A. General Information.............................................................................................................................. 3
B. Outline Dimension................................................................................................................................. 4
E.Reliability Test Items .................................................................................................................................14
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PAPER SHALL NOT BE REPRODUCED, COPIED,
OR TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM AU OPTRONICS CORP.
Version: 0.0
A. General Information
This product is for Netbook application. This product is include cell, POL, driver IC, and FPC.
NO. Item Unit Specification Remark
1 Screen Size inch 10.1 (Diagonal)
2 Display Resolution dot 1024 (H)×600 RGB (V)
3 Overall Dimension mm 230.36(H) × 134(V) × 1.28(T) Note 1
4 Active Area mm 222.72(H)×125.28(V)
5 Pixel Pitch mm 0.2175(H)×0.2088(V)
6 Color Configuration -- R. G. B. Stripe
7 Color Depth -- 262K Colors Note 2
8 NTSC Ratio % 45
9 Display Mode -- Normally White
10 Panel surface Treatment -- 3H
11 Weight g
Page: 3/33
93g±10%
12 Panel Power Consumption W --
13 Viewing direction 6 o’clock (gray inversion)
Note 1: Not include blacklight cable and FPC. Refer next page to get further information.
Note 2: The full color display depends on 18-bit data signal (pin 4~27).
www.jxlcd.com
www.jxlcd.com
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PAPER SHALL NOT BE REPRODUCED, COPIED,
OR TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM AU OPTRONICS CORP.
Version: 0.0
B. Outline Dimension
1. TFT-LCD Module
Page: 4/33
www.jxlcd.com
www.jxlcd.com
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PAPER SHALL NOT BE REPRODUCED, COPIED, OR TRANSFORMED TO ANY OTHER FORMS
WITHOUT PERMISSION FROM AU OPTRONICS CORP.
Product Specification
AU OPTRONICS CORPORATION
C. Electrical Specifications
1. FPC Pin Assignment
Pin no Symbol I/O Description
1 DUMMY- Not connect
2 VCOMP VCOM signal
3 VCOMP VCOM signal
4 RESCUE2- RESCUE signal
5 YDIOI/O Gate start pulse input/output
6 YDIOI/O Gate start pulse input/output
7 VEEP Gate driver negative power supply
8 VEEP Gate driver negative power supply
9 VEEP Gate driver negative power supply
10 VGGP Gate driver positive power supply
11 VGGP Gate driver positive power supply
12 VGGP Gate driver positive power supply
13 YVCCAP Gate driver digital power
14 GNDG Ground
15 GNDG Ground
16 YOEI/O Input/Output pin for the output global on control.
17 YOEI/O Input/Output pin for the output enable control.
18 YOEI/O Input/Output pin for the output enable control.
19 XONI/O Input/Output pin for the output global on control.
20 YOEI/O Input/Output pin for the output global on control.
21 YOEI/O Input/Output pin for the output global on control.
22 YDIOI/O Gate start pulse input/output
23 YDIOI/O Gate start pulse input/output
24 VCST- The internal bypass paths
25 Comp1O Comp1 signal
26 RESCUE2- RESCUE signal
www.jxlcd.com
www.jxlcd.com
27 PAVDDP Positive Power supply for analog circuit.
28 PAVDDP Positive Power supply for analog circuit.
29 GNDG Ground
30 GNDG Ground
31 NAVDDP Negative Power supply for analog circuit.
32 NAVDD
33 RPENI RPEN Function
34 AGBSENI Enter aging Mode
A101SW01 V0 (Document Version: 0.3)
P
Negative Power supply for analog circuit.
From【液晶之家】—
5 of 33
Product Specification
AU OPTRONICS CORPORATION
35 GOAINV
36 PWMINI Input PWM signal
37 RESETI Global Reset
38 TEST
I
-
GOA mode enable control pin
Test Pin
39 SRC0I
40 SRC1I
I
41 CS0
42 CS1I
43 DCRENI Dynamic Contrast Ratio Enable Control
44 PWMI B/L Dimming
45 EPWPI EEPROM write protect
46 EXSCLI/O External I2C Master Clock, Max. 400KHz
47 EXSDAI/O External I2C Serial Data, Max. 400KHz
48 INSCLI/O Internal I2C Master Clock, Max. 400KHz
49 INSDAI/O Internal I2C Serial Data, Max. 400KHz
50 NAVDDP Negative Power supply for analog circuit.
51 NAVDDP Negative Power supply for analog circuit.
52 GNDG Ground
53 GNDG Ground
54 VGMA14I Gamma reference voltage.
73 RXIN0NI LVDS input RGB data
74 VDDP power supply for ASIC
75 VDDP power supply for ASIC
76 VDD_18V_LO IC internal regulator output,
77 VDD_18VO IC internal regulator output,
78 VPPI OTP Program Power Input
79 VGMA7I Gamma reference voltage.
80 VGMA6I Gamma reference voltage.
81 VGMA5I Gamma reference voltage.
82 VGMA4I Gamma reference voltage.
83 VGMA3I Gamma reference voltage.
84 VGMA2I Gamma reference voltage.
85 VGMA1I Gamma reference voltage.
86 PAVDDP Positive Power supply for analog circuit.
87 PAVDDP Positive Power supply for analog circuit.
88 GNDG Ground
89 GNDG Ground
90 VDDNO IC internal regulator output,
91 VDDP power supply for ASIC
92 VDDP power supply for ASIC
93 YV1CO Gate Pulse Modulation
94 YV1CO Gate Pulse Modulation
95 XSTBO Data latch control signal for source driver
96 XPOLO Polarity inversion signal for source driver
97 XDIOO XData Sampling start signal
98 NAVDDP Negative Power supply for analog circuit.
99 NAVDDP Negative Power supply for analog circuit.
100 GNDG Ground
101 GNDG Ground
102 PAVDDP Positive Power supply for analog circuit.
www.jxlcd.com
www.jxlcd.com
103 PAVDDP Positive Power supply for analog circuit.
104 RESCUE1- RESCUE signal
105 Comp2O Comp2 signal
106 VCST- The internal bypass paths
107 VCOMP VCOM signal
108 VCST- The internal bypass paths
109 VCST- The internal bypass paths
110 RESCUE1- RESCUE signal
111 VCOMP VCOM signal
A101SW01 V0 (Document Version: 0.3)
From【液晶之家】—
7 of 33
Product Specification
AU OPTRONICS CORPORATION
112 VCOMP VCOM signal
113 Dummy- Not connect
www.jxlcd.com
www.jxlcd.com
A101SW01 V0 (Document Version: 0.3)
From【液晶之家】—
8 of 33
2. Absolute Maximum Ratings
Product Specification
AU OPTRONICS CORPORATION
Item Symbol Condition
XVCC GND=0 -0.3 2.5 V
YVCCA GND=0 -0.3 2.5 V
Power voltage
AVDD,
VTOP
VEE –
VGG
VGMA1~
VGMA7
Gamma voltage
VGMA8~
VGMA14
Input signal voltage Data GND=0 -0.5 XVCC+0.5 V Digital signals
AGND=0 -0.5 +5.56 V Analog power supply
GND=0 VEE-0.3 VGG+0.3 V
AGND = 0
AGND = 0
Min. Max. Unit
-- -- V
-- -- V
Remark
Source driver digital
power supply
Gate driver digital
power supply
Gate driver supply
voltage
Gamma reference
voltage
Note 1: Functional operation should be restricted under ambient temperature (25℃).
Note 2: Maximum ratings are those values beyond which damages to the device may occur.
Functional operation should be restricted to the limits in the Electrical Characteristics chapter.
www.jxlcd.com
www.jxlcd.com
A101SW01 V0 (Document Version: 0.3)
From【液晶之家】—
9 of 33
Product Specification
AU OPTRONICS CORPORATION
3. Electrical DC Characteristics
a. Typical Operation Condition (AGND =GND = 0V)
Item Symbol Min. Typ. Max. Unit
XVCC 2.3 3.3 3.6 V Source driver digital power supply
YVCCA 2.3 3.3 3.6 V Gate driver digital power supply
Power voltage
Gamma voltage
AVDD,
5.56 V Analog power supply
VTOP
VGL -10 V
VGH 16V V
VGMA1 - V
VGMA2 - V
VGMA3 - V
VGMA4 - V
VGMA5 - V
VGMA6 - V
VGMA7 - V
VGMA8 - V
Remark
Gate driver supply voltage
Gamma reference voltage
(Preliminary only)
High level input
voltage
Low level input
voltage
VCOM VCOM 2.75 V
VGMA9 - V
www.jxlcd.com
www.jxlcd.com
VGMA10 - V
VGMA11 - V
VGMA12 - V
VGMA13 - V
VGMA14 - V
VIH 0.7*XVCC
VIL 0 - 0.3*XVCC V
- XVCC V
Digital signals
A101SW01 V0 (Document Version: 0.3)
From【液晶之家】—
10 of 33
Product Specification
AU OPTRONICS CORPORATION
D.Optical Specification
All optical specification is measured under typical condition (Note 1, 2)
Item Symbol Condition Min. Typ. Max. Unit Remark
Response Time
Rise + Fall
Contrast ratio CR
Top
Bottom
Viewing Angle
Left
Right
Transmittance YL θ=0° 6.4 6.8 -- % Note 6
Note 1: Ambient temperature =25℃. To be measured in the dark room.
Note 2: To be measured on the center area of panel with a viewing cone of 1° by Topcon luminance
meter BM-5A, after 15 minutes operation.
TRT θ
At optimized
viewing angle
CR 10≧
=0° -- 16 25 ms Note 3
300 400 -- Note 4, 7
10
30
40
40
15
35
45
45
--
--
--
--
deg.
Note 5,7
www.jxlcd.com
www.jxlcd.com
FIELD=1°
CENTER OF THE SCREEN
BM-5A
A101SW01 V0 (Document Version: 0.3)
From【液晶之家】—
11 of 33
Product Specification
AU OPTRONICS CORPORATION
Note 3: Definition of response time:
The output signals of photo detector are measured when the input signals are changed from
“black” to “white”(falling time) and from “white” to “black”(rising time), respectively.
The response time is defined as the time interval between the 10% and 90% of amplitudes.
Refer to figure as below.
"Black"
100%
S
i
90%
g
n
a
l
(
R
e
l
a
t
i
v
e
v
a
l
1
0%
u
e
)
0%
Note 4.Definition of contrast ratio:
Contrast ratio is calculated with the following formula.
(CR) ratio Contrast=
Note 5. Definition of viewing angle, θ, Refer to figure as below.
www.jxlcd.com
www.jxlcd.com
Tr
Tf
status White"" at is LCD whenoutput detector Photo
status Black"" at is LCD whenoutput detector Photo
"White""White"
Note 6. Measured at the center area of the panel when all the input terminals of LCD panel are
Note 7. The data is from AUO model B101AW06 V1 with same panel of A101SW02 V0.
A101SW01 V0 (Document Version: 0.3)
electrically opened.
【液晶之家】—
12 of 33
Product Specification
AU OPTRONICS CORPORATION
Note 8: Luminance Uniformity of these 9 points is defined as below:
Uniformity =
www.jxlcd.com
www.jxlcd.com
9)-(1 points 9 in luminance minimum
9)-(1 points 9 in luminance maximum
A101SW01 V0 (Document Version: 0.3)
From【液晶之家】—
13 of 33
Product Specification
AU OPTRONICS CORPORATION
E.Reliability Test Items
No. Test items Conditions Remark
1 High Temperature Storage
2 Low Temperature Storage
3 High Ttemperature Operation
4 Low Temperature Operation
5 High Temperature & High Humidity
6 Heat Shock
7 Electrostatic Discharge
8 Image Sticking
9 Vibration (With Carton)
10 Drop (With Carton)
Ta= 60℃
Ta= -20℃
Ta= 50℃
Ta= 0℃
Ta= 50℃. 80% RH
-20℃(0.5h) ~60℃(0.5h), ,50Cycles
Contact = ± 4 kV, class B
Air = ± 8 kV, class B
25℃, 4hrs
Random vibration:
0.015G2/Hz from 5~200Hz
–6dB/Octave from 200~500Hz
Height: 60cm
1 corner, 3 edges, 6 surfaces
240Hrs
240Hrs
240Hrs
40Hrs
2
240Hrs Operation
on-operation
N
Note 5
N
ote 6
IEC 68-34
Note 1: Ta: Ambient Temperature. Tp: Panel Surface Temperature
Note 2: In the standard conditions, there is not display function NG issue occurred. All the cosmetic
Note 3: All the cosmetic specification is judged before the reliability stress.
www.jxlcd.com
www.jxlcd.com
specification is judged before the reliability stress.
A101SW01 V0 (Document Version: 0.3)
From【液晶之家】—
14 of 33
Product Specification
AU OPTRONICS CORPORATION
Note 4: temperature and relative humidity range is shown in the figure below
Note5 : All test techniques follow IEC6100-4-2 standard.
Test Condition Note
Pattern
Contact Discharge:330Ω, 150pF, 1sec, 8 point, 25times/point
www.jxlcd.com
www.jxlcd.com
Procedure
And
Set-up
Criteria
Air Discharge:330Ω, 150pF, 1sec, 8 point, 25times/point
B – Some performance degradation allowed. No data lost.
Self-recoverable hardware failure.
Others
Note 6: Operate with chess board pattern as figure and lasting time and temperature as the conditions.
A101SW01 V0 (Document Version: 0.3)
1. Gun to Panel Distance
2. No SPI command, keep default register settings.
Then judge with 50% gray level, the mura is less than JND 2.5
From【液晶之家】—
15 of 33
Product Specification
AU OPTRONICS CORPORATION
www.jxlcd.com
www.jxlcd.com
A101SW01 V0 (Document Version: 0.3)
From【液晶之家】—
16 of 33
Packing and Marking
1. Packing Form
Product Specification
AU OPTRONICS CORPORATION
www.jxlcd.com
www.jxlcd.com
A101SW01 V0 (Document Version: 0.3)
From【液晶之家】—
17 of 33
Product Specification
AU OPTRONICS CORPORATION
In the carton box, the panel (collectively called as the “Product”) will be with a label of Shipping Number
which represents the identification of the Product at a specific location. The label is composed of a 22-digit
serial number with the following definition:
Example:
501M06ZL06123456781Z05:
Product Manufacturing Week Code: WK50
Product Version: Version 1
2. Panel Label Information
Product Manufactuing Factory: M06
2. Carton Label Information
The packing carton will be attached with a carton label where packing Q’ty, AUO Model Name, AUO Part
N
umber, Customer Part Number (Optional) and a series of Carton Number in 13 or 14 digits are printed. The
Carton Number is apparing in the following format:
Refer to the drawing of packing format for the location and size of the carton label.
www.jxlcd.com
www.jxlcd.com
A101SW01 V0 (Document Version: 0.3)
From【液晶之家】—
18 of 33
Product Specification
AU OPTRONICS CORPORATION
www.jxlcd.com
www.jxlcd.com
A101SW01 V0 (Document Version: 0.3)
From【液晶之家】—
19 of 33
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.