) Preliminary Specifications
(V
( ) Final Specifications
Product Specification
AU OPTRONICS CORPORATION
Module
Model Name
15.4” WXGA Color TFT-LCD
B154EW08 V1(HW 0A)
Customer Date
www.jxlcd.com
www.jxlcd.com
Checked &
Approved by
Approved by Date
Jerry Chen
Prepared by
2007/01/04
Note: This Specification is subject to change without
notice.
document version 0.1 1/36
CH Lin 2007/01/04
MDBU Marketing Division /
AU Optronics corporation
Product Specification
AU OPTRONICS CORPORATION
Contents
1. Handling Precautions.......................................................................................4
2. General Description..........................................................................................4
2.1 Display Characteristics.......................................................................................................5
2.2 Optical Characteristics.......................................................................................................6
3. Functional Block Diagram..............................................................................11
4. Absolute Maximum Ratings...........................................................................12
4.1 TFT LCD Module..............................................................................................................12
4.2 Backlight Unit...................................................................................................................12
4.3 Absolute Ratings of Environment.....................................................................................12
5. Electrical characteristics................................................................................13
5.1 TFT LCD Module..............................................................................................................13
5.2 Backlight Unit...................................................................................................................15
6. Signal Characteristic......................................................................................17
6.1 Pixel Format Image..........................................................................................................17
6.2 The input data format.......................................................................................................18
6.3 Signal Description............................................................................................................19
6.4 Interface Timing...............................................................................................................22
6.5 Power ON/OFF Sequence...............................................................................................24
7. Connector & Pin Assignment.........................................................................25
7.1 TFT LCD Module..............................................................................................................25
7.2 Backlight Unit...................................................................................................................25
7.3 Signal for Lamp connector...............................................................................................25
8. Vibration and Shock Test...............................................................................26
8.1 Vibration Test...................................................................................................................26
8.2 Shock Test Spec:..............................................................................................................26
9. Reliability.........................................................................................................27
10. Mechanical Characteristics..........................................................................28
10.1 LCM Outline Dimension.................................................................................................28
10.2 Screw Hole Depth and Center Position..........................................................................30
11. Shipping and Package..................................................................................31
www.jxlcd.com
www.jxlcd.com
11.1 Shipping Label Format...................................................................................................31
11.2. Carton package.............................................................................................................32
11.3 Shipping package of palletizing sequence.....................................................................32
12. Appendix: EDID description.........................................................................33
document version 0.1 2/36
Product Specification
AU OPTRONICS CORPORATION
Record of Revision
Version and Date Page
0.1 2007/01/04 All First Edition for Customer
www.jxlcd.com
www.jxlcd.com
Old description New Description Remark
document version 0.1 3/36
Product Specification
1. Handling Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or
spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard
surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure
human earth when handling.
7) Do not open nor modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) In case if a Module has to be put back into the packing container slot after once it was
taken out from the container, do not press the center of the CCFL Reflector edge.
AU OPTRONICS CORPORATION
Instead, press at the far ends of the CFL Reflector edge softly. Otherwise the TFT
Module may be damaged.
10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor
tilt the Interface Connector of the TFT Module.
11) After installation of the TFT Module into an enclosure (Notebook PC Bezel, for
example), do not twist nor bend the TFT Module even momentary. At designing the
enclosure, it should be taken into consideration that no bending/twisting forces are
applied to the TFT Module from outside. Otherwise the TFT Module may be
damaged.
12) Cold cathode fluorescent lamp in LCD contains a small amount of mercury. Please follow
local ordinances or regulations for disposal.
13) Small amount of materials having no flammability grade is used in the LCD module. The
LCD module should be supplied by power complied with requirements of Limited Power
Source(, IEC60950 or UL1950), or be applied exemption.
14) The LCD module is designed so that the CCFL in it is supplied by Limited Current
Circuit(IEC60950 or UL1950). Do not connect the CCFL in Hazardous Voltage Circuit.
www.jxlcd.com
www.jxlcd.com
2. General Description
B154EW08 V1 is a Color Active Matrix Liquid Crystal Display composed of a TFT LCD panel, a
driver circuit, and backlight system. The screen format is intended to support the WXGA
(1280(H) x 800(V)) screen and 262k colors (RGB 6-bits data driver). All input signals are LVDS
interface compatible. Inverter of backlight is not included.
document version 0.1 4/36
Product Specification
(
Note1
)
550 max.
RoHS Compliance
B154EW08 V1 is designed for a display unit of notebook style personal computer and industrial
machine.
2.1 General Specification
The following items are characteristics summary on the table at 25 ℃ condition:
Items Unit Specifications
Screen Diagonal [mm] 391 (15.4W”)
Active Area [mm] 331.2 X 207.0
Pixels H x V 1280x3(RGB) x 800
Pixel Pitch [mm] 0.2588X0.2588
Pixel Arrangement R.G.B. Vertical Stripe
Display Mode Normally White
AU OPTRONICS CORPORATION
White Luminance (ICCFL=6.0mA)
Note: ICCFL is lamp current
Luminance Uniformity 1.25 max. (5 points)
Contrast Ratio 400 typ
www.jxlcd.com
Optical Rise Time/Fall Time [msec] 6/2 typ.
Nominal Input Voltage VDD [Volt] +3.3 typ.
Power Consumption [Watt] 6.0 max.(without inverter)
Weight [Grams] 525 typ.
Physical Size [mm] 344.0 typ. x 222.0 typ. x 6.1 max.
Electrical Interface 1 channel LVDS
Surface Treatment Glare, Hardness 3H,
Support Color 262K colors ( RGB 6-bit )
Temperature Range
Operating
Storage (Non-Operating)
RoHS Compliance
www.jxlcd.com
[cd/m2] 200 typ. (5 points average)
170 min. (5 points average)
300 min.
Reflectance 4.3%
[oC]
[oC]
0 to +50
-20 to +60
document version 0.1 5/36
Product Specification
2.2 Optical Characteristics
The optical characteristics are measured under stable conditions at 25℃ (Room Temperature) :
Item Unit Conditions Min. Typ. Max. Note
AU OPTRONICS CORPORATION
White Luminance
ICCFL=6.0mA
Viewing Angle
Luminance Uniformity
Luminance Uniformity
CR: Contrast Ratio
Cross talk %
Response Time
Color / Chromaticity
Coordinates
(CIE 1931)
www.jxlcd.com
www.jxlcd.com
[cd/m2] 5 points average
[degree]
[degree]
[degree]
[degree]
[msec] Rising
[msec] Falling
[msec] Rising + Falling
Horizontal (Right)
CR = 10 (Left)
Vertical (Upper)
CR = 10 (Lower)
5 Points
13 Points
300 400 - 6
4 7
Red x
Red y
Green x
Green y
Blue x
Blue y
White x
White y
170 200 - 1, 4, 5.
-
-
-
-
1.25 1
1.50 2
-
- 2 5
8 15
0.560 0.590 0.620
0.315 0.345 0.375
0.285 0.315 0.345
0.520 0.555 0.585
0.125 0.155 0.185
0.125 0.155 0.185
0.283 0.313 0.343
0.299 0.329 0.359
45
45
15
35
6
-
-
-
-
10
8
8
2,8
document version 0.1 6/36
Product Specification
= Maximum Brightness of thirteen points
Minimum Brightness of thirteen points
Maximum Brightness of five
points
= Minimum Brightness of five
points
Note 1: 5 points position (Display area : 331.2mm x 207.0mm)
H/4
H/4
AU OPTRONICS CORPORATION
W
W/4 W/4 W/4 W/4
12
H
Note 2: 13 points position
www.jxlcd.com
www.jxlcd.com
H/4
H/4
H
H/4
H/4
H/4
10
3
4
W/4
10
1
6
W/4
45
W
5
W/4
2
7
W/4
10
3
8
H/4
10
Note 3: The luminance uniformity of 5 and 13 points is defined by dividing the maximum luminance values by the
minimum test point luminance
δ
W5
δ
Note 4: Measurement method
document version 0.1 7/36
W13
11
9
12
10
13
Product Specification
Field=2
°
Contrast ratio (CR)=
Brightness on the “White” state
Brightness on the “Black” state
The LCD module should be stabilized at given temperature for 30 minutes to avoid abrupt temperature change
during measuring. In order to stabilize the luminance, the measurement should be executed after lighting Backlight
for 30 minutes in a stable, windless and dark room.
AU OPTRONICS CORPORATION
Photo detector
www.jxlcd.com
Note 5： Definition of Average Luminance of White (YL):
Measure the luminance of gray level 63 at 5 points，Y
L (x) is corresponding to the luminance of the point X at Figure in Note (1).
Note 6： Definition of contrast ratio:
Note 7： Definition of Cross Talk (CT)
www.jxlcd.com
= [L (1)+ L (2)+ L (3)+ L (4)+ L (5)] / 5
L
Contrast ratio is calculated with the following formula.
CT = | YB – YA | / YA × 100 (%)
Where
YA = Luminance of measured location without gray level 0 pattern (cd/m2)
document version 0.1 8/36
Product Specification
YB = Luminance of measured location with gray level 0 pattern (cd/m2)
Note 8: Definition of response time:
The output signals of BM-7 or equivalent are measured when the input signals are changed from “Black” to
“White” (falling time) and from “White” to “Black” (rising time), respectively. The response time interval between the
10% and 90% of amplitudes. Refer to figure as below.
AU OPTRONICS CORPORATION
"Black"
100%
S
i
90%
g
n
a
l
(
R
e
l
a
t
i
v
e
v
a
l
u
e
)
www.jxlcd.com
www.jxlcd.com
10%
0%
Tr
Tf
"White""White"
document version 0.1 9/36
Product Specification
Note 8. Definition of viewing angle
Viewing angle is the measurement of contrast ratio ≧10, at the screen center, over a 180° horizontal and
180° vertical range (off-normal viewing angles). The 180 ° viewing angle range is broken down as follows; 90 ° (θ)
horizontal left and right and 90° (Φ) vertical, high (up) and low (down). The measurement direction is typically
perpendicular to the display surface with the screen rotated about its center to develop the desired measurement
viewing angle.
AU OPTRONICS CORPORATION
www.jxlcd.com
www.jxlcd.com
document version 0.1 10/36
Product Specification
Backlight Unit
RxIN0
Lamp Connector(2pin)
LCD Connector(
30
pin)
3. Functional Block Diagram
The following diagram shows the functional block of the 15.4 inches wide Color TFT/LCD Module:
AU OPTRONICS CORPORATION
X-Driver
(4 pairs LVDS)
RxIN1
RxIN2
RxCLKIN
VDD
GND
www.jxlcd.com
JAE FI-XB30SL-HF10
www.jxlcd.com
Mating Housing JAE FI-X30H
LCD DRIVE
BOARD
LCD
Controller
DC-DC
Converter
Ref circuit
TFT ARRAY/CELL
1280(R/G/B) x 3 x 800
Y-Driver
JST BHSR-02VS-1
Mating Type SM02B-BHSS-1-TB
document version 0.1 11/36
Product Specification
4. Absolute Maximum Ratings
Absolute maximum ratings of the module is as following:
4.1 Absolute Ratings of TFT LCD Module
Item Symbol Min Max Unit Conditions
AU OPTRONICS CORPORATION
Logic/LCD Drive Voltage
Vin -0.3 +4.0 [Volt] Note 1,2
4.2 Absolute Ratings of Backlight Unit
Item Symbol Min Max Unit Conditions
CCFL Current ICCFL - 7.0 [mA] rms Note 1,2
4.3 Absolute Ratings of Environment
Item Symbol Min Max Unit Conditions
Operating Temperature
Operation Humidity HOP 5 95 [%RH] Note 3
Storage Temperature
Storage Humidity HST
Note 1: At Ta (25℃ )
Note 2: Permanent damage to the device may occur if exceed maximum values
Note 3: For quality performance, please refer to AUO IIS(Incoming Inspection Standard).
www.jxlcd.com
www.jxlcd.com
TOP 0 +50 [
TST -20 +60 [
5 95
Twb=39° C
o
C] Note 3
o
C] Note 3
[%RH]
Note 3
Operating Range Storage Range
document version 0.1 12/36
Product Specification
Voltage
90% 10%
5. Electrical characteristics
5.1 TFT LCD Module
5.1.1 Power Specification
Input power specifications are as follows;
AU OPTRONICS CORPORATION
Symble Parameter Min Typ Max Units
VDD Logic/LCD Drive
PDD VDD Power
IDD IDD Current
IRush Inrush Current
VDDrp Allowable
3.0 3.3 3.6 [Volt]
1.6 [Watt] Note 1
350
450
2000 [mA]
100 [mV]
Logic/LCD Drive
Ripple Voltage
Note 1 : Maximum Measurement Condition：Black Patterm
Note 2：Measure Condition
(High to Low)
Control
Signal
SW1
SW MAG-SPST
1 2
+5.0V
R1
47K
www.jxlcd.com
www.jxlcd.com
R2
1K
+12.0V
VR1
47K
D6
D5
D2 S
D1
G
C3
0.01uF/25V
Q3
AO6402
D2SD1D5
G
D6
Q3
AO6402
F1
C1
1uF/16V
[mA]
Note 1
Note 2
p-p
VCC
(LCD Module Input)
Note
C2
1uF/25V
3.3V
0V
0.5ms
document version 0.1 13/36
Vin rising time
Product Specification
VSS
5.1.2 Signal Electrical Characteristics
Input signals shall be low or High-impedance state when VDD is off.
It is recommended to refer the specifications of THC63LVDF84A(Thine Electronics Inc.) in
detail.
Signal electrical characteristics are as follows;
AU OPTRONICS CORPORATION
Parameter
Vth
Vtl
Vcm
Note: LVDS Signal Waveform
Vth
Vtl
Differential Input High
Threshold (Vcm=+1.2V)
Differential Input Low
Threshold (Vcm=+1.2V)
Differential Input
Common Mode Voltage
www.jxlcd.com
www.jxlcd.com
Condition Min Max Unit
Vcm
-100
1.125
100
1.375
[mV]
[mV]
[V]
document version 0.1 14/36
Product Specification
Note 2
5.2 Backlight Unit
Parameter guideline for CCFL Inverter
AU OPTRONICS CORPORATION
Parameter Min Typ Max
Units Condition
White Luminance
5 points average
170 200 - [cd/m2 ]
CCFL current(ICCFL) 2.0 6.0 7.0 [mA] rms
CCFL Frequency(FCCFL) 50 62 70 [KHz]
CCFL Ignition Voltage(Vs)
CCFL Ignition Voltage(Vs)
CCFL discharge time(sec)
1750
1460
1
[Volt] rms
[Volt] rms
CCFL Voltage (Reference)
628 700 792
[Volt] rms
(VCCFL)
CCFL Power consumption
- 4.20 4.40
[Watt]
(PCCFL)
Note 1: Typ are AUO recommended Design Points.
www.jxlcd.com
www.jxlcd.com
(Ta=25℃)
(Ta=25℃)
(Ta=25℃)
Note 3,4
(Ta= 0℃)
Note 5
(Ta= 25℃)
Note 5
(Ta= 25℃)
Note 1
(Ta=25℃)
Note 6
(Ta=25℃)
Note 6
*1 All of characteristics listed are measured under the condition using the AUO Test inverter.
*2 In case of using an inverter other than listed, it is recommended to check the inverter carefully.
Sometimes, interfering noise stripes appear on the screen, and substandard luminance or flicker at low power
may happen.
*3 In designing an inverter, it is suggested to check safety circuit very carefully. Impedance of CCFL, for
instance, becomes more than 1 [M ohm] when CFL is damaged.
*4 Generally, CCFL has some amount of delay time after applying kick-off voltage. It is recommended to keep
on applying kick-off voltage for 1 [Sec] until discharge.
*5 CCFL discharge frequency must be carefully chosen so as not to produce interfering noise stripes on the
screen.
*6 Reducing CCFL current increases CCFL discharge voltage and generally increases CCFL discharge
frequency. So all the parameters of an inverter should be carefully designed so as not to produce too much
leakage current from high-voltage output of the inverter.
Note 2: It should be employed the inverter which has “Duty Dimming”, if ICCFL is less than 4mA.
Note 3: CCFL discharge frequency should be carefully determined to avoid interference between inverter and TFT
LCD.
document version 0.1 15/36
Product Specification
Note 4: The frequency range will not affect to lamp life and reliability characteristics.
Note 5: CCFL inverter should be able to give out a power that has a generating capacity of over 1,430 voltage.
Lamp units need 1,400 voltage minimum for ignition.
Note 6: Calculator value for reference (ICCFL×VCCFL=PCCFL)
Note 7: Requirements for a system inverter design, which is intended to have a better display performance, a better
power efficiency and a more reliable lamp, are following.
It shall help increase the lamp lifetime and reduce leakage current.
a. The asymmetry rate of the inverter waveform should be less than 10%.
b. The distortion rate of the waveform should bewithin √2 ±10%.
* Inverter output waveform had better be more similar to ideal sine wave.
AU OPTRONICS CORPORATION
www.jxlcd.com
www.jxlcd.com
document version 0.1 16/36
Product Specification
R G B R G B R G B R G B R G B R G B 0 1
6. Signal Characteristic
6.1 Pixel Format Image
Following figure shows the relationship of the input signals and LCD pixel format.
AU OPTRONICS CORPORATION
1278 1279
1st Line
800th Line
R G B R G B
www.jxlcd.com
www.jxlcd.com
document version 0.1 17/36
Product Specification
Data Clock
6.2 The input data format
Signal Name
R5
R4
R3
R2
R1
R0
Description
Red Data 5 (MSB)
Red Data 4
Red Data 3
Red Data 2
Red Data 1
Red Data 0 (LSB)
Red-pixel Data
AU OPTRONICS CORPORATION
Red-pixel Data
Each red pixel's brightness data consists of
these 6 bits pixel data.
G5
G4
G3
G2
G1
G0
B5
B4
B3
B2
B1
B0
RxCLKIN
DE Display Timing This signal is strobed at the falling edge of
VS Vertical Sync The signal is synchronized to RxCLKIN .
HS Horizontal Sync The signal is synchronized to RxCLKIN .
Note: Output signals from any system shall be low or High-impedance state when VDD is off.
www.jxlcd.com
www.jxlcd.com
Green Data 5 (MSB)
Green Data 4
Green Data 3
Green Data 2
Green Data 1
Green Data 0 (LSB)
Green-pixel Data
Blue Data 5 (MSB)
Blue Data 4
Blue Data 3
Blue Data 2
Blue Data 1
Blue Data 0 (LSB)
Blue-pixel Data
Green-pixel Data
Each green pixel's brightness data consists of
these 6 bits pixel data.
Blue-pixel Data
Each blue pixel's brightness data consists of
these 6 bits pixel data.
The typical frequency is 68.9 MHZ.. The signal
is used to strobe the pixel data and DE signals.
All pixel data shall be valid at the falling edge
when the DE signal is high.
RxCLKIN. When the signal is high, the pixel
data shall be valid to be displayed.
document version 0.1 18/36
Product Specification
6.3 Signal Description/Pin Assignment
LVDS is a differential signal technology for LCD interface and high speed data transfer device.
AU OPTRONICS CORPORATION
PIN# Signal Name
1 GND Ground
2 VDD +3.3V Power Supply
3 VDD +3.3V Power Supply
4 V
5 NC No Connection (Reserve for AUO test)
6 CLK
7 DATA
8 RxIN0- LVDS differential data input(R0-R5, G0)
9 RxIN0+ LVDS differential data input(R0-R5, G0)
10 GND Ground
11 RxIN1- LVDS differential data input(G1-G5, B0-B1)
12 RxIN1+ LVDS differential data input(G1-G5, B0-B1)
13 GND Ground
14 RxIN2- LVDS differential data input(B2-B5, HS, VS, DE)
15 RxIN2+ LVDS differential data input(B2-B5, HS, VS, DE)
16 GND Ground
17 RxCLKIN- LVDS differential clock input
www.jxlcd.com
www.jxlcd.com
+3.3V EDID Power
EDID
EDID Clock Input
EDID
EDID Data Input
EDID
Description
18 RxCLKIN+ LVDS differential clock input
19 GND Ground
20 NC No Connection (Reserve for AUO test)
21 NC No Connection (Reserve for AUO test)
22 GND Ground
23 NC No Connection (Reserve for AUO test)
24 NC No Connection (Reserve for AUO test)
25 GND Ground
26 NC No Connection (Reserve for AUO test)
27 NC No Connection (Reserve for AUO test)
28 NC No Connection (Reserve for AUO test)
29 NC No Connection (Reserve for AUO test)
30 NC No Connection (Reserve for AUO test)
document version 0.1 19/36
Product Specification
1
NC
GND
Connector
Note1: Start from right side
Note2: Input signals shall be low or High-impedance state when VDD is off.
www.jxlcd.com
www.jxlcd.com
30
AU OPTRONICS CORPORATION
document version 0.1 20/36
Product Specification
R R R R
9
12
15 17 18 8
internal circuit of LVDS inputs are as following.
The module uses a 100ohm resistor between positive and negative data lines of each receiver input
Signal Input
Pin No.
RxIN0-
RxIN0+
11
RxIN1-
RxIN1+
14
RxIN2-
RxIN2+
RxCLKIN-
RxCLKIN+
AU OPTRONICS CORPORATION
LVDS Receiver
www.jxlcd.com
www.jxlcd.com
document version 0.1 21/36
Product Specification
6.4 Interface Timing
6.4.1 Timing Characteristics
Basically, interface timings should match the 1280x800 /60Hz manufacturing guide line timing.
Parameter Symbol Min. Typ. Max. Unit
Frame Rate - 50 60 - Hz
AU OPTRONICS CORPORATION
Vertical
Section
Horizontal
Section
Clock frequency 1/ T
Period TV 803 816 1023
Active T
Blanking T
Period TH 1303 1408 2047
Active T
Blanking T
50 68.9 80 MHz
Clock
VD
VB
HD
HB
800 800 800
3 16 223
- 1280 -
23 128 767
Note : DE mode only
www.jxlcd.com
www.jxlcd.com
T
T
Line
Clock
document version 0.1 22/36
6.4.2 Timing diagram
T
CLOCK
DOTCLK
Input
Data
DE
DE
www.jxlcd.com
www.jxlcd.com
Invaild
Data
Product Specification
AU OPTRONICS CORPORATION
Input Timing Definition ( DE Mode)
Pixel
1
T
HB
T
VB
Pixel
2
T
Pixel
3
T
HD
H
T
V
Pixel
N-1
T
VD
Pixel
N
Invaild
Data
Pixel
1
document version 0.1 23/36
Product Specification
T3 T2
T1
T7
6.5 Power ON/OFF Sequence
VDD power and lamp on/off sequence is as follows. Interface signals are also shown in the chart.
Signals from any system shall be Hi-Z state or low level when VDD is off.
Power Supply VDD
Power Sequence Timing
Backlight On
www.jxlcd.com
www.jxlcd.com
AU OPTRONICS CORPORATION
T5
VALID
DATA
T6
Value
90%
10%
Parameter
T1 0.5 - 10 (ms)
T2 0 - 50 (ms)
T3 0 - 50 (ms)
T4 400 - - (ms)
T5 200 - - (ms)
T6 200 - - (ms)
Min. Typ. Max.
90%
10%
T4
Units
T7 0 - 10 (ms)
document version 0.1 24/36
Product Specification
7. Connector Description
Physical interface is described as for the connector on module.
These connectors are capable of accommodating the following signals and will be following
components.
7.1 TFT LCD Module
Connector Name / Designation For Signal Connector
Manufacturer JAE or compatible
Type / Part Number FI-XB30SL-HF10 or compatible
Mating Housing/Part Number FI-X30H or compatible
7.2 Backlight Unit
AU OPTRONICS CORPORATION
Physical interface is described as for the connector on module.
These connectors are capable of accommodating the following signals and will be following
components.
Connector Name / Designation For Lamp Connector
Manufacturer JST
Type / Part Number BHSR-02VS-1
Mating Type / Part Number SM02B-BHSS-1-TB
www.jxlcd.com
www.jxlcd.com
7.3 Signal for Lamp connector
Pin # Cable color Signal Name
1
2
Red
White
Lamp High Voltage
Lamp Low Voltage
document version 0.1 25/36
Product Specification
8. Vibration and Shock Test
8.1 Vibration Test
Test Spec:
Test method: Non-Operation
l
Acceleration: 1.5 G
l
Frequency: 10 - 500Hz Random
l
Sweep: 30 Minutes each Axis (X, Y, Z)
l
8.2 Shock Test Spec:
Test Spec:
Test method: Non-Operation
l
Acceleration: 220 G , Half sine wave
l
Active time: 2 ms
l
Pulse: X,Y,Z .one time for each side
l
AU OPTRONICS CORPORATION
www.jxlcd.com
www.jxlcd.com
document version 0.1 26/36
9. Reliability
Items
Temperature
Humidity Bias
High Temperature
Operation
Low Temperature
Operation
On/Off Test
Hot Storage
Cold Storage
Thermal Shock Test
Hot Start Test
Cold Start Test
Shock Test
(Non-Operating)
Product Specification
AU OPTRONICS CORPORATION
Required Condition Note
40℃/90%,300Hr
50℃/Dry,300Hr
0℃,300Hr
25℃,150hrs(ON/10 sec. OFF/10sec., 10,000 cycles)
60℃/35% RH ,250 hours
-20℃/50% RH ,250 hours
-20℃/30 min ,60℃/30 min 100cycles
50℃/1 Hr min. power on/off per 5 minutes, 5 times
0℃/1 Hr min. power on/off per 5 minutes, 5 times
220G, 2ms, Half-sine wave
Vibration Test
(Non-Operating)
ESD
Room temperature
Test
Note1: According to EN61000-4-2 , ESD class B: Some performance degradation allowed. No data lost
Note2: CCFL Life time: 12,000 hours minimum under normal module usage.
Note3: MTBF (Excluding the CCFL): 30,000 hours with a confidence level 90%
www.jxlcd.com
www.jxlcd.com
. Self-recoverable. No hardware failures.
Random vibration, 1.5 G zero-to-peak, 10 to 500 Hz,
30 mins in each of three mutually perpendicular axes.
Contact : ±8KV/ operation
Air : ±15KV / operation
25℃, 2000hours, Operating with loop pattern
Note 1
document version 0.1 27/36
10. Mechanical Characteristics
10.1 LCM Outline Dimension
www.jxlcd.com
www.jxlcd.com
Document version 0.1 28/36
www.jxlcd.com
www.jxlcd.com
Document version 0.1 29/36
10.2 Screw Hole Depth and Center Position
Screw hole minimum depth, from side surface =2.3 mm (See drawing)
Screw hole center location, from front surface = 3.7 ± 0.2mm (See drawing)
Screw Torque: Maximum 2.5 kgf-cm
www.jxlcd.com
www.jxlcd.com
Document version 0.1 30/36
Week code
M
odel name
11. Shipping and Package
11.1 Shipping Label Format
www.jxlcd.com
www.jxlcd.com
Document version 0.1 31/36
11.2. Carton package
The outside dimension of carton is 455 (L)mm x 380 (W)mm x 355 (H)mm
www.jxlcd.com
www.jxlcd.com
11.3 Shipping package of palletizing sequence
Top cardboard
Document version 0.1 32/36
Bottom cardboard
Wooden pallet
Note : Limit of box palletizing = Max 3 layers(ship and stock conditions)
Corner angle
PE band
Stretch film
12. Appendix: EDID description
Address
HEX HEX BIN DEC
00 Header 00 00000000 0
01 FF 11111111 255
02 FF 11111111 255
03 FF 11111111 255
04 FF 11111111 255
05 FF 11111111 255
06 FF 11111111 255
07 00 00000000 0
08 EISA Manuf. Code LSB 06 00000110 6
09 Compressed ASCII AF 10101111 175
0A
0B
0C 32-bit ser # 00 00000000 0
0D 00 00000000 0
0E 00 00000000 0
FUNCTION Value Value Value Note
Product Code
hex, LSB first
74 01110100 116
80 10000000 128
0F 00 00000000 0
10 Week of manufacture 01 00000001 1
11 Year of manufacture 10 00010000 16
12 EDID Structure Ver. 01 00000001 1
13 EDID revision # 03 00000011 3
14
15
16
17
18
19
www.jxlcd.com
www.jxlcd.com
Video input def. (digital I/P,
non-TMDS, CRGB)
Max H image size (rounded to
cm)
Max V image size (rounded to
cm)
Display Gamma
(=(gamma*100)-100)
Feature support (no DPMS,
Active OFF, RGB, tmg Blk#1)
Red/green low bits (Lower
2:2:2:2 bits)
80 10000000 128
21 00100001 33
15 00010101 21
78 01111000 120
0A 00001010 10
1C 00011100 28
Blue/white low bits (Lower
1A
1B
1C Red y/ highER 8 bits 58 01011000 88 0.345
1D Green x 50 01010000 80 0.315
2:2:2:2 bits)
Red x (Upper 8 bits)
Document version 0.1 33/36
F5 11110101 245
97 10010111 151 0.590
Horz&Vert Sync Offset/Width
1E Green y 8E 10001110 142 0.555
1F Blue x 27 00100111 39 0.155
20 Blue y 27 00100111 39 0.155
21 White x 50 01010000 80 0.313
22 White y 54 01010100 84 0.329
23 Established timing 1 00 00000000 0
24 Established timing 2 00 00000000 0
25 Established timing 3 00 00000000 0
26 Standard timing #1 01 00000001 1
27 01 00000001 1
28 Standard timing #2 01 00000001 1
29 01 00000001 1
2A Standard timing #3 01 00000001 1
2B 01 00000001 1
2C Standard timing #4 01 00000001 1
2D 01 00000001 1
2E Standard timing #5 01 00000001 1
2F 01 00000001 1
30 Standard timing #6 01 00000001 1
31 01 00000001 1
32 Standard timing #7 01 00000001 1
33 01 00000001 1
34 Standard timing #8 01 00000001 1
www.jxlcd.com
www.jxlcd.com
35 01 00000001 1
Pixel Clock/10000 LSB
36
Pixel Clock/10000 USB
37
Horz active Lower 8bits
38
Horz blanking Lower 8bits
39
HorzAct:HorzBlnk Upper 4:4
bits
3A
3B
3C
3D
3E
3F
40
41
Vertical Active Lower 8bits
Vertical Blanking Lower
8bits
Vert Act : Vertical Blanking
(upper 4:4 bit)
HorzSync. Offset
HorzSync.Width
VertSync.Offset :
VertSync.Width
C7 11000111 199
1B 00011011 27
00 00000000 0
A0 10100000 160
50 01010000 80
20 00100000 32
17 00010111 23
30 00110000 48
30 00110000 48
20 00100000 32
36 00110110 54
00 00000000 0
Document version 0.1 34/36
(zero for internal
Upper 2bits
Horizontal Image Size Lower
42
8bits 4B 01001011 75
43 Vertical Image Size Lower 8bits
Horizontal & Vertical Image Size
44
(upper 4:4 bits) 10 00010000 16
Horizontal Border
45
LCD)
Vertical Border (zero for internal
46
LCD)
Signal (non-intr, norm, no stero, sep
47
sync, neg pol)
48 Detailed timing/monitor 00 00000000 0
49 descriptor #2 00 00000000 0
4A 00 00000000 0
4B 0F 00001111 15
4C 00 00000000 0
4D 00 00000000 0
4E 00 00000000 0
4F 00 00000000 0
CF 11001111 207
00 00000000 0
00 00000000 0
18 00011000 24
50 00 00000000 0
51 00 00000000 0
52 00 00000000 0
53 00 00000000 0
54 00 00000000 0
55 00 00000000 0
56 00 00000000 0
57 00 00000000 0
58 00 00000000 0
59 20 00100000 32
5A Detailed timing/monitor 00 00000000 0
5B descriptor #3 00 00000000 0
5C 00 00000000 0
5D FE 11111110 254
5E 00 00000000 0
5F Manufacture 41 01000001 65 A
60 Manufacture 55 01010101 85 U
www.jxlcd.com
www.jxlcd.com
61 Manufacture 4F 01001111 79 O
62 0A 00001010 10
63 20 00100000 32
Document version 0.1 35/36
64 20 00100000 32
65 20 00100000 32
66 20 00100000 32
67 20 00100000 32
68 20 00100000 32
69 20 00100000 32
6A 20 00100000 32
6B 20 00100000 32
6C Detailed timing/monitor 00 00000000 0
6D descriptor #4 00 00000000 0
6E 00 00000000 0
6F FE 11111110 254
70 00 00000000 0
71 Manufacture P/N 42 01000010 66 B
72 Manufacture P/N 31 00110001 49 1
73 Manufacture P/N 35 00110101 53 5
74 Manufacture P/N 34 00110100 52 4
75 Manufacture P/N 45 01000101 69 E
76 Manufacture P/N 57 01010111 87 W
77 Manufacture P/N 30 00110000 48 0
78 Manufacture P/N 38 00111000 56 8
79 Manufacture P/N 20 00100000 32
7A Manufacture P/N 56 01010110 86 V
7B Manufacture P/N 30 00110001 49 1
7C 20 00100000 32
7D 0A 00001010 10
7E Extension Flag 00 00000000 0
7F Checksum 45 01000101 69
www.jxlcd.com
www.jxlcd.com
Document version 0.1 36/36
Loading...