Page 1
AU OPTRONICS CORPORATION
) Preliminary Specifications
(
(V ) Final Specifications
Module
15.4” W XGA+ Color TFT-LCD
Product Specification
Model Name
Dell P/N
Customer Date
www.jxlcd.com
Checked &
Approved by
B154PW04 V3
HW663
www.jxlcd.com
Date
Approved by Date
Jerry Chen 4/30/2008
Prepared by Date
Wisdom Che 4/30/2008
Note: This Specification is subject to change without
notice.
AUO NBBU spec. Template 1.0
NBBU Marketing Division /
AU Optronics corporation
1 of 36
Page 2
AU OPTRONICS CORPORATION
Product Specification
Contents
1. Handling Precautions .............................................................. 4
2. General Description ................................................................ 5
2.1 General Specification ..........................................................................................................................5
2.2 Optical Characteristics ........................................................................................................................6
3. Functional Block Diagram ..................................................... 11
4. Absolute Maximum Ratings................................................... 12
4.1 Absolute Ratings of TFT LCD Module.............................................................................................12
4.2 Absolute Ratings of Backlight Unit...................................................................................................12
4.3 Absolute Ratings of Environment .....................................................................................................12
5. Electrical characteristics ....................................................... 13
5.1 TFT LCD Module..............................................................................................................................13
5.2 Backlight Unit ...................................................................................................................................15
6. Signal Characteristic ............................................................. 18
6.1 Pixel Format Image ...........................................................................................................................18
6.2 The input data format ........................................................................................................................19
6.3 Signal Description/Pin Assignment...................................................................................................20
6.4 Interface Timing ................................................................................................................................22
6.5 Power ON/OFF Sequence ...............................................................................................................24
www.jxlcd.com
7. Connector Description........................................................... 25
7.1 TFT LCD Module..............................................................................................................................25
8. Dynamic Test ........................................................................ 26
8.1 Vibration Test ....................................................................................................................................26
8.2 Shock Test Spec:................................................................................................................................26
9. Reliability.............................................................................. 27
10. Mechanical Characteristics.................................................. 28
10.1 LCM Outline Dimension.................................................................................................................28
10.2 Screw Hole Depth and Center Position...........................................................................................30
11. Shipping and Package ......................................................... 31
11.1 Shipping Label Format ....................................................................................................................31
11.2 Definition of customer PPID Label and Revision Code..................................................................31
11.3 Carton package................................................................................................................................32
12. Appendix: EDID description ................................................ 33
www.jxlcd.com
AUO NBBU spec. Template 1.0
2 of 36
Page 3
AU OPTRONICS CORPORATION
Product Specification
Record of Revision
Version and Date Page
0.1 2007/10/26 All First Edition for Cus tomer
0.2 2007/10/27 27 No back side drawing Add back side drawing
0.3 2007/11/29 16,
0.4 2007/12/10 17 No LED Driver Pull-up resistor Add LED Driver Pull-up resistor
0.5 2007/12/28 31 1D Label Change to 2D Label
06 2008/1/11 29 orignal position of connector Changed position of connector
07 2008/4/08 33-36 orignal EDID EDID for A00
08 2008/4/30 6 Chromaticity of color is ±0.02 Chromaticity of color
No LED power sequence
30
No 15 years environmentally safety
period mark
Old description New Description Remark
Add LED power sequence
Change Shipping Label Format and
adds 15 years environmentally safety
period mark
modify to
±0.03
www.jxlcd.com
www.jxlcd.com
AUO NBBU spec. Template 1.0
3 of 36
Page 4
AU OPTRONICS CORPORATION
Product Specification
1. Handling Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or
spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard
surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure
human earth when handling.
7) Do not open nor modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) In case if a Module has to be put back into the packing container slot after once it was
taken out from the container, do not press the center of the LED lamp Reflector edge.
Instead, press at the far ends of the LED lamp Reflector edge softly. Otherwise the
TFT Module may be damaged.
10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor
tilt the Interface Connector of the TFT Module.
11) After installation of the TFT Module into an enclosure (Notebook PC Bezel, for
example), do not twist nor bend the TFT Module even momentary. At designing the
enclosure, it should be taken into consideration that no bending/twisting forces are
applied to the TFT Module from outside. Otherwise the TFT Module may be damaged.
12) Small amount of materials having no flammability grade is used in the LCD module. The
LCD module should be supplied by power complied with requirements of Limited Power
Source (IEC60950 or UL1950), or be applied exemption.
13) The LCD module is designed so that the LED in it is supplied by Limited Current Circuit
(IEC60950 or UL1950). Do not connect the LED in Hazardous Voltage Circuit.
www.jxlcd.com
www.jxlcd.com
AUO NBBU spec. Template 1.0
4 of 36
Page 5
AU OPTRONICS CORPORATION
Product Specification
(Note1)
2. General Description
B154PW04 V3 is a Color Active Matrix Liquid Crystal Display composed of a TFT LCD panel, a
driver circuit, and backlight system. The screen format is intended to support the WXGA+
(1440(H) x 900(V)) screen and 262k colors (RGB 6-bits data driver) without backlight inverter.
All input signals are LVDS interface compatible.
B154PW04 V3 is designed for a display unit of notebook style personal computer and industrial
machine.
2.1 General Specification
The following items are characteristics summary on the table at 25 ℃ condition:
Items Unit Specifications
Screen Diagonal [mm] 391 (15.4W”)
Active Area [mm] 331.560 (H) X 207.225 (V)
Pixels H x V 1440x3(RGB) x 900
Pixel Pitch [mm] 0.23025X0.23025
Pixel Format R.G.B. Vertical Stripe
Display Mode Normally White
www.jxlcd.com
White Luminance (I
Note: I
LED
Luminance Uniformity 1.25 max. (5 points)
Contrast Ratio 600 typ
Response Time [ms] 16 typ
Nominal Input Voltage VDD [Volt] +3.3 typ.
Power Consumption [Watt] 5.8 max.
www.jxlcd.com
LED
=19mA)
is lamp current
[cd/m2] 300 typ.(5 points average)
270 min.(5 points average)
1.53 max. (13 points)
Weight [Grams] 460 max.
Physical Size
Electrical Interface Dual channel LVDS
Surface Treatment Glare, Hardness 3H,
AUO NBBU spec. Template 1.0
[mm]
L W T
Max 344.5 222.5 6.1
Typical 344.0 222.0 -
Min 343.5 221.5 -
5 of 36
Page 6
AU OPTRONICS CORPORATION
Product Specification
RoHS Compliance
Support Color 262K colors ( RGB 6-bit )
Temperature Range
Operating
Storage (Non-Operating)
RoHS Compliance
[oC]
[oC]
0 to +50
-25 to +65
2.2 Optical Characteristics
The optical characteristics are measured under stable conditions at 25℃ (Room Temperature) :
Item Unit Conditions Min. Typ. Max. Note
White Luminance
I
LED
=19mA
Viewing Angle
Luminance
Uniformity
Luminance
Uniformity
CR: Contrast Ratio
Cross talk %
Response Time
Chromaticity of color
Coordinates
(CIE 1931)
NTSC %
www.jxlcd.com
www.jxlcd.com
[cd/m2]
[degree]
[degree]
[degree]
[degree]
[msec] Rising
[msec] Falling
[msec] Rising + Falling
5 points average
Horizontal
(Right)
CR = 10 (Left)
Vertical
(Upper)
CR = 10 (Lower)
5 Points
13 Points
500 600 - 6
4 7
Red x
Red y
Green x
Green y
Blue x
Blue y
White x
White y
CIE 1931
270 300 -
55
55
45
45
- - 1.25 1
- - 1.53 2
-
- 12 17
- 16 25
0.570 0.600 0.630
0.315 0.345 0.375
0.290 0.320 0.350
0.525 0.555 0.585
0.120 0.150 0.180
0.090 0.120 0.150
0.283 0.313 0.343
0.299 0.329 0.359
- 45 -
60
60
50
55
4
1, 4, 5.
-
-
8
-
-
8
8
2,8
AUO NBBU spec. Template 1.0
6 of 36
Page 7
AU OPTRONICS CORPORATION
Product Specification
=
Maximum Brightness of thirteen points
Minimum Brightness of thirteen points
Maximum Brightness of five
points
=
Minimum Brightness of five points
Note 1: 5 points position (Ref: Active area)
Note 2: 13 points position (Ref: Active area)
W / 4 W /4 W / 4 W / 4
H /4
H /4
H
H /4
H /4
W /4
1 0
W
1
3
4 5
W
W /4
W /4
2
W /4
1 0
1 0
H /4
www.jxlcd.com
www.jxlcd.com
H /4
H
H /4
H /4
1 0
1
4 5
6
9
1 1
Note 3: The luminance uniformity of 5 or13 points is defined by dividing the maximum luminance values by the
minimum test point luminance
δ
W5
1 2
2
7
1 0
1 3
3
8
δ
Note 4: Measurement method
AUO NBBU spec. Template 1.0
W13
7 of 36
Page 8
AU OPTRONICS CORPORATION
Product Specification
Field=2
°
Contrast ratio (CR)=
Brightness on the “W hite” state
Brightness on the “Black” state
The LCD module should be stabilized at given temperature for 30 minutes to avoid abrupt temperature change
during measuring. In order to stabilize the luminance, the measurement should be executed after lighting Backlight
for 30 minutes in a stable, windless and dark room.
Note 5： Definition of Average Luminance of White (YL):
Measure the luminance of gray level 63 at 5 points，Y
L (x) is corresponding to the luminance of the point X at Figure in Note (1).
Note 6： Definition of contrast ratio:
Note 7： Definition of Cross Talk (CT)
CT = | YB – YA | / YA × 100 (%)
Where
YA = Luminance of measured location without gray level 0 pattern (cd/m2)
www.jxlcd.com
www.jxlcd.com
= [L (1)+ L (2)+ L (3)+ L (4)+ L (5)] / 5
L
Contrast ratio is calculated with the following formula.
Photo detector
AUO NBBU spec. Template 1.0
8 of 36
Page 9
AU OPTRONICS CORPORATION
Product Specification
YB = Luminance of measured location with gray level 0 pattern (cd/m2)
Note 8: Definition of response time:
The output signals of BM-7 or equivalent are measured when the input signals are changed from “Black” to
“White” (falling time) and from “White” to “Black” (rising time), respectively. The response time interval between the
10% and 90% of amplitudes. Refer to figure as below.
"Black"
100%
S
i
90%
g
n
a
l
(
R
e
l
a
t
i
v
e
v
a
l
u
e
)
www.jxlcd.com
www.jxlcd.com
10%
0%
Tr
Tf
"White""White"
AUO NBBU spec. Template 1.0
9 of 36
Page 10
AU OPTRONICS CORPORATION
Product Specification
Note 8. Definition of viewing angle
Viewing angle is the measurement of contrast ratio ≧10, at the screen center, over a 180° horizontal and
180° vertical range (off-normal viewing angles). The 180° viewing angle range is broken down as follows; 90° (θ)
horizontal left and right and 90° (Φ) vertical, high (up) and low (down). The measurement direction is typically
perpendicular to the display surface with the screen rotated about its center to develop the desired measurement
viewing angle.
www.jxlcd.com
www.jxlcd.com
AUO NBBU spec. Template 1.0
10 of 36
Page 11
AU OPTRONICS CORPORATION
Product Specification
X
Od d
xIN0
LCD C on necto r(
50
pin)
3. Functional Block Diagram
The following diagram shows the functional block of the 15.4 inches wide Color TFT/LCD Module:
(8 pai rs LV DS )
Od dxIN 1
Od dxIN 2
Od dxC LKIN
Ev enxIN0
Ev enxIN1
Ev enxIN2
Ev enxCL KIN
LC D D RIVE
BO ARD
LC D
Co ntr olle r
Back light U nit
TFT ARRAY/C ELL
1440(R/G/B) x 3 x 900
LE D
Po wer
Co ntro l Sig nal
VD D
GN D
JA E FI-VHP50S-A-HF11
Mating Ho using JAE FI-VHP50C-A
www.jxlcd.com
www.jxlcd.com
DC -DC
Co nve rte r
Re f circu it
Y-D river
-D rive r
AUO NBBU spec. Template 1.0
11 of 36
Page 12
AU OPTRONICS CORPORATION
Product Specification
4. Absolute Maximum Ratings
An absolute maximum rating of the module is as following:
4.1 Absolute Ratings of TFT LCD Module
Item Symbol Min Max Unit Conditions
Logic/LCD Drive Voltage
Vin -0.3 +4.0 [Volt] Note 1,2
4.2 Absolute Ratings of Backlight Unit
Item Symbol Min Max Unit Conditions
LED Current ILED - 20 [mA] rms Note 1,2
4.3 Absolute Ratings of Environment
Item Symbol Min Max Unit Conditions
Operating Temperature
Operation Humidity HOP 5 95 [%RH] Note 3
Storage Temperature
Storage Humidity HST
Note 1: At Ta (25℃ )
Note 2: Permanent damage to the device may occur if exceed maximum values
Note 3: For quality performance, please refer to AUO IIS (Incoming Inspection Standard).
TOP 0 +50 [oC] Note 3
TST -20 +60 [oC] Note 3
5 95
[%RH]
Note 3
Twb=39°C
www.jxlcd.com
www.jxlcd.com
Operating Range
AUO NBBU spec. Template 1.0
Storage Range
12 of 36
Page 13
AU OPTRONICS CORPORATION
Product Specification
-
90%
10%
5. Electrical characteristics
5.1 TFT LCD Module
5.1.1 Power Specification
Input power specifications are as follows;
Symble Parameter Min Typ Max Units
VDD Logic/LCD Drive
PDD VDD Power
IDD IDD Current
I
Rush
Inrush Current
VDDrp Allowable
Logic/LCD Drive
3.0 3.3 3.6 [Volt]
- 2 [Watt] Note 1/2
- 380
- -
- -
562
2000 [mA]
100 [mV]
Ripple Voltage
Note 1 : Maximum Measurement Condition：Black Pattern
Note 2：Typical Measurement Condition: Mosaic Pattern
Note 3：Measure Condition
+5.0V
+12.0V
R1
47K
R2
1K
VR1
47K
www.jxlcd.com
www.jxlcd.com
(High to Low)
Control
Signal
SW1
SW MAG-SPST
1 2
D6
D5
D2 S
D1
G
C3
0.01uF/25V
Q3
AO6402
D2SD1D5
G
D6
Q3
AO6402
F1
[mA]
p-p
Note 1/2
Note 3
(LCD Module Input)
C1
1uF/16V
Note
VCC
C2
1uF/25V
3.3V
0V
0.5ms
Vin rising time
AUO NBBU spec. Template 1.0
13 of 36
Page 14
AU OPTRONICS CORPORATION
Product Specification
VSS
5.1.2 Signal Electrical Characteristics
Input signals shall be low or High-impedance state when VDD is off.
It is recommended to refer the specifications of THC63LVDF84A (Thine Electronics Inc.) in
detail.
Signal electrical characteristics are as follows;
Parameter
Vth
Vtl
Condition Min Max Unit
Differential Input High
Threshold (Vcm=+1.2V)
Differential Input Low
Threshold (Vcm=+1.2V)
-
-100
100
-
[mV]
[mV]
Vcm
Note: LVDS Signal Waveform
V
t
Differential Input
Common Mode Voltage
www.jxlcd.com
www.jxlcd.com
Vcm
1.1
1.45
[V]
AUO NBBU spec. Template 1.0
14 of 36
Page 15
AU OPTRONICS CORPORATION
Product Specification
5.2 Backlight Unit
The BLU system is an edge type light source with LED (Light Emitting Diode) light bar
Item Symbol Min Typ Max Units Condition
Fixed input current ILt 20 [mA] rms
Light bar Voltage
Light bar Power
Light bar PIN assignment:
www.jxlcd.com
PIN NO. Pin assignment Function
1 VOUT LED Anode (Positive)
2 VOUT LED Anode (Positive)
3 VOUT LED Anode (Positive)
4 NC NC
5 FB6 LED Cathode (Negative)
6 FB5 LED Cathode (Negative)
7 FB4 LED Cathode (Negative)
8 FB3 LED Cathode (Negative)
9 FB2 LED Cathode (Negative)
10 FB1 LED Cathode (Negative)
www.jxlcd.com
VL 32. 34
PL 3.7 3.88
[Volt] rms
Wt
AUO NBBU spec. Template 1.0
15 of 36
Page 16
AU OPTRONICS CORPORATION
Product Specification
LED Power Sequence
Note: The duty of LED dimming signal should be more than 20% in T2..
Valus
Symbol
T1 10 --- --- ms
T2 100 --- --- ms
www.jxlcd.com
www.jxlcd.com
T3 10 --- --- ms
Min Typ Max
Unit
AUO NBBU spec. Template 1.0
16 of 36
Page 17
AU OPTRONICS CORPORATION
Product Specification
LED Driver SMBUS Pull-up resistor
www.jxlcd.com
www.jxlcd.com
SMBUS Pull-up Circuitry
Setting value for Pull-up resistor Rp
−≥≥− VDDRpVDD
Suggestion: IF VDD=3.3V, Rp=10K ohm; IF VDD=5V, Rp=15K ohm
Note: Rp is the equivalent resistor for SMBUS Pull-up Circuitry
AUO NBBU spec. Template 1.0
66 −−
)10*350/()4.0()10*100/()4.0(
17 of 36
Page 18
AU OPTRONICS CORPORATION
Product Specification
6. Signal Characteristic
6.1 Pixel Format Image
Following figure shows the relationship of the input signals and LCD pixel format.
www.jxlcd.com
www.jxlcd.com
AUO NBBU spec. Template 1.0
18 of 36
Page 19
AU OPTRONICS CORPORATION
Product Specification
6.2 The input data format
Signal Name
VEEDID (3.3V) +3.3V EDID Power
CLK EEDID EDID Clock Input
DATA EEDID EDID Data Input
ORXIN0-, ORXIN0+
ORXIN1-, ORXIN1+
ORXIN2-, ORXIN2+
ORXCLKIN-, ORXCLKIN+ Odd LVDS differential clock input
ERXIN0-, ERXIN0+
ERXIN1-, ERXIN1+
ERXIN2-, ERXIN2+
ERXCLKIN-, ERXCLKIN+ Even LVDS differential clock input
VDD
VSS
Note: Output signals from any system shall be low or High-impedance state when VDD is off.
www.jxlcd.com
www.jxlcd.com
Odd LVDS differential data input(ORed0-ORed5, OGreen0)
Odd LVDS differential data input(OGreen1-OGreen5, OBlue0-OBlue1)
Odd LVDS differential data input(OBlue2-OBlue5, Hsync, Vsync, DE)
Even LVDS differential data input(ERed0-ERed5, EGreen0)
Even LVDS differential data input(EGreen1-EGreen5, EBlue0-EBlue1)
Even LVDS differential data input(EBlue2-EBlue5)
+3.3V Power Supply
Ground
Description
AUO NBBU spec. Template 1.0
19 of 36
Page 20
AU OPTRONICS CORPORATION
Product Specification
6.3 Signal Description/Pin Assignment
LVDS is a differential signal technology for LCD interface and high speed data transfer device.
PIN# Signal Name Description
1 Test Loop (only to pin 30) Diag. pin for test
2 VEEDID (3.3v) DDC 3.3Vpower
3 VSS Ground
4 CLK EEDID DDC Clock
5 DATA EEDID DDC Data
6 VSS Ground
7 Odd_Rin0- Odd channel Differential Data Input
8 Odd_Rin0+ Odd channel Differential Data Input
9 VSS Ground
10 Odd_Rin1- Odd channel Differential Data Input
11 Odd_Rin1+ Odd channel Differential Data Input
12 VSS Ground
13 Odd_Rin2- Odd channel Differential Data Input
14 Odd_Rin2+ Odd channel Differential Data Input
15 VSS Ground
16 Odd_ClkIN-
17 Odd_ClkIN+ Odd channel Differential Clock Input
18 VSS Ground
19 Even_Rin0- Even channel Differential Data Input
20 Even_Rin0+ Even channel Differential Data Input
21 VSS Ground
22 Even_Rin1- Even channel Differential Data Input
23 Even_Rin1+ Even channel Differential Data Input
24 VSS Ground
25 Even_Rin2- Even channel Differential Data Input
26 Even_Rin2+ Even channel Differential Data Input
27 VSS Ground
28 Even_ClkIN- Even channel Differential Clock Input
29 Even_ClkIN+ Even channel Differential Clock Input
30 Test Loop (only to pin 1) Diag. pin for test
31 Test Loop (only to pin 50) Diag. pin for test
32 VDD Power Supply (+3.3V)
33 VDD Power Supply (+3.3V)
www.jxlcd.com
www.jxlcd.com
Odd channel Differential Clock Input
AUO NBBU spec. Template 1.0
20 of 36
Page 21
AU OPTRONICS CORPORATION
Product Specification
34 TEST (BIST_EN) BIST Function
35 +5V_ALW Power Supply (+5V)
36 VSS Ground
37 VSS Ground
38 PWM_BL Systwm side PWM input signal for brightness control
39 VBL- LED Power Ground
40 VBL- LED Power Ground
41 VBL- LED Power Ground
42 VBL- LED Power Ground
43 NC No Connection
44 VBL+ Backlight Input Voltage
45 VBL+ Backlight Input Voltage
46 VBL+ Backlight Input Voltage
47 VBL+ Backlight Input Voltage
48 SMB_DATA SMBus interface for sending brightness information
49 SMB_CLK SMBus interface for sending brightness information
50 Test Loop (only to pin 31) Diag. pin for test
Note1: Start from right side
www.jxlcd.com
www.jxlcd.com
AUO NBBU spec. Template 1.0
21 of 36
Page 22
AU OPTRONICS CORPORATION
Product Specification
6.4 Interface Timing
6.4.1 Timing Characteristics
Basically, interface timings should match the 1440x900 /60Hz manufacturing guide line timing.
Parameter Symbol Min. Typ. Max. Unit
Frame Rate - 50 60 - Hz
Clock frequency 1/ T
Vertical
Section
Horizontal
Section
Note : DE mode only
Period TV 904 912 2048
Active TVD 900 900 900
Blanking TVB 4 12 -
Period TH 760 880 1024
Active THD 720 720 720
Blanking THB 40 160 -
- 48.2 60.2 MHz
Clock
T
Line
T
Clock
www.jxlcd.com
www.jxlcd.com
AUO NBBU spec. Template 1.0
22 of 36
Page 23
AU OPTRONICS CORPORATION
6.4.2 Timing diagram
Product Specification
AUO NBBU spec. Template 1.0
www.jxlcd.com
www.jxlcd.com
23 of 36
Page 24
AU OPTRONICS CORPORATION
Product Specification
T3 T2
T1
T7
6.5 Power ON/OFF Sequence
VDD power and lamp on/off sequence is as follows. Interface signals are also shown in the chart.
Signals from any system shall be Hi-Z state or low level when VDD is off.
Power Supply VDD
Backlight On
www.jxlcd.com
www.jxlcd.com
90%
10%
Power Sequence Timing
Parameter
T1
T2
T3
T4
T5
T6
T7
Min.
0.5
5
0.5
400
200
200
0
T5
Value
Typ.
-
-
-
-
-
-
-
VALID
DATA
Max.
10
50
50
-
-
-
10
90%
10%
T4
T6
Units
(ms)
(ms)
(ms)
(ms)
(ms)
(ms)
(ms)
AUO NBBU spec. Template 1.0
24 of 36
Page 25
AU OPTRONICS CORPORATION
Product Specification
7. Connector Description
Physical interface is described as for the connector on module.
These connectors are capable of accommodating the following signals and will be following
components.
7.1 TFT LCD Module
Connector Name / Designation For Signal Connector
Manufacturer JAE or compatible
Type / Part Number
Mating Housing/Part Number
www.jxlcd.com
www.jxlcd.com
JAE FI-VHP50S-A-HF11
JAE FI-VHP50C-A
or compatible
or compatible
AUO NBBU spec. Template 1.0
25 of 36
Page 26
AU OPTRONICS CORPORATION
Product Specification
8. Dynamic Test
8.1 Vibration Test
Test condition:
Acceleration: 1.5 G
Frequency: 10 - 500Hz Random
Sweep: 30 Minutes each Axis (X, Y, Z)
8.2 Shock Test Spec:
Test condition:
Acceleration: 220 G , Half sine wave
Active time: 2 ms
Pulse: +/-X,+/-Y,+/-Z , one time for each side
Remark:
1. Ambient condition is
2.
Non-packaged and Non-operation
25 + 5℃, Relative humidity : 40% ~ 70%
www.jxlcd.com
www.jxlcd.com
AUO NBBU spec. Template 1.0
26 of 36
Page 27
AU OPTRONICS CORPORATION
9. Reliability
Items
Temperature
Humidity Bias
Product Specification
Required Condition Note
Ta= 40
℃℃℃℃
, 95%RH, 300h
High Temperature
Operation
Low Temperature
Operation
High Temperature
Storage
Low Temperature
Storage
Thermal Shock
Test
ESD
Note1: According to EN 61000-4-2 , ESD class B: Some performance degradation allowed. No data lost
. Self-recoverable. No hardware failures.
Remark: MTBF (Excluding the LED): 30,000 hours with a confidence level 90%
www.jxlcd.com
www.jxlcd.com
Ta= 50
℃℃℃℃
, Dry, 300h
Ta= 0
℃℃℃℃
, 300h
Ta= 65
℃℃℃℃
, 35%RH, 300h
Ta= -25
Ta=-40
Contact : ±8 KV
Air : ±15 KV
℃℃℃℃
, 50%RH, 300h
℃℃℃℃
to 65
℃℃℃℃
, Duration at 30 min, 100 cycles
Note 1
AUO NBBU spec. Template 1.0
27 of 36
Page 28
AU OPTRONICS CORPORATION
Product Specification
AUO
Must paste the
10. Mechanical Characteristics
10.1 LCM Outline Dimension
www.jxlcd.com
www.jxlcd.com
註解
註解
[BY1]:
註解註解
Get from RD-
PDF format.
NBBU spec. Template 1.0
28 of 36
Page 29
AU OPTRONICS CORPORATION
Product Specification
AUO
www.jxlcd.com
www.jxlcd.com
NBBU spec. Template 1.0
29 of 36
Page 30
AU OPTRONICS CORPORATION
Product Specification
10.2 Screw Hole Depth and Center Position
Screw hole minimum depth, from side surface = 2.3 mm (Ref. drawing)
Screw hole center location, from front surface = 3.7 ± 0.2mm (Ref. drawing)
Screw Torque: Maximum 2.5 kgf-cm
www.jxlcd.com
www.jxlcd.com
AUO NBBU spec. Template 1.0
30 of 36
Page 31
AU OPTRONICS CORPORATION
932-0123-A00
11. Shipping and Package
Product Specification
11.1 Shipping Label Format
Manufactured 08/02
Model No: B154PW04 V3
AU Optronics
Made In
CN
DP/N
0HW663
CN -0HW663-72090-
MADE IN CHINA (S1)
H/W: 3A F/W:1
3AXXG
11.2 Definition of customer PPID Label and Revision Code
Please refer to the Dell Part identification Label Specification, Number:13190
Buil d Name(s ): PPID Revision Code(s):
Sub System Test (SST)
Working Sample (WS)
ENG 2
Product Test (PT)
Engineering Sample (ES)
ENG 3
System Test (ST)
Customer Sample (CS)
ENG 4
X-Build (XB)
Mass Production (MP)
ENG 5
www.jxlcd.com
www.jxlcd.com
X00, X01, X02, …, X0n
X10, X11, X12, …, X1n
X20, X21, X22, … X2n
A00, A01, A02, … A0n
AUO NBBU spec. Template 1.0
31 of 36
Page 32
AU OPTRONICS CORPORATION
Product Specification
11.3 Carton package
The outside dimension of carton is 455 (L)mm x 380 (W)mm x 355 (H)mm
11.3 Shipping package of palletizing sequence
www.jxlcd.com
www.jxlcd.com
AUO NBBU spec. Template 1.0
32 of 36
Page 33
AU OPTRONICS CORPORATION
Product Specification
Value
(DEC)
12. Appendix: EDID description
Byte Value
(hex)
0 Header
1 Header
2 Header
3 Header
4 Header
5 Header
6 Header
7 Header
8 EISA manufacture code = 3 Character ID
9 EISA manufacture code (Compressed ASCII)
0A Panel Supplier Reserved – Product Code
0B Panel Supplier Reserved – Product Code
0C LCD module Serial No - Preferred but Optional (“0” if not used)
0D LCD module Serial No - Preferred but Optional (“0” if not used)
0E LCD module Serial No - Preferred but Optional (“0” if not used)
0F LCD module Serial No - Preferred but Optional (“0” if not used)
10 Week of manufacture
11 Year of manufacture
12 EDID structure version # = 1
13 EDID revision # = 3
14 Video I/P definition = Digital I/P (80h)
15 Max H image size = (Rounded to cm)
16 Max V image size = (Rounded to cm)
Display gamma = (gamma ×100)-100 = Example: ( 2.2×100 ) –
17
100 = 120
18 Feature support ( no DPMS, Active off, RGB, timing BLK 1)
19 Red/Green Low bit (RxRy/GxGy)
1A Blue/White Low bit (BxBy/WxWy)
1B Red X Rx = 0.6
1C Red Y Ry = 0.345
1D Green X Gx = 0.32
1E Green Y Gy = 0.555
1F Blue X Bx = 0.15
20 Blue Y By = 0.12
21 White X Wx = 0.313
22 White Y Wy = 0.329
AUO NBBU spec. Template 1.0
www.jxlcd.com
www.jxlcd.com
Field Name and Comments
(hex)
00
FF
FF
FF
FF
FF
FF
00
06
AF
77
43
00
00
00
00
01
11
01
03
90
21
15
78
0A
90
B5
99
58
52
8E
26
1E
50
54
Value
(binary)
00000000
11111111
11111111
11111111
11111111
11111111
11111111
00000000
00000110
10101111
01110111
01000011
00000000
00000000
00000000
00000000
00000001
00010001
00000001
00000011
10010000
00100001
00010101
01111000
00001010
10010000
10110101
10011001
01011000
01010010
10001110
00100110
00011110
01010000
01010100
33 of 36
Page 34
AU OPTRONICS CORPORATION
Product Specification
23 Established timings 1 (00h if not used)
24 Established timings 2 (00h if not used)
25 Manufacturer’s timings (00h if not used)
26 Standard timing ID1 (01h if not used)
27 Standard timing ID1 (01h if not used)
28 Standard timing ID2 (01h if not used)
29 Standard timing ID2 (01h if not used)
2A Standard timing ID3 (01h if not used)
2B Standard timing ID3 (01h if not used)
2C Standard timing ID4 (01h if not used)
2D Standard timing ID4 (01h if not used)
2E Standard timing ID5 (01h if not used)
2F Standard timing ID5 (01h if not used)
30 Standard timing ID6 (01h if not used)
31 Standard timing ID6 (01h if not used)
32 Standard timing ID7 (01h if not used)
33 Standard timing ID7 (01h if not used)
34 Standard timing ID8 (01h if not used)
35 Standard timing ID8 (01h if not used)
36 Pixel Clock/10,000 = 96310000 /10000 (LSB)
37 Pixel Clock/10,000 = 96310000 /10000 (MSB)
Horizontal Active = 1440 pixels
38
(lower 8 bits)
39 Horizontal Blanking (Thbp) = 320 pixels (lower 8 bits)
3A Horizontal Active/Horizontal blanking (Thbp) (upper4:4 bits)
3B Vertical Active = 900 lines
Vertical Blanking (Tvbp) = 12 lines (DE Blanking typ. for DE only
3C
panels)
Vertical Active : Vertical Blanking (Tvbp) (upper4:4
3D
bits)
3E Horizontal Sync, Offset (Thfp) = 64 pixels
3F Horizontal Sync, Pulse Width = 32 pixels
40 Vertical Sync, Offset (Tvfp) = 3 lines Sync Width = 3 lines
41 Horizontal Vertical Sync Offset/Width upper 2 bits
42 Horizontal Image Size = 331.2 mm
43 Vertical image Size = 207 mm
44 Horizontal Image Size / Vertical image size
45 Horizontal Border = 0 (Zero for Notebook LCD)
46 Vertical Border = 0 (Zero for Notebook LCD)
if display uses standard blanking (HSyncPolarity = POS,
47
VSyncPolarity = NEG) , for DVD compliance.
www.jxlcd.com
www.jxlcd.com
00
00
00
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
32
2A
A0
16
52
84
0C
30
40
20
33
00
4B
CF
10
00
00
1A
00000000
00000000
00000000
00000001
00000001
00000001
00000001
00000001
00000001
00000001
00000001
00000001
00000001
00000001
00000001
00000001
00000001
00000001
00000001
00110010
00101010
10100000
00010110
01010010
10000100
00001100
00110000
01000000
00100000
00110011
00000000
01001011
11001111
00010000
00000000
00000000
00011010
AUO NBBU spec. Template 1.0
34 of 36
Page 35
AU OPTRONICS CORPORATION
Product Specification
Manufacturer P/N (If <13 char, then terminate with ASCII code 0Ah,
48 Pixel Clock/10,000 = 96310000 /10000 (LSB)
49 Pixel Clock/10,000 = 96310000 /10000 (MSB)
Horizontal Active = 1440 pixels
4A
(lower 8 bits)
4B Horizontal Blanking (Thbp) = 320 pixels (lower 8 bits)
4C Horizontal Active/Horizontal blanking (Thbp) (upper4:4 bits)
4D Vertical Active = 900 lines
Vertical Blanking (Tvbp) = 12 lines (DE Blanking typ. for DE only
4E
panels)
Vertical Active : Vertical Blanking (Tvbp) (upper4:4
4F
bits)
50 Horizontal Sync, Offset (Thfp) = 64 pixels
51 Horizontal Sync, Pulse Width = 32 pixels
52 Vertical Sync, Offset (Tvfp) = 3 lines Sync Width = 3 lines
53 Horizontal Vertical Sync Offset/Width upper 2 bits
54 Horizontal Image Size = 331.2 mm
55 Vertical image Size = 207 mm
56 Horizontal Image Size / Vertical image size
57 Horizontal Border = 0 (Zero for Notebook LCD)
58 Vertical Border = 0 (Zero for Notebook LCD)
if display uses standard blanking (HSyncPolarity = POS,
59
VSyncPolarity = NEG) , for DVD compliance.
5A Flag
5B Flag
5C Flag
5D Dummy Descriptor
5E Flag
5F Dell P/N 1st Character
60 Dell P/N 2nd Character
61 Dell P/N 3rd Character
62 Dell P/N 4th Character
63 Dell P/N 5th Character
64 EEDID Revision = A00 (X Build and MP)
65 Manufacturer P/N
66 Manufacturer P/N
67 Manufacturer P/N
68 Manufacturer P/N
69 Manufacturer P/N
6A Manufacturer P/N
www.jxlcd.com
www.jxlcd.com
32
2A
A0
16
52
84
0C
30
40
20
33
00
4B
CF
10
00
00
1A
00
00
00
FE
00
48
57
36
36
33
80
42
31
35
34
50
57
00110010
00101010
10100000
00010110
01010010
10000100
00001100
00110000
01000000
00100000
00110011
00000000
01001011
11001111
00010000
00000000
00000000
00011010
00000000
00000000
00000000
11111110
00000000
01001000
01010111
00110110
00110110
00110011
10000000
01000010
00110001
00110101
00110100
01010000
01010111
6B
set remaining char = 20h)
6C Flag
AUO NBBU spec. Template 1.0
34
00
00110100
00000000
35 of 36
Page 36
AU OPTRONICS CORPORATION
Product Specification
6D Flag
6E Flag
6F Data Type Tag:
70 Flag
71 SMBUS Value = XX nits
72 SMBUS Value = XX nits
73 SMBUS Value = XX nits
74 SMBUS Value = XX nits
75 SMBUS Value = XX nits
76 SMBUS Value = XXX nits
77 SMBUS Value = XXX nits
78 SMBUS Value = max nits (Typically = 00h, XXX nits)
Bit[1:0] 00: reserved, 01: single LVDS, 10: dual LVDS, 11:
reserved
Bit[2] 0: No RTC support, 1: RTC support
79
Bit[7:3] Reserved
Bit[0] 0: No BIST support, 1: BIST support
Bit[7:1] Reserved
7A
(If <13 char, then terminate with ASCII code 0Ah, set remaining
7B
char = 20h)
(If <13 char, then terminate with ASCII code 0Ah, set remaining
7C
char = 20h)
(If <13 char, then terminate with ASCII code 0Ah, set remaining
7D
char = 20h)
00
00
00
00
00
00
00
00
00
00
00
00
02
01
0A
20
20
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000010
00000001
00001010
00100000
00100000
Extension flag (# of optional 128 EDID extension blocks to follow,
7E
Typ = 0)
Checksum (The 1-byte sum of all 128 bytes in this EDID block
7F
shall = 0)
AUO NBBU spec. Template 1.0
www.jxlcd.com
www.jxlcd.com
00
75
00000000
01110101
36 of 36
Loading...