Product Specification
( V ) Preliminary Specification
( ) Final Specification
Module 14.0” (13.97”) HD 16:9 Color TFT-LCD
Model Name B140XW02 V2 (1A)
with LED Backlight design
AU OPTRONICS CORPORATION
Note ( )
Customer Date
www.jxlcd.com
www.jxlcd.com
Checked &
Approved by
LED Backlight with driving circuit design
Date
Approved by Date
Bonnie Chen
Prepared by Date
07/14/2009
Note: This Specification is subject t o change
without notice.
Jonken Fan
NBBU Marketing Division
AU Optronics corporation
07/14/2009
B140XW02 V2 Document Version : 0.3
1 of 29
Product Specification
AU OPTRONICS CORPORATION
Contents
1. Handling Precautions .............................................................. 4
2. General Description................................................................. 5
2.1 General Specification...........................................................................................................................5
2.2 Optical Characteristics.........................................................................................................................6
3. Functional Block Diagram...................................................... 11
4. Absolute Maximum Ratings................................................... 12
4.1 Absolute Ratings of TFT LCD Module .............................................................................................12
4.2 Absolute Ratings of Environment......................................................................................................12
5. Electrical Characteristics ....................................................... 13
5.1 TFT LCD Module..............................................................................................................................13
5.2 Backlight Unit....................................................................................................................................15
6. Signal Interface Characteristic.............................................. 16
6.1 Pixel Format Image............................................................................................................................16
6.2 The Input Data Format ......................................................................................................................17
6.3 Integration Interface Requirement ....................................................................................................18
6.4 Interface Timing.................................................................................................................................20
7. Panel Reliability Test ............................................................ 22
7.1 Vibration Test.....................................................................................................................................22
7.2 Shock Test..........................................................................................................................................22
www.jxlcd.com
7.3 Reliability Test ...................................................................................................................................22
www.jxlcd.com
8. Mechanical Characteristics .................................................... 23
8.1 LCM Outline Dimension ...................................................................................................................23
9. Shipping and Package ........................................................... 25
9.1 Shipping Label Format.......................................................................................................................25
9.2 Carton Package..................................................................................................................................26
9.3 Shipping Package of Palletizing Sequence ........................................................................................26
10. Appendix: EDID Description ................................................ 27
B140XW02 V2 Document Version : 0.3
2 of 29
Product Specification
AU OPTRONICS CORPORATION
Record of Revision
Version and Date Page
1 2009/04/21 0.1 All First Edition for Customer
2 2009/05/20 0.2 27 TBD Add EDID
3 2009/07/14 0.3 5 Pixel pitch: TBD Pixel pitch: TBD
6 5 point Luminance unif or mity: TBD 5 point Luminance unif or mity: 1.25
6 13 point Luminance uniformity: TBD 13 point Luminance uniformity: 1.60
15 BLU unit: TBD BLU unit: add updated tables
24 Old back-view drawing New back-view drawing
www.jxlcd.com
www.jxlcd.com
Old description New Description Remark
B140XW02 V2 Document Version : 0.3
3 of 29
Product Specification
1. Handling Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input
connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration
or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on
hard surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure
human earth when handling.
7) Do not open nor modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
AU OPTRONICS CORPORATION
9) At the insertion or removal of the Signal Interface Connector, be sure not to rotate
nor tilt the Interface Connector of the TFT Module.
11) After installation of the TFT Module into an enclosure (Notebook PC Bezel, for
example), do not twist nor bend the TFT Module even momentary. At designing the
enclosure, it should be taken into consideration that no bending/twisting forces are
applied to the TFT Module from outside. Otherwise the TFT Module may be
damaged.
12) Small amount of materials having no flammability grade is used in the LCD module. The
LCD module should be supplied by power complied with requirements of Limited Power
Source (IEC60950 or UL1950), or be applied exemption.
13) Disconnecting power supply before handling LCD modules, it can prevent electric shock,
DO NOT TOUCH the electrode parts, cables, connectors and LED circuit part of TFT
module that a LED light bar build in as a light source of back light unit. It can prevent
electronic breakdown.
www.jxlcd.com
www.jxlcd.com
B140XW02 V2 Document Version : 0.3
4 of 29
Product Specification
2. General Description
B140XW02 V2 is a Color Active Matrix Liquid Crystal Display composed of a TFT LCD panel,
a driver circuit, and LED backlight system. The screen format is intended to support the 16:9
HD, 1366(H) x768(V) screen and 262k colors (RGB 6-bits data driver) with LED backlight
driving circuit. All input signals are LVDS interface compatible.
B140XW02 V2 is designed for a display unit of notebook style personal computer and
industrial machine.
AU OPTRONICS CORPORATION
2.1 General Specification
The following items are characteristics summary on the table at 25 ℃ condition:
Items Unit Specifications
Screen Diagonal [mm] 354, 14.0”(13.97”)
Active Area [mm] 309.399 x 173.952
Pixels H x V 1366 x 3(RGB) x 768
Pixel Pitch [mm] 0.2265 x 0.2265
Pixel Format B.G.R. Vertical Stripe
Display Mode Normally White
White Luminance (I
(Note: ILED is LED current)
Luminance Uniformity 1.25 max. (5 points)
Contrast Ratio 500 typ
www.jxlcd.com
www.jxlcd.com
LED
=20mA)
[cd/m2] 200 typ. (5 points average)
170 min. (5 points average)
Response Time [ms] 8 typ / 16 Max
Nominal Input Voltage VDD [Volt] +3.3 typ.
Power Consumption [Watt] 3.8W Max
Weight [Grams] 320 max.
Min. Typ. Max.
Physical Size
Include bracket
Electrical Interface 1 channel LVDS
Glass Thickness [mm] 0.5
Surface Treatment Glare, Hardness 3H,
B140XW02 V2 Document Version : 0.3
[mm]
Length 319.9 320.4 320.9
Width 204.6 205.1 205.6
Thickness
- - 3.6
5 of 29
Product Specification
RoHS Compliance
Support Color 262K colors ( RGB 6-bit )
AU OPTRONICS CORPORATION
Temperature Range
Operating
Storage (Non-Operating)
[oC]
[oC]
0 to +50
-20 to +60
RoHS Compliance
2.2 Optical Characteristics
The optical characteristics are measured under stable conditions at 25℃ (Room Temperature) :
Item Symbol
White Luminance
I
LED
=20mA
Viewing Angle
Luminance
Uniformity
Luminance
Uniformity
Contrast Ratio CR
www.jxlcd.com
www.jxlcd.com
δδδδ
Cross talk %
5 points average 170 200 -
θθθθR
θθθθL
ψψψψH
ψψψψL
δδδδ5P 5 Points
13 Points
13P
Tr Rising
Conditions Min. Typ. Max. Unit Note
Horizontal (Right)
CR = 10 (Left)
Vertical (Upper)
CR = 10 (Lower)
40
40
10
30
45
45
15
35
-
-
-
-
- - 1.25
- - 1.60
400 500 -
- - 4
-
2
-
cd/m
degree
2
1, 4, 5.
4, 9
1, 3, 4
2, 3, 4
4, 6
4, 7
Response Time
Color /
Chromaticity
Coodinates
Red
Green
Blue
Tf Falling
TRT Rising + Falling
Rx
Ry
Gx
Gy
Bx
CIE 1931
By
Wx
- 6 -
- 8 16
TBD TBD TBD
TBD
TBD TBD
TBD
TBD TBD
TBD
TBD TBD
TBD
TBD TBD
TBD
TBD TBD
0.263 0.313 0.363
msec
4, 8
White
Wy
NTSC %
B140XW02 V2 Document Version : 0.3
0.279 0.329 0.379
42 45 -
6 of 29
4
Product Specification
Maximum Brightness of thirteen points
Maximum Brightness of five
points
Minimum Brightness of five points
Note 1: 5 points position (Ref: Active area)
H /4
H /4
AU OPTRONICS CORPORATION
W / 4 W / 4 W /4 W /4
W
1 2
Note 2
W /4
3
5
W
W /4
2
7
H
H /4
4
H /4
: 13 points position (Ref: Active area)
W /4
1 0
1 0
H /4
www.jxlcd.com
www.jxlcd.com
H /4
H
H /4
1
4 5
6
W /4
1 0
3
8
H /4
Note 3
minimum test point luminance
: The luminance uniformity of 5 or13 points is defined by dividing the maximum luminance values by the
δ
=
W5
1 0
1 1
9
1 2
1 0
1 3
Note 4
during measuring. In order to stabilize the luminance, the measurement should be executed after lighting Backlight
B140XW02 V2 Document Version : 0.3
: Measurement method
The LCD module should be stabilized at given temperature for 30 minutes to avoid abrupt temperature change
δ
W13
=
Minimum Brightness of thirteen points
7 of 29
Product Specification
Center of the sc
reen TFT-LCD Module
50 cm
LCD Panel
Field=2
°
Contrast ratio (CR)=
Brightness on the “White” state
Brightness on the “Black” state
for 30 minutes in a stable, windless and dark room, and it should be measured in the center of screen.
AU OPTRONICS CORPORATION
Photo detector
Note 5
Note 6
Note 7
：
Definition of Average Luminance of White (YL):
Measure the luminance of gray level 63 at 5 points，Y
L (x) is corresponding to the luminance of the point X at Figure in Note (1).
CT = | YB – YA | / YA × 100 (%)
www.jxlcd.com
www.jxlcd.com
：
Definition of contrast ratio:
Contrast ratio is calculated with the following formula.
：
Definition of Cross Talk (CT)
= [L (1)+ L (2)+ L (3)+ L (4)+ L (5)] / 5
L
Where
YA = Luminance of measured location without gray level 0 pattern (cd/m2)
YB = Luminance of measured location with gray level 0 pattern (cd/m2)
B140XW02 V2 Document Version : 0.3
8 of 29
Product Specification
AU OPTRONICS CORPORATION
Note 8
“White” (falling time) and from “White” to “Black” (rising time), respectively. The response time interval between
the 10% and 90% of amplitudes. Refer to figure as below.
: Definition of response time:
The output signals of BM-7 or equivalent are measured when the input signals are changed from “Black” to
"Black"
100%
S
i
g
90%
n
a
l
(
R
e
l
a
t
i
v
www.jxlcd.com
e
www.jxlcd.com
v
a
l
u
10%
e
)
0%
Tr
Tf
"White""White"
B140XW02 V2 Document Version : 0.3
9 of 29
Product Specification
Note 9
180° vertical range (off-normal viewing angles). The 180° viewing angle range is broken down as follows; 90° (θ)
horizontal left and right and 90° (Φ) vertical, high (up) and low (down). The measurement direction is typically
perpendicular to the display surface with the screen rotated about its center to develop the desired measurement
viewing angle.
. Definition of viewing angle
Viewing angle is the measurement of contrast ratio ≧10, at the screen center, over a 180° horizontal and
AU OPTRONICS CORPORATION
www.jxlcd.com
www.jxlcd.com
B140XW02 V2 Document Version : 0.3
10 of 29
Product Specification
3. Functional Block Diagram
The following diagram shows the functional block of the 14.0 inches wide Color TFT/LCD 40 Pin one channel
Module
AU OPTRONICS CORPORATION
www.jxlcd.com
www.jxlcd.com
B140XW02 V2 Document Version : 0.3
11 of 29
Product Specification
4. Absolute Maximum Ratings
An absolute maximum rating of the module is as following:
4.1 Absolute Ratings of TFT LCD Module
Item Symbol Min Max Unit Conditions
Logic/LCD Drive Voltage
4.2 Absolute Ratings of Environment
Item Symbol Min Max Unit Conditions
Operating Temperature
Operation Humidity HOP 5 95 [%RH] Note 4
Storage Temperature
Storage Humidity HST
Note 1: At Ta (25℃ )
Note 2: Permanent damage to the device may occur if exceed maximum values
AU OPTRONICS CORPORATION
Vin -0.3 +4.0 [Volt] Note 1,2
TOP 0 +50 [oC] Note 4
TST -20 +60 [oC] Note 4
5 95
[%RH] Note 4
Note 3: LED specification refer to section 5.2
Note 4: For quality performance, please refer to AUO IIS (Incoming Inspection Standard).
Twb=39°C
www.jxlcd.com
www.jxlcd.com
Operating Range
B140XW02 V2 Document Version : 0.3
Storage Range
12 of 29
Product Specification
Voltage
-
90% 10%
5. Electrical Characteristics
5.1 TFT LCD Module
5.1.1 Power Specification
Input power specifications are as follows;
The power specification are measured under 25℃ and frame frenquency under 60Hz
Symble Parameter Min Typ Max Units Note
VDD
Logic/LCD Drive
AU OPTRONICS CORPORATION
3.0 3.3 3.6 [Volt]
PDD VDD Power
IDD IDD Current
I
Rush
Inrush Current
Allowable
VDDrp
Note 1 : Maximum Measurement Condition：Black Pattern at 3.3V driving voltage. (P
Note 2：Measure Condition
Logic/LCD Drive
Ripple Voltage
www.jxlcd.com
www.jxlcd.com
- -
- -
- -
- 1 [Watt]
333 [mA] Note 1
2000 [mA]
100
[mV]
p-p
max=V3.3
Note 1
Note 2
x I
black
)
0V
B140XW02 V2 Document Version : 0.3
3.3V
0.5ms
Vin rising time
13 of 29
Product Specification
5.1.2 Signal Electrical Characteristics
Input signals shall be low or High-impedance state when VDD is off.
Signal electrical characteristics are as follows;
Parameter Condition Min Max Unit
AU OPTRONICS CORPORATION
Vth
Vtl
VID
Vcm
Note: LVDS Signal Waveform
www.jxlcd.com
Differential Input High
Threshold (Vcm=+1.2V)
Differential Input Low
Threshold (Vcm=+1.2V)
Differential Input
Voltage
Differential Input
Common Mode Voltage
www.jxlcd.com
-
-100
100
1.125
100 [mV]
-
600
1.375
[mV]
[mV]
[V]
B140XW02 V2 Document Version : 0.3
14 of 29
5.2 Backlight Unit
5.2.1 LED characteristics
Product Specification
AU OPTRONICS CORPORATION
Parameter Symbol
Backlight Power
Consumption
LED Life-Time
Note 1: Calculator value for reference P
Note 2: The LED life-time define as the estimated time to 50% degradation of initial luminous.
5.2.2 Backlight input signal characteristics
Parameter Symbol Min Typ Max Units Remark
LED Power Supply VLED 7.0 12.0 21.0 [Volt]
www.jxlcd.com
www.jxlcd.com
LED Enable Input
High Level
LED Enable Input
Low Level
PWM Logic Input
High Level
PWM Logic Input
Low Level
PLED - - 2.8
N/A 12,000 - -
LED
VLED_EN
VPWM_EN
Min Typ Max Units
[Watt]
Hour
= VF (Normal Distribution) * IF (Normal Distribution) / Efficiency
2.5 - 5.5 [Volt]
- - 0.8 [Volt]
2.5 - 5.0
- - 0.8
[Volt]
[Volt]
Condition
(Ta=25℃), Note 1
Vin =12V
(Ta=25℃), Note 2
IF=20 mA
Define as
Connector
Interface
(Ta=25℃)
PWM Input Frequency
PWM Duty Ratio
B140XW02 V1 Document Version : 1.0
FPWM 100 - 20K
Duty 5 -- 100
Hz
%
15 of 29
Product Specification
6. Signal Interface Characteristic
6.1 Pixel Format Image
Following figure shows the relationship of the input signals and LCD pixel format.
AU OPTRONICS CORPORATION
www.jxlcd.com
www.jxlcd.com
B140XW02 V2 Document Version : 0.3
16 of 29
Product Specification
Data Clock
6.2 The Input Data Format
Signal Name
R5
R4
R3
R2
R1
R0
Description
Red Data 5 (MSB)
Red Data 4
Red Data 3
Red Data 2
Red Data 1
Red Data 0 (LSB)
Red-pixel Data
AU OPTRONICS CORPORATION
Red-pixel Data
Each red pixel's brightness data consists of
these 6 bits pixel data.
G5
G4
G3
G2
G1
G0
B5
B4
B3
B2
B1
B0
RxCLKIN
DE Display Timing This signal is strobed at the falling edge of
VS Vertical Sync The signal is synchronized to RxCLKIN .
HS Horizontal Sync The signal is synchronized to RxCLKIN .
Note: Output signals from any system shall be low or High-impedance state when VDD is off.
Green Data 5 (MSB)
Green Data 4
Green Data 3
www.jxlcd.com
www.jxlcd.com
Green Data 2
Green Data 1
Green Data 0 (LSB)
Green-pixel Data
Blue Data 5 (MSB)
Blue Data 4
Blue Data 3
Blue Data 2
Blue Data 1
Blue Data 0 (LSB)
Blue-pixel Data
Green-pixel Data
Each green pixel's brightness data consists of
these 6 bits pixel data.
Blue-pixel Data
Each blue pixel's brightness data consists of
these 6 bits pixel data.
The signal is used to strobe the pixel data and
DE signals. All pixel data shall be valid at the
falling edge when the DE signal is high.
RxCLKIN. When the signal is high, the pixel
data shall be valid to be displayed.
B140XW02 V2 Document Version : 0.3
17 of 29
Product Specification
6.3 Integration Interface Requirement
6.3.1 Connector Description
Physical interface is described as for the connector on module.
These connectors are capable of accommodating the following signals and will be following
components.
Connector Name / Designation For Signal Connector
Manufacturer IPEX or compatible
Type / Part Number IPEX 20455-040E-12A or compatible
Mating Housing/Part Number IPEX 20453-040T-11 or compatible
6.3.2 Pin Assignment
AU OPTRONICS CORPORATION
LVDS is a differential signal technology for LCD interface and high speed data transfer device.
B140XW02 V2
Pin
1 NC No Connection (Reserve)
2 VDD PowerSupply,3.3V(typical)
3 VDD PowerSupply,3.3V(typical)
www.jxlcd.com
www.jxlcd.com
4 DVDD DDC 3.3Vpower
5 NC No Connection (Reserve)
6 SCL DDC Clock
7 SDA DDC Data
8 Rin0- -LVDS differential data input(R0-R5,G0)
9 Rin0+ +LVDS differential data input(R0-R5,G0)
10
11
12
13
14
15
16
17
18
19
20
21
22
23
Signal Description
GND Ground
Rin1- -LVDS differential data input(G1-G5,B0-B1)
Rin1+ +LVDS differential data input(G1-G5,B0-B1)
GND Ground
Rin2- -LVDS differential data input(B2-B5,HS,VS,DE)
Rin2+ +LVDS differential data input(B2-B5,HS,VS,DE)
GND Ground
ClkIN- -LVDS differential clock input
ClkIN+ +LVDS differential clock input
GND Ground
NC No Connection (Reserve)
NC No Connection (Reserve)
GND Ground
NC No Connection (Reserve)
B140XW02 V2 Document Version : 0.3
18 of 29
Product Specification
24
25
26
27
28
29
30
31 VLED_GND LED Ground
32 VLED_GND LED Ground
33 VLED_GND LED Ground
34
35
36
37
38
39
40
NC No Connection (Reserve)
GND Ground–Shield
NC No Connection (Reserve)
NC No Connection (Reserve)
GND Ground–Shield
NC No Connection (Reserve)
NC No Connection (Reserve)
NC No Connection (Reserve)
PWM System PWM Signal Input
LED_EN LED enable pin(+3V Input)
NC No Connection
VLED LED Power Supply 7V-21V
VLED LED Power Supply 7V-21V
VLED LED Power Supply 7V-21V
AU OPTRONICS CORPORATION
www.jxlcd.com
www.jxlcd.com
Signal Pin40
Signal Pin1
Note1: Input signals shall be low or High-impedance state when VDD is off.
B140XW02 V2 Document Version : 0.3
19 of 29
Product Specification
6.4 Interface Timing
6.4.1 Timing Characteristics
Basically, interface timings should match the 1366x768 /60Hz manufacturing guide line timing.
Parameter Symbol Min. Typ. Max. Unit
Frame Rate - - 60 - Hz
AU OPTRONICS CORPORATION
Clock frequency 1/ T
Vertical
Section
Horizontal
Section
Note : DE mode only
6.4.2 Timing diagram
T
CLOCK
DOTCLK
www.jxlcd.com
www.jxlcd.com
Input
Data
DE
DE
Clock
Period TV
Active TVD
Blanking TVB
Period TH
Active THD
Blanking THB
Input Timing Definition ( DE Mode)
Invaild
Data
T
HB
Pixel
1
T
VB
- 72 - MHz
TBD TBD TBD
TBD
TBD TBD TBD
TBD TBD TBD
TBD
TBD TBD TBD
Pixel
2
T
Pixel
3
T
HD
H
T
V
Pixel
N-1
T
Pixel
N
VD
T
Line
T
Clock
Invaild
Data
Pixel
1
B140XW02 V2 Document Version : 0.3
20 of 29
Product Specification
6.5 Power ON/OFF Sequence
Power on/off sequence is as follows. Interface signals and LED on/off sequence are also shown
in the chart. Signals from any system shall be Hi-Z state or low level when VDD is off
AU OPTRONICS CORPORATION
Note:If T3,T5,T6
couldn’t match
above
www.jxlcd.com
www.jxlcd.com
Parameter
T1 0.5 - 10
T2 0 - 50
T3 200 - -
T4 0.5 - 10
T5 10 - -
T6 10 - -
T7 0 - -
T8 10 - -
T9 0 - 10
T10 200 - -
T11 0 - 50
T12 0 - 10
Power Sequence Timing
Value
Min. Typ. Max.
Units
ms
T13 400 - -
specifications, must request T3+T5+T6 > 200ms at least
B140XW02 V2 Document Version : 0.3
21 of 29
7. Panel Reliability Test
7.1 Vibration Test
Test Spec:
Test method: Non-Operation
Acceleration: 1.5 G
Frequency: 10 - 500Hz Random
Sweep: 30 Minutes each Axis (X, Y, Z)
7.2 Shock Test
Test Spec:
Test method: Non-Operation
Acceleration: 220 G , Half sine wave
Product Specification
AU OPTRONICS CORPORATION
Active time: 2 ms
Pulse: X,Y,Z .one time for each side
7.3 Reliability Test
Items
www.jxlcd.com
www.jxlcd.com
Temperature
Humidity Bias
High Temperature
Operation
Low Temperature
Operation
High Temperature
Storage
Low Temperature
Storage
Thermal Shock
Test
Ta= 40
Ta= 50
Ta= 0
Ta= 60
Ta= -20
Ta=-20
℃℃℃℃
Required Condition Note
℃℃℃℃
, 90%RH, 300h
℃℃℃℃
, Dry, 300h
, 300h
℃℃℃℃
, 35%RH, 300h
℃℃℃℃
, 50%RH, 250h
℃℃℃℃
to 60
℃℃℃℃
, Duration at 30 min, 100 cycles
ESD
Note1: According to EN 61000-4-2 , ESD class B: Some performance degradation allowed. No data lost
. Self-recoverable. No hardware failures.
Remark: MTBF (Excluding the LED): 30,000 hours with a confidence level 90%
B140XW02 V2 Document Version : 0.3
Contact : ±8 KV
Air : ±15 KV
Note 1
22 of 29
8. Mechanical Characteristics
8.1 LCM Outline Dimension
www.jxlcd.com
www.jxlcd.com
B140XW02 V2 Document Version : 0.3
23 of 29
www.jxlcd.com
www.jxlcd.com
B140XW02 V2 Document Version : 0.3
24 of 29
9. Shipping and Package
9.1 Shipping Label Format
Week code Model name
H/W
www.jxlcd.com
www.jxlcd.com
B140XW02 V2 Document Version : 0.3
25 of 29
9.2 Carton Package
The outside dimension of carton is 455 (L)mm x 380 (W)mm x 355 (H)mm
9.3 Shipping Package of Palletizing Sequence
www.jxlcd.com
www.jxlcd.com
B140XW02 V2 Document Version : 0.3
26 of 29
10. Appendix: EDID Description
Address
HEX
00 Header 00 00000000 0
01
02
03
04
05
06
07
08 EISA Manuf. Code LSB 06 00000110 6
09 Compressed ASCII AF 10101111 175
0A
0B
0C 32-bit ser # 00 00000000 0
0D
0E
0F
10 Week of manufacture 01 00000001 1
11 Year of manufacture 13 00010011 19
12 EDID Structure Ver. 01 00000001 1
13 EDID revision # 03 00000011 3
14
15
16
17
18
19
1A
1B
1C Red y/ highER 8 bits 57 01010111 87
1D Green x 54 01010100 84
1E Green y 92 10010010 146
1F Blue x 26 00100110 38
20 Blue y 99 10011001 153
21 White x 50 01010000 80
22 White y 54 01010100 84
23 Established timing 1 00 00000000 0
24 Established timing 2 00 00000000 0
25 Established timing 3 00 00000000 0
26 Standard timing #1 01 00000001 1
27
28 Standard timing #2 01 00000001 1
29
2A Standard timing #3 01 00000001 1
2B
Video input def.
www.jxlcd.com
www.jxlcd.com
Max H image size
Max V image size
Display Gamma
Feature support
Red/green low bits (Lower 2:2:2:2 bits)
Blue/white low bits (Lower 2:2:2:2 bits)
FUNCTION Value Value Value
HEX BIN DEC
FF 11111111 255
FF 11111111 255
FF 11111111 255
FF 11111111 255
FF 11111111 255
FF 11111111 255
00 00000000 0
Product Code
hex, LSB first
00 00000000 0
00 00000000 0
00 00000000 0
(digital I/P, non-TMDS, CRGB)
(rounded to cm)
(rounded to cm)
(=(gamma*100)-100)
(no DPMS, Active OFF, RGB, tmg Blk#1)
Red x (Upper 8 bits)
01 00000001 1
01 00000001 1
01 00000001 1
3C 00111100 60
22 00100010 34
80 10000000 128
1F 00011111 31
11 00010001 17
78 01111000 120
0A 00001010 10
C8 11001000 200
A5 10100101 165
9E 10011110 158
B140XW02 V2 Document Version : 0.3
27 of 29
2C Standard timing #4 01 00000001 1
2D
2E Standard timing #5 01 00000001 1
2F
30 Standard timing #6 01 00000001 1
31
32 Standard timing #7 01 00000001 1
33
34 Standard timing #8 01 00000001 1
35
36
Pixel Clock/10000 LSB
37
Pixel Clock/10000 USB
Horz active Lower 8bits
38
Horz blanking Lower 8bits
39
3A
3B
3C
3D
3E
3F
4A
4B
4C
4D
4E
4F
5A Detailed timing/monitor 00 00000000 0
5B descriptor #3 00 00000000 0
5C
B140XW02 V2 Document Version : 0.3
HorzAct:HorzBlnk Upper 4:4 bits
Vertical Active Lower 8bits
Vertical Blanking Lower 8bits
Vert Act : Vertical Blanking (upper 4:4 bit)
HorzSync. Offset
HorzSync.Width
40
41
42
43
44
45
46
47
48 Detailed timing/monitor 00 00000000 0
49 descriptor #2 00 00000000 0
50
51
52
53
54
55
56
57
58
59
VertSync.Offset : VertSync.Width
Horz&Vert Sync Offset/Width Upper 2bits
Horizontal Image Size Lower 8bits
Vertical Image Size Lower 8bits
Horizontal & Vertical Image Size (upper 4:4 bits)
Horizontal Border
www.jxlcd.com
www.jxlcd.com
Vertical Border
Signal
(non-intr, norm, no stero, sep sync, neg pol)
01 00000001 1
01 00000001 1
01 00000001 1
01 00000001 1
01 00000001 1
(zero for internal LCD)
(zero for internal LCD)
00 00000000 0
0F 00001111 15
00 00000000 0
00 00000000 0
00 00000000 0
00 00000000 0
00 00000000 0
00 00000000 0
00 00000000 0
00 00000000 0
00 00000000 0
00 00000000 0
00 00000000 0
00 00000000 0
00 00000000 0
20 00100000 32
00 00000000 0
12 00010010 18
1B 00011011 27
56 01010110 86
46 01000110 70
50 01010000 80
00 00000000 0
23 00100011 35
30 00110000 48
26 00100110 38
16 00010110 22
36 00110110 54
00 00000000 0
35 00110101 53
AD 10101101 173
10 00010000 16
00 00000000 0
00 00000000 0
18 00011000 24
28 of 29
5D
5E
5F Manufacture 41 01000001 65
60 Manufacture 55 01010101 85
61 Manufacture 4F 01001111 79
62
63
64
65
66
67
68
69
6A
6B
6C Detailed timing/monitor 00 00000000 0
6D descriptor #4 00 00000000 0
6E
6F
70
71 Manufacture P/N 42 01000010 66
72 Manufacture P/N 31 00110001 49
73 Manufacture P/N 34 00110100 52
74 Manufacture P/N 30 00110000 48
75 Manufacture P/N 58 01011000 88
76 Manufacture P/N 57 01010111 87
77 Manufacture P/N 30 00110000 48
78 Manufacture P/N 32 00110010 50
79 Manufacture P/N 20 00100000 32
7A Manufacture P/N 56 01010110 86
7B Manufacture P/N 32 00110010 50
7C
7D
7E Extension Flag 00 00000000 0
7F Checksum 12 00010010 18
www.jxlcd.com
www.jxlcd.com
FE 11111110 254
00 00000000 0
0A 00001010 10
20 00100000 32
20 00100000 32
20 00100000 32
20 00100000 32
20 00100000 32
20 00100000 32
20 00100000 32
20 00100000 32
20 00100000 32
00 00000000 0
FE 11111110 254
00 00000000 0
20 00100000 32
0A 00001010 10
SUM 5888
SUM to
HEX 1700
B140XW02 V2 Document Version : 0.3
29 of 29
Loading...