) Preliminary Specifications
(V
( ) Final Specifications
Product Specification
AU OPTRONICS CORPORATION
Module
Model Name
15.4” WXGA Color TFT-LCD
B154EW02 V7
Customer Date
Checked &
Approved by
www.jxlcd.com
www.jxlcd.com
Approved by Date
Joselyn Liu
Prepared by
2006/10/21
Jerry Chen 2006/10/21
Note: This Specification is subject to change
without notice.
document version 0.0 1/36
Ivy Lee
MDBU Marketing Division /
AU Optronics corporation
2006/10/21
Product Specification
AU OPTRONICS CORPORATION
Contents
Contents....................................................................................................................2
1. Handling Precautions...........................................................................................4
2. General Description..............................................................................................5
2.1 General Specification.........................................................................................................5
2.2 Optical Characteristics.......................................................................................................6
3. Functional Block Diagram..................................................................................11
4. Absolute Maximum Ratings...............................................................................12
4.1 Absolute Ratings of TFT LCD Module..............................................................................12
4.2 Absolute Ratings of Backlight Unit...................................................................................12
4.3 Absolute Ratings of Environment.....................................................................................12
5. Electrical characteristics....................................................................................13
5.1 TFT LCD Module..............................................................................................................13
5.1.1 Power Specification.............................................................................................................................13
5.1.2 Signal Electrical Characteristics...........................................................................................................14
5.2 Backlight Unit...................................................................................................................15
6. Signal Characteristic..........................................................................................17
6.1 Pixel Format Image..........................................................................................................17
6.2 The input data format.......................................................................................................18
6.3 Signal Description/Pin Assignment...................................................................................19
6.4 Interface Timing................................................................................................................22
7. Connector Description.......................................................................................25
7.1 TFT LCD Module..............................................................................................................25
7.2 Backlight Unit...................................................................................................................25
7.3 Signal for Lamp connector...............................................................................................25
8. Vibration and Shock Test...................................................................................26
8.1 Vibration Test....................................................................................................................26
8.2 Shock Test Spec:..............................................................................................................26
9. Reliability.............................................................................................................27
10. Mechanical Characteristics..............................................................................28
10.1 LCM Outline Dimension.................................................................................................28
10.2 Screw Hole Depth and Center Position..........................................................................30
11. Shipping and Package......................................................................................31
www.jxlcd.com
www.jxlcd.com
6.4.1 Timing Characteristics.........................................................................................................................22
6.4.2 Timing diagram....................................................................................................................................23
6.5 Power ON/OFF Sequence......................................................................................................................24
11.1 Shipping Label Format...................................................................................................31
11.2. Carton package.............................................................................................................32
11.3 Shipping package of palletizing sequence.....................................................................32
12. Appendix: EDID description.............................................................................33
document version 0.0 2/36
Product Specification
AU OPTRONICS CORPORATION
Record of Revision
Version and Date Page
0.1 2006/10/21 All First Edition for Customer
www.jxlcd.com
www.jxlcd.com
Old description New Description Remark
document version 0.0 3/36
Product Specification
1. Handling Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or
spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard
surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human
earth when handling.
7) Do not open nor modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) In case if a Module has to be put back into the packing container slot after once it was
taken out from the container, do not press the center of the CCFL Reflector edge.
Instead, press at the far ends of the CFL Reflector edge softly. Otherwise the TFT
Module may be damaged.
10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt
the Interface Connector of the TFT Module.
11) After installation of the TFT Module into an enclosure (Notebook PC Bezel, for
example), do not twist nor bend the TFT Module even momentary. At designing the
enclosure, it should be taken into consideration that no bending/twisting forces are
applied to the TFT Module from outside. Otherwise the TFT Module may be damaged.
12) Cold cathode fluorescent lamp in LCD contains a small amount of mercury. Please follow local
ordinances or regulations for disposal.
13) Small amount of materials having no flammability grade is used in the LCD module. The LCD
module should be supplied by power complied with requirements of Limited Power Source(,
IEC60950 or UL1950), or be applied exemption.
14) The LCD module is designed so that the CCFL in it is supplied by Limited Current
Circuit(IEC60950 or UL1950). Do not connect the CCFL in Hazardous Voltage Circuit.
www.jxlcd.com
www.jxlcd.com
AU OPTRONICS CORPORATION
document version 0.0 4/36
Product Specification
(
Note1
)
550 max.
Storage (
Non
-
Operating)
[oC]
RoHS Compliance
2. General Description
B154EW02 V7 is a Color Active Matrix Liquid Crystal Display composed of a TFT LCD panel, a
driver circuit, and backlight system. The screen format is intended to support the WXGA (1280(H)
x 800(V)) screen and 262k colors (RGB 6-bits data driver). All input signals are LVDS interface
compatible. Inverter of backlight is not included.
B154EW02 V7 is designed for a display unit of notebook style personal computer and industrial
machine.
2.1 General Specification
The following items are characteristics summary on the table at 25 ℃ condition:
Items Unit Specifications
Screen Diagonal [mm] 391 (15.4W”)
Active Area [mm] 331.2 X 207.0
AU OPTRONICS CORPORATION
Pixels H x V 1280x3(RGB) x 800
Pixel Pitch [mm] 0.2588X0.2588
Pixel Arrangement R.G.B. Vertical Stripe
Display Mode Normally White
www.jxlcd.com
White Luminance (ICCFL=6.0mA)
Note: ICCFL is lamp current
Luminance Uniformity 1.25 max. (5 points)
Contrast Ratio 400 typ
Response Time [msec] 8 typ.
Nominal Input Voltage VDD [Volt] +3.3 typ.
Power Consumption [Watt] 6.0 max.(without inverter)
Weight [Grams] 525 typ.
Physical Size [mm] 344.0 typ. x 222.0 typ. x 6.1 max.
Electrical Interface 1 channel LVDS
www.jxlcd.com
[cd/m2] 200 typ. (5 points average)
170 min. (5 points average)
300 min.
Surface Treatment Glare, Hardness 3H,
Support Color 262K colors ( RGB 6-bit )
Temperature Range
Operating
RoHS Compliance
document version 0.0 5/36
[oC]
0 to +50
-20 to +60
Product Specification
2.2 Optical Characteristics
The optical characteristics are measured under stable conditions at 25 ℃ (Room Temperature):
Item Unit Conditions Min. Typ. Max. Note
AU OPTRONICS CORPORATION
White Luminance
ICCFL=6.0mA
Viewing Angle
Luminance Uniformity
Luminance Uniformity
CR: Contrast Ratio
Cross talk %
Response Time
Color / Chromaticity
Coordinates
(CIE 1931)
www.jxlcd.com
www.jxlcd.com
[cd/m2] 5 points average
[degree]
[degree]
[degree]
[degree]
[msec] Rising
[msec] Falling
[msec] Rising + Falling
Horizontal (Right)
CR = 10 (Left)
Vertical (Upper)
CR = 10 (Lower)
5 Points
13 Points
300 400 - 6
4 7
Red x
Red y
Green x
Green y
Blue x
Blue y
White x
White y
170 200 - 1, 4, 5.
-
-
-
-
1.25 1
1.50 2
-
- 2 5
8 14
0.560 0.590 0.620
0.315 0.345 0.375
0.285 0.315 0.345
0.520 0.555 0.585
0.125 0.155 0.185
0.125 0.155 0.185
0.283 0.313 0.343
0.299 0.329 0.359
45
45
15
35
6
-
-
-
-
9
8
8
2,8
document version 0.0 6/36
Product Specification
= Maximum Brightness of thirteen points
Minimum Brightness of thirteen points
Maximum Brightness of five
points
= Minimum Brightness of five
point
s
Note 1: 5 points position (Display area : 331.2mm x 207.0mm)
Note 2: 13 points position
H/4
H/4
H
H/4
H/4
AU OPTRONICS CORPORATION
W
W/4 W/4 W/4 W/4
12
45
W/4
10
W/4
3
W
W/4
W/4
10
10
H/4
www.jxlcd.com
www.jxlcd.com
H/4
H
H/4
H/4
10
1
4
6
9
11
Note 3: The luminance uniformity of 5 and 13 points is defined by dividing the maximum luminance values by the
minimum test point luminance
δ
W5
2
5
7
10
3
8
1312
δ
W13
document version 0.0 7/36
Product Specification
Field=2
°
Contrast ratio (CR)=
Brightness on the “White” state
Brightness on the “Black” state
Note 4: Measurement method
The LCD module should be stabilized at given temperature for 30 minutes to avoid abrupt temperature change
during measuring. In order to stabilize the luminance, the measurement should be executed after lighting Backlight
for 30 minutes in a stable, windless and dark room.
AU OPTRONICS CORPORATION
Photo detector
Note 5： Definition of Average Luminance of White (YL):
Measure the luminance of gray level 63 at 5 points，Y
L (x) is corresponding to the luminance of the point X at Figure in Note (1).
Note 6： Definition of contrast ratio:
www.jxlcd.com
www.jxlcd.com
= [L (1)+ L (2)+ L (3)+ L (4)+ L (5)] / 5
L
Contrast ratio is calculated with the following formula.
document version 0.0 8/36
Product Specification
Note 7： Definition of Cross Talk (CT)
CT = | YB – YA | / YA × 100 (%)
Where
YA = Luminance of measured location without gray level 0 pattern (cd/m 2)
YB = Luminance of measured location with gray level 0 pattern (cd/m 2)
Note 8: Definition of response time:
AU OPTRONICS CORPORATION
The output signals of BM-7 or equivalent are measured when the input signals are changed from “Black” to “White”
(falling time) and from “White” to “Black” (rising time), respectively. The response time interval between the 10% and
90% of amplitudes. Refer to figure as below.
www.jxlcd.com
www.jxlcd.com
100%
S
i
90%
g
n
a
l
(
R
e
l
a
t
i
v
e
v
a
l
u
10%
e
)
0%
Tr
"Black"
"White""White"
Tf
document version 0.0 9/36
Product Specification
Note 8. Definition of viewing angle
Viewing angle is the measurement of contrast ratio ≧10, at the screen center, over a 180° horizontal and 180°
vertical range (off-normal viewing angles). The 180° viewing angle range is broken down as follows; 90 ° (θ)
horizontal left and right and 90° (Φ) vertical, high (up) and low (down). The measurement direction is typically
perpendicular to the display surface with the screen rotated about its center to develop the desired measurement
viewing angle.
AU OPTRONICS CORPORATION
www.jxlcd.com
www.jxlcd.com
document version 0.0 10/36
Product Specification
Backlight Unit
RxIN0
Lamp Connector(2pin)
LCD Connector(
30
pin)
3. Functional Block Diagram
The following diagram shows the functional block of the 15.4 inches wide Color TFT/LCD Module:
AU OPTRONICS CORPORATION
X-Driver
(4 pairs LVDS)
RxIN1
RxIN2
RxCLKIN
VDD
GND
JAE FI-XB30SL-HF10
Mating Housing JAE FI-X30H
www.jxlcd.com
www.jxlcd.com
LCD DRIVE
BOARD
LCD
Controller
DC-DC
Converter
Ref circuit
Y-Driver
TFT ARRAY/CELL
1280(R/G/B) x 3 x 800
JST BHSR-02VS-1
Mating Type SM02B-BHSS-1-TB
document version 0.0 11/36
Loading...