Product Specification
) Preliminary Specifications
( V
( ) Final Specifications
Module 10.1” WSVGA Color TFT-LCD with LED Backlight design
AU OPTRONICS CORPORATION
Model Name
Note ( )
Customer Date
www.jxlcd.com
www.jxlcd.com
Checked &
Approved by
B101AW01 V0
LED Backlight with driving circuit design
Date
Approved by Date
Jerry Chen
Prepared by
07/15/2008
Note: This Specification is subject to change
without notice.
B101AW01 V0 (Document Version : 0.1)
Pei-Ching Huang
NBBU Marketing Division /
AU Optronics corporation
07/15/2008
1 of 37
Product Specification
AU OPTRONICS CORPORATION
Contents
1. Handling Precautions .......................................................................................4
2. General Description ..........................................................................................5
2.1 General Specification ......................................................................................................... 5
2.2 Optical Characteristics ....................................................................................................... 6
3. Functional Block Diagram .............................................................................. 11
4. Absolute Maximum Ratings ...........................................................................12
4.1 Absolute Ratings of TFT LCD Module.............................................................................. 12
4.2 Absolute Ratings of Environment..................................................................................... 12
5. Electrical characteristics ................................................................................13
5.1 TFT LCD Module.............................................................................................................. 13
5.2 Backlight Unit ................................................................................................................... 15
6. Signal Characteristic ......................................................................................16
6.1 Pixel Format Image .......................................................................................................... 16
6.2 The input data format....................................................................................................... 17
6.3 Integration Interface and Pin Assignment ........................................................................ 18
6.4 Interface Timing ............................................................................................................... 21
7. Connector Description.................................................................................... 24
7.1 TFT LCD Module.............................................................................................................. 24
www.jxlcd.com
www.jxlcd.com
8. LED Driving Specification ..............................................................................25
8.1 Connector Description ..................................................................................................... 25
8.2 Pin Assignment ................................................................................................................ 25
9. Vibration and Shock Test ...............................................................................26
9.1 Vibration Test ................................................................................................................... 26
9.2 Shock Test Spec: ............................................................................................................. 26
10. Reliability .......................................................................................................27
11. Mechanical Characteristics .......................................................................... 28
11.1 LCM Outline Dimension ................................................................................................. 28
11.2 Screw Hole Depth and Center Position.......................................................................... 30
12. Shipping and Package ..................................................................................31
12.1 Shipping Label Format................................................................................................... 31
12.2 Carton package.............................................................................................................. 32
12.3 Shipping package of palletizing sequence ..................................................................... 33
13. Appendix: EDID description .........................................................................34
B101AW01 V0 (Document Version : 0.1)
2 of 37
Product Specification
AU OPTRONICS CORPORATION
Record of Revision
Version and Date Page
0.1 2008/07/15 All First Edition for Customer
Old description New Description Remark
www.jxlcd.com
www.jxlcd.com
B101AW01 V0 (Document Version : 0.1)
3 of 37
Product Specification
1. Handling Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or
spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard
surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure
human earth when handling.
7) Do not open nor modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor
tilt the Interface Connector of the TFT Module.
AU OPTRONICS CORPORATION
10) After installation of the TFT Module into an enclosure (Notebook PC Bezel, for
example), do not twist nor bend the TFT Module even momentary. At designing the
enclosure, it should be taken into consideration that no bending/twisting forces are
applied to the TFT Module from outside. Otherwise the TFT Module may be
damaged.
11) Small amount of materials having no flammability grade is used in the LCD module.
The LCD module should be supplied by power complied with requirements of Limited
Power Source (IEC60950 or UL1950), or be applied exemption.
12) Disconnecting power supply before handling LCD modules, it can prevent electric
shock, DO NOT TOUCH the electrode parts, cables, connectors and LED circuit part
of TFT module that a LED light bar build in as a light source of back light unit. It can
prevent electrostic breakdown.
www.jxlcd.com
www.jxlcd.com
B101AW01 V0 (Document Version : 0.1)
4 of 37
Product Specification
Thickness
2. General Description
B101AW01 V0 is a Color Active Matrix Liquid Crystal Display composed of a TFT LCD panel, a
driver circuit, and LED backlight system. The screen format is intended to support the WSVGA
(1024(H) x 576(V)) screen and 262k colors (RGB 6-bits data driver) with LED backlight driving
circuit. All input signals are LVDS interface compatible.
B101AW01 V0 is designed for a display unit of notebook style personal computer and industrial
machine.
AU OPTRONICS CORPORATION
2.1 General Specification
The following items are characteristics summary on the table at 25 ℃ condition:
Items Unit Specifications
Screen Diagonal [mm] 255.54 (10.1 W”)
Active Area [mm] 222.72 x 125.28
Pixels H x V 1024 x 3(RGB) x 576
Pixel Pitch [mm] 0.2175 X 0.2175
Pixel Format R.G.B. Vertical Stripe
Display Mode Normally White
www.jxlcd.com
White Luminance (I
(Note: ILED is LED current)
Luminance Uniformity 1.25 max. (5 points)
Contrast Ratio 500:1 typ
Response Time [ms] 8 typ / 16 Max
www.jxlcd.com
LED
=20mA)
[cd/m2] 200 typ. (5 points average)
170 min. (5 points average)
Nominal Input Voltage VDD [Volt] +3.3 typ.
Power Consumption [Watt] 3.0 max. (Include Logic and Blu power)
Weight [Grams] 190 max.
Physical Size without inverter,
bracket.
Electrical Interface 1 channel LVDS
Surface Treatment Glare, Hardness 3H
Support Color 262K colors ( RGB 6-bit )
B101AW01 V0 (Document Version : 0.1)
[mm]
Min. Typ. Max.
Length 234.5 235.0 235.5
Width 142.5 143.0 143.5
- - 5.2
5 of 37
Product Specification
RoHS Compliance
Temperature Range
Operating
Storage (Non-Operating)
RoHS Compliance
2.2 Optical Characteristics
The optical characteristics are measured under stable conditions at 25℃ (Room Temperature) :
AU OPTRONICS CORPORATION
[oC]
[oC]
0 to +50
-20 to +60
Item Symbol
White Luminance
I
LED
=20mA
Viewing Angle
Luminance Uniformity
Luminance Uniformity
Contrast Ratio CR
Cross talk %
Response Time
Color /
Chromaticity
Coordinates
www.jxlcd.com
www.jxlcd.com
Red
Green
Blue
White
Conditions Min. Typ. Max. Unit Note
θR
θL
ψH
ψL
δ5P
δ
13P
Tr Rising
Tf Falling
TRT Rising + Falling
Rx
Ry
Gx
Gy
Bx
By
Wx
Wy
5 points average
Horizontal (Right)
CR = 10 (Left)
Vertical (Upper)
CR = 10 (Lower)
5 Points
13 Points
400 500 -
4
CIE 1931
170 200 - cd/m
40
40
10
30
- - 1.25
- - -
-
- - -
- 8 16
- TBD -
- TBD -
- TBD -
- TBD -
- TBD -
- TBD -
0.283 0.313 0.343
0.299 0.329 0.359
45
45
15
35
-
-
degree
-
-
-
-
msec
2
1, 4, 5.
4, 9
1, 3, 4
2, 3, 4
4, 6
4, 7
4, 8
4
NTSC %
B101AW01 V0 (Document Version : 0.1)
- 45 -
6 of 37
Product Specification
=
Maximum Brightness of thirteen points
Minimum Brightness of thirteen points
Maximum Brightness
of five
points
=
Minimum Brightness of five points
Note 1: 5 points position (Ref: Active area)
H /4
H /4
AU OPTRONICS CORPORATION
W / 4 W / 4 W / 4 W / 4
W
1 2
H
H /4
H /4
Note 2: 13 points position (Ref: Active area)
W /4
1 0
1 0
H /4
www.jxlcd.com
www.jxlcd.com
H /4
H
H /4
1
6
3
4
W
W /4
4 5
W /4
2
7
5
W /4
1 0
3
8
9
H /4
1 0
1 1
1 2
Note 3: The luminance uniformity of 5 or13 points is defined by dividing the maximum luminance values by the
minimum test point luminance
δ
W5
1 0
1 3
δ
Note 4: Measurement method
The LCD module should be stabilized at given temperature for 30 minutes to avoid abrupt temperature change
during measuring. In order to stabilize the luminance, the measurement should be executed after lighting Backlight
B101AW01 V0 (Document Version : 0.1)
W13
7 of 37
Product Specification
Field=2
°
Contrast ratio (CR)=
Brightness on the “White” state
Brightness on the “Black” state
AU OPTRONICS CORPORATION
for 30 minutes in a stable, windless and dark room, and it should be measured in the center of screen.
Photo detector
Note 5： Definition of Average Luminance of White (YL):
Measure the luminance of gray level 63 at 5 points，Y
L (x) is corresponding to the luminance of the point X at Figure in Note (1).
Note 6： Definition of contrast ratio:
Note 7： Definition of Cross Talk (CT)
CT = | YB – YA | / YA × 100 (%)
Where
www.jxlcd.com
www.jxlcd.com
Contrast ratio is calculated with the following formula.
= [L (1)+ L (2)+ L (3)+ L (4)+ L (5)] / 5
L
YA = Luminance of measured location without gray level 0 pattern (cd/m2)
YB = Luminance of measured location with gray level 0 pattern (cd/m2)
B101AW01 V0 (Document Version : 0.1)
8 of 37
Product Specification
Note 8: Definition of response time:
The output signals of BM-7 or equivalent are measured when the input signals are changed from “Black” to
“White” (falling time) and from “White” to “Black” (rising time), respectively. The response time interval between the
10% and 90% of amplitudes. Refer to figure as below.
AU OPTRONICS CORPORATION
"Black"
100%
S
i
90%
g
n
a
l
(
R
e
l
a
t
i
v
e
v
a
l
u
e
)
www.jxlcd.com
www.jxlcd.com
10%
0%
Tr
Tf
"White""White"
B101AW01 V0 (Document Version : 0.1)
9 of 37
Product Specification
Note 9. Definition of viewing angle
Viewing angle is the measurement of contrast ratio ≧10, at the screen center, over a 180° horizontal and
180° vertical range (off-normal viewing angles). The 180° viewing angle range is broken down as follows; 90° (θ)
horizontal left and right and 90° (Φ) vertical, high (up) and low (down). The measurement direction is typically
perpendicular to the display surface with the screen rotated about its center to develop the desired measurement
viewing angle.
AU OPTRONICS CORPORATION
www.jxlcd.com
www.jxlcd.com
B101AW01 V0 (Document Version : 0.1)
10 of 37
Product Specification
3. Functional Block Diagram
The following diagram shows the functional block of the 10.1 inches wide Color TFT/LCD 40 Pin (One
CH/connector Module)
AU OPTRONICS CORPORATION
www.jxlcd.com
www.jxlcd.com
B101AW01 V0 (Document Version : 0.1)
11 of 37
Product Specification
4. Absolute Maximum Ratings
An absolute maximum rating of the module is as following:
4.1 Absolute Ratings of TFT LCD Module
Item Symbol Min Max Unit Conditions
AU OPTRONICS CORPORATION
Logic/LCD Drive Voltage
Vin -0.3 +4.0 [Volt] Note 1,2
4.2 Absolute Ratings of Environment
Item Symbol Min Max Unit Conditions
Operating Temperature
Operation Humidity HOP 10 90 [%RH] Note 4
Storage Temperature
Storage Humidity HST
Note 1: At Ta (25℃ )
Note 2: Permanent damage to the device may occur if exceed maximum values
Note 3: LED specification refer to section 5.2
Note 4: For quality performance, please refer to AUO IIS (Incoming Inspection Standard).
www.jxlcd.com
www.jxlcd.com
TOP 0 +50 [oC] Note 4
TST -20 +60 [oC] Note 4
10 90
Twb=39°C
[%RH]
Note 4
Operating Range
B101AW01 V0 (Document Version : 0.1)
Storage Range
12 of 37
Product Specification
Voltage
-
90%
10%
5. Electrical characteristics
5.1 TFT LCD Module
5.1.1 Power Specification
Input power specifications are as follows;
The power specification are measured under 25 and frame frenquency under 60Hz℃
AU OPTRONICS CORPORATION
Symble Parameter Min Typ Max Units
VDD Logic/LCD Drive
PDD VDD Power
IDD IDD Current
I
Rush
Inrush Current
VDDrp Allowable
3.0 3.3 3.6 [Volt]
- 1.6 [Watt] Note 1/2
- 350
- -
- -
450
2000 [mA]
100 [mV]
Logic/LCD Drive
Ripple Voltage
Note 1 : Maximum Measurement Condition：Black Pattern
Note 2：Typical Measurement Condition: Mosaic Pattern
Note 3：Measure Condition
+5.0V
www.jxlcd.com
www.jxlcd.com
R1
47K
(High to Low)
Control
Signal
SW1
SW MAG-SPST
1 2
+12.0V
R2
1K
VR1
47K
D6
D5
D2 S
D1
G
C3
0.01uF/25V
Q3
AO6402
D2SD1D5
G
D6
Q3
AO6402
F1
[mA]
p-p
Note 1/2
Note 3
C1
1uF/16V
(LCD Module Input)
Note
VCC
C2
1uF/25V
3.3V
0V
0.5ms
Vin rising time
B101AW01 V0 (Document Version : 0.1)
13 of 37
Product Specification
Vth
VSS
Vtl
5.1.2 Signal Electrical Characteristics
Input signals shall be low or High-impedance state when VDD is off.
It is recommended to refer the specifications of THC63LVDF84A (Thine Electronics Inc.) in
detail.
Signal electrical characteristics are as follows;
AU OPTRONICS CORPORATION
Parameter
Vth
Vtl
Vcm
Note: LVDS Signal Waveform
Differential Input High
Threshold (Vcm=+1.2V)
Differential Input Low
Threshold (Vcm=+1.2V)
Differential Input
Common Mode Voltage
www.jxlcd.com
www.jxlcd.com
Condition Min Max Unit
Vcm
-
-100
0.6
100
-
1.4
[mV]
[mV]
[V]
B101AW01 V0 (Document Version : 0.1)
14 of 37
Product Specification
5.2 Backlight Unit
LED Parameter guideline for LED driving selection (Ref. Remark 1)
AU OPTRONICS CORPORATION
Parameter
LED Forward Voltage VF 2.95 3.15 3.4 [Volt]
LED Forward Current IF - 20 - [mA]
LED Power
consumption
LED Life-Time
Output PWM frequency
Duty ratio
Note 1: Calculator value for reference IF×VF =P
Note 2: The LED life-time define as the estimated time to 50% degradation of initial luminous.
www.jxlcd.com
www.jxlcd.com
Symbol
P
2.16
LED
N/A 10,000
F
PWM
-- 20 -- 100
Min Typ Max
- -
100 - 20K
Units Condition
[Watt]
Hour
Hz
%
(Ta=25 )℃
(Ta=25 )℃
(Ta=25 )℃
Note 1
(Ta=25 )℃
IF=20 mA
Note 2
B101AW01 V0 (Document Version: 0.1)
15 of 37
Product Specification
6. Signal Characteristic
6.1 Pixel Format Image
Following figure shows the relationship of the input signals and LCD pixel format.
AU OPTRONICS CORPORATION
www.jxlcd.com
www.jxlcd.com
B101AW01 V0 (Document Version: 0.1)
16 of 37
Product Specification
Data Clock
6.2 The input data format
Signal Name
R5
R4
R3
R2
R1
R0
Description
Red Data 5 (MSB)
Red Data 4
Red Data 3
Red Data 2
Red Data 1
Red Data 0 (LSB)
Red-pixel Data
AU OPTRONICS CORPORATION
Red-pixel Data
Each red pixel's brightness data consists of
these 6 bits pixel data.
G5
G4
G3
G2
G1
G0
B5
B4
B3
B2
B1
B0
RxCLKIN
DE Display Timing This signal is strobed at the falling edge of
VS Vertical Sync The signal is synchronized to RxCLKIN .
HS Horizontal Sync The signal is synchronized to RxCLKIN .
Note: Output signals from any system shall be low or High-impedance state when VDD is off.
Green Data 5 (MSB)
Green Data 4
Green Data 3
www.jxlcd.com
Green Data 2
www.jxlcd.com
Green Data 1
Green Data 0 (LSB)
Green-pixel Data
Blue Data 5 (MSB)
Blue Data 4
Blue Data 3
Blue Data 2
Blue Data 1
Blue Data 0 (LSB)
Blue-pixel Data
Green-pixel Data
Each green pixel's brightness data consists of
these 6 bits pixel data.
Blue-pixel Data
Each blue pixel's brightness data consists of
these 6 bits pixel data.
The signal is used to strobe the pixel data and
DE signals. All pixel data shall be valid at the
falling edge when the DE signal is high.
RxCLKIN. When the signal is high, the pixel
data shall be valid to be displayed.
B101AW01 V0 (Document Version: 0.1)
17 of 37
Product Specification
6.3 Integration Interface and Pin Assignment
LVDS is a differential signal technology for LCD interface and high speed data transfer device.
AU OPTRONICS CORPORATION
PIN# Signal Name
1 NC No Connection (Reserve)
2 AVDD PowerSupply,3.3V(typical)
3 AVDD PowerSupply,3.3V(typical)
4 DVDD DDC 3.3Vpower
5 NC No Connection (Reserve)
6 SCL DDCClock
7 SDA DDCData
8 Rin0- -LVDSdifferential data input(R0-R5,G0)
9 Rin0+ +LVDSdifferential data input(R0-R5,G0)
10 GND Ground
11 Rin1- -LVDSdifferential data input(G1-G5,B0-B1)
12 Rin1+ +LVDSdifferential data input(G1-G5,B0-B1)
13 GND Ground
14 Rin2- -LVDSdifferential data input(B2-B5,HS,VS,DE)
15 Rin2+ +LVDSdifferential data input(B2-B5,HS,VS,DE)
Description
16 GND Ground
17 ClkIN- -LVDSdifferential clock input
18 ClkIN+ +LVDSdifferential clock input
19 GND Ground–Shield
20 NC No Connection (Reserve)
21 NC No Connection (Reserve)
22 GND Ground–Shield
23 NC No Connection (Reserve)
24 NC No Connection (Reserve)
25 GND Ground–Shield
26 NC No Connection (Reserve)
27 NC No Connection (Reserve)
28 GND Ground–Shield
29 NC No Connection (Reserve)
30 NC No Connection (Reserve)
31
www.jxlcd.com
www.jxlcd.com
VLED_GND LED Ground
32
33
B101AW01 V0 (Document Version: 0.1)
VLED_GND LED Ground
VLED_GND LED Ground
18 of 37
Product Specification
AU OPTRONICS CORPORATION
34
35
36
37
38
39
40
NC No Connection (Reserve)
PWM System PWM Signal Input
LED_EN LED enable pin(+3V Input)
NC No Connection (Reserve)
VLED LED Power Supply 6V-21V
VLED LED Power Supply 6V-21V
VLED LED Power Supply 6V-21V
www.jxlcd.com
www.jxlcd.com
B101AW01 V0 (Document Version: 0.1)
19 of 37
Note1: Start from right side
Product Specification
AU OPTRONICS CORPORATION
Note2 : Input signals shall be low or High-impedance state when VDD is off.
Internal circuit of LVDS inputs are as following.
The module uses a 100ohm resistor between positive and negative data lines of each
receiver input.
www.jxlcd.com
www.jxlcd.com
B101AW01 V0 (Document Version: 0.1)
20 of 37
Product Specification
6.4 Interface Timing
6.4.1 Timing Characteristics
Basically, interface timings should match the 1024 x 576 /60Hz manufacturing guide line
timing.
Parameter Symbol Min. Typ. Max. Unit
Frame Rate - 50 60 - Hz
AU OPTRONICS CORPORATION
Clock frequency 1/ T
Vertical
Section
Horizontal
Section
Note : DE mode only
6.4.2 Timing diagram
DOTCLK
T
CLOCK
www.jxlcd.com
www.jxlcd.com
Input
Data
DE
DE
20 49.5 72 MHz
Clock
Period TV 584 614 1023
Active TVD - 576 -
Blanking TVB 8 38 447
Period TH 1054 1344 1424
Active THD - 1024 -
Blanking THB 30 320 400
Input Timing Definition ( DE Mode)
Invaild
Data
T
HB
Pixel
1
T
VB
Pixel
2
T
Pixel
3
T
HD
H
T
V
Pixel
N-1
T
Pixel
N
VD
T
Line
T
Clock
Invaild
Data
Pixel
1
B101AW01 V0 (Document Version: 0.1)
21 of 37
Product Specification
6.5 Power ON/OFF Sequence
VDD power on/off sequence is as follows. Interface signals are also shown in the chart. Signals
from any system shall be Hi-Z state or low level when VDD is off
AU OPTRONICS CORPORATION
Power Sequence Timing
www.jxlcd.com
www.jxlcd.com
Parameter
T1 0.5 - 10
T2 0 - 50
T3 0 - 50
T4 400 - -
T5 200 - -
T6 200 - -
T7 0 - 10
Min. Typ. Max.
Value
Units
ms
B101AW01 V0 (Document Version: 0.1)
22 of 37
Product Specification
LED on/off sequence is as follows. Interface signals are also shown in the chart.
AU OPTRONICS CORPORATION
Values
Symbol
T1
www.jxlcd.com
www.jxlcd.com
Note: The duty of LED dimming signal should be more than 20% in T2 and T3.
T2
T3
T4
T5
Min Typ Max
10 --- ---
10 --- ---
50 --- ---
0 --- ---
10 --- ---
Unit
ms
B101AW01 V0 (Document Version: 0.1)
23 of 37
Product Specification
7. Connector Description
Physical interface is described as for the connector on module.
These connectors are capable of accommodating the following signals and will be following
components.
7.1 TFT LCD Module
Connector Name / Designation For Signal Connector
Manufacturer IPEX
AU OPTRONICS CORPORATION
Type / Part Number
Mating Housing/Part Number
www.jxlcd.com
www.jxlcd.com
IPEX 20455-040E-12
IPEX 20453-040T-11
B101AW01 V0 (Document Version: 0.1)
24 of 37
Product Specification
8. LED Driving Specification
8.1 Connector Description
It is a intergrative interface and comibe into LVDS connector. The type and mating refer to
section 7.
8.2 Pin Assignment
Ref. to 6.3
AU OPTRONICS CORPORATION
www.jxlcd.com
www.jxlcd.com
B101AW01 V0 (Document Version: 0.1)
25 of 37
Product Specification
9. Vibration and Shock Test
9.1 Vibration Test
Test Spec:
Test method: Non-Operation
Acceleration: 1.5 G
Frequency: 10 - 500Hz Random
Sweep: 30 Minutes each Axis (X, Y, Z)
9.2 Shock Test Spec:
Test Spec:
Test method: Non-Operation
AU OPTRONICS CORPORATION
Acceleration: 220 G , Half sine wave
Active time: 2 ms
Pulse: X,Y,Z .one time for each side
www.jxlcd.com
www.jxlcd.com
B101AW01 V0 (Document Version: 0.1)
26 of 37
10. Reliability
Items
Temperature
Humidity Bias
High Temperature Operation
Low Temperature Operation
High Temperature Storage
Low Temperature Storage
Thermal Shock
Test
Product Specification
AU OPTRONICS CORPORATION
Required Condition Note
Ta= 40℃, 90%RH, 300h
Ta= 50℃, Dry, 300h
Ta= 0℃, 300h
Ta= 60℃, 35%RH, 300h
Ta= -20℃, 50%RH, 250h
Ta=-20℃to 60℃, Duration at 30 min, 100 cycles
ESD
Note1: According to EN 61000-4-2 , ESD class B: Some performance degradation allowed. No data lost
. Self-recoverable. No hardware failures.
Remark: MTBF (Excluding the LED): 30,000 hours with a confidence level 90%
www.jxlcd.com
www.jxlcd.com
Contact : ±8 KV
Air : ±15 KV
Note 1
B101AW01 V0 (Document Version: 0.1)
27 of 37
Product Specification
11. Mechanical Characteristics
11.1 LCM Outline Dimension
AU OPTRONICS CORPORATION
www.jxlcd.com
www.jxlcd.com
B101AW01 V0 (Document Version: 0.1)
28 of 37
Product Specification
AU OPTRONICS CORPORATION
www.jxlcd.com
www.jxlcd.com
B101AW01 V0 (Document Version: 0.1)
29 of 37
Product Specification
11.2 Screw Hole Depth and Center Position
Screw hole maximum depth, from side surface = 2.0 mm (See drawing)
Screw hole center location, from front surface = 2.8 ± 0.3mm (See drawing)
AU OPTRONICS CORPORATION
Screw Torque: Maximum 2.5 kgf-cm
www.jxlcd.com
www.jxlcd.com
B101AW01 V0 (Document Version: 0.1)
30 of 37
Product Specification
Week code
Model name
AU OPTRONICS CORPORATION
12. Shipping and Package
12.1 Shipping Label Format
H/W
www.jxlcd.com
www.jxlcd.com
B101AW01 V0 (Document Version: 0.1)
31 of 37
Product Specification
12.2 Carton package
The outside dimension of carton is 477 (L) mm x 375 (W) mm x 339 (H) mm
www.jxlcd.com
www.jxlcd.com
AU OPTRONICS CORPORATION
B101AW01 V0 (Document Version: 0.1)
32 of 37
Product Specification
12.3 Shipping package of palletizing sequence
AU OPTRONICS CORPORATION
www.jxlcd.com
www.jxlcd.com
B101AW01 V0 (Document Version: 0.1)
33 of 37
Product Specification
13. Appendix: EDID description
AU OPTRONICS CORPORATION
Address
HEX
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
FUNCTION Value
Value Value
Note
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
20
www.jxlcd.com
www.jxlcd.com
21
22
23
24
B101AW01 V0 (Document Version: 0.1)
34 of 37
Product Specification
25
AU OPTRONICS CORPORATION
26
27
28
29
2A
2B
2C
2D
2E
2F
30
31
32
33
34
35
36
37
38
39
3A
3B
3C
3D
3E
3F
40
41
42
43
44
45
46
47
48
49
www.jxlcd.com
www.jxlcd.com
4A
4B
4C
B101AW01 V0 (Document Version: 0.1)
35 of 37
Product Specification
4D
AU OPTRONICS CORPORATION
4E
4F
50
51
52
53
54
55
56
57
58
59
5A
5B
5C
5D
5E
5F
60
61
62
63
64
65
66
67
68
69
6A
6B
6C
6D
6E
6F
70
71
72
73
74
www.jxlcd.com
www.jxlcd.com
B101AW01 V0 (Document Version: 0.1)
36 of 37
Product Specification
75
76
77
78
AU OPTRONICS CORPORATION
79
7A
7B
7C
7D
7E
7F
www.jxlcd.com
www.jxlcd.com
B101AW01 V0 (Document Version: 0.1)
37 of 37
Loading...