AU Optronics B133EW05-V0 Product Specification

AUO
) Preliminary Specifications
( V ( ) Final Specifications
Product Specification
AU OPTRONICS CORPORATION
Module
Model Name
Customer Date
www.jxlcd.com
Checked &
Approved by
www.jxlcd.com
13.3” WXGA Color TFT-LCD
B133EW05 V0
Date
Approved by Date
Kendra Wang 2/1/2008
Prepared by Date
Note: This Specification is subject to change without notice.
NBBU spec. Template 1.0
Chih Chen Wu 2/1/2008
NBBU Marketing Division /
AU Optronics corporation
1 of 32
Product Specification
AUO
AU OPTRONICS CORPORATION
Contents
1. Handling Precautions .............................................................. 4
2. General Description ................................................................ 5
2.1 General Specification ..........................................................................................................................5
2.2 Optical Characteristics ........................................................................................................................6
3. Functional Block Diagram ..................................................... 11
4. Absolute Maximum Ratings................................................... 12
4.1 Absolute Ratings of TFT LCD Module.............................................................................................12
4.2 Absolute Ratings of Backlight Unit...................................................................................................12
4.3 Absolute Ratings of Environment .....................................................................................................12
5. Electrical characteristics ....................................................... 13
5.1 TFT LCD Module..............................................................................................................................13
5.2 Backlight Unit ...................................................................................................................................15
6. Signal Characteristic ............................................................. 16
6.1 Pixel Format Image ...........................................................................................................................16
6.2 The input data format ........................................................................................................................17
6.3 Signal Description/Pin Assignment...................................................................................................18
6.4 Interface Timing ................................................................................................................................19
7. Connector Description........................................................... 22
7.1 TFT LCD Module..............................................................................................................................22
www.jxlcd.com
8. Dynamic Test ........................................................................ 23
8.1 Vibration Test ....................................................................................................................................23
8.2 Shock Test Spec:................................................................................................................................23
www.jxlcd.com
9. Reliability.............................................................................. 24
10. Mechanical Characteristics.................................................. 25
10.1 LCM Outline Dimension.................................................................................................................25
11. Shipping and Package ......................................................... 27
11.1 Shipping Label Format ....................................................................................................................27
11.2 Carton package ................................................................................................................................28
11.3 Shipping package of palletizing sequence.......................................................................................28
12. Appendix: EDID description ................................................ 29
NBBU spec. Template 1.0
2 of 32
Product Specification
AUO
AU OPTRONICS CORPORATION
Record of Revision
Version and Date Page
0.1 2007/12/14 All First Edition for Customer
0.2 2007/12/24 27 11.1 Shipping Label Format 11.1 Shipping Label Format
0.3 2008/01/16 18 Pin11: 5V , Pin12: GND Pin11: GND , Pin12: NC
29-32 EDID check sum 34 EDID check sum 7E
0.4 2008/02/01 5 Physical Size: T 3.05 Physical Size: T 3.35
26 Label position on rear frame Label position on BLU sheet
28 TBD Add Carton and shipping Packing
0.5 2008/03/25 5
www.jxlcd.com
www.jxlcd.com
I
LED
=19mA
Old description New Description Remark
I
LED
=20mA
NBBU spec. Template 1.0
3 of 32
Product Specification
AUO
1. Handling Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth when handling.
7) Do not open nor modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) In case if a Module has to be put back into the packing container slot after once it was taken out from the container, do not press the center of the LED lamp Reflector edge.
AU OPTRONICS CORPORATION
Instead, press at the far ends of the LED lamp Reflector edge softly. Otherwise the TFT Module may be damaged.
10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the Interface Connector of the TFT Module.
11) After installation of the TFT Module into an enclosure (Notebook PC Bezel, for example), do not twist nor bend the TFT Module even momentary. At designing the enclosure, it should be taken into consideration that no bending/twisting forces are applied to the TFT Module from outside. Otherwise the TFT Module may be damaged.
12) Small amount of materials having no flammability grade is used in the LCD module. The LCD module should be supplied by power complied with requirements of Limited Power Source (IEC60950 or UL1950), or be applied exemption.
13) The LCD module is designed so that the LED in it is supplied by Limited Current Circuit (IEC60950 or UL1950). Do not connect the LED in Hazardous Voltage Circuit.
www.jxlcd.com
www.jxlcd.com
NBBU spec. Template 1.0
4 of 32
Product Specification
AUO
(Note1)
2. General Description
B133EW05 V0 is a Color Active Matrix Liquid Crystal Display composed of a TFT LCD panel, a driver circuit, and backlight system. The screen format is intended to support the WXGA (1280(H) x 800(V)) screen and 262k colors (RGB 6-bits data driver) without backlight inverter. All input signals are LVDS interface compatible.
B133EW05 V0 is designed for a display unit of notebook style personal computer and industrial machine.
AU OPTRONICS CORPORATION
2.1 General Specification
The following items are characteristics summary on the table at 25 condition:
Items Unit Specifications
Screen Diagonal [mm] 337.8 (13.3W”)
Active Area [mm] 286.08 (H) X 178.8 (V)
Pixels H x V 1280x3(RGB) x 800
Pixel Pitch [mm] 0.2235 x 0.2235
Pixel Format R.G.B. Vertical Stripe
Display Mode Normally White
White Luminance (I Note: I
Luminance Uniformity 1.25 max. (5 points)
Contrast Ratio 600 typ
www.jxlcd.com
LED
www.jxlcd.com
is lamp current
LED
=20mA)
[cd/m2] 300 typ.(5 points average)
240 min.(5 points average)
Response Time [ms] 16 typ
Nominal Input Voltage VDD [Volt] +3.3 typ.
Power Consumption [Watt] 4.85 max.
Weight [Grams] 245 max. Physical Size
Electrical Interface one channel LVDS
Surface Treatment Anti-Glare, Hardness 3H,
NBBU spec. Template 1.0
[mm]
L W T
Max 296.5 203.0 3.35
Typical -
Min -
5 of 32
Product Specification
AUO
RoHS Compliance
Support Color 262K colors ( RGB 6-bit )
AU OPTRONICS CORPORATION
Temperature Range
Operating Storage (Non-Operating)
RoHS Compliance
[oC] [oC]
0 to +50
-25 to +65
2.2 Optical Characteristics
The optical characteristics are measured under stable conditions at 25 (Room Temperature) :
Item Unit Conditions Min. Typ. Max. Note
White Luminance
I
LED
=20mA
Viewing Angle
Luminance
Uniformity
Luminance
Uniformity
CR: Contrast Ratio
Cross talk %
Response Time
Chromaticity of color
Coordinates
(CIE 1931)
www.jxlcd.com
www.jxlcd.com
NTSC %
[cd/m2]
[degree] [degree]
[degree] [degree]
[msec] Rising
[msec] Falling
[msec] Rising + Falling
5 points average
Horizontal
(Right)
CR = 10 (Left)
Vertical
(Upper)
CR = 10 (Lower)
5 Points
13 Points
400 600 - 6
4 7
Red x
Red y
Green x
Green y
Blue x
Blue y
White x
White y
CIE 1931
240 300 -
40
40
15
30
- - 1.25 1
- - 1.6 2
-
- 12 17
- 16 25
0.570 0.600 0.630
0.315 0.345 0.375
0.290 0.320 0.350
0.525 0.555 0.585
0.120 0.150 0.180
0.090 0.120 0.150
0.283 0.313 0.343
0.299 0.329 0.359
- 45 -
45 45
15 35
4
1, 4,
5.
-
-
8
-
-
8
8
2,8
NBBU spec. Template 1.0
6 of 32
Product Specification
AUO
=
Maximum Brightness of thirteen points
Minimum Brightness of thirteen points
Maximum Brightness of five
points
=
Minimum Brightness of five points
Note 1: 5 points position (Ref: Active area)
H /4
H /4
AU OPTRONICS CORPORATION
W / 4 W / 4 W / 4 W /4
W
1 2
H
H /4
H /4
Note 2: 13 points position (Ref: Active area)
W /4
1 0
1 0
H /4
www.jxlcd.com
www.jxlcd.com
H /4
H
H /4
1
6
3
4
W
W /4
4 5
W /4
2
7
5
W /4
1 0
3
8
9
H /4
1 0
1 1
1 2
Note 3: The luminance uniformity of 5 or13 points is defined by dividing the maximum luminance values by the minimum test point luminance
δ
W5
1 0
1 3
δ
Note 4: Measurement method
NBBU spec. Template 1.0
W13
7 of 32
Product Specification
AUO
Field=2
°
Contrast ratio (CR)=
Brightness on the “White” state
Brightness on the “Black” state
The LCD module should be stabilized at given temperature for 30 minutes to avoid abrupt temperature change
during measuring. In order to stabilize the luminance, the measurement should be executed after lighting Backlight
for 30 minutes in a stable, windless and dark room.
AU OPTRONICS CORPORATION
Photo detector
Note 5 Definition of Average Luminance of White (YL):
Measure the luminance of gray level 63 at 5 pointsY
L (x) is corresponding to the luminance of the point X at Figure in Note (1).
Note 6 Definition of contrast ratio:
Note 7 Definition of Cross Talk (CT)
www.jxlcd.com
www.jxlcd.com
= [L (1)+ L (2)+ L (3)+ L (4)+ L (5)] / 5
L
Contrast ratio is calculated with the following formula.
CT = | YB – YA | / YA × 100 (%)
Where
YA = Luminance of measured location without gray level 0 pattern (cd/m2)
NBBU spec. Template 1.0
8 of 32
Product Specification
AUO
YB = Luminance of measured location with gray level 0 pattern (cd/m2)
Note 8: Definition of response time:
The output signals of BM-7 or equivalent are measured when the input signals are changed from “Black” to
“White” (falling time) and from “White” to “Black” (rising time), respectively. The response time interval between the
10% and 90% of amplitudes. Refer to figure as below.
AU OPTRONICS CORPORATION
"Black"
100%
S i
90%
g n a l
(
R e
l
a t
i
v e
v a l
u e )
www.jxlcd.com
www.jxlcd.com
10%
0%
Tr
Tf
"White""White"
NBBU spec. Template 1.0
9 of 32
Product Specification
AUO
Note 8. Definition of viewing angle
Viewing angle is the measurement of contrast ratio 10, at the screen center, over a 180° horizontal and
180° vertical range (off-normal viewing angles). The 180° viewing angle range is broken down as follows; 90° (θ)
horizontal left and right and 90° (Φ) vertical, high (up) and low (down). The measurement direction is typically
perpendicular to the display surface with the screen rotated about its center to develop the desired measurement
viewing angle.
AU OPTRONICS CORPORATION
www.jxlcd.com
www.jxlcd.com
NBBU spec. Template 1.0
10 of 32
Product Specification
AUO
3. Functional Block Diagram
The following diagram shows the functional block of the 15.4 inches wide Color TFT/LCD Module:
AU OPTRONICS CORPORATION
www.jxlcd.com
www.jxlcd.com
NBBU spec. Template 1.0
11 of 32
Product Specification
AUO
4. Absolute Maximum Ratings
An absolute maximum rating of the module is as following:
4.1 Absolute Ratings of TFT LCD Module
Item Symbol Min Max Unit Conditions
AU OPTRONICS CORPORATION
Logic/LCD Drive Voltage
Vin -0.3 +4.0 [Volt] Note 1,2
4.2 Absolute Ratings of Backlight Unit
Item Symbol Min Max Unit Conditions
LED Current ILED - 35 [mA] rms Note 1,2
4.3 Absolute Ratings of Environment
Item Symbol Min Max Unit Conditions
Operating Temperature
Operation Humidity HOP 5 95 [%RH] Note 3
Storage Temperature
Storage Humidity HST
Note 1: At Ta (25 )
Note 2: Permanent damage to the device may occur if exceed maximum values
Note 3: For quality performance, please refer to AUO IIS (Incoming Inspection Standard).
www.jxlcd.com
www.jxlcd.com
TOP 0 +50 [oC] Note 3
TST -20 +60 [oC] Note 3
5 95
Twb=39°C
[%RH]
Note 3
Operating Range
NBBU spec. Template 1.0
Storage Range
12 of 32
Product Specification
AUO
-
90%
10%
5. Electrical characteristics
5.1 TFT LCD Module
5.1.1 Power Specification
Input power specifications are as follows;
AU OPTRONICS CORPORATION
Symble Parameter Min Typ Max Units
VDD Logic/LCD Drive
PDD VDD Power IDD IDD Current
I
Rush
Inrush Current
VDDrp Allowable
Logic/LCD Drive Ripple Voltage
Note 1 : Maximum Measurement ConditionBlack Pattern
Note 2Typical Measurement Condition: Mosaic Pattern
Note 3Measure Condition
www.jxlcd.com
www.jxlcd.com
3.0 3.3 3.6 [Volt]
0.75 0.85 [Watt] Note 1/2
- 230
- 0.7
- -
290
1.5
100
[mA]
[A]
[mV] p-p
Note
Note 1/2
Note 3
3.3V
0V
0.5ms
Vin rising time
NBBU spec. Template 1.0
13 of 32
Product Specification
AUO
5.1.2 Signal Electrical Characteristics
Input signals shall be low or High-impedance state when VDD is off.
Signal electrical characteristics are as follows;
AU OPTRONICS CORPORATION
Parameter
Vth
Vtl
Vcm
Note: LVDS Signal Waveform
Differential Input High Threshold (Vcm=+1.2V)
Differential Input Low Threshold (Vcm=+1.2V)
Common Mode Voltage
www.jxlcd.com
www.jxlcd.com
Condition Min Max Unit
Differential Input
-
-100
0.8
+100
-
2.0
[mV]
[mV]
[V]
NBBU spec. Template 1.0
14 of 32
AUO
5.2 Backlight Unit
Parameter guideline for LED
Parameter Min Typ Maz Units Units
White Luminance 5
points average
Product Specification
AU OPTRONICS CORPORATION
240 300 - [cd/m2] Ta=25 oC
LED current (ILED)
LED Power
consumption
Light bar PIN assignment:
www.jxlcd.com
PIN NO. Pin assignment Function
1 VOUT LED Anode (Positive)
www.jxlcd.com
- 20 - [mA] Ta=25 oC
-
4.07
- [Watt] Ta=25 oC
2 VOUT LED Anode (Positive)
3 VOUT LED Anode (Positive)
4 NC NC
5 FB1 LED Cathode (Negative)
6 FB2 LED Cathode (Negative)
7 FB3 LED Cathode (Negative)
8 FB4 LED Cathode (Negative)
9 FB5 LED Cathode (Negative)
10 FB6 LED Cathode (Negative)
NBBU spec. Template 1.0
15 of 32
Product Specification
AUO
6. Signal Characteristic
6.1 Pixel Format Image
Following figure shows the relationship of the input signals and LCD pixel format.
AU OPTRONICS CORPORATION
www.jxlcd.com
www.jxlcd.com
NBBU spec. Template 1.0
16 of 32
Product Specification
AUO
6.2 The input data format
Signal Name
VEEDID (3.3V) +3.3V EDID Power
CLK EEDID EDID Clock Input
AU OPTRONICS CORPORATION
Description
DATA EEDID EDID Data Input
RXIN0-, RXIN0+
RXIN1-, RXIN1+
RXIN2-, RXIN2+
RXCLKIN-, RXCLKIN+
VDD
VSS
Note: Output signals from any system shall be low or High-impedance state when VDD is off.
www.jxlcd.com
www.jxlcd.com
LVDS differential data input(Red0-Red5, Green0)
LVDS differential data input(Green1-Green5, Blue0-Blue1)
LVDS differential data input(Blue2-Blue5, Hsync, Vsync, DE)
LVDS differential clock input
+3.3V Power Supply
Ground
NBBU spec. Template 1.0
17 of 32
Product Specification
AUO
6.3 Signal Description/Pin Assignment
LVDS is a differential signal technology for LCD interface and high speed data transfer device.
Pin Signal Description
1 VSS Ground 2 CONNTST Connector test 3 VDD Logic power 3.3V (Panel logic, BL logic) 4 VDD Logic power 3.3V (Panel logic, BL logic) 5 VDD Logic power 3.3V (Panel logic, BL logic) 6 VEDID EDID 3.3V power 7 TEST Panel Self Test 8 CLK EDID clock
9 DATA EDID data 10 VSS Ground 11 VSS Ground 12 NC no connection 13 RIN0- - LVDS differential data input (R0-R5, G0) 14 RIN0+ + LVDS differential data input (R0-R5, G0) 15 VSS Ground 16 RIN1- - LVDS differential data input (G1-G5, B0-B1) 17 RIN1+ + LVDS differential data input (G1-G5, B0-B1) 18 VSS Ground 19 RIN2- - LVDS differential data input (B2-B5,HS,VS, DE) 20 RIN2+ + LVDS differential data input (B2-B5,HS,VS, DE) 21 VSS Ground 22 CLK- - LVDS differential clock input 23 CLK+ + LVDS differential clock input 24 VSS Ground 25 INV_PWM PWM brightness control 26 VBL- LED power return 27 VBL- LED power return 28 VBL- LED power return 29 VBL- LED power return 30 VBL- LED power return 31 NC no connection 32 VBL+ 7V - 20V LED power source 33 VBL+ 7V - 20V LED power source 34 VBL+ 7V - 20V LED power source 35 VBL+ 7V - 20V LED power source 36 VBL+ 7V - 20V LED power source 37 CONNTST Connector test 38 SMB_CLK SMBus Clock 39 SMB_DAT SMBus Data 40 VSS Ground
www.jxlcd.com
www.jxlcd.com
AU OPTRONICS CORPORATION
Note1: Start from right side
NBBU spec. Template 1.0
18 of 32
Product Specification
AUO
6.4 Interface Timing
6.4.1 Timing Characteristics
Basically, interface timings should match the 1280x800 /60Hz manufacturing guide line timing.
Parameter Symbol Min. Typ. Max. Unit
Frame Rate - 50 60 - Hz
AU OPTRONICS CORPORATION
Clock frequency 1/ T
Vertical
Section
Horizontal
Section
Note : DE mode only
www.jxlcd.com
www.jxlcd.com
Period TV 808 816 1023
Active TVD 800
Blanking TVB 8 16 -
Period TH 1320 1408 2047
Active THD 1280
Blanking THB 30 128
- 68.9 72 MHz
Clock
T
T
Line
Clock
NBBU spec. Template 1.0
19 of 32
AUO
6.4.2 Timing diagram
Product Specification
AU OPTRONICS CORPORATION
www.jxlcd.com
www.jxlcd.com
NBBU spec. Template 1.0
20 of 32
Product Specification
AUO
T3 T2
T1
T7
6.5 Power ON/OFF Sequence
VDD power and lamp on/off sequence is as follows. Interface signals are also shown in the chart. Signals from any system shall be Hi-Z state or low level when VDD is off.
Power Supply VDD
Backlight On
www.jxlcd.com
www.jxlcd.com
Power Sequence Timing
Parameter
AU OPTRONICS CORPORATION
90%
10%
T5
Value
Min.
T1
T2
T3
T4
T5
T6
0.5
5
0.5
400
200
200
Typ.
-
-
-
-
-
-
VALID DATA
Max.
10
50
50
-
-
-
90%
10%
T4
T6
Units
(ms)
(ms)
(ms)
(ms)
(ms)
(ms)
T7
NBBU spec. Template 1.0
0
-
10
(ms)
21 of 32
Product Specification
AUO
7. Connector Description
Physical interface is described as for the connector on module.
These connectors are capable of accommodating the following signals and will be following components.
7.1 TFT LCD Module
AU OPTRONICS CORPORATION
Connector Name / Designation
Manufacturer IPEX or compatible
Type / Part Number
Mating Housing/Part Number
www.jxlcd.com
www.jxlcd.com
For Signal Connector
20347-340E-12
20346-040T-02 or compatible
or compatible
NBBU spec. Template 1.0
22 of 32
Product Specification
AUO
8. Dynamic Test
8.1 Vibration Test Test condition(Non-OP):
Acceleration: 1.3 G
Frequency: 10 - 500Hz Random
Sweep: 30 Minutes each Axis (X, Y, Z)
8.2 Shock Test Spec: Test condition(Non-OP):
Acceleration: 220 G , Half sine wave
Active time: 2 ms
Pulse: +/-X,+/-Y,+/-Z , one time for each side
AU OPTRONICS CORPORATION
Remark:
1. Ambient condition is 25 + 5℃, Relative humidity : 40% ~ 70%
2. Non-packaged and Non-operation
www.jxlcd.com
www.jxlcd.com
NBBU spec. Template 1.0
23 of 32
AUO
9. Reliability
Items
Product Specification
AU OPTRONICS CORPORATION
Required Condition Note
Temperature
Humidity Bias
High Temperature
Operation
Low Temperature
Operation
High Temperature
Storage
Low Temperature
Storage
Thermal Shock
Test
ESD
www.jxlcd.com
www.jxlcd.com
Ta= 40℃℃, 95%RH, 250h
Ta= 50℃℃, Dry, 250h
Ta= 0℃℃, 250h
Ta= 65℃℃/20%, 250h
Ta= -25℃℃, 50%RH, 250h
Ta=-40℃℃to 65℃℃℃℃, Duration at 30 min, 50 cycles
Contact : ±8 KV
Air : ±15 KV
Note 1
Note1: According to EN 61000-4-2 , ESD class B: Some performance degradation allowed. No data lost
. Self-recoverable. No hardware failures.
Remark: MTBF (Excluding the LED): 30,000 hours with a confidence level 90%
NBBU spec. Template 1.0
24 of 32
Product Specification
AUO
10. Mechanical Characteristics
10.1 LCM Outline Dimension
AU OPTRONICS CORPORATION
www.jxlcd.com
www.jxlcd.com
NBBU spec. Template 1.0
25 of 32
Product Specification
AUO
AU OPTRONICS CORPORATION
www.jxlcd.com
www.jxlcd.com
NBBU spec. Template 1.0
26 of 32
Product Specification
AUO
MADE IN TAIWAN (M1)
0
FM736
AU OPTRONICS CORPORATION
11. Shipping and Package
11.1 Shipping Label Format
11.1 Shipping Label Format
TW -0FM736-54321-
932-0123-YYY
Made In
China
DP/N
Manufactured 05/52
Model No: B133EW05 V0
AU Optronics 0AXXG
H/W: 0A F/W:1
www.jxlcd.com
www.jxlcd.com
NBBU spec. Template 1.0
27 of 32
AUO
11.2 Carton package
Product Specification
AU OPTRONICS CORPORATION
www.jxlcd.com
11.3 Shipping package of palletizing sequence
www.jxlcd.com
NBBU spec. Template 1.0
28 of 32
Product Specification
AUO
12. Appendix: EDID description
AU OPTRONICS CORPORATION
Address
HEX HEX
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
20
21
22
23
24
25
26
www.jxlcd.com
www.jxlcd.com
Video input def. (digital I/P, non-TMDS, CRGB)
Max H image size (rounded to cm)
Max V image size (rounded to cm)
Display Gamma (=(gamma*100)-100)
Feature support (no DPMS, Active OFF, RGB, tmg Blk#1)
Red/green low bits (Lower 2:2:2:2 bits)
Blue/white low bits (Lower 2:2:2:2 bits)
FUNCTION Value
Header 00 00000000 0
FF 11111111 255
FF 11111111 255
FF 11111111 255
FF 11111111 255
FF 11111111 255
FF 11111111 255
00 00000000 0
EISA Manuf. Code LSB 06 00000110 6
Compressed ASCII AF 10101111 175
Product Code
hex, LSB first
32-bit ser # 00 00000000 0
00 00000000 0
00 00000000 0
00 00000000 0
Week of manufacture 01 00000001 1
Year of manufacture 12 00010010 18
EDID Structure Ver. 01 00000001 1
EDID revision # 03 00000011 3
Red x (Upper 8 bits)
Red y/ highER 8 bits 58 01011000 88
Green x 52 01010010 82
Green y 8E 10001110 142
Blue x 26 00100110 38
Blue y 1E 00011110 30
White x 50 01010000 80
White y 54 01010100 84
Established timing 1 00 00000000 0
Established timing 2 00 00000000 0
Established timing 3 00 00000000 0
Standard timing #1 01 00000001 1
Value Value Note
BIN DEC
24 00100100 36
50 01010000 80
80 10000000 128
1D 00011101 29
12 00010010 18
78 01111000 120
0A 00001010 10
90 10010000 144
B5 10110101 181
99 10011001 153
NBBU spec. Template 1.0
29 of 32
Product Specification
AUO
27
28
29
2A
2B
2C
2D
2E
2F
30
31
32
33
34
35
36
37
38
39
3A
3B
3C
3D
3E
3F
40
41
42
43
44
45
46
47
48
49
4A
4B
4C
4D
4E
4F
50
51
NBBU spec. Template 1.0
www.jxlcd.com
www.jxlcd.com
Signal (non-intr, norm, no stero, sep sync, neg pol)
HorzAct:HorzBlnk Upper 4:4 bits
Vertical Blanking Lower 8bits
Vert Act : Vertical Blanking (upper 4:4 bit)
VertSync.Offset : VertSync.Width
Horz&Vert Sync Offset/Width Upper 2bits
Horizontal Image Size Lower 8bits
Horizontal & Vertical Image Size (upper 4:4 bits)
Horizontal Border (zero for internal LCD)
Vertical Border (zero for internal LCD)
AU OPTRONICS CORPORATION
01 00000001 1
Standard timing #2 01 00000001 1
01 00000001 1
Standard timing #3 01 00000001 1
01 00000001 1
Standard timing #4 01 00000001 1
01 00000001 1
Standard timing #5 01 00000001 1
01 00000001 1
Standard timing #6 01 00000001 1
01 00000001 1
Standard timing #7 01 00000001 1
01 00000001 1
Standard timing #8 01 00000001 1
01 00000001 1
Pixel Clock/10000 LSB
Pixel Clock/10000 USB
Horz active Lower 8bits
Horz blanking Lower 8bits
Vertical Active Lower 8bits
HorzSync. Offset
HorzSync.Width
Vertical Image Size Lower 8bits
Detailed timing/monitor 00 00000000 0
descriptor #2 00 00000000 0
00 00000000 0
0F 00001111 15
00 00000000 0
00 00000000 0
00 00000000 0
00 00000000 0
00 00000000 0
00 00000000 0
12 00010010 18
1B 00011011 27
00 00000000 0
87 10000111 135
50 01010000 80
20 00100000 32
10 00010000 16
30 00110000 48
30 00110000 48
20 00100000 32
36 00110110 54
00 00000000 0
1E 00011110 30
B2 10110010 178
10 00010000 16
00 00000000 0
00 00000000 0
18 00011000 24
30 of 32
Product Specification
AUO
52
53
54
55
56
57
58
59
5A
5B
5C
5D
5E
5F
60
61
62
63
64
65
66
67
68
69
6A
6B
6C
6D
6E
6F
70
71
72
73
74
75
76
77
78
79
7A
7B
7C
NBBU spec. Template 1.0
www.jxlcd.com
www.jxlcd.com
AU OPTRONICS CORPORATION
00 00000000 0
00 00000000 0
00 00000000 0
00 00000000 0
00 00000000 0
00 00000000 0
00 00000000 0
20 00100000 32
Detailed timing/monitor 00 00000000 0
descriptor #3 00 00000000 0
00 00000000 0
FE 11111110 254
00 00000000 0
Manufacture 41 01000001 65 A
Manufacture 55 01010101 85 U
Manufacture 4F 01001111 79 O
0A 00001010 10
20 00100000 32
20 00100000 32
20 00100000 32
20 00100000 32
20 00100000 32
20 00100000 32
20 00100000 32
20 00100000 32
20 00100000 32
Detailed timing/monitor 00 00000000 0
descriptor #4 00 00000000 0
00 00000000 0
FE 11111110 254
00 00000000 0
Manufacture P/N 42 01000010 66 B
Manufacture P/N 31 00110001 49 1
Manufacture P/N 33 00110011 51 3
Manufacture P/N 33 00110011 51 3
Manufacture P/N 45 01000101 69 E
Manufacture P/N 57 01010111 87 W
Manufacture P/N 30 00110000 48 0
Manufacture P/N 35 00110101 53 5
Manufacture P/N 20 00100000 32
Manufacture P/N 56 01010110 86 V
Manufacture P/N 30 00110000 48 0
20 00100000 32
31 of 32
Product Specification
AUO
7D
7E
7F
SUM
SUM to HEX
AU OPTRONICS CORPORATION
0A 00001010 10
Extension Flag 00 00000000 0
Checksum C1 11000001 193
5888 1700
www.jxlcd.com
www.jxlcd.com
NBBU spec. Template 1.0
32 of 32
Loading...