Product Specification
) Preliminary Specifications
( V
( ) Final Specifications
Module 10.1” WSVGA Color TFT-LCD with LED Backlight design
AU OPTRONICS CORPORATION
Model Name
Note ( )
Customer Date
www.jxlcd.com
www.jxlcd.com
Checked &
Approved by
B101AW03 V0 HW: 1A
LED Backlight with driving circuit design
Date
Approved by Date
Howard Lee
Prepared by
09/30/2008
Note: This Specification is subject to change
without notice.
B101AW03 V0 (Document Version : 0.1)
Winston Lin
NBBU Marketing Division /
AU Optronics corporation
09/30/2008
1 of 35
Product Specification
AU OPTRONICS CORPORATION
Contents
1. Handling Precautions ..........................................................................................4
2. General Description.............................................................................................5
2.1 General Specification.........................................................................................................5
2.2 Optical Characteristics.......................................................................................................6
3. Functional Block Diagram.................................................................................11
4. Absolute Maximum Ratings..............................................................................12
4.1 Absolute Ratings of TFT LCD Module..............................................................................12
4.2 Absolute Ratings of Environment.....................................................................................12
5. Electrical characteristics...................................................................................13
5.1 TFT LCD Module..............................................................................................................13
5.2 Backlight Unit...................................................................................................................15
6. Signal Characteristic..........................................................................................16
6.1 Pixel Format Image..........................................................................................................16
6.2 The input data format.......................................................................................................16
6.3 Integration Interface and Pin Assignment........................................................................18
6.4 Interface Timing ...............................................................................................................19
7. Connector Description.......................................................................................22
7.1 TFT LCD Module..............................................................................................................22
www.jxlcd.com
www.jxlcd.com
8. LED Driving Specification .................................................................................23
8.1 Connector Description .....................................................................................................23
8.2 Pin Assignment................................................................................................................23
9. Vibration and Shock Test..................................................................................24
9.1 Vibration Test...................................................................................................................24
9.2 Shock Test Spec:..............................................................................................................24
10. Reliability...........................................................................................................25
11. Mechanical Characteristics.............................................................................26
11.1 LCM Outline Dimension .................................................................................................26
11.2 Screw Hole Depth and Center Position..........................................................................28
12. Shipping and Package.....................................................................................29
12.1 Shipping Label Format...................................................................................................29
12.2 Carton package..............................................................................................................30
12.3 Shipping package of palletizing sequence.....................................................................31
13. Appendix: EDID description............................................................................32
B101AW03 V0 (Document Version : 0.1)
2 of 35
Product Specification
AU OPTRONICS CORPORATION
Record of Revision
Version and Date Page
0.1 2008/09/30 All First Edition for Customer
0.2 2008/12/03 21 Panel (LED) LED power
sequence
0.2 2008/12/03 29 Shipping label format Shipping label format
0.2 2008/12/03 32- EDID description EDID description
0.3 2008/12/26 27 2D drawing (back) 2D drawing (back)
0.3 2008/12/26 32- EDID description EDID description
0.4 2008/01/15 6 RGB color spec RGB color spe
0.4 2008/01/15 32- EDID description EDID description
www.jxlcd.com
www.jxlcd.com
Old description New Description Remark
Panel (LED) LED power sequence
waveform & parameter updated
information updated
addition
updated with rotation
update for CLK spec modify
from TBD to value definition
update for CLK spec modify
B101AW03 V0 (Document Version : 0.1)
3 of 35
Product Specification
1. Handling Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or
spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard
surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure
human earth when handling.
7) Do not open nor modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor
AU OPTRONICS CORPORATION
tilt the Interface Connector of the TFT Module.
10) After installation of the TFT Module into an enclosure (Notebook PC Bezel, for
example), do not twist nor bend the TFT Module even momentary. At designing the
enclosure, it should be taken into consideration that no bending/twisting forces are
applied to the TFT Module from outside. Otherwise the TFT Module may be
damaged.
www.jxlcd.com
11) Small amount of materials having no flammability grade is used in the LCD module.
The LCD module should be supplied by power complied with requirements of Limited
Power Source (IEC60950 or UL1950), or be applied exemption.
12) Disconnecting power supply before handling LCD modules, it can prevent electric
shock, DO NOT TOUCH the electrode parts, cables, connectors and LED circuit part
of TFT module that a LED light bar build in as a light source of back light unit. It can
prevent electrostic breakdown.
www.jxlcd.com
B101AW03 V0 (Document Version : 0.1)
4 of 35
Product Specification
Length
234.5
235.0
235.5
Width
142.5
143.0
143.5
Thickness
- -
5.2
2. General Description
B101AW03 V0 is a Color Active Matrix Liquid Crystal Display composed of a TFT LCD panel, a
driver circuit, and LED backlight system. The screen format is intended to support the WSVGA
(1024(H) x 600(V)) screen and 262k colors (RGB 6-bits data driver) with LED backlight driving
circuit. All input signals are LVDS interface compatible.
B101AW03 V0 is designed for a display unit of notebook style personal computer and industrial
machine.
AU OPTRONICS CORPORATION
2.1 General Specification
The following items are characteristics summary on the table at 25 ℃ condition:
Items Unit Specifications
Screen Diagonal [mm] 255.54 (10.1 W”)
Active Area [mm] 222.72 x 125.28
Pixels H x V 1024 x 3(RGB) x 600
Pixel Pitch [mm] 0.2175 (H) X 0.2088 (V)
Pixel Format R.G.B. Vertical Stripe
Display Mode Normally White
www.jxlcd.com
White Luminance (I
(Note: ILED is LED current)
Luminance Uniformity 1.25 max. (5 points); 1.6 max (13 points)
Contrast Ratio 400:1 typ; 300:1 min
Response Time [ms] 16 typ / 25 Max
www.jxlcd.com
LED
=20mA)
[cd/m2] 200 typ. (5 points average)
170 min. (5 points average)
Nominal Input Voltage VDD [Volt] +3.3 typ.
Power Consumption [Watt] 2.8 max.
Weight [Grams] 190 max.
Physical Size without inverter,
bracket.
Electrical Interface 1 channel LVDS
Glass thickness mm 0.5mm
Surface Treatment Glare, Hardness 3H
Support Color 262K colors ( RGB 6-bit )
B101AW03 V0 (Document Version : 0.1)
[mm]
Min. Typ. Max.
5 of 35
Product Specification
Storage (Non
-
Operating)
[oC]
-
20 to +60
oHS Compliance
Temperature Range
Operating
RoHS Compliance R
2.2 Optical Characteristics
The optical characteristics are measured under stable conditions at 25℃ (Room Temperature) :
AU OPTRONICS CORPORATION
[oC]
0 to +50
Item Symbol
White Luminance
I
LED
=20mA
Viewing Angle
Luminance Uniformity
Luminance Uniformity
Contrast Ratio CR
Cross talk %
Response Time
Color /
Chromaticity
Coordinates
www.jxlcd.com
www.jxlcd.com
Red
Green
Blue
White
Conditions Min. Typ. Max. Unit Note
θ
R
θ
L
ψ
H
ψ
L
δ
5P
δ
13P
Tr Rising
Tf Falling
TRT Rising + Falling
Rx
Ry
Gx
Gy
Bx
By
Wx
Wy
5 points average
Horizontal (Right)
CR = 10 (Left)
Vertical (Upper)
CR = 10 (Lower)
5 Points
13 Points
300 400 -
4
CIE 1931
170 200 - cd/m
40
40
10
30
- - 1.25
- - 1.60
-
- - -
- 16 25
0.558 0.588 0.618
0.321 0.351 0.381
0.312 0.342 0.372
0.537 0.567 0.597
0.128 0.158 0.188
0.093 0.123 0.153
0.283 0.313 0.343
0.299 0.329 0.359
45
45
15
35
-
-
degree
-
-
-
msec
2
1, 4, 5.
4, 9
1, 3, 4
2, 3, 4
4, 6
4, 7
4, 8
4
NTSC %
B101AW03 V0 (Document Version : 0.1)
- 45 -
6 of 35
Product Specification
=
Maximum Brightness of thirteen points
Minimum Brightness of thirteen points
Maximum Brightness of five
points
=
Minimum Brightness of five points
Note 1: 5 points position (Ref: Active area)
H /4
H /4
AU OPTRONICS CORPORATION
W /4 W /4 W /4 W /4
W
1 2
H
H /4
H /4
Note 2: 13 points position (Ref: Active area)
W /4
10
10
H/4
www.jxlcd.com
www.jxlcd.com
H/4
H
H/4
1
6
3
4 5
W
W /4
4
W /4
2
7
W /4
10
3
5
8
9
H/4
10
11
Note 3: The luminance uniformity of 5 or13 points is defined by dividing the maximum luminance values by the
minimum test point luminance
δ
W5
10
1312
δ
Note 4: Measurement method
The LCD module should be stabilized at given temperature for 30 minutes to avoid abrupt temperature change
during measuring. In order to stabilize the luminance, the measurement should be executed after lighting Backlight
B101AW03 V0 (Document Version : 0.1)
W13
7 of 35
Product Specification
Field=2
°
Contrast ratio (CR)=
Brightness on the “White” state
Brightness on the “Black” state
for 30 minutes in a stable, windless and dark room, and it should be measured in the center of screen.
AU OPTRONICS CORPORATION
Note 5： Definition of Average Luminance of White (YL):
Photo detector
Measure the luminance of gray level 63 at 5 points，Y
L (x) is corresponding to the luminance of the point X at Figure in Note (1).
Note 6： Definition of contrast ratio:
Note 7： Definition of Cross Talk (CT)
CT = | YB – YA | / YA × 100 (%)
Where
YA = Luminance of measured location without gray level 0 pattern (cd/m2)
www.jxlcd.com
www.jxlcd.com
Contrast ratio is calculated with the following formula.
= [L (1)+ L (2)+ L (3)+ L (4)+ L (5)] / 5
L
YB = Luminance of measured location with gray level 0 pattern (cd/m2)
B101AW03 V0 (Document Version : 0.1)
8 of 35
Product Specification
Note 8: Definition of response time:
The output signals of BM-7 or equivalent are measured when the input signals are changed from “Black” to
“White” (falling time) and from “White” to “Black” (rising time), respectively. The response time interval between
the 10% and 90% of amplitudes. Refer to figure as below.
AU OPTRONICS CORPORATION
"Black"
100%
S
i
90%
g
n
a
l
(
R
e
l
a
t
i
v
e
v
a
l
u
e
)
www.jxlcd.com
www.jxlcd.com
10%
0%
Tr
Tf
"White""White"
B101AW03 V0 (Document Version : 0.1)
9 of 35
Product Specification
Note 9. Definition of viewing angle
Viewing angle is the measurement of contrast ratio ≧10, at the screen center, over a 180° horizontal an d 180°
vertical range (off-normal viewing angles). The 180° viewing angle range is broken down as follows; 90° ( θ)
horizontal left and right and 90° ( Φ) vertical, high (up) and low (down). The measurement direction is typically
perpendicular to the display surface with the screen rotated about its center to develop the desired measurement
viewing angle.
AU OPTRONICS CORPORATION
www.jxlcd.com
www.jxlcd.com
B101AW03 V0 (Document Version : 0.1)
10 of 35
Product Specification
3. Functional Block Diagram
The following diagram shows the functional block of the 10.1 inches wide Color TFT/LCD 40 Pin (One
CH/connector Module)
AU OPTRONICS CORPORATION
www.jxlcd.com
www.jxlcd.com
B101AW03 V0 (Document Version : 0.1)
11 of 35
Product Specification
4. Absolute Maximum Ratings
An absolute maximum rating of the module is as following:
4.1 Absolute Ratings of TFT LCD Module
Item Symbol Min Max Unit Conditions
Logic/LCD Drive
4.2 Absolute Ratings of Environment
Item Symbol Min Max Unit Conditions
AU OPTRONICS CORPORATION
Vin -0.3 +4.0 [Volt] Note 1,2
Operating Temperature
Operation Humidity HOP 10 90 [%RH] Note 4
Storage Temperature
Storage Humidity HST
Note 1: At Ta (25℃ )
Note 2: Permanent damage to the device may occur if exceed maximum values
Note 3: LED specification refer to section 5.2
Note 4: For quality performance, please refer to AUO IIS (Incoming Inspection Standard).
www.jxlcd.com
www.jxlcd.com
TOP 0 +50 [oC] Note 4
TST -20 +60 [oC] Note 4
10 90
Twb=39°C
[%RH]
Note 4
Operating Range
B101AW03 V0 (Document Version : 0.1)
Storage Range
12 of 35
Product Specification
Voltage
90%
10%
5. Electrical characteristics
5.1 TFT LCD Module
5.1.1 Power Specification
Input power specifications are as follows;
The power specification are measured under 25 and frame frenquency under 60Hz℃
AU OPTRONICS CORPORATION
Symble Parameter Min Typ Max Units
VDD Logic/LCD Drive
PDD VDD Power
IDD IDD Current
I
Rush
Inrush Current
VDDrp Allowable
3.0 3.3 3.6 [Volt]
0.50
- 150
-
-
-
-
- [Watt] Note 1/2
-
1500 [mA]
100 [mV]
Logic/LCD Drive
Ripple Voltage
Note 1 : Maximum Measurement Condition：Black Pattern
Note 2：Typical Measurement Condition: Mosaic Pattern
Note 3：Measure Condition
+5.0V
www.jxlcd.com
www.jxlcd.com
R1
47K
(High to Low)
Control
Signal
SW1
SW MAG-SPST
1 2
+12.0V
R2
1K
VR1
47K
D6
D5
D2 S
D1
G
C3
0.01uF/25V
Q3
AO6402
D2SD1D5
G
D6
Q3
AO6402
F1
[mA]
p-p
Note 1/2
Note 3
(LCD Module Input)
C1
1uF/16V
Note
VCC
C2
1uF/25V
0V
B101AW03 V0 (Document Version : 0.1)
3.3V
0.5ms
Vin rising time
13 of 35
Product Specification
VSS
5.1.2 Signal Electrical Characteristics:
Input signals shall be low or High-impedance state when VDD is off.
It is recommended to refer the specifications of SN75LVDS82DGG (Texas Instruments) in
detail.
Signal electrical characteristics are as follows;
AU OPTRONICS CORPORATION
Parameter
Vth
Vtl
Vcm
Note: LVDS Signal Waveform
V
t
Differential Input High
Threshold (Vcm=+1.2V)
Differential Input Low
Threshold (Vcm=+1.2V)
Differential Input
Common Mode Voltage
www.jxlcd.com
www.jxlcd.com
Condition Min Max Unit
Vcm
-
-100
1.125
100
-
1.375
[mV]
[mV]
[V]
B101AW03 V0 (Document Version : 0.1)
14 of 35
Product Specification
5.2 Backlight Unit
LED Parameter guideline for LED driving selection (Ref. Remark 1)
AU OPTRONICS CORPORATION
Parameter
LED Forward Voltage VF 4 [Volt]
LED Forward Current IF 20 30 [mA]
LED Power
consumption
LED Life-Time
Output PWM frequency
Duty ratio
Note 1: Calculator value for reference IF×VF =P
Note 2: The LED life-time define as the estimated time to 50% degradation of initial luminous.
www.jxlcd.com
www.jxlcd.com
Symbol
P
2.16
LED
N/A 10,000
F
PWM
-- 5 -- 100
Min Typ Max
- -
100 200 20K
Units Condition
[Watt]
Hour
Hz
%
(Ta=25 )℃
(Ta=25 )℃
(Ta=25 )℃
Note 1
(Ta=25 )℃
IF=20 mA
Note 2
Note 3: This panel will support lower duty ration at PWM conditional frequency. The PWM frequency constrain
between 100Hz to 300Hz and a same typical 200Hz. The duty ration will support from 5% to 100%
B101AW01 V0 (Document Version: 0.4)
15 of 35
Product Specification
6. Signal Characteristic
6.1 Pixel Format Image
Following figure shows the relationship of the input signals and LCD pixel format.
AU OPTRONICS CORPORATION
www.jxlcd.com
www.jxlcd.com
6.2 The input data format: TBD
Note: Output signals from any system shall be low or High-impedance state when VDD is off.
B101AW01 V0 (Document Version: 0.4)
16 of 35
Data Clock
Signal Name
R5
R4
R3
R2
R1
R0
Product Specification
Description
Red Data 5 (MSB)
Red Data 4
Red Data 3
Red Data 2
Red Data 1
Red Data 0 (LSB)
Red-pixel Data
AU OPTRONICS CORPORATION
Red-pixel Data
Each red pixel's brightness data consists of
these 6 bits pixel data.
G5
G4
G3
G2
G1
G0
B5
B4
B3
B2
B1
B0
RxCLKIN
DE Display Timing This signal is strobed at the falling edge of
VS Vertical Sync The signal is synchronized to RxCLKIN .
HS Horizontal Sync The signal is synchronized to RxCLKIN .
Note: Output signals from any system shall be low or High-impedance state when VDD is off.
Green Data 5 (MSB)
Green Data 4
Green Data 3
Green Data 2
Green Data 1
Green Data 0 (LSB)
Green-pixel Data
Blue Data 5 (MSB)
Blue Data 4
Blue Data 3
Blue Data 2
Blue Data 1
Blue Data 0 (LSB)
Blue-pixel Data
www.jxlcd.com
www.jxlcd.com
Green-pixel Data
Each green pixel's brightness data consists of
these 6 bits pixel data.
Blue-pixel Data
Each blue pixel's brightness data consists of
these 6 bits pixel data.
The typical frequency is 54.2MHZ.The signal is
used to strobe the pixel data and DE signals. All
pixel data shall be valid at the falling edge when
the DE signal is high.
RxCLKIN. When the signal is high, the pixel
data shall be valid to be displayed.
B101AW01 V0 (Document Version: 0.4)
17 of 35
Product Specification
6.3 Integration Interface and Pin Assignment: TBD
Pin Signal Description Pin Signal Description
1 NC No Connection 21 NC No Connection (Reserve)
2 AVDD PowerSupply,3.3V(typical) 22 GND Ground
3 AVDD PowerSupply,3.3V(typical) 23 NC No Connection (Reserve)
4 DVDD DDC 3.3Vpower 24 NC No Connection (Reserve)
AU OPTRONICS CORPORATION
5 NC No Connection (Reserve) 25 GND
6 SCL DDCClock 26 NC No Connection (Reserve)
7 SDA DDCData 27 NC No Connection (Reserve)
8 Rin0-
9 Rin0+
10 GND Ground 30 NC No Connection (Reserve)
11 Rin1-
12 Rin1+
13 GND Ground 33 VLED_GND LED Ground
14 Rin2-
15 Rin2+
-LVDS differential data
input(R0-R5,G0)
+LVDS differential data
input(R0-R5,G0)
-LVDS differential data
input(G1-G5,B0-B1)
+LVDS differential data
www.jxlcd.com
www.jxlcd.com
input(G1-G5,B0-B1)
-LVDS differential data
input(B2-B5,HS,VS,DE)
+LVDS differential data
input(B2-B5,HS,VS,DE)
28 GND
29 NC No Connection (Reserve)
31 VLED_GND LED Ground
32 VLED_GND LED Ground
34 NC No Connection (Reserve)
35 PWM System PWM Signal Input
Ground–Shield
Ground–Shield
16 GND Ground 36 LED_EN LED enable pin(+3V Input)
17 ClkIN-
18 ClkIN+
19 GND Ground 39 VLED LED Power Supply 5V~21V
20 NC NC 40 VLED LED Power Supply 5V~21V
B101AW01 V0 (Document Version: 0.4)
-LVDS differential clock
37 NC No Connection (Reserve)
input
+LVDS differential clock
38 VLED LED Power Supply 5V~21V
input
18 of 35
Product Specification
6.4 Interface Timing
6.4.1 Timing Characteristics
Basically, interface timings should match the 1024 x 600 /60Hz manufacturing guide line
timing.
Parameter Symbol Min. Typ. Max. Unit
Frame Rate - 60 Hz
AU OPTRONICS CORPORATION
Clock frequency 1/ T
Period TV 650
Vertical
Active TVD 600
Section
Blanking TVB 50
Period TH 1405
Horizontal
Active THD 1024
Section
Blanking THB 381
Note : DE mode only
54.8 MHz
Clock
www.jxlcd.com
www.jxlcd.com
T
T
Line
Clock
B101AW01 V0 (Document Version: 0.4)
19 of 35
6.4.2 Timing diagram
T
CLOCK
DOTCLK
Input
Data
DE
DE
www.jxlcd.com
www.jxlcd.com
Invaild
Data
T
Product Specification
AU OPTRONICS CORPORATION
Input Timing Definition ( DE Mode)
HB
Pixel
1
T
VB
Pixel
2
T
Pixel
3
T
HD
H
T
V
Pixel
N-1
T
VD
Pixel
N
Invaild
Data
Pixel
1
B101AW01 V0 (Document Version: 0.4)
20 of 35
Product Specification
6.5 Power ON/OFF Sequence:
6.5.1 Panel Power Sequence
VDD power and LED on/off sequence is as follows. Interface signals are also shown in the
chart. Signals from any system shall be Hi-Z state or low level when VDD is off.
AU OPTRONICS CORPORATION
www.jxlcd.com
www.jxlcd.com
.
Parameter
T1 0.5 - 10 [ms]
T2 30 40 50 [ms]
T3 200 - - [ms]
T4 10 - - [ms]
T5 10 - - [ms]
T6 0 - - [ms]
T7 10 - - [ms]
T8 100 - - [ms]
T9 0 16 50 [ms]
T10 - - 10 [ms]
T11 1000 - - [ms]
Min. Typ. Max.
Value
Unit
B101AW01 V0 (Document Version: 0.4)
21 of 35
Product Specification
7. Connector Description
Physical interface is described as for the connector on module.
These connectors are capable of accommodating the following signals and will be following
components.
7.1 TFT LCD Module
Connector Name / Designation For Signal Connector
Manufacturer IPEX / IPEX compatible
AU OPTRONICS CORPORATION
Type / Part Number
Mating Housing/Part Number
www.jxlcd.com
www.jxlcd.com
IPEX 20455-040E-12
IPEX 20453-040T-11
B101AW01 V0 (Document Version: 0.4)
22 of 35
Product Specification
8. LED Driving Specification
8.1 Connector Description
It is a intergrative interface and comibe into LVDS connector. The type and mating refer to
section 7.
8.2 Pin Assignment
Ref. to 6.3
AU OPTRONICS CORPORATION
www.jxlcd.com
www.jxlcd.com
B101AW01 V0 (Document Version: 0.4)
23 of 35
Product Specification
9. Vibration and Shock Test
9.1 Vibration Test
Test Spec:
Test method: Non-Operation
Acceleration: 1.5 G
Frequency: 10 - 500Hz Random
Sweep: 30 Minutes each Axis (X, Y, Z)
9.2 Shock Test Spec:
Test Spec:
Test method: Non-Operation
AU OPTRONICS CORPORATION
Acceleration: 220 G , Half sine wave
Active time: 2 ms
Pulse: X,Y,Z .one time for each side
www.jxlcd.com
www.jxlcd.com
B101AW01 V0 (Document Version: 0.4)
24 of 35
10. Reliability
Temperature
Humidity Bias
Items
Product Specification
AU OPTRONICS CORPORATION
Required Condition Note
Ta= 40℃, 90%RH, 300h
High Temperature Operation
Low Temperature Operation
High Temperature Storage
Low Temperature Storage
Thermal Shock
Test
ESD
Note1:
Remark:
According to EN 61000-4-2 , ESD class B: Some performance degradation allowed. No data lost
. Self-recoverable. No hardware failures.
MTBF (Excluding the LED): 30,000 hours with a confidence level 90%
www.jxlcd.com
www.jxlcd.com
Ta= 50℃, Dry, 300h
Ta= 0℃, 300h
Ta= 60℃, 35%RH, 300h
Ta= -20℃, 50%RH, 250h
Ta=-20℃to 60℃, Duration at 30 min, 100 cycles
Contact : ±8 KV
Air : ±15 KV
Note 1
B101AW01 V0 (Document Version: 0.4)
25 of 35
Product Specification
11. Mechanical Characteristics
11.1 LCM Outline Dimension:
AU OPTRONICS CORPORATION
www.jxlcd.com
www.jxlcd.com
B101AW01 V0 (Document Version: 0.4)
26 of 35
Product Specification
AU OPTRONICS CORPORATION
www.jxlcd.com
www.jxlcd.com
B101AW01 V0 (Document Version: 0.4)
27 of 35
Product Specification
11.2 Screw Hole Depth and Center Position:
Screw hole maximum depth, from side surface = 2.0 mm (See drawing)
Screw hole center location, from front surface = 2.8 ± 0.3mm (See drawing)
AU OPTRONICS CORPORATION
Screw Torque: Maximum 2.5 kgf-cm
www.jxlcd.com
www.jxlcd.com
B101AW01 V0 (Document Version: 0.4)
28 of 35
Product Specification
H/W: 1A F/W:1
12. Shipping and Package
12.1 Shipping Label Format:
AU OPTRONICS CORPORATION
Manufactured MM/WW
Model No: B101AW03 V0
AU Optroni cs
MADE IN CHI NA (S01)
C US
C US
C USC US
x x x x x x x
x x x x x x x
x x x x x x xx x x x x x x
Pb
RoHS
www.jxlcd.com
www.jxlcd.com
B101AW01 V0 (Document Version: 0.4)
29 of 35
12.2 Carton package:
www.jxlcd.com
www.jxlcd.com
Product Specification
AU OPTRONICS CORPORATION
B101AW01 V0 (Document Version: 0.4)
30 of 35
Product Specification
12.3 Shipping package of palletizing sequence:
AU OPTRONICS CORPORATION
www.jxlcd.com
www.jxlcd.com
B101AW01 V0 (Document Version: 0.4)
31 of 35
Product Specification
13. Appendix: EDID description
AU OPTRONICS CORPORATION
Address
HEX
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
FUNCTION Value
HEX
Header 00 00000000 0
FF 11111111 255
FF 11111111 255
FF 11111111 255
FF 11111111 255
FF 11111111 255
FF 11111111 255
00 00000000 0
EISA Manuf. Code LSB 06 00000110 6
Compressed ASCII AF 10101111 175
Product Code
hex, LSB first
32-bit ser # 00 00000000 0
00 00000000 0
00 00000000 0
D2 11010010 210
30 00110000 48
Value Value Note
BIN DEC
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
00 00000000 0
Week of manufacture 01 00000001 1
Year of manufacture 13 00010011 19
www.jxlcd.com
www.jxlcd.com
Video input def. (digital I/P, non-TMDS, CRGB)
Max H image size (rounded to cm)
Max V image size (rounded to cm)
Display Gamma (=(gamma*100)-100)
EDID Structure Ver. 01 00000001 1
EDID revision # 03 00000011 3
80 10000000 128
16 00010110 22
0D 00001101 13
78 01111000 120
Feature support (no DPMS, Active OFF, RGB, tmg
Blk#1)
Red/green low bits (Lower 2:2:2:2 bits)
Blue/white low bits (Lower 2:2:2:2 bits)
Red x (Upper 8 bits)
Red y/ highER 8 bits 59 01011001 89
Green x 57 01010111 87
Green y 91 10010001 145
Blue x 28 00101000 40
0A 00001010 10
66 01100110 102
95 10010101 149
96 10010110 150
20
21
22
23
B101AW01 V0 (Document Version: 0.4)
Blue y 1F 00011111 31
White x 50 01010000 80
White y 54 01010100 84
Established timing 1 00 00000000 0
32 of 35
Product Specification
24
AU OPTRONICS CORPORATION
Established timing 2 00 00000000 0
25
26
27
28
29
2A
2B
2C
2D
2E
2F
30
31
32
33
34
35
36
Pixel Clock/10000 LSB
Established timing 3 00 00000000 0
Standard timing #1 01 00000001 1
01 00000001 1
Standard timing #2 01 00000001 1
01 00000001 1
Standard timing #3 01 00000001 1
01 00000001 1
Standard timing #4 01 00000001 1
01 00000001 1
Standard timing #5 01 00000001 1
01 00000001 1
Standard timing #6 01 00000001 1
01 00000001 1
Standard timing #7 01 00000001 1
01 00000001 1
Standard timing #8 01 00000001 1
01 00000001 1
B0 10110000 176
37
Pixel Clock/10000 USB
38
Horz active Lower 8bits
39
Horz blanking Lower 8bits
www.jxlcd.com
www.jxlcd.com
3A
HorzAct:HorzBlnk Upper 4:4 bits
3B
3C
3D
3E
3F
40
41
42
43
44
45
46
47
48
Vertical Active Lower 8bits
Vertical Blanking Lower 8bits
Vert Act : Vertical Blanking (upper 4:4 bit)
HorzSync. Offset
HorzSync.Width
VertSync.Offset : VertSync.Width
Horz&Vert Sync Offset/Width Upper 2bits
Horizontal Image Size Lower 8bits
Vertical Image Size Lower 8bits
Horizontal & Vertical Image Size (upper 4:4 bits)
Horizontal Border (zero for internal LCD)
Vertical Border (zero for internal LCD)
Signal (non-intr, norm, no stero, sep sync, neg pol)
Detailed timing/monitor 00 00000000 0
13 00010011 19
00 00000000 0
40 01000000 64
41 01000001 65
58 01011000 88
19 00011001 25
20 00100000 32
18 00011000 24
88 10001000 136
31 00110001 49
00 00000000 0
DF 11011111 223
7D 01111101 125
00 00000000 0
00 00000000 0
00 00000000 0
18 00011000 24
49
4A
4B
B101AW01 V0 (Document Version: 0.4)
descriptor #2 00 00000000 0
00 00000000 0
0F 00001111 15
33 of 35
Product Specification
4C
AU OPTRONICS CORPORATION
00 00000000 0
4D
4E
4F
50
51
52
53
54
55
56
57
58
59
5A
5B
5C
5D
5E
00 00000000 0
00 00000000 0
00 00000000 0
00 00000000 0
00 00000000 0
00 00000000 0
00 00000000 0
00 00000000 0
00 00000000 0
00 00000000 0
00 00000000 0
00 00000000 0
20 00100000 32
Detailed timing/monitor 00 00000000 0
descriptor #3 00 00000000 0
00 00000000 0
FE 11111110 254
00 00000000 0
5F
60
61
62
63
64
65
66
67
68
69
6A
6B
6C
6D
6E
6F
70
Manufacture 41 01000001 65 A
Manufacture 55 01010101 85 U
www.jxlcd.com
www.jxlcd.com
Manufacture 4F 01001111 79 O
0A 00001010 10
20 00100000 32
20 00100000 32
20 00100000 32
20 00100000 32
20 00100000 32
20 00100000 32
20 00100000 32
20 00100000 32
20 00100000 32
Detailed timing/monitor 00 00000000 0
descriptor #4 00 00000000 0
00 00000000 0
FE 11111110 254
00 00000000 0
71
72
73
B101AW01 V0 (Document Version: 0.4)
Manufacture P/N 42 01000010 66 B
Manufacture P/N 31 00110001 49 1
Manufacture P/N 30 00110000 48 0
34 of 35
Product Specification
74
AU OPTRONICS CORPORATION
Manufacture P/N 31 00110001 49 1
75
76
77
78
79
7A
7B
7C
7D
7E
7F
Manufacture P/N 41 01000001 65 A
Manufacture P/N 57 01010111 87 W
Manufacture P/N 30 00110000 48 0
Manufacture P/N 33 00110011 51 3
Manufacture P/N 20 00100000 32
Manufacture P/N 56 01010110 86 V
Manufacture P/N 30 00110000 48 0
20 00100000 32
0A 00001010 10
Extension Flag 00 00000000 0
Checksum 52 01010010 82
SUM
SUM to HEX
6144
1800
www.jxlcd.com
www.jxlcd.com
B101AW01 V0 (Document Version: 0.4)
35 of 35
Loading...