axis (X, Y, Z) Acceleration: 1.5G(10~200Hz P- P) Test method:

Acceleration (G)

Frequency (Hz)

Active time(min)

5.2 Shock Test Spec:

Acceleration (G) –a Active time -b Wave form Times

Direction: ±X , ±Y, ±Z

5.3 Drop test

www.jxlcd.com

1.5

10~200~10

30

50 20

half-sin

1

Package test: The drop height is 60 cm.

6.0 Environment

The display module will meet the provision of this specification during operating condition or after storage or shipment condition specified below. Operation at 10% beyond the specified range will not cause physical damage to the unit.

6.1 Temperature and Humidity

6.1.1 Operating Conditions

The display module operates error free, when operated under the following conditions; Temperature 0 0C to 50 0C Relative Humidity 8% to 95% Wet Bulb Temperature 39.0 0C

19/24

www.DataSheet.co.kr

Datasheet pdf - http://www.DataSheet4U.net/

6.1.2 Shipping Conditions

The display module operates error free, after the following conditions; Temperature -20 0C to 60 0C Relative Humidity 8% to 95% Wet Bulb Temperature 39.0 0C

6.2 Atmospheric Pressure

The display assembly is capable of being operated without affecting its operations over the pressure range as following specified;

Pressure Note

Maximum Pressure 1040hPa 0m = sea level

Minimum Pressure 674hPa 3048m = 10.000 feet

Note : Non-operation attitude limit of this display module = 30,000 feet. = 9145 m.

6.3 Thermal Shock

The display module will not sustain damage after being subjected to 100 cycles of rapid temperature change. A cycle of rapid temperature change consists of varying the temperature from -200C to 600C, and back again.

Thermal shock cycle -20 0C for 30min 60 0C for 30min

Power is not applied during the test. After temperature cycling, the unit is placed in normal room ambient for at least 4 hours before powering on.

www.jxlcd.com

7.0 Reliability

This display module and the packaging of that will comply following standards.

7.1 Failure Criteria

The display assembly will be considered as failing unit when it no longer meets any of the requirements stated in this specification. Only as for maximum white luminance, following criteria is applicable.

Note : Maximum white Luminance shall be 125 cd/m2or more.

7.2 Failure Rate

The average failure rate of the display module (from first power-on cycle till 1,000 hours later) will not exceed 1.0%. The average failure rate of the display module from 1,000 hours until 16,000 hours will not exceed 0.7% per 1000 hours.

20/24

www.DataSheet.co.kr

Datasheet pdf - http://www.DataSheet4U.net/

7.2.1 Usage

The assumed usage for the above criteria is:

220 power-on hours per month 500 power on/off cycles per month Maximum brightness setting Operation to be within office environment (250C typical)

7.2.2 Component De-rating

All the components used in this device will be checked the load condition to meet the failure rate criteria.

7.3 CCFL Life

The assumed CCFL Life will be longer than 30,000 hours, typical value is 40,000 hours under stable condition at 25 ± 5oC; Standard current at 7.0 ± 0.5mA. Definition of life: brightness becomes 50% or less than the minimum luminance value of CCFL.

7.4 ON/OFF Cycle

The display module will be capable of being operated over the following ON/OFF Cycles.

ON/OFF Value Cycles

+Vin and CCFL power 30,000 10 seconds on / 10 seconds off

8.0 Safety

8.1 Sharp Edge Requirements

There will be no sharp edges or comers on the display assembly that could cause injury.

8.2 Materials

8.2.1 Toxicity

There will be no carcinogenic materials used anywhere in the display module. If toxic materials are used, they will be reviewed and approved by the responsible AUO Toxicologist.

8.2.2 Flammability

All components including electrical components that do not meet the flammability grade UL94-V1 in the module will complete the flammability rating exception approval process. The printed circuit board will be made from material rated 94-V1 or better. The actual UL flammability rating will be printed on the printed circuit board.

8.3 Capacitors

www.jxlcd.com

If any polarized capacitors are used in the display assembly, provisions will be made to keep them from being inserted backwards.

21/24

www.DataSheet.co.kr

Datasheet pdf - http://www.DataSheet4U.net/

8.4 Hazardous Voltages

Any point exceeding 42.4 volts meets the requirement of the limited current circuit. The current through a 2KΩ resistance is less than 0.7 x f (kHz) mA.

9.0 Other requirements

9.1 National Test Lab Requirement

The display module will satisfy all requirements for compliance to

UL 1950, First Edition U.S.A. Information Technology Equipment CSA C22.2 No.950-M89 Canada, Information Technology Equipment EEC 950 International, Information Technology Equipment EN 60 950 International, Information Processing Equipment

(European Norm for IEC950)

9.2 Label

9.2.1 Product label

www.jxlcd.com

10.0 Mechanical Characteristic

22/24

www.DataSheet.co.kr

Datasheet pdf - http://www.DataSheet4U.net/

www.jxlcd.com

23/24

www.DataSheet.co.kr

Datasheet pdf - http://www.DataSheet4U.net/

www.jxlcd.com

24/24

www.DataSheet.co.kr

Datasheet pdf - http://www.DataSheet4U.net/

www.jxlcd.com

25/24

AU Optronics M190EN02-V2 Product Specification

Specifications and Main Features

Frequently Asked Questions

User Manual