AU Optronics B116XW01-V0 Product Specification

Product Specification

) Preliminary Specifications

( V ( ) Final Specifications

Module 11.6”(11.57”) HD Color TFT-LCD with LED Backlight design

AU OPTRONICS CORPORATION

Model Name

Note ( )

Customer Date

www.jxlcd.com

Checked &

Approved by

B116XW01 V0 (H/W:0A)

LED Backlight with driving circuit design

Date

Approved by Date

xxxxxxx

Prepared by

MM/DD/YYYY

Note: This Specification is subject to change without notice.

Winni Chen

NBBU Marketing Division /

AU Optronics corporation

03/16/2009

B116XW01 V0 Document Version : 0.4

1 of 37

Product Specification

AU OPTRONICS CORPORATION

Contents

1. Handling Precautions .............................................................. 4

2. General Description ................................................................ 5

2.1 General Specification ..........................................................................................................................5

2.2 Optical Characteristics ........................................................................................................................6

3. Functional Block Diagram ..................................................... 11

4. Absolute Maximum Ratings................................................... 12

4.1 Absolute Ratings of TFT LCD Module.............................................................................................12

4.2 Absolute Ratings of Environment .....................................................................................................12

5. Electrical characteristics ....................................................... 13

5.1 TFT LCD Module..............................................................................................................................13

5.2 Backlight Unit ...................................................................................................................................15

6. Signal Characteristic ............................................................. 16

6.1 Pixel Format Image ...........................................................................................................................16

6.2 The input data format ........................................................................................................................17

6.3 Integration Interface and Pin Assignment..........................................................................................18

6.4 Interface Timing ................................................................................................................................22

7. Connector Description........................................................... 25

7.1 TFT LCD Module..............................................................................................................................25

8. LED Driving Specification ...................................................... 26

www.jxlcd.com

8.1 Connector Description.......................................................................................................................26

8.2 Pin Assignment..................................................................................................................................26

www.jxlcd.com

9. Vibration and Shock Test ...................................................... 27

9.1 Vibration Test ....................................................................................................................................27

9.2 Shock Test Spec:................................................................................................................................27

10. Reliability............................................................................ 28

11. Mechanical Characteristics.................................................. 29

11.1 LCM Outline Dimension.................................................................................................................29

11.2 Screw Hole Depth and Center Position ....................................................... 錯誤

錯誤! 尚未定義書籤

錯誤錯誤

尚未定義書籤。。。。

尚未定義書籤尚未定義書籤

12. Shipping and Package ......................................................... 31

12.1 Shipping Label Format....................................................................................................................31

12.2 Carton package................................................................................................................................32

12.3 Shipping package of palletizing sequence.......................................................................................33

13. Appendix: EDID description ................................................ 34

B116XW01 V0 Document Version : 0.4

2 of 37

Product Specification

AU OPTRONICS CORPORATION

Record of Revision

Version and Date Page

0.1 2009/01/07 All First Edition for Customer

0.2 2009/02/13 13 VDD Power:1.6W (max) VDD Power:0.8W (max) modified

29,

20

0.3 2009/03/05 5 Physical Size

19 LED enable pin(+3V Input) LED enable pin(+3.3±0.3V Input) modified

13 IDD Current Specification

0.4 2009/03/16 6 Response Time

15 LED Power Consumption

www.jxlcd.com

22 Timing Charateristics: TBD Timing Charateristics: Updated Updated

LCM Outline Dimension:

30

Y diemension is 173mm version.

LVDS Connector Postion:90.38 LVDS Connector Postion:99.2 modified

30

Min. Typ. Max.

Length 274.5 275.0 275.5

Width 171.0 172.0 173.0

Symble Typ Max

Rising: TBD(typ), TBD(max)

Falling: TBD(typ), TBD(max)

Typ Max Uni t

LED Power consumption

Old description New Description Remark

LCM Outline Dimension:

Y dimension shorter.

Physical Size

Min. Typ. Max.

Length 277.5 278 278.5

Width 166 167 168

IDD Current Specification

Symble Typ Max

IDD 350 450

TBD TBD W alt

IDD 242 267

Response Time

Rising: 6ms(typ), 8ms(max)

Falling: 2ms(typ), 4m s(m ax)

LED Power Consumption

Typ Max Unit

LED Power consumption

3.01 3. 06 W alt

modified

typo

Updated

31

32 Carton package:TBD Carton package:Added

33

6

B116XW01 V0 Document Version : 0.4

Shipping Label Format: TBD Shipping Label Format: Added Updated

Updated

Shipping package of palletizing sequence:TBD

Color / Chromaticity Coodinates: TBD Color / Chromaticity Coodinates: Added

Shipping package of palletizing sequence: Added

Updated

3 of 37

Product Specification

1. Handling Precautions

1) Since front polarizer is easily damaged, pay attention not to scratch it.

2) Be sure to turn off power supply when inserting or disconnecting from input connector.

3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.

4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.

5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.

6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth when handling.

7) Do not open nor modify the Module Assembly.

8) Do not press the reflector sheet at the back of the module to any directions.

9) At the insertion or removal of the Signal Interface Connector, be sure not to rotate

AU OPTRONICS CORPORATION

nor tilt the Interface Connector of the TFT Module.

11) After installation of the TFT Module into an enclosure (Notebook PC Bezel, for example), do not twist nor bend the TFT Module even momentary. At designing the enclosure, it should be taken into consideration that no bending/twisting forces are applied to the TFT Module from outside. Otherwise the TFT Module may be damaged.

12) Small amount of materials having no flammability grade is used in the LCD module. The LCD module should be supplied by power complied with requirements of Limited Power Source (IEC60950 or UL1950), or be applied exemption.

13) Disconnecting power supply before handling LCD modules, it can prevent electric shock, DO NOT TOUCH the electrode parts, cables, connectors and LED circuit part of TFT module that a LED light bar build in as a light source of back light unit. It can prevent electrostic breakdown.

www.jxlcd.com

B116XW01 V0 Document Version : 0.4

4 of 37

Product Specification

Thickness

2. General Description

B116XW01 V0 is a Color Active Matrix Liquid Crystal Display composed of a TFT LCD panel, a driver circuit, and LED backlight system. The screen format is intended to support the HD (1366(H) x 768(V)) screen and 262k colors (RGB 6-bits data driver) with LED backlight driving circuit. All input signals are LVDS interface compatible.

B116XW01 V0 is designed for a display unit of notebook style personal computer and industrial machine.

AU OPTRONICS CORPORATION

2.1 General Specification

The following items are characteristics summary on the table at 25 ℃ condition:

Items Unit Specifications

Screen Diagonal [mm] 11.6W” (11.57”W)

Active Area [mm] 256.125 X 144.0

Pixels H x V 1366x3(RGB) x 768

Pixel Pitch [mm] 0.1875 x 0.1875

Pixel Format R.G.B. Vertical Stripe

Display Mode Normally White

www.jxlcd.com

White Luminance (I

(Note: ILED is LED current)

Luminance Uniformity 1.25 max. (5 points) Contrast Ratio 500:1 typ Response Time [ms] 8 typ / 12 Max

www.jxlcd.com

LED

=20mA)

[cd/m2] 200 typ. (5 points average)

170 min. (5 points average)

Nominal Input Voltage VDD [Volt] +3.3 typ.

Power Consumption [Watt] 3.86 max. (Include Logic and Blu power)

Weight [Grams] 235g max. Physical Size without inverter,

with bracket.

Electrical Interface 1 channel LVDS

Glass Thickness [mm] 0.5

Surface Treatment Glare, Hardness 3H,

Support Color 262K colors ( RGB 6-bit )

B116XW01 V0 Document Version : 0.4

[mm]

Min. Typ. Max.

Length 277.5 278 278.5

Width 166 167 168

- - 3.6

Reflection <4%

5 of 37

Product Specification

mpliance

Temperature Range

Operating Storage (Non-Operating)

RoHS Compliance RoHS Co

2.2 Optical Characteristics

The optical characteristics are measured under stable conditions at 25℃ (Room Temperature) :

AU OPTRONICS CORPORATION

[oC] [oC]

0 to +50

-20 to +60

Item Symbol

White Luminance

I

LED

=20mA

Viewing Angle

Luminance

Uniformity

Luminance

Uniformity

Contrast Ratio CR

Cross talk %

Response Time

Color /

Chromaticity

Coodinates

www.jxlcd.com

Red

Green

Blue

White

Conditions Min. Typ. Max. Unit Note

θθθθR θθθθL

ψψψψH ψψψψL

δδδδ5P

δδδδ

13P

Tr Rising

Tf Falling

TRT Rising + Falling

Rx

Ry

Gx

Gy

Bx

By

Wx

Wy

5 points average

Horizontal (Right)

CR = 10 (Left)

Vertical (Upper)

CR = 10 (Lower)

5 Points

13 Points

400 500 -

4

CIE 1931

170 200 - cd/m

40

10

30

- - 1.25

- - 1.60

-

- 2 4

- 8 12

0.554 0.584 0.614

0.303 0.333 0.363

0.308 0.338 0.368

0.541 0.571 0.601

0.128 0.158 0.188

0.103 0.133 0.163

0.283 0.313 0.343

0.299 0.329 0.359

45

15

35

6

-

degree

-

8

msec

1, 4,

2

5.

4, 9

1, 3,

4

2, 3,

4

4, 6

4, 7

4, 8

4

NTSC %

B116XW01 V0 Document Version : 0.4

- 45 -

6 of 37

Product Specification

=

Maximum Brightness of thirteen points

Minimum Brightness of thirteen points

Maximum Brightness of five

points

=

Minimum Brightness of five points

Note 1: 5 points position (Ref: Active area)

H /4

AU OPTRONICS CORPORATION

W / 4 W /4 W / 4 W / 4

W

1 2

H

H /4

Note 2: 13 points position (Ref: Active area)

W /4

1 0

H /4

www.jxlcd.com

H /4

H

H /4

1

6

3

4

W

W /4

4 5

W /4

2

7

5

W /4

1 0

3

8

9

H /4

1 0

1 1

1 2

Note 3: The luminance uniformity of 5 or13 points is defined by dividing the maximum luminance values by the minimum test point luminance

δ

W5

1 0

1 3

δ

Note 4: Measurement method

The LCD module should be stabilized at given temperature for 30 minutes to avoid abrupt temperature change

during measuring. In order to stabilize the luminance, the measurement should be executed after lighting

B116XW01 V0 Document Version : 0.4

W13

7 of 37

Product Specification

Field=2

°

Contrast ratio (CR)=

Brightness on the “White” state

Brightness on the “Black” state

AU OPTRONICS CORPORATION

Backlight for 30 minutes in a stable, windless and dark room, and it should be measured in the center of screen.

Photo detector

Note 5： Definition of Average Luminance of White (YL):

Measure the luminance of gray level 63 at 5 points，Y

L (x) is corresponding to the luminance of the point X at Figure in Note (1).

Note 6： Definition of contrast ratio:

Note 7： Definition of Cross Talk (CT)

CT = | YB – YA | / YA × 100 (%)

Where

www.jxlcd.com

Contrast ratio is calculated with the following formula.

= [L (1)+ L (2)+ L (3)+ L (4)+ L (5)] / 5

L

YA = Luminance of measured location without gray level 0 pattern (cd/m2)

YB = Luminance of measured location with gray level 0 pattern (cd/m2)

B116XW01 V0 Document Version : 0.4

8 of 37

Product Specification

Note 8: Definition of response time:

The output signals of BM-7 or equivalent are measured when the input signals are changed from “Black” to

“White” (falling time) and from “White” to “Black” (rising time), respectively. The response time interval between

the 10% and 90% of amplitudes. Refer to figure as below.

AU OPTRONICS CORPORATION

"Black"

100%

S i

90%

g n a l

(

R e

l

a t

i

v

www.jxlcd.com

e

www.jxlcd.com

v a l

u

10%

e )

0%

Tr

Tf

"White""White"

B116XW01 V0 Document Version : 0.4

9 of 37

Product Specification

Note 9. Definition of viewing angle

Viewing angle is the measurement of contrast ratio ≧10, at the screen center, over a 180° horizontal and

180° vertical range (off-normal viewing angles). The 180° viewing angle range is broken down as follows; 90°

(θ) horizontal left and right and 90° (Φ) vertical, high (up) and low (down). The measurement direction is

AU OPTRONICS CORPORATION

typically perpendicular to the display surface with the screen rotated about its center to develop the desired

measurement viewing angle.

www.jxlcd.com

B116XW01 V0 Document Version : 0.4

10 of 37

Product Specification

LLVVDDSS

Source Driver

Balance

3. Functional Block Diagram

The following diagram shows the functional block of the 11.6 inches wide Color TFT/LCD 40 Pin (One CH/connector Module)

C

o n n e

ct

DDCC

o

r

AU OPTRONICS CORPORATION

LVDS

receiver

converter

Panel

Controll

DC/DC

Ga

te Dri ver

IC

TFT-LCD

1366*(3)*768

Pixels

PWM

LLEEDD

www.jxlcd.com

LED_EN:3.3V

www.jxlcd.com

Gamma

Generatio

LED Driver

Boost and

Current

LED light bar

B116XW01 V0 Document Version : 0.4

11 of 37

Product Specification

4. Absolute Maximum Ratings

An absolute maximum rating of the module is as following:

4.1 Absolute Ratings of TFT LCD Module

Item Symbol Min Max Unit Conditions

AU OPTRONICS CORPORATION

Logic/LCD Drive Voltage

Vin -0.3 +4.0 [Volt] Note 1,2

4.2 Absolute Ratings of Environment

Item Symbol Min Max Unit Conditions

Operating Temperature

Operation Humidity HOP 5 95 [%RH] Note 4

Storage Temperature

Storage Humidity HST

Note 1: At Ta (25℃ )

Note 2: Permanent damage to the device may occur if exceed maximum values

Note 3: LED specification refer to section 5.2

Note 4: For quality performance, please refer to AUO IIS (Incoming Inspection Standard).

www.jxlcd.com

TOP 0 +50 [oC] Note 4

TST -20 +60 [oC] Note 4

5 95

Twb=39°C

[%RH]

Note 4

Operating Range

B116XW01 V0 Document Version : 0.4

Storage Range

12 of 37

Product Specification

Voltage

-

90%

10%

5. Electrical characteristics

5.1 TFT LCD Module

5.1.1 Power Specification

Input power specifications are as follows;

The power specification are measured under 25℃ and frame frenquency under 60Hz

AU OPTRONICS CORPORATION

Symble Parameter Min Typ Max Units

VDD Logic/LCD Drive

PDD VDD Power IDD IDD Current

I

Rush

Inrush Current

VDDrp Allowable

3.0 3.3 3.6 [Volt]

- 0.8 [Watt] Note 1/2

- 350

- -

450

2000 [mA]

100 [mV] Logic/LCD Drive Ripple Voltage

Note 1 : Maximum Measurement Condition：Black Pattern

Note 2：Typical Measurement Condition: Mosaic Pattern

Note 3：Measure Condition

+5.0V

www.jxlcd.com

R1 47K

(High to Low) Control Signal

SW1

SW MAG-SPST

1 2

+12.0V

R2

1K

VR1

47K

D6 D5 D2 S D1

G

C3

0.01uF/25V

Q3 AO6402

D2SD1D5

G

D6

Q3

AO6402

F1

[mA]

p-p

Note 1/2

Note 3

C1 1uF/16V

(LCD Module Input)

Note

VCC

C2 1uF/25V

3.3V

0V

0.5ms

Vin rising time

B116XW01 V0 Document Version : 0.4

13 of 37

Product Specification

VSS

5.1.2 Signal Electrical Characteristics

Input signals shall be low or High-impedance state when VDD is off. It is recommended to refer the specifications of THC63LVDF84A (Thine Electronics Inc.) in detail.

Signal electrical characteristics are as follows;

AU OPTRONICS CORPORATION

Parameter

Vth

Vtl

Vcm

Note: LVDS Signal Waveform

V

www.jxlcd.com

t

Differential Input High Threshold (Vcm=+1.2V)

Differential Input Low Threshold (Vcm=+1.2V)

Differential Input

Common Mode Voltage

www.jxlcd.com

Condition Min Max Unit

Vcm

-

-100

1.125

100

-

1.375

[mV]

[V]

B116XW01 V0 Document Version : 0.4

14 of 37

Product Specification

5.2 Backlight Unit

LED Parameter guideline for LED driving selection (Ref. Remark 1)

AU OPTRONICS CORPORATION

Parameter

LED Forward Voltage VF 3.0 3.2 3.4 [Volt]

LED Forward Current IF 20 [mA]

LED Power consumption

LED Life-Time

Output PWM frequency

Duty ratio

Note 1: Calculator value for reference P

Note 2: The LED life-time define as the estimated time to 50% degradation of initial luminous.

www.jxlcd.com

Symbol

P

3.01 3.06

LED

N/A 10,000

F

100 200 20K

PWM

-- 5 -- 100

Min Typ Max

- -

= VF (Normal Distribution) * IF (Normal Distribution) / Efficiency

LED

Units Condition

[Watt]

Hour

Hz

%

(Ta=25℃)

(Ta=25℃) Note 1

(Ta=25℃)

IF=20 mA

Note 2

B116XW01 V0 Document Version: 0.4

15 of 37

Product Specification

6. Signal Characteristic

6.1 Pixel Format Image

Following figure shows the relationship of the input signals and LCD pixel format.

1

AU OPTRONICS CORPORATION

1366

1st Line

768th Line

R G B R G B

www.jxlcd.com

R G B R G B

B116XW01 V0 Document Version: 0.4

16 of 37

Product Specification

Data Clock

6.2 The input data format

Signal Name

R5 R4 R3 R2 R1 R0

Description

Red Data 5 (MSB) Red Data 4 Red Data 3 Red Data 2 Red Data 1 Red Data 0 (LSB)

Red-pixel Data

AU OPTRONICS CORPORATION

Red-pixel Data Each red pixel's brightness data consists of these 6 bits pixel data.

G5 G4 G3 G2 G1 G0

B5 B4 B3 B2 B1 B0

RxCLKIN

DE Display Timing This signal is strobed at the falling edge of

VS Vertical Sync The signal is synchronized to RxCLKIN . HS Horizontal Sync The signal is synchronized to RxCLKIN .

Note: Output signals from any system shall be low or High-impedance state when VDD is off.

Green Data 5 (MSB) Green Data 4 Green Data 3

www.jxlcd.com

Green Data 2

www.jxlcd.com

Green Data 1 Green Data 0 (LSB)

Green-pixel Data Blue Data 5 (MSB) Blue Data 4 Blue Data 3 Blue Data 2 Blue Data 1 Blue Data 0 (LSB)

Blue-pixel Data

Green-pixel Data Each green pixel's brightness data consists of these 6 bits pixel data.

Blue-pixel Data Each blue pixel's brightness data consists of these 6 bits pixel data.

The signal is used to strobe the pixel data and DE signals. All pixel data shall be valid at the falling edge when the DE signal is high.

RxCLKIN. When the signal is high, the pixel data shall be valid to be displayed.

B116XW01 V0 Document Version: 0.4

17 of 37

Product Specification

6.3 Integration Interface and Pin Assignment

LVDS is a differential signal technology for LCD interface and high speed data transfer device.

AU OPTRONICS CORPORATION

PIN# Signal Name

1 NC No Connection (Reserve)

2 AVDD PowerSupply,3.3V(typical)

3 AVDD PowerSupply,3.3V(typical)

4 DVDD DDC 3.3Vpower

5 NC No Connection (Reserve)

6 SCL DDCClock

7 SDA DDCData

8 Rin0- -LVDSdifferential data input(R0-R5,G0)

9 Rin0+ +LVDSdifferential data input(R0-R5,G0)

10 GND Ground

11 Rin1- -LVDSdifferential data input(G1-G5,B0-B1)

12 Rin1+ +LVDSdifferential data input(G1-G5,B0-B1)

13 GND Ground

14 Rin2- -LVDSdifferential data input(B2-B5,HS,VS,DE)

15 Rin2+ +LVDSdifferential data input(B2-B5,HS,VS,DE)

Description

16 GND Ground

17 ClkIN- -LVDSdifferential clock input

18 ClkIN+ +LVDSdifferential clock input

19 GND Ground–Shield

20 NC No Connection (Reserve)

21 NC No Connection (Reserve)

22 GND Ground–Shield

23 NC No Connection (Reserve)

24 NC No Connection (Reserve)

25 GND Ground–Shield

26 NC No Connection (Reserve)

27 NC No Connection (Reserve)

28 GND Ground–Shield

29 NC No Connection (Reserve)

30 NC No Connection (Reserve)

31 VLED_GND LED Ground

www.jxlcd.com

32 VLED_GND LED Ground

33 VLED_GND LED Ground

34 NC No Connection (Reserve)

B116XW01 V0 Document Version: 0.4

18 of 37

Product Specification

35 PWM System PWM Signal Input

AU OPTRONICS CORPORATION

36 LED_EN

37 NC No Connection (Reserve)

38 VLED LED Power Supply 6V-21V

39 VLED LED Power Supply 6V-21V

40 VLED LED Power Supply 6V-21V

LED enable pin(+

3.3±0.3

V Input)

www.jxlcd.com

B116XW01 V0 Document Version: 0.4

19 of 37

1

NC

Connector

Note1: Start from right side

Product Specification

AU OPTRONICS CORPORATION

www.jxlcd.com

40

Note2: Input signals shall be low or High-impedance state when VDD is off.

B116XW01 V0 Document Version: 0.4

20 of 37

Product Specification

12

internal circuit of LVDS inputs are as following. The module uses a 100ohm resistor between positive and negative data lines of each receiver input

Signal Input

Pin No .

8

RxIN0-

9

RxIN0+

11

RxIN1-

RxIN1+

14

RxIN2-

15

RxIN2+

AU OPTRONICS CORPORATION

LVDS Receiver

R

17

18

RxCLK IN-

RxCLKIN+

R

www.jxlcd.com

B116XW01 V0 Document Version: 0.4

21 of 37

Product Specification

6.4 Interface Timing

6.4.1 Timing Characteristics

Basically, interface timings should match the 1366x768 /60Hz manufacturing guide line timing.

Parameter Symbol Min. Typ. Max. Unit

Frame Rate - 50 60 - Hz

AU OPTRONICS CORPORATION

Clock frequency 1/ T

Vertical

Section

Horizontal

Section

Note : DE mode only

6.4.2 Timing diagram

T

CLOCK

DOTCLK

www.jxlcd.com

Input

Data

DE

- 72 - MHz

Clock

Period 780 803 - 1023

Active 768 - 768

Blanking 12 35 - 255

Period 1426 1494 - 2047

Active - 1366 - 1366

Blanking 60 128 - 681

Input Timing Definition ( DE Mode)

Invaild

Data

T

HB

Pixel

1

T

VB

Pixel

2

T

Pixel

3

T

HD

H

T

V

Pixel

N-1

T

VD

Pixel

T

Line

T

Clock

Invaild

N

Data

Pixel

1

B116XW01 V0 Document Version: 0.4

22 of 37

Product Specification

6.5 Power ON/OFF Sequence

VDD power on/off sequence is as follows. Interface signals are also shown in the chart. Signals from any system shall be Hi-Z state or low level when VDD is off

AU OPTRONICS CORPORATION

Power Sequence Timing

www.jxlcd.com

Parameter

T1 0.5 - 10

T2 0 - 50

T3 0 - 50

T4 400 - -

T5 200 - -

T6 200 - -

T7 0 - 10

Min. Typ. Max.

Value

Units

ms

B116XW01 V0 Document Version: 0.4

23 of 37

Product Specification

LED on/off sequence is as follows. Interface signals are also shown in the chart.

AU OPTRONICS CORPORATION

Values

Symbol

T1

www.jxlcd.com

Note: The duty of LED dimming signal should be more than 5% in T2 and T3.

T2

T3

T4

T5

Min Typ Max

10 --- ---

50 --- ---

0 --- ---

10 --- ---

Unit

ms

B116XW01 V0 Document Version: 0.4

24 of 37

Product Specification

7. Connector Description

Physical interface is described as for the connector on module.

These connectors are capable of accommodating the following signals and will be following components.

7.1 TFT LCD Module

Connector Name / Designation For Signal Connector

Manufacturer IPEX or compatible

AU OPTRONICS CORPORATION

Type / Part Number

Mating Housing/Part Number

www.jxlcd.com

IPEX 20455-040E-12A

IPEX 20453-040E-01

or compatible

B116XW01 V0 Document Version: 0.4

25 of 37

Product Specification

8. LED Driving Specification

8.1 Connector Description

It is a intergrative interface and comibe into LVDS connector. The type and mating refer to section 7.

8.2 Pin Assignment

Ref. to 6.3

AU OPTRONICS CORPORATION

www.jxlcd.com

B116XW01 V0 Document Version: 0.4

26 of 37

Product Specification

9. Vibration and Shock Test

9.1 Vibration Test

Test Spec:

Test method: Non-Operation



Acceleration: 1.5 G



Frequency: 10 - 500Hz Random



Sweep: 30 Minutes each Axis (X, Y, Z)



9.2 Shock Test Spec:

Test Spec:

Test method: Non-Operation



AU OPTRONICS CORPORATION

Acceleration: 220 G , Half sine wave



Active time: 2 ms



Pulse: X,Y,Z .one time for each side



www.jxlcd.com

B116XW01 V0 Document Version: 0.4

27 of 37

10. Reliability

Items

Temperature

Humidity Bias

High Temperature

Operation

Low Temperature

Operation

High Temperature

Storage

Low Temperature

Storage

Thermal Shock

Test

Product Specification

AU OPTRONICS CORPORATION

Required Condition Note

Ta= 40℃℃℃℃, 90%RH, 300h

Ta= 50℃℃℃℃, Dry, 300h

Ta= 0℃℃℃℃, 300h

Ta= 60℃℃℃℃, 35%RH, 300h

Ta= -20℃℃℃℃, 50%RH, 250h

Ta=-20℃℃℃℃to 60℃℃℃℃, Duration at 30 min, 100 cycles

ESD

Note1: According to EN 61000-4-2 , ESD class B: Some performance degradation allowed. No data lost

. Self-recoverable. No hardware failures.

Remark: MTBF (Excluding the LED): 30,000 hours with a confidence level 90%

www.jxlcd.com

Contact : ±8 KV

Air : ±15 KV

Note 1

B116XW01 V0 Document Version: 0.4

28 of 37

Product Specification

11. Mechanical Characteristics

11.1 LCM Outline Dimension

AU OPTRONICS CORPORATION

www.jxlcd.com

B116XW01 V0 Document Version: 0.4

29 of 37

Product Specification

AU OPTRONICS CORPORATION

www.jxlcd.com

Note: Prevention IC damage, IC positions not allowed any overlap over these areas.

B116XW01 V0 Document Version: 0.4

30 of 37

Product Specification

AU OPTRONICS CORPORATION

12. Shipping and Package

12.1 Shipping Label Format

Size :90 mm(length) ×35mm(width)

www.jxlcd.com

B116XW01 V0 Document Version: 0.4

31 of 37

12.2 Carton package

Carton Label: 80mm * 40mm

Product Specification

AU OPTRONICS CORPORATION

35

B116XW01

97.11B01.XXX

The outside dimension of carton is 469(L)mm* 378(W)mm* 266(H)mm, carton and cushion weight are 2590g

www.jxlcd.com

B116XW01 V0 Document Version: 0.4

32 of 37

Product Specification

12.3 Shipping package of palletizing sequence

The outside dimension of Pallet is 114(L)mm* 98(W)mm* 13.8(H)mm

By air : 6 *5 layers, one pallet put 30 boxes, total 1050 pcs module. By sea : 6 *7 layers, one pallet put 42 boxes, total 1470 pcs module.

Stretch film

AU OPTRONICS CORPORATION

Top cardboard

Label

Bottom cardboard

PET band

Corner angle

Wooden pallet

www.jxlcd.com

B116XW01 V0 Document Version: 0.4

33 of 37

Product Specification

13. Appendix: EDID description

AU OPTRONICS CORPORATION

Address

HEX

00

01

02

03

04

05

06

07

08

09

0A

0B

0C

0D

0E

0F

10

11

12

13

14

15

16

17

18

19

1A

1B

1C

1D

1E

1F

20

21

22

23

24

25

26

FUNCTION Value Value Value Note

HEX BIN DEC

Header 00 00000000 0

FF 11111111 255

00 00000000 0

EISA Manuf. Code LSB 06 00000110 6

Compressed ASCII AF 10101111 175

Product Code

hex, LSB first

32-bit ser # 00 00000000 0

00 00000000 0

Week of manufacture 01 00000001 1

Year of manufacture 12 00010010 18

www.jxlcd.com

Video input def.

Max H image size

Max V image size

Display Gamma

Feature support

EDID Structure Ver. 01 00000001 1

EDID revision # 03 00000011 3

(digital I/P, non-TMDS,

CRGB)

(rounded to cm)

(=(gamma*100)-100)

(no DPMS, Active OFF,

RGB, tmg Blk#1)

Red/green low bits (Lower 2:2:2:2 bits)

Blue/white low bits (Lower 2:2:2:2 bits)

Red x (Upper 8 bits)

Red y/ highER 8 bits 55 01010101 85

Green x 56 01010110 86

Green y 92 10010010 146

Blue x 28 00101000 40

Blue y 22 00100010 34

White x 50 01010000 80

White y 54 01010100 84

Established timing 1 00 00000000 0

Established timing 2 00 00000000 0

Established timing 3 00 00000000 0

Standard timing #1 01 00000001 1

5C 01011100 92

10 00010000 16

80 10000000 128

1A 00011010 26

0E 00001110 14

78 01111000 120

0A 00001010 10

99 10011001 153

85 10000101 133

95 10010101 149

B116XW01 V0 Document Version: 0.4

34 of 37

Product Specification

27

28

29

2A

2B

2C

2D

2E

2F

30

31

32

33

34

35

36

37

38

39

3A

3B

3C

3D

3E

3F

40

41

42

43

44

45

46

47

48

49

4A

4B

4C

4D

4E

4F

50

B116XW01 V0 Document Version: 0.4

Pixel Clock/10000 LSB

Pixel Clock/10000 USB

Horz active Lower 8bits

Horz blanking Lower 8bits

HorzAct:HorzBlnk Upper 4:4 bits

Vertical Active Lower 8bits

Vertical Blanking Lower 8bits

www.jxlcd.com

Vert Act : Vertical Blanking (upper

4:4 bit)

HorzSync. Offset

HorzSync.Width

VertSync.Offset : VertSync.Width

Horz&Vert Sync Offset/Width Upper 2bits

Horizontal Image Size Lower 8bits

Vertical Image Size Lower 8bits

Horizontal & Vertical Image Size (upper

4:4 bits)

Horizontal Border

Vertical Border Signal

pol)

(non-intr, norm, no stero, sep sync, neg

Standard timing #2 01 00000001 1

Standard timing #3 01 00000001 1

Standard timing #4 01 00000001 1

Standard timing #5 01 00000001 1

Standard timing #6 01 00000001 1

Standard timing #7 01 00000001 1

Standard timing #8 01 00000001 1

Detailed timing/monitor 00 00000000 0

descriptor #2 00 00000000 0

AU OPTRONICS CORPORATION

01 00000001 1

20 00100000 32

1C 00011100 28

56 01010110 86

80 10000000 128

50 01010000 80

00 00000000 0

23 00100011 35

30 00110000 48

20 00100000 32

36 00110110 54

00 00000000 0

90 10010000 144

10 00010000 16

(zero for internal LCD)

00 00000000 0

0F 00001111 15

00 00000000 0

18 00011000 24

35 of 37

Product Specification

51

52

53

54

55

56

57

58

59

5A

5B

5C

5D

5E

5F

60

61

62

63

64

65

66

67

68

69

6A

6B

6C

6D

6E

6F

70

71

72

73

74

75

76

77

78

79

7A

7B

B116XW01 V0 Document Version: 0.4

www.jxlcd.com

Detailed timing/monitor 00 00000000 0

descriptor #3 00 00000000 0

Manufacture 41 01000001 65 A

Manufacture 55 01010101 85 U

Manufacture 4F 01001111 79 O

Detailed timing/monitor 00 00000000 0

descriptor #4 00 00000000 0

Manufacture P/N 42 01000010 66 B

Manufacture P/N 31 00110001 49 1

Manufacture P/N 36 00110110 54 6

Manufacture P/N 58 01011000 88 X

Manufacture P/N 57 01010111 87 W

Manufacture P/N 30 00110000 48 0

Manufacture P/N 31 00110001 49 1

Manufacture P/N 20 00100000 32

Manufacture P/N 56 01010110 86 V

Manufacture P/N 30 00110000 48 0

AU OPTRONICS CORPORATION

00 00000000 0

20 00100000 32

00 00000000 0

FE 11111110 254

00 00000000 0

0A 00001010 10

20 00100000 32

00 00000000 0

FE 11111110 254

00 00000000 0

36 of 37

Product Specification

7C

7D

7E

7F

SUM

SUM to HEX

Extension Flag 00 00000000 0

Checksum CF 11001111 207

AU OPTRONICS CORPORATION

20 00100000 32

0A 00001010 10

5888 1700

www.jxlcd.com

B116XW01 V0 Document Version: 0.4

37 of 37

AU Optronics B116XW01-V0 Product Specification

Specifications and Main Features

Frequently Asked Questions

User Manual