Product Specification
M150XN07 V.2
AU OPTRONICS CORPORATION
Product Specification
15.0” XGA Color TFT-LCD Module
Model Name: M150XN07 V.2
Approved by Prepared by
www.jxlcd.com
www.jxlcd.com
CC Chiu
TC Tsai
DDBU Marketing Division / AU Optronics corporation
Customer Checked & Approved by
ver 0.1 1/29
M150XN07 V.2
) Preliminary Specifications
Product Specification
Product Specification
15.0” XGA Color TFT-LCD Module
Model Name: M150XN07
(u
( ) Final Specifications
Note: This Specification is subject to change without notice.
www.jxlcd.com
www.jxlcd.com
V.2
ver 0.1 2/29
Product Specification
M150XN07 V.2
Contents
1.0 Handling Precautions.............................................................5
2.0 General Description...............................................................6
2.1 Display Characteristics..............................................................................................................6
2.2 Optical Characteristics
3.0 Functional Block Diagram....................................................12
4.0 Absolute Maximum Ratings.................................................13
4.1 TFT LCD Module......................................................................................................................13
4.2 Backlight Unit
4.3 Absolute Ratings of Environment............................................................................................13
............................................................................................................................13
5.0 Electrical characteristics......................................................14
5.1 TFT LCD Module......................................................................................................................14
5.1.1 Power Specification.............................................................................................................................14
5.1.2 Signal Electrical Characteristics...........................................................................................................15
5.2 Backlight Unit
............................................................................................................................16
6.0 Signal Characteristic............................................................17
6.1 Pixel Format Image
6.2 The input data format...............................................................................................................18
6.3 Signal Description
6.4 Interface Timing........................................................................................................................20
www.jxlcd.com
www.jxlcd.com
...............................................................................................................7
...................................................................................................................17
....................................................................................................................19
6.4.1 Timing Characteristics.........................................................................................................................20
6.4.2 Timing diagram....................................................................................................................................21
6.5 Power ON/OFF Sequence
.......................................................................................................22
7.0 Connector & Pin Assignment...............................................23
7.1 TFT LCD Module
7.2 Backlight Unit............................................................................................................................24
7.3 Signal for Lamp connector
......................................................................................................................23
.......................................................................................................24
8.0 Reliability............................................................................25
9.0 Safety..................................................................................26
9.1 Sharp Edge Requirements ......................................................................................................26
9.2 Materials
9.2.1 Toxicity................................................................................................................................................26
9.2.2 Flammability........................................................................................................................................26
9.3 Capacitors .................................................................................................................................26
....................................................................................................................................26
10.0 Other requirement.............................................................26
10.1 National Test Lab Requirement.............................................................................................26
10.2 Label
........................................................................................................................................26
ver 0.1 3/29
Product Specification
M150XN07 V.2
11.0 Mechanical Characteristics................................................27
Record of Revision
Version and Date Page
0.1 2005/02/14 All First Edition for Customer
Old description New Description Remark
www.jxlcd.com
www.jxlcd.com
ver 0.1 4/29
Product Specification
M150XN07 V.2
1.0 Handling Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth when
handling.
7) Do not open nor modify the Module Assembly.
8) Do not press or pat the panel surface by fingers,hand or tooling.
9) Do not press the reflector sheet at the back of the module to any directions.
10) In case if a module has to be put back into the packing container slot after once it was taken out from the
container, do not press the center of the CCFL reflector edge. Instead, press at the far ends of the CCFL
reflector edge softly. Otherwise the TFT module may be damaged.
11) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the Interface
Connector of the TFT module.
12) After installation of the TFT module into an enclosure (Desktop monitor Bezel, for example), do not twist
nor bend the TFT Module even momentary. At designing the enclosure, it should be taken into
consideration that no bending/twisting forces are applied to the TFT module from outside. Otherwise the
TFT module may be damaged.
www.jxlcd.com
www.jxlcd.com
ver 0.1 5/29
M150XN07 V.2
Product Specification
2.0 General Description
This specification applies to the 15.0 inch Color TFT/LCD Module M150XN07 V2.
This module is designed for a display unit of personal computer.
The display supports the XGA (1024 (H) x 768(V)) screen format and 16.2M colors (RGB 6-bits + FRC data).
All input signals are 1 Channel LVDS interface compatible.
This module does not contain an inverter card for backlight.
2.1 Display Characteristics
The following items are characteristics summary on the table under 25 ℃ condition:
ITEMS Unit SPECIFICATIONS
Screen Diagonal [mm] 381 (15”)
Active Area [mm] 304.128 (H) x 228.096
Pixels H x V 1024(x3) x 768
Pixel Pitch [mm] 0.297 (per one triad) x 0.297
Pixel Arrangement R.G.B. Vertical Stripe
Display Mode TN mode, Normally White
White Luminance [cd/m2] 250 (Typ) @ 8mA
Contrast Ratio 500 : 1 (Typ)
Optical Rise Time/Fall Time [msec] 12 (Typ) (Note 1)
Color Saturation 65% NTSC
Nominal Input Voltage VDD [Volt] +3.3 V
Power Consumption
(VDD line + CCFL line)
Weight [Grams] 1100 (Typ)
Physical Size [mm]
www.jxlcd.com
www.jxlcd.com
Electrical Interface 1 Channel LVDS
Support Color 16.2M colors (RGB 6-bit + FRC data)
Temperature Range
Operating
Storage (Shipping)
Surface Treatment Hard-coating (3H), anti-glare treatment
Note 1 :System should warm up for at least one hour
[Watt]
[oC]
[oC]
13.3 W (Typ.) @8mA (All Black Pattern)
Min. Typ. Max.
Horizatal(H) 326.0 326.5 327.0
Vertical(V) 253.0 253.5 254.0
Depth(D) - - 12.0
0 to +50
-20 to +60
ver 0.1 6/29
M150XN07 V.2
Product Specification
2.2 Optical Characteristics
The optical characteristics are measured under stable conditions at 25℃ (Room Temperature):
Item Unit Conditions Min. Typ. Max. Note
Horizontal (Right)
CR = 10 (Left)
TBD
65
65
-
Vertical (Up)
Viewing Angle [degree]
Contrast ratio Normal Direction TBD 500
Response Time
Color / Chromaticity
Coordinates (CIE)
Color Coordinates (CIE)
White
White Luminance @ CCFL
8mA (center)
Luminance Uniformity
Crosstalk (in 75Hz)
Flicker
Equipment Pattern Generator, Power Supply, Digital Voltmeter, Luminance meter (PR 880, BM-5A ,
www.jxlcd.com
www.jxlcd.com
[msec]
[cd/m2]
[%] 75 80
[%] 1.2 1.5
dB -20
CR = 10 (Down)
Horizontal (Right)
CR = 5 (Left)
Vertical (Up)
CR = 5 (Down)
Rising Time
Falling Time
Rising + Falling
Red x
Red y
Green x
Green y
Blue x
Blue y
White x
White y
200 250
TBD
TBD TBD
TBD TBD
-
- TBD TBD
- 12
0.61 0.64 0.67
0.30
0.27
0.56 0.59 0.62
0.12
0.07
0.28 0.31 0.34
0.30
65
55
TBD TBD
0.33 0.36
0.30 0.33
0.15 0.18
0.10 0.13
0.33 0.36
keep total
-
120(Mayb
e 60,60)
Note 1
-
Note 2
Note 3
Note 4
BM 7 ,CS-1000, CA210, SR_3 & EZ Contrast(ELDIM)* )
Aperture 1
Test Point Center (VESA point 9)
Environment < 1 lux
∘
with 50cm viewing distance
LCD Module
PR-880 /
BM5A /
BM7
measuring distance
Module Driving Equipment
ver 0.1 7/29
M150XN07 V.2
*’ EZ Contrast is different measurement tool with very close viewing distance.
Product Specification
www.jxlcd.com
www.jxlcd.com
ver 0.1 8/29
M150XN07 V.2
90 %
90 10 0 %
Tr
F
R
90 10 0 %
Tr
F
R
Note 1: Definition of Response time
The output signals of photo detector are measured when the input signals are changed from “Black” to “White”
(rising time), and from “White” to “Black ”(falling time), respectively. The response time is interval between the
10% and 90% of amplitudes.
100
100
Optical
Optical
response
response
Note 2: Brightness uniformity of these 9 points is defined as below
White
White
Product Specification
Black
Black
Tr
Tr
White
White
90 %
www.jxlcd.com
www.jxlcd.com
50 %
10 %
10 %
50 %
Uniformity ×=
9)-(1 points 9in Luminance Minimum
%100
9)-(1 Points 9in Luminance Maximum
ver 0.1 9/29
M150XN07 V.2
R G B R G B R G B R G B
1/2
1/2
1/6 1/6
A
B
1/2
1/2
1/6
1/6
2/3 1/3
1/3
2/3
A’
B’
Note 3: Crosstalk is defined as below :
l LA-LA’ l / LA x 100%= 1.5% max., LA and LB are brightness at location A and B
l LB-LB’ l / LB x 100%= 1.5% max., LA’ and LB’ are brightness at location A’ and B’
Note 4: Test Paterm: Subchecker Pattern at 127 gray level
184 gray level 184 gray level
Unit: percentage of dimension of display area
www.jxlcd.com
30mm
www.jxlcd.com
CA210
Sub Checker Pattern
Product Specification
A
0
0 gray level
FFT
A
30
R G B R G B
Gray Level = L127
Gray Level = L0
ver 0.1 10/29
M150XN07 V.2
Level
DC
AC
Amplitude
Product Specification
DC
Time
Hz) 30Level(at AC
log20(dB)Flicker =
www.jxlcd.com
www.jxlcd.com
ver 0.1 11/29
M150XN07 V.2
Connector
D1
LVDS
Product Specification
3.0 Functional Block Diagram
The following diagram shows the functional block of the 15.0 inches wide Color TFT/LCD Module:
+ 3.3V
DC/DC
Converter
www.jxlcd.com
www.jxlcd.com
LVDS
AU ASIC
Gamma
Correction
Timing
Controller
RSDS
DC POWER
G1
G768
TFT-LCD
1024(3)*768
Pixels
Inverter
D3072
2 CCFL
CWY20G – A0G16 / MSB240420 JST-BHR-03VS-1
Mating Type
: HRS DF14-20S-1.25C SM02(8.0)B-BHS-1-TB
ver 0.1 12/29
M150XN07 V.2
Item Symbol
Min Max Unit Conditions
Item Symbol
Min Max Unit Conditions
Item Symbol
Min Max Unit Conditions
Product Specification
4.0 Absolute Maximum Ratings
Absolute maximum ratings of the module is as following:
4.1 TFT LCD Module
Logic/LCD Drive
VDD 0.3 +3.6 [Volt] Note 1,2
4.2 Backlight Unit
CCFL Current IRCFL - 8.5 [mA] rms Note 1,2
4.3 Absolute Ratings of Environment
Operating Temperature
Operating Humidity HOP 8 90 [%RH] Note 3
Storage Temperature TST -20 +60 [
Storage Humidity HST 8 90 [%RH] Note 3
Note 1: With in Ta (25℃ )
Note 2: Permanent damage to the device may occur if exceed maximum values
Note 3: For quality perfermance, please refer to AUO IIS(Incoming Inspection Standard) . Please refer the
www.jxlcd.com
www.jxlcd.com
TOP 0 +50 [
o
C] Note 3
o
C] Note 3
graph below for the corresponding of temperature and humidity."
ver 0.1 13/29
M150XN07 V.2
90% 10%
Vin rising time
0V
3.3V
470
us
5.0 Electrical characteristics
5.1 TFT LCD Module
5.1.1 Power Specification
Input power specifications are as follows;
Product Specification
Symbol Parameter Min Typ Max Units
VDD Logic/LCD Drive
3.0 3.3 3.6 [Volt]
±
10%
Condition
Voltage
IDD VDD current - 600 700 [mA] Vin=3.3V , Gray Bar Pattern,
at 60Hz
Irush LCD Inrush Current
PDD VDD Power
VDDrp Allowable
Logic/LCD Drive
Ripple Voltage
- - 3 [A] Note
2.0
2.3 [Watt] Vin=3.3V , Gray Bar Pattern,
at 60Hz
100 [mV]
p-p
Vin=3.3V , All Black Pattern,
at 75Hz
Note: Measurement conditions:
www.jxlcd.com
www.jxlcd.com
(High to Low)
Control Signal
SW
+12.0V
+5.0V
+3.3V
R1
47K
R2
1K
D6
D5
D2 S
D1
G
C3
Q3
AO6402
D2SD1D5
G
D6
Q3
AO6402
F1
VCC
(LCD Module Input)
C1
1uF/16V
VR1
C2
1uF/25V
47K
0.01uF/25V
ver 0.1 14/29
M150XN07 V.2
│
VID│
VSS
Product Specification
5.1.2 Signal Electrical Characteristics
Input signals shall be low or Hi-Z state when Vin is off
It is recommended to refer the specifications of SN75LVDS82DGG (Texas Instruments) in detail.
Each signal characteristics are as follows;
Symbol Parameter Min Typ Max Units
VTH
VTL
│VID│
VICM
Note: LVDS Signal Waveform
VTH
VTL
Differential Input
High Threshold
Differential Input
Low Threshold
Input Differential
Voltage
Differential Input
Common Mode
Voltage
VICM
www.jxlcd.com
www.jxlcd.com
- -
-100 100 400 600 [mV]
1.1 - 1.45 [V]
100 [mV]
- [mV]
Condition
VICM = 1.2V Note
VICM = 1.2V Note
Note
VTH/VTL = ± 100mV Note
ver 0.1 15/29
M150XN07 V.2
Product Specification
5.2 Backlight Unit
Parameter guideline for CCFL Inverter
Symbol Parameter Min. Typ. Max. Unit Condition
IRCFL CCFL operation range
ICFL CCFL Inrush current
FCFL CCFL Frequency
ViCFL
(0oC)
(reference)
ViCF
(25oC)
(reference)
VCFL
PCFL
Note 1: CCFL frequency should be carefully determined to avoid interference between inverter and TFT LCD.
Note 2: Calculator value for reference (IRCFLxVCFLx2=PCFL).
www.jxlcd.com
CCFL Ignition Voltage
CCFL Ignition Voltage
CCFL Discharge Voltage
CCFL Power consumption
@8mA(excluding inverter)
www.jxlcd.com
2.5 8 8.5
- - 20
40 55 80
1450 - -
1100 - -
-
620
(@8mA)
- 10 11 [Watt] (Ta=25oC) Note 2
710
(@2.5mA)
[mA]
rms
[mA]
[KHz] (Ta=25oC) Note 1
[Volt]
rms
[Volt]
rms
[Volt]
rms
(Ta=25oC)
Note 4
(Ta=0oC) Note 3
(Ta=25oC) Note 3
(Ta=25oC) Note 2
Note 3: CCFL inverter should be able to give output a voltage more than 1450 volt. Lamp units need 1450 volt
minimum for ignition.
Note 4: CCFL life time is 30,000hr at 8.0mA, it’s defined as when the brightness is reduced by half. It ’s recommended
not to exceed 8.0mA for CCFL life time concern and it ’s prohibited to exceed 8.5mA for safety concern.
ver 0.1 16/29
M150XN07 V.2
Product Specification
6.0 Signal Characteristic
6.1 Pixel Format Image
Following figure shows the relationship of the input signals and LCD pixel format.
www.jxlcd.com
www.jxlcd.com
ver 0.1 17/29
M150XN07 V.2
6.2 The input data format
CLKIN+
CLKIN-
Product Specification
RIN0 +/-
RIN1 +/-
RIN2 +/-
RIN3 +/-
OG0 OR5OR4OR3OR2OR1OR0
OB0 OG3OG4OG1OG2OB1 OG5
DEVSHS
Rsvd
Current Cycle
Note1: Please follow PSWG.
Note2: 8-bit in
Note3: R/G/B data 7:MSB, R/G/B data 0:LSB
www.jxlcd.com
www.jxlcd.com
OB5OB3OB4OB2
OR7OB7 OR6OB6 OG7OG6
ver 0.1 18/29
M150XN07 V.2
Product Specification
6.3 Signal Description
The module using a pair of LVDS receiver SN75LVDS82(Texas Instruments) or compatible. LVDS is a differential
signal technology for LCD interface and high speed data transfer device. Transmitter shall be SN75LVDS83(negative
edge sampling) or compatible. The first LVDS port(RxOxxx) transmits odd pixels while the second LVDS
port(RxExxx) transmits even pixels.
CWY20G-A0D1T (PTWO) or MSB240420 (STM)
Pin No. Symbol Description
1 VDD Power Supply, 3.3V (typical)
2 VDD
3 VSS Ground
4 VSS
5 Rin06 Rin0+ + LVDS differential data input (R0-R5, G0)
7 VSS
8 Rin1- - LVDS differential data input (G1-G5, B0-B1)
9 Rin1+ + LVDS differential data input (G1-G5, B0-B1)
10 VSS
11 Rin2- - LVDS differential data input (B2-B5, HS, VS, DE)
12 Rin2+
13 VSS
14 ClkIN- - LVDS differential clock input
www.jxlcd.com
15 ClkIN+
16 VSS Ground
17 Rin318 Rin3+
www.jxlcd.com
Power Supply, 3.3V (typical)
Ground
- LVDS differential data input (R0-R5, G0)
Ground
Ground
+ LVDS differential data input (B2-B5, HS, VS, DE)
Ground
+ LVDS differential clock input
- LVDS differential data input (R6-R7, G6-G7,B6-B7)
- LVDS differential data input (R6-R7, G6-G7,B6-B7)
19 VSS Ground
20 VSS
Note: Please follow PSWG.
Ground
ver 0.1 19/29
M150XN07 V.2
Product Specification
6.4 Interface Timing
6.4.1 Timing Characteristics
Basically, interface timings described here is not actual input timing of LCD module but output timing of
SN75LVDS82DGG (Texas Instruments) or equivalent.
Signal Parameter Symbol MIN TYP MAX Unit
Clock Timing Clock frequency
Hsync Timing
Vsync Timing
Note:DE mode only
Note: Typical value refer to VESA STANDARD
Horizontal active
Horizontal blanking
Horizontal period
Vertical active
Vertical blanking
Vertical period
clk 50 65 81 MHz
Thd 1024 1024 1024 Tclk
Thbl 40 320 400 Tclk
Th 1064 1344 1424 Tck
Tvd 768 768 768 Th
Tvbl 8 38 75 Th
Tv 776 806 843 Th
www.jxlcd.com
www.jxlcd.com
ver 0.1 20/29
M150XN07 V.2
6.4.2 Timing diagram
Product Specification
www.jxlcd.com
www.jxlcd.com
ver 0.1 21/29
M150XN07 V.2
10%
10%
90%
90%
1sec
6.5 Power ON/OFF Sequence
Vin power and lamp on/off sequence is as follows. Interface signals are also shown in the chart. Signals from
any system shall be Hi-Z state or low level when Vin is off.
Vin
0 V
Product Specification
min.
Signal
Lamp
On
10%
0 min.
200ms
10%
10ms max.
0 min.
0 V
0 V
www.jxlcd.com
10%
www.jxlcd.com
ver 0.1 22/29
M150XN07 V.2
Product Specification
7.0 Connector & Pin Assignment
Physical interface is described as for the connector on module.
These connectors are capable of accommodating the following signals and will be following components.
7.1 TFT LCD Module
Connector Name / Designation
Manufacturer P-TWO or compatible
Type Part Number
Mating Housing Part Number HRS DF14-20S-1.25C
Pin# Signal Name Pin# Signal Name
1
3
5
7
9
11
13
15
17
19
VDD
VSS
Rin0-
VSS
Rin1+
Rin2-
VSS
www.jxlcd.com
ClkIN+
www.jxlcd.com
Rin3-
VSS
Interface Connector / Interface card
CWY20G – A0G16 / MSB240420
2 VDD
4 VSS
6
8 Rin110 VSS
12 Rin2+
14
16 VSS
18 Rin3+
20 VSS
Rin0+
ClkIN-
ver 0.1 23/29
M150XN07 V.2
7.2 Backlight Unit
Connector Name / Designation
Product Specification
For Lamp Connector
Manufacturer
Type / Part Number
Mating Type / Part Number
7.3 Signal for Lamp connector
Pin Symbol Description
1 HV Lamp High Voltage
2 NC No connection
3 LV Ground
Cable length: 140 +- 5 mm
u
Connector-output position: right side (front view)
u
Lamp assembly design shall be easy for replacement and repair.
u
www.jxlcd.com
www.jxlcd.com
JST or compatible
BHR-03VS-1
SM02(8.0)B-BHS-1-TB
ver 0.1 24/29
M150XN07 V.2
Product Specification
8.0 Reliability
Reliability test condition
No Test Item Test Condition
1 Temperature Humidity Bias (THB)
2 High Temperature Operation (HTO)
3 Low Temperature Operation (LTO)
4 High Temperature Storage (HTS)
5 Low Temperature Storage (LTS)
6 Thermal Shock Test (TST)
7 On/Off Test On/10sec, Off/10sec, 30,000 cycles
8 Shock Test (Non-Operating) 50G, 20ms, Half-sine wave (+ X, +Y, +Z)
9 Vibration Test (Non-Operating) 1.5G(10~200Hz P- P), 30 Minutes each Axis (X, Y, Z)
10 ESD (ElectroStatic Discharge) Contact Discharge: ± 8KV, 150pF(330Ω ) 1sec, 8 points, 25 times/ point
11 Altitude Test Operation:10,000 ft
50℃, 80%, 300hours
50℃, 300hours
0℃, 300hours
60℃, 300hours
-20℃, 300hours
-20℃/30min, 60℃/30min, 100 cycles
Air Discharge: ± 15KV, 150pF(330Ω ) 1sec, 8 points, 25 times/ point
Non-Operation:30,000 ft
12 Drop Test The drop height is 60cm
www.jxlcd.com
www.jxlcd.com
ver 0.1 25/29
M150XN07 V.2
9.0 Safety
9.1 Sharp Edge Requirements
There will be no sharp edges or comers on the display assembly that could cause injury.
9.2 Materials
9.2.1 Toxicity
There will be no carcinogenic materials used anywhere in the display module. If toxic materials
are used, they will be reviewed and approved by the responsible AUO Toxicologist.
9.2.2 Flammability
All components including electrical components that do not meet the flammability grade
UL94-V1 in the module will complete the flammability rating exception approval process.
The printed circuit board will be made from material rated 94-V1 or better. The actual UL
flammability rating will be printed on the printed circuit board.
Product Specification
9.3 Capacitors
If any polarized capacitors are used in the display assembly, provisions will be made to keep
them from being inserted backwards.
10.0 Other requirement
www.jxlcd.com
10.1 National Test Lab Requirement
10.2 Label
The label is on the panel as shown below:
www.jxlcd.com
The display module will satisfy all requirements for compliance to
UL 1950, First Edition U.S.A. Information Technology Equipment
CSA C22.2 No.950-M89 Canada, Information Technology Equipment
EEC 950 International, Information Technology Equipment
EN 60 950 International, Information Processing Equipment
(European Norm for IEC950)
ver 0.1 26/29
11.0 Mechanical Characteristics
www.jxlcd.com
www.jxlcd.com
Ver0.2 27/29
www.jxlcd.com
www.jxlcd.com
Ver0.2 28/29
www.jxlcd.com
www.jxlcd.com
Ver0.2 29/29
Loading...