AUO T460HW02 V0 Specification

Global LCD Panel Exchange Center

Product Description: T460HW02 V0 TFT-LCD PANEL

AUO Model Name: T460HW02 V0

Customer Part No. / Project Name:

Customer Signature AU Optronics Corp.

www.panelook.com

Approved by: YuChieh Lin

Reviewed by: Hong-Jye Hong

Prepared by: Falcon Liu

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

Document Version: 1.1

Date: 2007/02/28

Product Functional Specification

46” Full HD Color TFT-LCD Module

Model Name: T460HW02 V0

() Preliminary Specification

(*) Final Specification

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

www.panelook.com

Contents

CONTENTS

RECORD OF REVISIONS

1 GENERAL DESCRIPTION

2 ABSOLUTE MAXIMUM RATINGS

3 ELECTRICAL SPECIFICATION

3-1 ELECTRIACL CHARACTERISTICS

3-2 INTERFACE CONNECTOR

3-3 SIGNAL TIMING SPECIFICATION

3-4 SIGNAL TIMING WAVEFORM

3-5 COLOR INPUT DATA REFERENCE

3-6 POWER SEQUENCE

3-7 BACK LIGHT POWER SPECIFICATION

4 OPTICAL SPECIFICATION

5 MECHANICAL CHARACTERISTICS

6 INTERNATIONAL STANDARD

7 PACKING

8 PRECAUTION

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

Record of Revision

Version Data Page. Old Description New Description Remark

1.0 2007/02/14 First release N/A N/A

www.panelook.com

1.1 2007/02/28 p.9

LVDS Order (NS: Low/Op

p.10

en, JEIDA: High)

LVDS Order (NS: High/Ope

n, JEIDA: Low)

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

1. General Description

This specification applies to the 46 inch Color TFT-LCD Module T460HW02 V0. This LCD module has a

TFT active matrix type liquid crystal panel 1920x1080 pixels, and diagonal size of 46 inch. This module

supports Full HD mode (Non-interlace).

Each pixel is divided into Red, Green and Blue sub-pixels or dots which are arranged in vertical stripes.

Gray scale or the brightness of the sub-pixel color is determined with a 8-bit gray scale signal for each dot.

The T460HW02 V0 has been designed to apply the 8-bit 2 channel LVDS interface method. It is intended to

support displays where high brightness, Hi Color Gamut (92% NTSC), wide viewing angle, and high color

www.panelook.com

depth are very important.

General Information

Items Specification Unit Note

Active Screen Size 46 inches Diagonal

Display Area 1018.08(H) x 572.67(V) mm

Outline Dimension 1083.0(H) x 627.0(V) x 50.6(D) mm With Balance Board

Driver Element a-Si TFT active matrix

Display Colors 16.7M Colors

Color Gamut 92 % NTSC

Number of Pixels 1920 x 1080 Pixel

Pixel Arrangement RGB vertical stripe

Display Mode Normally Black

Surface Treatment AR, 3H

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

2. Absolute Maximum Ratings

The followings are maximum values which, if exceeded, may cause faulty operation or damage to the unit

Item Symbol Min. Max Unit Note

Logic/LCD Drive Voltage VDD -0.3 14.0 VDC 1

Input Voltage of Signal Vin -0.3 3.6 VDC 1

Operating Temperature TOP 0 +50 °C 2

Operating Humidity HOP 10 90 %RH 2

Storage Temperature TST -20 +60 °C 2

Storage Humidity HST 10 90 %RH 2

Shock (non-operation) ±x, ±y -- 40 G 3

Shock (non-operation) ±z -- 30 G 3

www.panelook.com

Vibration (non-operation) -- 1.5 G 4

Note 1: Duration = 50ms

Note 2: Maximum Wet-Bulb should be 39°C and No condensation.

Note 3: Sine wave, 11ms, direction: ±x, ±y, ±z (one time each direction)

Note 4: Wave form: random, vibration level: 1.5G RMS, Bandwidth: 10--300Hz

Duration: X, Y, Z 30min (one time each direction)

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

3. Electrical Specification

The T460HW02 requires two power inputs. One is employed to power the LCD electronics and to drive the

TFT array and liquid crystal. The second input, which powers the CCFL, is typically generated by an

integrate power (I/P) system.

3.1 Electrical Characteristics

www.panelook.com

Parameter Symbol

Unit Note

Min. Typ. Max

Power Supply Input Voltage VDD 10.8 12 13.2 VDC

Power Supply Input Current IDD -- 1.08 1.2 A 1

Power Consumption PC -- 13 15.84 Watt 1

Value

Inrush Current I

-- -- 4.5 A 5

RUSH

Differential Input

High Threshold

-- -- +100 mVDC 4

Voltage

LVDS

Interface

Differential Input

Low Threshold

-100 -- -- mVDC 4

Voltage

Common Input

1.10 1.25 1.40 VDC

CIM

VIH

(High)

2.4 -- 3.3 V

CMOS

Voltage

Input High

Threshold Voltage

Interface

Input Low

Threshold Voltage

(Low)

0 -- 0.7 V

Backlight Power Consumption PBL -- 210 -- Watt 2

Life Time 30000 -- -- Hours 3

The performance of the Lamp in LCD panel, for example life time or brightness, is extremely influenced

by the characteristics of the balance board and I/P board. All the parameters should be carefully

designed as not to produce too much leakage current from high-voltage output. While design or order

balance board, please make sure unwanted lighting caused by the mismatch of the lamp and balance

board (no lighting, flicker, etc) never occurs. After confirmation, the LCD Panel should be operated in

the same condition as installed in your instrument.

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

Do not attach a conducting tape to lamp connecting wire. If the lamp wire attach to conducting tape,

TFT-LCD Module has a low luminance and the inverter has abnormal action, because leakage current

occurs between lamp wire and conducting tape.

The relative humidity must not exceed 80% non-condensing at temperatures of 40°C or less. At

temperatures greater than 40°C the wet bulb temperature must not exceed 39°C. When operate at low

temperatures, the brightness of CCFL will drop and the lifetime of CCFL will be reduced.

Note:

www.panelook.com

1. V

2. The backlight power consumption shown above is tested by lamp current I

=12.0V, fV=60Hz, fCLK=81.5Mhz, 25°C, VDD duration time=400µs, test pattern: white pattern

=6.0mA.

3. The life is determined as the time at which luminance of the lamp is 50% compared to that of initial

value at the typical lamp current on condition of continuous operating at 25±2°C.

4. V

=1.25V

CIM

VTH

VCIM

VTL

Figure: LVDS Differential Voltage

5. Measurement condition: rising time=400 µs

0.9 Vdd

Vdd

GND

0.1 Vdd

400

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Global LCD Panel Exchange Center

3.2 Interface Connections

 LCD connector: FI-RE51S-HF (JAE) or equivalent

 Mating connector: FI-RE51S-HL (JAE) or equivalent

PIN # Signal Name Description

1 VDD 12V power supply

2 VDD 12V power supply

3 VDD 12V power supply

4 VDD 12V power supply

5 VDD 12V power supply

6 GND Ground

www.panelook.com

7 GND Ground

8 GND Ground

9 GND Ground

10 RO_0- Negative(-) LVDS differential data input

11 RO_0+ Positive(+) LVDS differential data input

12 RO_1- Negative(-) LVDS differential data input

13 RO_1+ Positive(+) LVDS differential data input

14 RO_2- Negative(-) LVDS differential data input

15 RO_2+ Positive(+) LVDS differential data input

16 GND Ground

17 RO_CLK- Clock Signal(-)

18 RO_CLK+ Clock Signal(+)

19 GND Ground

20 RO_3- Negative(-) LVDS differential data input

21 RO_3+ Positive(+) LVDS differential data input

22 NC No connection

23 NC No connection

24 GND Ground

25 RE_0- Negative(-) LVDS differential data input

26 RE_0+ Positive(+) LVDS differential data input

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

+ 19 hidden pages

AUO T460HW02 V0 Specification

Specifications and Main Features

Frequently Asked Questions

User Manual