) Preliminary Specification
( V
( ) Final Specification
Product Specification
AU OPTRONICS CORPORATION
M190EG02 V4
Module
Model Name
19.0” SXGA Color TFT-LCD
M190EG02 V4
Customer Date
www.jxlcd.com
www.jxlcd.com
Approved by
Checked &
Approved by
Prepared by
Date
Note: This Specification is subject to change
without notice.
document version 0.3 1/28
Desktop Display Business Group /
AU Optronics corporation
Product Specification
AU OPTRONICS CORPORATION
M190EG02 V4
Contents
1. Handling Precautions..............................................................................................................4
2. General Description.................................................................................................................5
2.1 Display Characteristics...................................................................................................................6
3. Functional Block Diagram.....................................................................................................11
4. Absolute Maximum Ratings..................................................................................................12
4.1 Absolute Ratings of TFT LCD Module..........................................................................................12
4.2 Absolute Ratings of Backlight Unit................................................................................................12
4.3 Absolute Ratings of Environment..................................................................................................12
5. Electrical characteristics.......................................................................................................14
5.1 TFT LCD Module.........................................................................................................................14
5.2 Backlight Unit...............................................................................................................................15
6. Signal Characteristic.............................................................................................................16
6.1 Pixel Format Image.......................................................................................................................16
6.2 The Input Data Format..................................................................................................................17
6.4 Interface Timing............................................................................................................................19
6.5 Power ON/OFF Sequence.............................................................................................................21
7. Connector & Pin Assignment...............................................................................................22
7.1 TFT LCD Module.........................................................................................................................22
7.2 Backlight Unit...............................................................................................................................23
8. Reliability Test.......................................................................................................................24
9. Shipping Label.......................................................................................................................25
10. Mechanical Characteristic...................................................................................................26
www.jxlcd.com
www.jxlcd.com
document version 0.3 2/28
Product Specification
Color/ Chromaticity Coordinate
Power Sequence Timing is
AU OPTRONICS CORPORATION
Record of Revision
M190EG02 V4
Version & Date Page
0.1 2006/6/23
0.2 2006/9/5 7 Color/ Chromaticity Coordinate
21 Power Sequence Timing
www.jxlcd.com
All First Edition for Customer
www.jxlcd.com
Old Description New Description Remark
update
250ms (max)
document version 0.3 3/28
Product Specification
AU OPTRONICS CORPORATION
M190EG02 V4
1. Handling Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth
when handling.
7) Do not open or modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) In case if a Module has to be put back into the packing container slot after once it was taken out
from the container, do not press the center of the Cold Cathode Fluorescent Lamp (CCFL)
reflector edge. Instead, press at the far ends of the CCFL reflector edge softly. Otherwise the
TFT Module may be damaged.
10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the
Interface Connector of the TFT Module.
11) After installation of the TFT Module into an enclosure, do not twist nor bend the TFT Module
even momentary. At designing the enclosure, it should be taken into consideration that no
bending/twisting forces are applied to the TFT Module from outside. Otherwise the TFT Module
may be damaged.
12) Cold Cathode Fluorescent Lamp (CCFL) in LCD contains a small amount of mercury. Please follow
local ordinances or regulations for disposal.
13) Small amount of materials having no flammability grade is used in the LCD module. The LCD module
should be supplied by power complied with requirements of Limited Power Source (IEC60950 or
UL1950), or be applied exemption.
14) The LCD module is designed so that the CCFL in it is supplied by Limited Current Circuit (IEC60950 or
UL1950). Do not connect the CCFL in Hazardous Voltage Circuit.
www.jxlcd.com
www.jxlcd.com
document version 0.3 4/28
Product Specification
AU OPTRONICS CORPORATION
2. General Description
M190EG02 V4 is a Color Active Matrix Liquid Crystal Display composed of a TFT-LCD panel, a driver
circuit, and a backlight system. The screen format is intended to support the SXGA (1280(H) x 1024(V))
screen and 16.7M colors (RGB 6-bits + HiFRC data). All input signals are LVDS interface compatible.
Inverter card of backlight is not included. M190EG02 V4 is designed for a display unit of personal
computer.
M190EG02 V4
www.jxlcd.com
www.jxlcd.com
document version 0.3 5/28
Product Specification
AU OPTRONICS CORPORATION
M190EG02 V4
2.1 Display Characteristics
The following items are characteristics summary on the table under 25 ℃ condition:
Items Unit Specifications
Screen Diagonal [mm]
Active Area [mm]
Pixels H x V
Pixel Pitch [mm]
Pixel Arrangement
Display Mode
White Luminance [cd/m2] 300 (center, Typ) @ 7.5mA
Contrast Ratio
Optical ResponseTime [msec]
Nominal Input Voltage VDD [Volt]
Power Consumption [Watt]
482.6 (19.0" )
376.32 (H) x 301.06 (V)
1280(x3) x 1024
0.294 (per one triad) x 0.294
R.G.B. Vertical Stripe
Normally White
800 : 1 (Typ)
5 ms(Typ, on/off)
+5.0 V
24.71W (Typ)
(PDD=5.11W, PCFL=19.6 W @Lamp=7.5mA)
Weight [Grams]
Physical Size (H x V x D) [mm]
Electrical Interface
Surface Treatment Hard-coating (3H), Non-Glare treatment
Support Color
Temperature Range
Operating
Storage (Non-Operating)
RoHS Compliance
www.jxlcd.com
www.jxlcd.com
[oC]
[oC]
2400 (Typ) 2500(Max)
396 (H) x 324 (V) x 16.3 (D) (Typ)
Dual channel LVDS
16.7M colors (RGB 6-bit data + HiFRC data)
0 to +50
-20 to +60
RoHS Compliance
document version 0.3 6/28
Product Specification
AU OPTRONICS CORPORATION
M190EG02 V4
2.2 Optical Characteristics
The optical characteristics are measured under stable conditions at 25℃ (Room Temperature):
Item Unit Conditions Min. Typ. Max. Note
Horizontal (Right)
CR = 10 (Left)
Vertical (Up)
CR = 10 (Down)
Viewing Angle [degree]
Vertical (Up)
CR = 5 (Down)
Vertical (Up)
CR = 5 (Down)
Luminance Uniformity [%] 9 Points 75 80 - 2, 3
Rising - 3.6 5.7
Optical Response Time [msec]
www.jxlcd.com
www.jxlcd.com
Falling - 1.4 2.3
Rising + Falling - 5 8
Red x 0.617 0.647 0.677
Red y 0.310 0.340 0.370
Green x 0.258 0.288 0.318
70
70
70
70
75
75
75
75
80
80
80
80
85
85
85
85
-
1
-
-
4, 6
Color / Chromaticity
Coordinates
(CIE 1931)
White Luminance
(At CCFL= 7.5mA)
Contrast Ratio 500 800 - 4
Cross Talk (At 75Hz) [%] - - 1.5 5
Flicker [dB] - - -20
Optical Equipment: BM-5A, BM-7, PR880, or equivalent
document version 0.3 7/28
[cd/m2 ]
Green y 0.575 0.605 0.635
4
Blue x 0.115 0.145 0.175
Blue y 0.041 0.071 0.101
White x 0.283 0.313 0.343
White y 0.299 0.329 0.359
240 300 - 4
7
Product Specification
Minimum
Luminance
of 9 points
=
Max
imum
Luminance
of 9 points
50 %
90 %
90 %
50 %
10 %
10 %
AU OPTRONICS CORPORATION
Note 1: Definition of viewing angle
Viewing angle is the measurement of contrast ratio≧10, or ≧5, at the screen center, over a 180°
horizontal and 180° vertical range (off-normal viewing angles). The 180° viewing angle range is broken
down as follows; 90° (θ) horizontal left and right and 90° (Φ) vertical, high (up) and low (down). The
measurement direction is typically perpendicular to the display surface with the screen rotated about its
center to develop the desired measurement viewing angle.
M190EG02 V4
Note 2: 9 points position
www.jxlcd.com
www.jxlcd.com
Note 3: The luminance uniformity of 9 points is defined by dividing the maximum luminance values by the
minimum test point luminance
document version 0.3 8/28
δ
W9
Product Specification
TFT-LCD
LCD Panel
AU OPTRONICS CORPORATION
Note 4: Measurement method
The LCD module should be stabilized at given temperature for 30 minutes to avoid abrupt temperature
change during measuring. In order to stabilize the luminance, the measurement should be executed after
lighting Backlight for 30 minutes in a stable, windless and dark room.
M190EG02 V4
Photo detector
Field=2°
50 cm
Note 5: Definition of Cross Talk (CT)
CT = | YB – YA | / YA × 100 (%)
Where
YA = Luminance of measured location without gray level 0 pattern (cd/m2)
YB = Luminance of measured location with gray level 0 pattern (cd/m2)
www.jxlcd.com
www.jxlcd.com
Center of the screen
document version 0.3 9/28
Product Specification
R G B R G B R G B R G B
Level
DC
90 10 0 %
Tr
F
R
90 10 0 %
Tr
F
R
AU OPTRONICS CORPORATION
Note 6: Definition of response time:
The output signals of photo detector are measured when the input signals are changed from “Full Black” to
“Full White” (rising time), and from “Full White” to “Full Black” (falling time), respectively. The response
time is interval between the 10% and 90% of amplitudes. Please refer to the figure as below.
M190EG02 V4
Optical
Optical
response
response
Note 7: Subchecker Pattern
R G B R G B
www.jxlcd.com
www.jxlcd.com
100
100
White
White
Gray Level = L127
Gray Level = L0
Black
Black
Tr
Tr
White
White
Method: Record dBV & DC value with (WESTAR)TRD-100
Amplitude
DC
Hz) 30Level(at AC
log20(dB)Flicker =
document version 0.3 10/28
AC
Time
Product Specification
Connector
D1
LVDS
+ 5V
AU OPTRONICS CORPORATION
M190EG02 V4
3. Functional Block Diagram
The following diagram shows the functional block of the 17.0 inches Color TFT-LCD Module:
DC/DC
Converter
www.jxlcd.com
www.jxlcd.com
AU ASIC
LVDS
Timing
Controller
RSDS
Gamma
Correction
DC POWER
G1
G1024
TFT-LCD
1280*(3)*1024
Pixels
D3840
4 CCFL
Inverter
document version 0.3 11/28
Product Specification
Voltage
AU OPTRONICS CORPORATION
4. Absolute Maximum Ratings
Absolute maximum ratings of the module are as following:
4.1 Absolute Ratings of TFT LCD Module
Item Symbol Min. Max. Unit Conditions
M190EG02 V4
Logic/LCD Drive
VDD -0.3 +6 [Volt] Note 1, 2
4.2 Absolute Ratings of Backlight Unit
Item Symbol Min. Max. Unit Conditions
CCFL Current ICFL - 8 [mA] rms Note 1, 2
4.3 Absolute Ratings of Environment
Item Symbol Min. Max. Unit Conditions
Operating Temperature
Operation Humidity HOP 5 90 [%RH]
Storage Temperature TST -20 +60 [
Storage Humidity HST
www.jxlcd.com
www.jxlcd.com
TOP 0 +50 [
5 90
o
C]
o
C]
[%RH]
Note 3
document version 0.3 12/28
Product Specification
AU OPTRONICS CORPORATION
Note 1: With in Ta= 25℃
Note 2: Permanent damage to the device may occur if exceed maximum values
Note 3: For quality performance, please refer to AUO IIS (Incoming Inspection Standard).
M190EG02 V4
Operating Range Storage Range
www.jxlcd.com
www.jxlcd.com
document version 0.3 13/28
Product Specification
10%
0V
5.0V 470 us
M190EG02 V4
AU OPTRONICS CORPORATION
5. Electrical characteristics
5.1 TFT LCD Module
5.1.1 Power Specification
Input power specifications are as follows:
Symble Parameter Min. Typ. Max. Unit Condition
VDD
Logic/LCD Drive
Voltage
4.5 5.0 5.5 [Volt]
IDD Input Current - 1.02 1.34 [A]
PDD VDD Power - 5.11 6.71 [Watt]
IRush Inrush Current - - 2.5 [A] Note 2
VDDrp
Allowable
Logic/LCD Drive
Ripple Voltage
- - 100
[mV]
p-p
Note 1: The variance of VDD power consumption is ±30%.
Note 2: Measurement conditions:
www.jxlcd.com
www.jxlcd.com
(High to Low)
Control
Signal
SW1
SW MAG-SPST
1 2
+12.0V
+5.0V
R1
47K
R2
1K
VR1
47K
D6
D5
D2 S
D1
G
C3
0.01uF/25V
Q3
AO6402
D2SD1D5
G
D6
Q3
AO6402
F1
C1
1uF/16V
±10%
VDD= 5.0V, All Black Pattern
At 75Hz, +30%
VDD= 5.0V, All Black Pattern
At 75Hz , Note 1
VDD= 5.0V, All Black Pattern
At 75Hz
VCC
(LCD Module Input)
C2
1uF/25V
document version 0.3 14/28
Vin rising time
Product Specification
AU OPTRONICS CORPORATION
M190EG02 V4
5.2 Backlight Unit
Parameter guideline for CCFL Inverter is under stable conditions at 25 (Room Tempera℃ ture):
Parameter Min. Typ. Max. Unit Condition
CCFL Standard Current(ISCFL) 7.0 7.5 8.0 [mA] rms Note 2
CCFL Operation Current(IRCFL) 3.0 7.5 8.0 [mA] rms Note 2
CCFL Frequency(FCFL) 40 60 80 [KHz] Note 3,4
CCFL Ignition Voltage(ViCFL, Ta= 0)℃ 1690 - - [Volt] rms
Note 5
CCFL Ignition Voltage(ViCF, Ta= 25)℃ 1300 - - [Volt] rms
CCFL Operation Voltage (VCFL) -
CCFL Power Consumption(PCFL) - 19.6 21.56 [Watt] Note 6
CCFL Life Time(LTCFL) 40,000 50,000 - [Hour] Note 7
Note 1: Typ. are AUO recommended design points.
*1 All of characteristics listed are measured under the condition using the AUO test inverter.
*2 In case of using an inverter other than listed, it is recommended to check the inverter carefully.
www.jxlcd.com
Sometimes, interfering noise stripes appear on the screen, and substandard luminance or flicker
www.jxlcd.com
at low power may happen.
*3 In designing an inverter, it is suggested to check safety circuit very carefully. Impedance of
CCFL, for instance, becomes more than 1 [M ohm] when CCFL is damaged.
*4 Generally, CCFL has some amount of delay time after applying kick-off voltage. It is
recommended to keep on applying kick-off voltage for 1 [Sec] until discharge.
*5 Reducing CCFL current increases CCFL discharge voltage and generally increases CCFL
discharge frequency. So all the parameters of an inverter should be carefully designed so as
not to produce too much leakage current from high-voltage output of the inverter.
Note 2: CCFL standard current is measured at 25±2℃.
Note 3: CCFL discharge frequency should be carefully determined to avoid interference between inverter
and TFT LCD.
653
(@ 7.5mA)
796
(@ 3.0mA)
[Volt] rms Note 6
Note 4: The frequency range will not affect to lamp life and reliability characteristics.
Note 5: CCFL inverter should be able to give out a power that has a generating capacity of over 1,690
voltage. Lamp units need 1,690 voltage minimum for ignition.
Note 6: The variance of CCFL power consumption is ±10%. Calculator value for reference (ISCFL × VCFL
× 4 = PCFL)
Note 7: Definition of life: brightness becomes 50% or less than the minimum luminance value of CCFL.
The typical life time of CCFL is on the condition at 7.5 mA lamp current.
document version 0.3 15/28
Product Specification
R G B R G B R G B R G B R G B R G B 0 1
AU OPTRONICS CORPORATION
6. Signal Characteristic
6.1 Pixel Format Image
Following figure shows the relationship of the input signals and LCD pixel format.
M190EG02 V4
1279 1280
1st Line
1024th Line
www.jxlcd.com
www.jxlcd.com
R G B R G B
document version 0.3 16/28
6.2 The Input Data Format
Product Specification
AU OPTRONICS CORPORATION
M190EG02 V4
Note1: Normally, DE, VS, HS on EVEN channel are not used.
Note2: Please follow PSWG.
Note3: 8-bit in
www.jxlcd.com
www.jxlcd.com
document version 0.3 17/28
Product Specification
AU OPTRONICS CORPORATION
M190EG02 V4
6.3 Signal Description
The module using a pair of LVDS receiver SN75LVDS82(Texas Instruments) or compatible. LVDS is a
differential signal technology for LCD interface and high speed data transfer device. Transmitter shall be
SN75LVDS83(negative edge sampling) or compatible. The first LVDS port(RxOxxx) transmits odd pixels
while the second LVDS port(RxExxx) transmits even pixels.
PIN # SIGNAL NAME DESCRIPTION
1 RxOIN0- Negative LVDS differential data input (Odd data)
2 RxOIN0+ Positive LVDS differential data input (Odd data)
3 RxOIN1- Negative LVDS differential data input (Odd data)
4 RxOIN1+ Positive LVDS differential data input (Odd data)
5 RxOIN2- Negative LVDS differential data input (Odd data, H-Sync,V-Sync,DSPTMG)
6 RxOIN2+ Positive LVDS differential data input (Odd data, H-Sync,V-Sync,DSPTMG)
7 VSS Power Ground
8 RxOCLKIN- Negative LVDS differential clock input (Odd clock)
9 RxOCLKIN+ Positive LVDS differential clock input (Odd clock)
10 RxOIN3- Negative LVDS differential data input (Odd data)
11 RxOIN3+ Positive LVDS differential data input (Odd data)
12 RxEIN0- Negative LVDS differential data input (Even data)
13 RxEIN0+ Positive LVDS differential data input (Even data)
14 VSS Power Ground
15 RxEIN1- Negative LVDS differential data input (Even data)
16 RxEIN1+ Positive LVDS differential data input (Even data)
17 VSS Power Ground
18 RxEIN2- Negative LVDS differential data input (Even data)
19 RxEIN2+ Positive LVDS differential data input (Even data)
20 RxECLKIN- Negative LVDS differential clock input (Even clock)
21 RxECLKIN+ Positive LVDS differential clock input (Even clock)
22 RxEIN3- Negative LVDS differential data input (Even data)
23 RxEIN3+ Positive LVDS differential data input (Even data)
24 VSS Power Ground
25 VSS Power Ground
www.jxlcd.com
www.jxlcd.com
26 NC No Connection ( for AUO test)
27 VSS Power Ground
28 VCC +5.0V Power Supply
29 VCC +5.0V Power Supply
30 VCC +5.0V Power Supply
document version 0.3 18/28
Connector
RxO
IN
0
-
VCC
Note1: Start from left side
Product Specification
AU OPTRONICS CORPORATION
M190EG02 V4
Note2: Input signals of odd and even clock shall be the same timing.
Note3: Please follow PSWG.
www.jxlcd.com
www.jxlcd.com
30
6.4 Interface Timing
6.4.1 Timing Characteristics
Item Symbol Min Typ Max Unit
Data CLK Tclk 40 54 67.5 MHz
H-section
V-section
Frame Rate F 50 60 75 Hz
Note : DE mode only
Period Th 680 844 1024 Tclk
Display Area Tdisp(h) 640 640 640 Tclk
Period Tv 1028 1066 2048 Th
Display Area Tdisp(v) 1024 1024 1024 Th
document version 0.3 19/28
6.4.2 Timing Digram
RGB Data
(Even)
RGB Data
(Odd)
Product Specification
M190EG02 V4
AU OPTRONICS CORPORATION
Hsync
DE
CLK
RGB Data
Line LineLineLineLine Line
N
DE
Hsync
Vsync
PWhs
Invalid Data
Invalid Data
Tbp(h)
Pixel
Pixel
2
1
PixelPixel
Pixel
3 9 M-1
4
Pixel
65
PixelPixelPixel PixelPixelPixel
www.jxlcd.com
www.jxlcd.com
7
8
10
12
11
Tdisp(h)
Tclk
Invalid Data
2
43
Tfp(v)
PWvs
Tbp(v)
Tdisp(v)
Tv
PixelPixelPixelPixel
M-5
M-4
M-2
M-3
M
document version 0.3 20/28
PixelPixel
Tfp(h)
Invalid Data
Invalid Data
N1
Th
Invalid Data
Product Specification
T5 T2
T1
T6
AU OPTRONICS CORPORATION
M190EG02 V4
6.5 Power ON/OFF Sequence
VDD power and lamp on/off sequence is as follows. Interface signals are also shown in the chart. Signals
from any system shall be Hi-Z state or low level when VDD is off.
VALID
DATA
Value
90%
10%
T7
T4
Unit
Power Supply VDD
LVDS Signal
Backlight On
Parameter
90%
10%
T3
www.jxlcd.com
www.jxlcd.com
Power Sequence Timing
Min. Typ. Max.
T1 0.5 - 10 [ms]
T2 0 - 50 [ms]
T3 - - 250 [ms]
T4 - - 250 [ms]
T5 0 16 50 [ms]
T6 - - 10 [ms]
T7 500 - - [ms]
Note: The values of the table are follow PSWG.
document version 0.3 21/28
Product Specification
AU OPTRONICS CORPORATION
M190EG02 V4
7. Connector & Pin Assignment
Physical interface is described as for the connector on module.These connectors are capable of
accommodating the following signals and will be following components.
7.1 TFT LCD Module
7.1.1 Connector
Connector Name / Designation Interface Connector / Interface card
Manufacturer JAE or compatible
Type Part Number FI-XB30SSL-HF15
Mating Housing Part Number FI-X30HL
7.1.2 Pin Assignment
Pin# Signal Name Pin# Signal Name
1 RxOIN0- 2 RxOIN0+
3 RxOIN1- 4 RxOIN1+
5 RxOIN2- 6 RxOIN2+
7 VSS 8 RxOCLKIN-
9 RxOCLKIN+ 10 RxOIN311 RxOIN3+ 12 RxEIN013 RxEIN0+ 14 VSS
15 RxEIN1- 16 RxEIN1+
17 VSS 18 RxEIN219 RxEIN2+ 20 RxECLKIN21 RxECLKIN+ 22 RxEIN3-
23 RxEIN3+ 24 VSS
25 VSS 26 NC
27 VSS 28 VCC
29 VCC 30 VCC
www.jxlcd.com
www.jxlcd.com
document version 0.3 22/28
Product Specification
AU OPTRONICS CORPORATION
M190EG02 V4
7.2 Backlight Unit
Physical interface is described as for the connector on module. These connectors are capable of
accommodating the following signals and will be following components.
Connector Name / Designation Lamp Connector / Backlight lamp
Manufacturer JST
Type Part Number BHSR-02VS-1
Mating Type Part Number
7.2.1 Signal for Lamp connector
Connector No. Pin No. Input Color Function
1 Hot1 Pink High Voltage
2 Cold1 White Low Voltage
1 Hot2 Pink High Voltage
2 Cold2 White Low Voltage
Upper
CN1
CN2
www.jxlcd.com
www.jxlcd.com
Connector No. Pin No. Input Color Function
CN3
Lower
CN4
1 Hot1 Pink High Voltage
2 Cold1 White Low Voltage
1 Hot2 Pink High Voltage
2 Cold2 White Low Voltage
SM02B-BHSS-1-TB
document version 0.3 23/28
Product Specification
AU OPTRONICS CORPORATION
8. Reliability Test
Environment test conditions are listed as following table.
Items Required Condition
Temperature Humidity Bias (THB) Ta= 50, ℃ 80%RH, 300hours
M190EG02 V4
Note
High Temperature Operation (HTO) Ta= 50, ℃ 50%RH, 300hours
Low Temperature Operation (LTO) Ta= 0, 300hours℃
High Temperature Storage (HTS) Ta= 60, 300hours℃
Low Temperature Storage (LTS) Ta= -20, 300hours℃
Acceleration: 1.5 G
Vibration Test
(Non-operation)
Shock Test
(Non-operation)
Drop Test Height: 60 cm, package test
Thermal Shock Test (TST) -20℃/30min, 60℃/30min, 100 cycles
On/Off Test On/10sec, Off/10sec, 30,000 cycles
ESD (ElectroStatic Discharge)
www.jxlcd.com
www.jxlcd.com
Wave: Random
Frequency: 10 - 200 - 10 Hz
Sweep: 30 Minutes each Axis (X, Y, Z)
Acceleration: 50 G
Wave: Half-sine
Active Time: 20 ms
Direction: ±X, ±Y, ±Z (one time for each Axis)
Contact Discharge: ± 8KV, 150pF(330Ω ) 1sec,
8 points, 25 times/ point.
Air Discharge: ± 15KV, 150pF(330Ω ) 1sec
8 points, 25 times/ point.
1
2
Altitude Test
Note 1: The TFT-LCD module will not sustain damage after being subjected to 100 cycles of rapid
temperature change. A cycle of rapid temperature change consists of varying the temperature from
-20℃ to 60℃, and back again. Power is not applied during the test. After temperature cycling, the
unit is placed in normal room ambient for at least 4 hours before power on.
Note 2: According to EN61000-4-2 , ESD class B: Some performance degradation allowed. No data lost.
Self-recoverable. No hardware failures.
document version 0.3 24/28
Operation:10,000 ft
Non-Operation:30,000 ft
Product Specification
AU OPTRONICS CORPORATION
9. Shipping Label
The shipping label format is shown as below.
M190EG02 V4
www.jxlcd.com
www.jxlcd.com
document version 0.3 25/28
Product Specification
AU OPTRONICS CORPORATION
10. Mechanical Characteristic
M190EG02 V4
www.jxlcd.com
www.jxlcd.com
document version 0.3 26/28
Product Specification
AU OPTRONICS CORPORATION
M190EG02 V4
document version 0.3 27/28
www.jxlcd.com
www.jxlcd.com
Product Specification
AU OPTRONICS CORPORATION
M190EG02 V4
www.jxlcd.com
www.jxlcd.com
document version 0.3 28/28
Loading...