() Preliminary Specification
(V) Final Specification
Product Specification
AU OPTRONICS CORPORATION
A150XN01 V.2
Module
Model Name
15” XGA TFT-LCD Module
A150XN01 V.2
Customer Date
www.jxlcd.com
www.jxlcd.com
Approved by
Checked &
Approved by
JC Fan
Prepared by Date
Date
02/04/2009
Note: This Specification is subject to change
without notice.
document version 0.3 1/25
PDF created with pdfFactory Pro trial version www.pdffactory.com
Joyce Kuo
Audio-Video Display Business Unit /
AU Optronics corporation
02/04/2009
Product Specification
AU OPTRONICS CORPORATION
A150XN01 V.2
Contents
1. Handling Precautions..............................................................................................................4
2. General Description.................................................................................................................5
2.1 Display Characteristics...................................................................................................................5
3. Functional Block Diagram.......................................................................................................7
4. Absolute Maximum Ratings....................................................................................................8
4.1 Absolute Ratings of TFT LCD Module...........................................................................................8
4.2 Absolute Ratings of Backlight Unit.................................................................................................8
5. Electrical characteristics.........................................................................................................9
5.1 TFT LCD Module..........................................................................................................................9
6. Signal Characteristic.............................................................................................................11
6.1 Pixel Format Image.......................................................................................................................11
6.2 The Input Data Format..................................................................................................................12
6.3 Signal Description.........................................................................................................................13
6.4 Interface Timing............................................................................................................................15
6.5 Color Input Data Reference...........................................................................................................17
6.6 Power ON/OFF Sequence.............................................................................................................18
7. Connector & Pin Assignment...............................................................................................19
7.1 TFT LCD Module.........................................................................................................................19
7.2 Backlight Unit...............................................................................................................................20
8. Reliability Test.......................................................................................................................21
9. Outline Drawing.....................................................................................................................22
10. Lot definition........................................................................................................................24
10.1 Lot definition of product (Product Label)....................................................................................24
10.2 Lot definition of part (BLU Label)..............................................................................................24
11. Packing Form.......................................................................................................................25
www.jxlcd.com
www.jxlcd.com
document version 0.3 2/25
PDF created with pdfFactory Pro trial version www.pdffactory.com
Product Specification
A150XN01 V.2
AU OPTRONICS CORPORATION
Record of Revision
Version and Date Page
0.0 2008/07/18 All First Draft All
0.1 2008/08/22
0.2 2008/12/01
5
6
9
22~23
24
5
6
8
9
13,19
22~23
24
5
6
8
Power consumption and Weight
Chromaticity and Note 1
IDD and PDD
Outline Drawing
Packing Form
LED 9.9W (Typ)
Chromaticity: Green
4.2 Absolute Ratings of Backlight Unit
Value of IDD/Irush/Pdd
19 and 20 pin
Outline drawing
Packing Form
White Luminance and LED power consumption
Condition of Luminance and note 1
LED input current
Old description New Description
Updated
Updated
Updated
Updated
Added
LED 13.125W (Typ)
Updated
Updated
Updated
Exchanged
Updated
Updated
Updated
Updated
Updated
0.3 2009/01/23
10~11
www.jxlcd.com
21
www.jxlcd.com
24
5.1.2 table and note 2
Condition of Mechanical shock
Packing Form
Updated
1 times for each direction
Updated
5
6
7
Optical response time: 8 ms
Optical response time
LED condition
Functional Block Diagram
Optical response time: 12 ms
Updated
Updated
Updated
0.4 2009/02/04
8
11
24
4.2 Absolute Ratings of Backlight Unit
5.1.3 BLU unit
10. Lot definition
Remove typ. Value
Add remark
Added
Added
document version 0.3 3/25
PDF created with pdfFactory Pro trial version www.pdffactory.com
Product Specification
AU OPTRONICS CORPORATION
A150XN01 V.2
1. Handling Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth when
handling.
7) Do not open or modify the Module Assembly.
8) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the Interface
Connector of the TFT Module.
9) After installation of the TFT Module into an enclosure, do not twist nor bend the TFT Module even
momentary. At designing the enclosure, it should be taken into consideration that no bending/twisting
forces are applied to the TFT Module from outside. Otherwise the TFT Module may be damaged.
www.jxlcd.com
www.jxlcd.com
document version 0.3 4/25
PDF created with pdfFactory Pro trial version www.pdffactory.com
Product Specification
Active Area
[mm]
304.128 (H) x 228.096
Pixels H x V
1024 (RGB) x 768
Pixel Pitch
[mm]
0.297 (per one triad) x 0.297
Pixel Arrangement
R.G.B. Vertical Stripe
Display Mode
TN mode, Normally White
White Luminance
[cd/m2]
350 (Typ)
@ 100
mA/LED
Contrast Ratio
700 Optical ResponseTime
[msec]
12
(Typ, on/off)
Nominal Input Voltage VDD
[Volt]
+3.3 (Typ)
Electrical Interface
one Channel LVDS
Surface Treatment
Anti-glare type, Hardness 3H
Support Colors
16.2M colors (RGB 6
-
bits+FRC)
RoHS Compliance
RoHS Compliance
AU OPTRONICS CORPORATION
A150XN01 V.2
2. General Description
This specification applies to the 15 inch Color TFT-LCD module A150XN01 V2
The display supports the XGA (1024(H) x 768(V)) screen format and 16.2M colors. All input signals are 1 Channel LVDS
interface compatible.
.
2.1 Display Characteristics
The following items are characteristics summary on the table under 25 ℃ condition:
Items Unit Specifications
Power Consumption
www.jxlcd.com
(VDD line + LED line)
Weight [Grams] 970
Physical Size (H x V x D) [mm] 326 (W) x 252(H) x 11.5(D) (Max)
www.jxlcd.com
[Watt] LED 10.5W (Typ)
VDD 1.65W(Typ) , Black Pattern
document version 0.3 5/25
PDF created with pdfFactory Pro trial version www.pdffactory.com
Product Specification
50 %
90 %
50 %
10 %
10 %
AU OPTRONICS CORPORATION
A150XN01 V.2
2.2 Optical Characteristics
The optical characteristics are measured under stable conditions at 25 (Room Temperature)℃ .
Item Unit Conditions Min. Typ. Max. Note
Horizontal (Right)
Viewing Angle [degree]
Luminance Uniformity [%] 9 Points 70 - 2
Optical Response Time [msec]
Color / Chromaticity
Coordinates
(CIE 1931)
www.jxlcd.com
www.jxlcd.com
CR = 10 (Left)
Vertical (Up)
CR = 10 (Down)
Rising - 8 11
Falling - 4 6
Rising + Falling - 12 17
White x 0.26 0.31 0.36
White y 0.28 0.33 0.38
Red x 0.59 0.64 0.69
Red y 0.29 0.34 0.39
Green x 0.27 0.32 0.37
Green y 0.55 0.60 0.65
Blue x 0.09 0.14 0.19
Blue y 0.01 0.06 0.11
60
60
55
50
70
-
70
65
-
60
1
White Luminance
(At LED=500mA)
Contrast Ratio 450 700 -
Optical Equipment: BM-5A, BM-7, PR880, or equivalent
Note 1: Ambient temperature =25℃. And LED forward current IL = 500 mA. To be measured in the dark room
below 10 Lux and to be measured on the center area of panel with a viewing cone of 1°by Topcon
luminance meter BM-7, after 10 minute operation.
Note 2: Luminance Uniformity of these 9 points is defined as below:
document version 0.3 6/25
[cd/m2 ] 300 350 - 1
PDF created with pdfFactory Pro trial version www.pdffactory.com
Product Specification
C
onn
e
c
t
o
r
LVDS
I/F + X
-
PCB
Y
-Dr
i
v
e
r
IC
AU OPTRONICS CORPORATION
A150XN01 V.2
3. Functional Block Diagram
The following diagram shows the functional block of the 15.0 inches wide Color TFT-LCD Module:
+3.3V
DC/DC
Converter
www.jxlcd.com
www.jxlcd.com
AUO ASIC
LVDS
Receiver
Timing
Controller
Gamma
Correction
G1
TFT-LCD
1024(x3) x 768
Pixels
D1 D3072
G768
Backlight
Backlight
connector
document version 0.3 7/25
PDF created with pdfFactory Pro trial version www.pdffactory.com
Product Specification
AU OPTRONICS CORPORATION
4. Absolute Maximum Ratings
Absolute maximum ratings of the module are as follows:
4.1 Absolute Ratings of TFT LCD Module
Item Symbol Min. Max. Unit Conditions
A150XN01 V.2
Logic/LCD Drive Voltage
VDD -0.3 +4.0 [Volt]
4.2 Absolute Ratings of Backlight Unit
Item Symbol Min. Max. Unit Remark
VLED voltage input VLED 24 V
VLED current input ILED mA
LED Life Time 10,000 Ambient temperature =25℃
www.jxlcd.com
www.jxlcd.com
document version 0.3 8/25
PDF created with pdfFactory Pro trial version www.pdffactory.com
Product Specification
at 60Hz
Vin rising time
0V
3.3V
470 us
+3.3V
A150XN01 V.2
AU OPTRONICS CORPORATION
5. Electrical characteristics
5.1 TFT LCD Module
5.1.1 Power Specification
Input power specifications are as follows:
Symble Parameter Min. Typ. Max. Unit Condition
VDD
Logic/LCD Drive
Voltage
3.0 3.3 3.6 [Volt]
IDD VDD current - 600 - [mA]
±10%
Vin=3.3V , Black Pattern,
at 60Hz
Irush LCD Inrush Current - 800 - [mA] Vin rising time = 470us
PDD VDD Power
Note: Measurement conditions:
+5.0V
R1
47K
www.jxlcd.com
www.jxlcd.com
(High to Low)
Control Signal
SW
+12.0V
R2
1K
D6
D5
D2 S
D1
G
C3
Q3
AO6402
D2SD1D5
1.98 - [Watt]
F1
G
D6
Q3
AO6402
Vin=3.3V , Black Pattern,
VCC
(LCD Module Input)
C1
1uF/16V
C2
1uF/25V
VR1
47K
0.01uF/25V
document version 0.3 9/25
PDF created with pdfFactory Pro trial version www.pdffactory.com
Product Specification
VSS
VICM
VTL VTH
VID
︱
AU OPTRONICS CORPORATION
A150XN01 V.2
5.1.2 Signal Electrical Characteristics
Input signals shall be low or Hi-Z state when Vin is off
It is recommended to refer the specifications of SN75LVDS82DGG (Texas Instruments) in detail.
Each signal characteristics are as follows;
Symbol Parameter Min Typ Max Units Condition
VTH
VTL
│VID│
VICM
tRMG
tRIP1 Input data position 0 |tRMG| 0.0 |tRMG|
tRIP0 Input data position 1
tRIP6 Input data position 2
tRIP5 Input data position 3
tRIP4 Input data position 4
tRIP3 Input data position 5
Differential Input
High Threshold
Differential Input
Low Threshold
Input Differential
Voltage
Differential Input
Common Mode
Voltage
CLKIN-/+ = 85MHz
CLK IN-/+ = 65MHz
www.jxlcd.com
www.jxlcd.com
- - 100 [mV]
-100 - - [mV]
250 350 450 [mV]
1.0 1.25 2 [V]
-0.4
-0.6
T/7 - |tRMG| T/7 T/7 + |tRMG|
2T/7 - |tRMG|
3T/7 - |tRMG| 3T/7 3T/7 + |tRMG|
4T/7 - |tRMG| 4T/7 4T/7 + |tRMG|
5T/7 - |tRMG|
-
-
2T/7 2T/7 + |tRMG|
5T/7 5T/7 + |tRMG|
0.4
0.6
VICM = 1.2V
Note1
VICM = 1.2V
Note1
Note1
VTH/VTL = ± 100mV
Note1
Receiver data input margin
ns
Note2
ns Note2
tRIP2 Input data position 6
Note1: LVDS Signal Waveform
document version 0.3 10/25
6T/7 - |tRMG| 6T/7 6T/7 + |tRMG|
｜
PDF created with pdfFactory Pro trial version www.pdffactory.com
Product Specification
AU OPTRONICS CORPORATION
Note2: LVDS Input Signal For Timing Specification
5.1.3 Backlight unit
Item Symbol Min. Typ. Max. Unit
A150XN01 V.2
VLED voltage input VLED 21 24 V
VLED current input ILED 500 mA
6. Signal Characteristic
6.1 Pixel Format Image
Following figure shows the relationship of the input signals and LCD pixel format.
www.jxlcd.com
www.jxlcd.com
document version 0.3 11/25
PDF created with pdfFactory Pro trial version www.pdffactory.com
6.2 The Input Data Format
CLKIN+
CLKIN-
Product Specification
AU OPTRONICS CORPORATION
A150XN01 V.2
RIN0 +/-
RIN1 +/-
RIN2 +/-
RIN3 +/-
OG0 OR5OR4OR3OR2OR1OR0
OB0 OG3OG4OG1OG2OB1 OG5
DEVSHS
Rsvd
Current Cycle
Note1: Please follow PSWG.
Note2: 8-bit in
Note3: R/G/B data 7:MSB, R/G/B data 0:LSB
www.jxlcd.com
www.jxlcd.com
OB5OB3OB4OB2
OR7OB7 OR6OB6 OG7OG6
document version 0.3 12/25
PDF created with pdfFactory Pro trial version www.pdffactory.com
Product Specification
AU OPTRONICS CORPORATION
A150XN01 V.2
6.3 Signal Description
The module using a pair of LVDS receiver SN75LVDS82(Texas Instruments) or compatible. LVDS is a differential signal
technology for LCD interface and high speed data transfer device. Transmitter shall be SN75LVDS83(negative edge
sampling) or compatible. The first LVDS port(RxOxxx) transmits odd pixels while the second LVDS port(RxExxx) transmits
even pixels.
DF14H-20P-1.25H (HIROSE)
Pin No. Symbol Description
1 VDD Power Supply, 3.3V (typical)
2 VDD Power Supply, 3.3V (typical)
3 VSS Ground
4 VSS Ground
5 Rin0- - LVDS differential data input (R0-R5, G0)
6 Rin0+ + LVDS differential data input (R0-R5, G0)
7 VSS Ground
8 Rin1- - LVDS differential data input (G1-G5, B0-B1)
9 Rin1+ + LVDS differential data input (G1-G5, B0-B1)
10 VSS Ground
11 Rin2- - LVDS differential data input (B2-B5, HS, VS, DE)
12 Rin2+ + LVDS differential data input (B2-B5, HS, VS, DE)
13 VSS Ground
14 ClkIN- - LVDS differential clock input
15 ClkIN+ + LVDS differential clock input
16 VSS Ground
17 Rin3- - LVDS differential data input (R6-R7, G6-G7,B6-B7)
18 Rin3+ - LVDS differential data input (R6-R7, G6-G7,B6-B7)
19 RL/UD
20 SEL LVDS
www.jxlcd.com
www.jxlcd.com
H: 180 degree rotation
L: Normal mode
H: NS alike
L: Thine alike (Note 1)
document version 0.3 13/25
PDF created with pdfFactory Pro trial version www.pdffactory.com
Note 1 :
Product Specification
AU OPTRONICS CORPORATION
(a) NS alike
A150XN01 V.2
www.jxlcd.com
www.jxlcd.com
(b)Thine alike
document version 0.3 14/25
PDF created with pdfFactory Pro trial version www.pdffactory.com
Product Specification
AU OPTRONICS CORPORATION
6.4 Interface Timing
6.4.1 Timing Characteristics
Signal Item Symbol Min Typ Max Unit
Clock Timing
Hsync Timing
Vsync Timing
Note: DE mode only
Note: Typical value refer to VESA STANDARD
www.jxlcd.com
Clock frequency Tclk 50 65 81 MHz
Horizontal active Tdisp(h) 1024 1024 1024 Tclk
Horizontal blanking Tblk(h) 30 320 1024 Tclk
Horizontal period Th 1054 1344 2048 Tck
Vertical active Tdisp(v) 768 768 768 Th
Vertical blanking Tblk(v) 8 38 256 Th
Vertical period Tv 776 806 1024 Th
www.jxlcd.com
A150XN01 V.2
document version 0.3 15/25
PDF created with pdfFactory Pro trial version www.pdffactory.com
6.4.2 Timing Diagram
Product Specification
AU OPTRONICS CORPORATION
A150XN01 V.2
www.jxlcd.com
www.jxlcd.com
document version 0.3 16/25
PDF created with pdfFactory Pro trial version www.pdffactory.com
Product Specification
AU OPTRONICS CORPORATION
6.5 Color Input Data Reference
A150XN01 V.2
Color Data Reference
www.jxlcd.com
www.jxlcd.com
document version 0.3 17/25
PDF created with pdfFactory Pro trial version www.pdffactory.com
Product Specification
T5 T2
T1
T6
AU OPTRONICS CORPORATION
A150XN01 V.2
6.6 Power ON/OFF Sequence
Vin power and lamp on/off sequence is as follows. Interface signals are also shown in the chart. Signals from any
system shall be Hi-Z state or low level when Vin is off.
VALID
DATA
Value
90%
10%
T7
T4
Unit
Power Supply VDD
LVDS Signal
Backlight On
Parameter
90%
10%
T3
www.jxlcd.com
www.jxlcd.com
Power Sequence Timing
Min. Typ. Max.
T1 0.5 - 10 [ms]
T2 30 40 50 [ms]
T3 200 - - [ms]
T4 100 - - [ms]
T5 0 16 50 [ms]
T6 - - 10 [ms]
T7 1000 - - [ms]
document version 0.3 18/25
PDF created with pdfFactory Pro trial version www.pdffactory.com
Product Specification
AU OPTRONICS CORPORATION
A150XN01 V.2
7. Connector & Pin Assignment
Physical interface is described as for the connector on module.These connectors are capable of accommodating
the following signals and will be following components.
7.1 TFT LCD Module
7.1.1 Connector
Connector Name / Designation Interface Connector / Interface card
Manufacturer HIROSE
Type Part Number HRS DF14H-20P-1.25H (56)
7.1.2 Pin Assignment
Pin# Signal Name Pin# Signal Name
1
3
5
7
9
11
13
15
17
19
document version 0.3 19/25
www.jxlcd.com
www.jxlcd.com
VDD
VSS
Rin0-
VSS
Rin1+
Rin2-
VSS
ClkIN+
Rin3-
RL/UD
2 VDD
4 VSS
6
8 Rin110 VSS
12 Rin2+
14
16 VSS
18 Rin3+
20 SEL LVDS
Rin0+
ClkIN-
PDF created with pdfFactory Pro trial version www.pdffactory.com
Product Specification
AU OPTRONICS CORPORATION
A150XN01 V.2
7.2 Backlight Unit
Physical interface is described as for the connector on module. These connectors are capable of
accommodating the following signals and will be following components.
7.2.1 Connector
Connector Name / Designation Lightbar Connector / Backlight Lightbar
Manufacturer JST
Type Part Number PHR-2
7.2.2 Pin Assignment
Pin# Signal Name Pin # Signal Name
1
www.jxlcd.com
www.jxlcd.com
Power
2 GND
document version 0.3 20/25
PDF created with pdfFactory Pro trial version www.pdffactory.com
Product Specification
1 corner, 3 edges, 6 surfaces
AU OPTRONICS CORPORATION
A150XN01 V.2
8. Reliability Test
Environment test conditions are listed as following table.
No. Test items Conditions Remark
1 High temperature storage
2 Low temperature storage
3 High temperature operation
4 Low temperature operation
5 High temperature and high humidity
6 Thermal shock
7 Vibration
8 Mechanical shock
9 Vibration (with carton)
www.jxlcd.com
www.jxlcd.com
Ta= 70℃
Ta= -20℃
Tp= 70℃
Ta= 0℃
Tp= 50℃, 80% RH
-20°C to +60°C, Ramp ≤20°C/min,
Duration at Temp. = 30min, Test Cycles =
Frequency range : 8~33.3Hz
Stoke : 1.3mm
Sweep : 3.0G, 33.3 ~ 400Hz
Cycle : 15 minutes
2 hours for each direction of X,Z
4 hours for Y direction
100G, 6ms, ±X,±Y,±Z
1 times for each direction
Random vibration:
0.015G2/Hz from 5~200Hz
–6dB/octave from 200~500Hz
240Hrs
240Hrs
240Hrs
240Hrs
240Hrs Operation
Non-operation
JIS D1601,
A-10
Condition A
JIS C0041,
A-7
Condition C
IEC 68-34
10 Drop (with carton)
11 Electro Static discharge (ESD)
Note 1: The TFT-LCD module will not sustain damage after being subjected to 100 cycles of rapid temperature
change. A cycle of rapid temperature change consists of varying the temperature from -10℃ to 80℃,
and back again. Power is not applied during the test. After temperature cycling, the unit is placed in
normal room ambient for at least 4 hours before power on.
Note 2: According to EN61000-4-2 , ESD class B: Some performance degradation allowed. No data lost.
Self-recoverable. No hardware failures.
document version 0.3 21/25
Height: 60cm
Contact Discharge: ±8KV, 150pF(330Ω )
1sec, 8 points, 25 times/ point.
Air Discharge: ± 15KV, 150pF(330Ω )
1sec, 8 points, 25 times/ point.
JIS Z0202
Operation &
Non-operation
PDF created with pdfFactory Pro trial version www.pdffactory.com
9. Outline Drawing
Product Specification
AU OPTRONICS CORPORATION
A150XN01 V.2
www.jxlcd.com
www.jxlcd.com
document version 0.3 22/25
PDF created with pdfFactory Pro trial version www.pdffactory.com
Product Specification
AU OPTRONICS CORPORATION
A150XN01 V.2
www.jxlcd.com
www.jxlcd.com
document version 0.3 23/25
PDF created with pdfFactory Pro trial version www.pdffactory.com
Product Specification
AU OPTRONICS CORPORATION
A150XN01 V.2
10. Lot definition
10.1 Lot definition of product (Product Label)
10.1.1 Example lot number
10.1.2 Manufactured end of year and week mark
www.jxlcd.com
a. Manufactured end of year mark
Mark 05 06 07 08 …
Definition 2005 2006 2007 2008 …
b. Manufactured week mark
Mark 01 02 …
Definition 1st Week 2nd Week …
www.jxlcd.com
10.2 Lot definition of part (BLU Label)
10.1.1 Example lot number
document version 0.3 24/25
PDF created with pdfFactory Pro trial version www.pdffactory.com
11. Packing Form
Product Specification
AU OPTRONICS CORPORATION
www.jxlcd.com
www.jxlcd.com
A150XN01 V.2
document version 0.3 25/25
PDF created with pdfFactory Pro trial version www.pdffactory.com
Loading...