AUO T370HW05 V2 Specification

T370HW05 V2 Product Specification

Rev. 00

Model Name: T370HW05 V2

Issue Date: 2011/02/22

( )Preliminary Specifications

(＊＊＊＊)Final Specifications

Customer Signature Date AUO Date

Approved By

_________________________________

Note

Approval By PM Director YenTing Chiu ____________________________________

Reviewed By RD Director Eugene CC Chen ____________________________________ Reviewed By Project Leader Ebola Lee ____________________________________

Prepared By PM Eric Lin ____________________________________

T370HW05 V2 Product Specification

Rev. 00

Contents

No

CONTENTS

RECORD OF REVISIONS 1 GENERAL DESCRIPTION 2 ABSOLUTE MAXIMUM RATINGS 3 ELECTRICAL SPECIFICATION

3-1 ELECTRIACL CHARACTERISTICS

3-2 INTERFACE CONNECTIONS

3-3 SIGNAL TIMING SPECIFICATION

3-4 SIGNAL TIMING WAVEFORM

3-5 COLOR INPUT DATA REFERENCE

3-6 POWER SEQUENCE

3-7 BACKLIGHT SPECIFICATION 4 OPTICAL SPECIFICATION 5 MECHANICAL CHARACTERISTICS 6 RELIABILITY TEST ITEMS 7 INTERNATIONAL STANDARD

7-1 SAFETY

7-2 EMC 8 PACKING

8-1 DEFINITION OF LABEL

8-2 PACKING METHODS

8-3 PALLET AND SHIPMENT INFORMATION 9 PRECAUTION

9-1 MOUNTING PRECAUTIONS

9-2 OPERATING PRECAUTIONS

9-3 ELECTROSTATIC DISCHARGE CONTROL

9-4 PRECAUTIONS FOR STRONG LIGHT EXPOSURE

9-5 STORAGE

9-6 HANDLING PRECAUTIONS FOR PROTECT FILM

Record of Revision

T370HW05 V2 Product Specification

Rev. 00

Version

0.0 2011/01 First Release

Date Page Description

T370HW05 V2 Product Specification

Rev. 00

1. General Description

This specification applies to the 37.0 inch Color TFT-LCD Module T370HW05 V2. This LCD module has a TFT active matrix type liquid crystal panel 1,920x1,080 pixels, and diagonal size of 37.0 inch. This module supports 1,920 x1,080 mode. Each pixel is divided into Red, Green and Blue sub-pixels or dots which are arranged in vertical stripes. Gray scale or the brightness of the sub-pixel color is determined with a 10-bit gray scale signal for each dot.

The T370HW05 V2 has been designed to apply the 10-bit 4 channel LVDS interface method. It is intended to support displays where high brightness, wide viewing angle, high color saturation, and high color depth are very important.

* General Information

Items Specification Unit Note

Active Screen Size 37.00 inch Display Area 819.36(H) x 460.89(V) mm Outline Dimension 856.4(H) x 501 (V) x 10.8 (D) mm Driver Element a-Si TFT active matrix Display Colors 826.4(H) x 468 Colors Number of Pixels 8 bits, 16.7M Pixel Pixel Pitch 1,920x1080 mm Pixel Arrangement 0.4268 (H) x 0.4268 (W) Display Operation Mode RGB vertical stripe Surface Treatment Normally Black Haze=2%

T370HW05 V2 Product Specification

2. Absolute Maximum Ratings

The followings are maximum values which, if exceeded, may cause faulty operation or damage to the unit

Item Symbol Min Max Unit Conditions

Logic/LCD Drive Voltage Vcc -0.3 14 [Volt] Note 1 Input Voltage of Signal Vin -0.3 4 [Volt] Note 1 Operating Temperature TOP 0 +50 [oC] Note 2 Operating Humidity HOP 10 90 [%RH] Note 2 Storage Temperature TST -20 +60 [oC] Note 2 Storage Humidity HST 10 90 [%RH] Note 2 Panel Surface Temperature PST 65 [oC] Note 3

Note 1: Duration: 50 msec. Note 2: Maximum Wet-Bulb should be 39 and No condensation.℃

Rev. 00

The relative humidity must not exceed 90% non-condensing at 40 or less. At temperature greater than 40 , the ℃ ℃ wet bulb temperature must not exceed 39 .℃ Note 3: Surface temperature is measured at 50℃ Dry condition

T370HW05 V2 Product Specification

Rev. 00

3. Electrical Specification

The T370HW05 V2 requires two power inputs. One is employed to power the LCD electronics and to drive the TFT array and liquid crystal. The second is employed for LED lightbar.

3.1 Electrical Characteristics

Parameter Symbol

Unit Note

Min. Typ. Max LCD Power Supply Input Voltage VDD 10.8 12 13.2 VDC 1 Power Supply Input Current IDD - 0.41 1.02 A 2 Power Consumption PC 4.92 12.24 Watt 2

Value

Inrush Current I

4 A 3

RUSH

Differential Input High Threshold

VTH +100 -- +300 mVDC 4

Voltage

LVDS Interface

CMOS Interface

Differential Input Low Threshold Voltage

Input Common Mode Voltage V

Input High Threshold Voltage

(HIGH)

Input Low Threshold Voltage

VTL -300 -- -100 mVDC 4

ICM

1.1 1.25 1.4 VDC 4

V

IH

2.7 -- 3.3 VDC

V

IL

0 -- 0.6 VDC

(LOW)

Backlight Power Consumption PBL 57.6 61 Watt Life Time (MTTF) 30000

-- Hours 8

Note:

1. The ripple voltage should be controlled under 10% of VCC

2. Test Condition:

(1) V

= 12.0V

DD

(2) Fv = 60Hz (3) F

= 80.74MHZ

CLK

(4) Temperature = 25 ℃ (5) Test Pattern : White Pattern

3. Measurement condition : Rising time = 400us

s

µ

T370HW05 V2 Product Specification

Rev. 00

V

90%

DD

10%

4. V

= 1.25V

ICM

GND

V

0V

ICM

5. Input Channel Pair Skew Margin

400

V

TH

V

TL

6. The relative humidity must not exceed 80% non-condensing at temperature of 40℃ or less. At temperature greater than 40 , the wet bulb temperature must not exceed 39℃ ℃. When operating at high temperature, the brightness of LED will drop and the life time of LED will be reduced.

7. The lifetime (MTTF) is defined as the time where luminance of LED is 50% compared to its original value. [Operating condition: Continuous operating at Ta = 25±2℃]

.

3.2 Interface Connections

T370HW05 V2 Product Specification

Rev. 00

LCD connector: 187059-51221 (P-TWO, LVDS connector)



Mating connector: 41Pin: 187087-41193 51Pin: 187087-51193

PIN Symbol Description PIN

1 2 3 4 5 6 7 8 9

10

N.C. No connection 21 N.C. AUO Internal Use Only

N.C. No connection 23 N.C. No connection 24 N.C. No connection 25 N.C. No connection 26 N.C. AUO Internal Use Only 27 N.C. No connection 28

GND Ground 29

CH3_0-

187060-41221 (P-TWO, LVDS connector)

22

LVDS Channel 3, Signal 0- 30

Symbol Description

CH3_3+

CH3_4-

CH3_4+

GND GND

CH4_0-

CH4_0+

CH4_1-

CH4_1+

CH4_2-

LVDS Channel 3, Signal 3+

LVDS Channel 3, Signal 4-

LVDS Channel 3, Signal 4+

LVDS Channel 4, Signal 0-

LVDS Channel 4, Signal 0+

LVDS Channel 4, Signal 1-

LVDS Channel 4, Signal 1+

LVDS Channel 4, Signal 2-

Ground Ground

11 12 13 14 15 16 17 18 19 20

CH3_0+

CH3_1-

CH3_1+

CH3_2-

CH3_2+

GND

CH3_CLK-

CH3_CLK+

GND

CH3_3-

LVDS Channel 3, Signal 0+ 31

LVDS Channel 3, Signal 1- 32

LVDS Channel 3, Signal 1+ 33

LVDS Channel 3, Signal 2- 34

LVDS Channel 3, Signal 2+ 35

Ground 36

LVDS Channel 3, Clock - 37

LVDS Channel 3, Clock + 38

Ground 39

LVDS Channel 3, Signal 3- 40

41

CH4_2+

GND

CH4_CLK-

CH4_CLK+

GND

CH4_3-

CH4_3+

CH4_4-

CH4_4+

GND Ground GND Ground

LVDS Channel 4, Signal 2+

LVDS Channel 4, Clock -

LVDS Channel 4, Clock +

LVDS Channel 4, Signal 3-

LVDS Channel 4, Signal 3+

LVDS Channel 4, Signal 4-

LVDS Channel 4, Signal 4+

Ground

Note: N.C. : please leave this pin unoccupied. It can not be connected by any signal (Low/GND/High).

1 2 3 4

5

6

7 LVDS_SEL 8

9 10 11 12 13 14 15 16 17 18 19 CH1_CLK- LVDS Channel 1, Clock - 44 20 CH1_CLK+ LVDS Channel 1, Clock + 45 21 22 23 24 25

Symbol Description PIN

N.C. N.C. N.C. N.C.

BITSEL

ROTATE

N.C. N.C. N.C.

GND Ground 36 CH2_CLK+ LVDS Channel 2, Clock +

CH1_0- LVDS Channel 1, Signal 0- 37

CH1_0+ LVDS Channel 1, Signal 0+ 38

CH1_1- LVDS Channel 1, Signal 1- 39

CH1_1+ LVDS Channel 1, Signal 1+ 40

CH1_2- LVDS Channel 1, Signal 2- 41

CH1_2+ LVDS Channel 1, Signal 2+ 42

GND Ground 43

GND Ground 46

CH1_3- LVDS Channel 1, Signal 3- 47

CH1_3+ LVDS Channel 1, Signal 3+ 48

CH1_4- LVDS Channel 1, Signal 4- 49

CH1_4+ LVDS Channel 1, Signal 4+ 50

AUO Internal Use Only 26 AUO Internal Use Only 27 AUO Internal Use Only 28 AUO Internal Use Only 29

LVDS 8/10bit Input Selection

Open/High(3.3V) : 10bits

Low(GND) : 8bits

Panel Rotation Display Control

High(3.3V) : Rotate Enable

Open/Low(GND) : Rotate Disable

Open/High(3.3V) for NS,

Low(GND) for JEIDA AUO Internal Use Only 33 AUO Internal Use Only 34 AUO Internal Use Only 35 CH2_CLK- LVDS Channel 2, Clock -

51

30

31

32

T370HW05 V2 Product Specification

Rev. 00

Symbol Description

N.C. N.C.

CH2_0- LVDS Channel 2, Signal 0-

CH2_0+ LVDS Channel 2, Signal 0+

CH2_1- LVDS Channel 2, Signal 1-

CH2_1+ LVDS Channel 2, Signal 1+

CH2_2- LVDS Channel 2, Signal 2-

CH2_2+ LVDS Channel 2, Signal 2+

GND Ground

CH2_3- LVDS Channel 2, Signal 3-

CH2_3+ LVDS Channel 2, Signal 3+

CH2_4- LVDS Channel 2, Signal 4-

CH2_4+ LVDS Channel 2, Signal 4+

N.C.

N.C. GND Ground GND Ground GND Ground

N.C. No connection

V

DD

V

DD

V

DD

V

DD

AUO Internal Use Only AUO Internal Use Only

Power Supply, +12V DC Regulated Power Supply, +12V DC Regulated Power Supply, +12V DC Regulated Power Supply, +12V DC Regulated

Note: N.C. : please leave this pin unoccupied. It can not be connected by any signal (Low/GND/High).

 LVDS Option = High/OpenNS

P r e v io u s C ycle C urre n t C yc le N e xt C ycle

C lo c k

T370HW05 V2 Product Specification

Rev. 00

C H x_ 0 + C H x_ 0 -

C H x_ 1 + C H x_ 1 -

C H x_ 2 + C H x_ 2 -

C H x_ 3 + C H x_ 3 -

C H x_ 4 + C H x_ 4 -

Note: x = 1, 2, 3, 4…

 LVDS Option = LowJEIDA

P re v io us C ycle C u rre n t C ycle N e x t C ycle

R 0R 5 G 0G 0R 0R 1 R 2R 3R 4 R 1

G 1B 0 B 1B 1G 1G 2 G 3G 4G 5 G 2

B 2N A D ED EB 2B 3 B 4B 5N A B3

R 6B 7 N AN AR 6R 7 G 6G 7B 6 R 7

R 8B 9 N AN AR 8R 9 G 8G 9B 8 R 9

C lo c k

C H x_ 0 + C H x_ 0 -

C H x_ 1 + C H x_ 1 -

C H x_ 2 + C H x_ 2 -

C H x_ 3 + C H x_ 3 -

C H x_ 4 + C H x_ 4 -

R 4R 9 G 4G 4R 4R 5 R 6R 7R 8 R 5

G 5B 4 B 5B 5G 5G 6 G 7G 8G 9 G 6

B 6N A D ED EB 6B 7 B8B 9N A B 7

R 2B 3 N AN AR 2R 3 G 2G 3B 2 R 3

R 0B 1 N AN AR 0R 1 G 0G 1B 0 R 1

Note: x = 1, 2, 3, 4…

T370HW05 V2 Product Specification

Rev. 00

3.3 Signal Timing Specification

This is the signal timing required at the input of the user connector. All of the interface signal timing should be satisfied with the following specifications for its proper operation.

Timing Table

Signal Item Symbol Min. Typ. Max Unit

Period Tv 1090 1130 1392 Th

Vertical Section

Active Tdisp (v) 1080 Th

Blanking Tblk (v) 10 50 312 Th

Period Th 540 570 580 Tclk

Horizontal Section

Active Tdisp (h) 480 Tclk

Blanking Tblk (h) 60 90 100 Tclk Clock Frequency Fclk=1/Tclk 64.8 77.29 80.74 MHz Vertical Frequency Frequency Fv 94 120 122 Hz Horizontal Frequency

Notes: (1) Display position is specific by the rise of DE signal only.

Horizontal display position is specified by the rising edge of 1st DCLK after the rise of 1st DE, is displayed on the left edge of the screen.

(2)Vertical display position is specified by the rise of DE after a “Low” level period equivalent to eight times of

Frequency Fh 120 135.6 139.2 KHz

horizontal period. The 1st data corresponding to one horizontal line after the rise of 1st DE is displayed at the top

line of screen. (3)If a period of DE “High” is less than 1366 lines, the rest of the screen displays black. (4)The display position does not fit to the screen if a period of DE “High” and the effective data period do not

synchronize with each other.

Rev. 00

Tv

Tdisp(v)Tblk(v)

M pixel

Th

N Lin e

DE

RGB Data

Line

N

Invalid Data Invalid Data

Line

1

Line

2

Line

3

Line

4

Line

N

T370HW05 V2 Product Specification

CLK

Th

Tdisp(h) Tblk(h)

Pixel

13

Pixel

14

17

Pixel

18

Pixel

21

Pixel

22

Pixel

M-11

Pixel

M-10

Pixel

M-7

Pixel

M-6

Pixel

M-3

Pixel

M-2

Invalid Data

Pixel

1

Pixel

2

Pixel

5

Pixel

6

DE

CH1

CH2

Pixel

M-15

Pixel

M-14

Pixel

M-11

Pixel

M-10

Pixel

M-7

Pixel

M-6

Tclk

Pixel

M-3

Pixel

M-2

Invalid Data

Pixel

1

Pixel

2

Pixel 5Pixel

9

Pixel 6Pixel

10

Pixel

CH3

CH4

3.4 Signal Timing Waveforms

M-13

Pixel

M-12

M-9

Pixel

M-8

M-5

Pixel

M-4

Pixel

M-1

Pixel

M

Invalid Data

Pixel

3

Pixel

4

Pixel 7Pixel

11

Pixel 8Pixel

12

Pixel

15

Pixel

16

Pixel

19

Pixel

20

Pixel

23

Pixel

24

Pixel

M-9

Pixel

M-8

Pixel

M-5

Pixel

M-4

Pixel

M-1

Pixel

M

Invalid Data

Pixel

3

Pixel

4

Pixel

7

Pixel

8

T370HW05 V2 Product Specification

Rev. 00

3.5 Color Input Data Reference

The brightness of each primary color (red, green and blue) is based on the 10-bit gray scale data input for the color; the higher the binary input, the brighter the color. The table below provides a reference for color versus data input.

COLOR DATA REFERENCE

Input Color Data

Color

Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Red(1023) 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Green(1023) 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0

Basic

Blue(1023) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1

Color

Cyan 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Magenta 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 Yellow 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 RED(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 RED(001) 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

R

---- RED(1022) 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 RED(1023) 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

MSB LSB

R9 R8 R7 R6 R5 R4 R3 R2 R1 R0 G9 G8 G7 G6 G5 G4 G3 G2 G1 G0 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0

RED

MSB LSB

GREEN

BLUE

MSB LSB

GREEN(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 GREEN(001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0

G

---- GREEN(1022) 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 GREEN(1023) 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 BLUE(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 BLUE(001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1

B

---- BLUE(1022) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 0 BLUE(1023) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1

3.6 Power Sequence for LCD

T370HW05 V2 Product Specification

Rev. 00

Power Supply For LC D VDD (+12V)

Interface Signal (LV DS Da ta & CLK)

Backligh t on/off control signal (VB LO N)

CM O S Interface Signal

Parameter

G ND

10 %

90 %

t1

t2

Va lid D ata

t3 t4

t8 t9

Values

Min. Type. Max.

9 0%

10 %

t6

t5

10 %

t7

Unit

t1 0.4 --- 30 ms t2 0.1 --- 150 ms t3 450 --- --- ms t4 0*1 --- --- ms t5 0 --- --- ms t6 --- --- ---*2 ms t7 500 --- --- ms

t8 10 --- 50 ms t9 0 --- --- ms

Note: (1) t4=0 : concern for residual pattern before BLU turn off. (2) t6 : voltage of VDD must decay smoothly after power-off. (customer system decide this value)

3.7.1 Electrical specification

Item Symbol Condition

T370HW05 V2 Product Specification

Rev. 00

Spec

Unit Note

Min Typ Max

1 2 3 4

5 On/Off control voltage

6

Input Voltage VDDB - 22.8 Input Current I

Input Power P

Inrush Current I

V

BLON

On/Off control current

7 Dimming Control Voltage V_DIM

8 Dimming Control Current 9 Internal Dimming Ratio

10

External PWM

Control Voltage

V_EPWM

VDDB=24V

DDB

VDDB=24V

DDB

VDDB=24V

RUSH

ON 2 - 5.5 -

VDDB=24V

OFF

I

VDDB=24V

BLON

MAX 3.0 - 5.5 VDC -

VDDB=24V

MIN

I_DIM VDDB=24V

DIM_R VDDB=24V

MAX VDDB=24V

MIN VDDB=24V

24 25.2

2.4 2.54

57.6

61 W 1

VDC ADC 1

5 ADC 2

VDC

0 - 0.8

- - 1.5 mA -

- 0 - VDC -

- - 2 mADC 5 - 100 % 3 2 - 5.5 -

VDC

0 - 0.8

-

11 12 External PWM Duty ratio 13

External PWM

Control Current

External PWM

Frequency

I_EPWM VDDB=24V

D_EPWM VDDB=24V

- - 2 mADC -

5 - 100 % 3

F_EPWM VDDB=24V 140 180 240 Hz -

HI Open Collector VDC 4

14

15

DET status signal DET

Lo

VDDB=24V

0 - 0.8 VDC 4

Input Impedance Rin VDDB=24V 300 Kohm -

Note 1 : Dimming ratio= 100% (MAX)（Ta=25±5 , Turn on for 45minutes℃ ） Note 2: Measurement condition Rising time = 20ms (VDDB : 10%~90%);

Note 3: Less than 5% dimming control is functional well and no backlight shutdown happened Note 4: Normal : 0~0.8V ; Abnormal : Open collector

3.7.2 Input Pin Assignment

LED driver board connector : Cvilux CI0114M1HR0-NH

Pin Symbol Description

1 VDDB Operating Voltage Supply, +24V DC regulated 2 VDDB Operating Voltage Supply, +24V DC regulated 3 VDDB Operating Voltage Supply, +24V DC regulated 4 VDDB Operating Voltage Supply, +24V DC regulated 5 VDDB Operating Voltage Supply, +24V DC regulated 6 BLGND Ground and Current Return 7 BLGND Ground and Current Return 8 BLGND Ground and Current Return

T370HW05 V2 Product Specification

Rev. 00

9 BLGND Ground and Current Return

10 BLGND Ground and Current Return

BLU status detection:

11 DET

12 VBLON

13 VDIM(**)

14 PDIM(*)

Normal : 0~0.8V ; Abnormal : Open collector (Recommend Pull high R > 10K, VDD = 3.3V)

BLU On-Off control: High/Open (2~5.5V) : BL On ; Low (0~0.8V/GND) : BL Off

Internal PWM (0~3.3V for 5~100% Duty, open for 100%) < NC ; at External PWM mode>

External PWM (5%~100% Duty, open for 100%) < NC ; at Internal PWM mode>

(Note*) IF External PWM function includes 5% dimming ratio. Judge condition as below: (1) Backlight module must be lighted ON normally. (2) All protection function must work normally. (3) Uniformity and flicker could NOT be guaranteed

T370HW05 V2 Product Specification

3.7.3 Power Sequence for LED Driver

Rev. 00

Dip condition for LED Driver

Power Input for BLU

(VDDB)

VDDB(typ.)*0.8

Parameter

T1 20 - - ms T2 500 - - ms T3 250 - - ms

T6

Value

Min Typ Max

Units

T4 0 - - ms T5 1 - - ms

T6 - - 10 ms Note: (1) When CMOS Interface is N.C. (no connection), opened in Transmitted end, T8 timing spec can be negligible

T370HW05 V2 Product Specification

Rev. 00

4. Optical Specification

Optical characteristics are determined after the unit has been ‘ON’ and stable for approximately 45 minutes in a dark environment at 25°C. The values specified are at an approximate distance 50cm from the LCD surface at a viewing angle of φ and θ equal to 0°.

Fig.1 presents additional information concerning the measurement equipment and method.

SR3 or equivalent

Parameter Symbol

Min. Typ. Max Contrast Ratio CR 3600 4000 -- 1 Surface Luminance (White) LWH 320 400 -- cd/m2 2

Luminance Variation δ Response Time (G to G) Tγ -- 6.5 -- Ms 4 Color Gamut NTSC 72 % Color Coordinates

Red RX 0.63 RY 0.330 Green GX 0.32 GY 0.620 Blue BX 0.150 BY 0.04

WHITE(9P)

-- -- 1.33 3

Typ.-0.03

Values

Unit Notes

Typ.+0.03

White WX 0.280 WY

Viewing Angle 5

x axis, right(φ=0°) θr -- 89 -- degree x axis, left(φ=180°) θl -- 89 -- degree y axis, up(φ=90°) θu -- 89 -- degree y axis, down (φ=270°) θ

-- 89 -- degree

d

0.290

2 3

7

T370HW05 V2 Product Specification

Rev. 00

Note:

1. Contrast Ratio (CR) is defined mathematically as:

Surface Luminance of

Contrast Ratio=

Surface Luminance of

2. Surface luminance is luminance value at point 5 across the LCD surface 50cm from the surface with all pixels

L

on5

L

off5

displaying white. From more information see FIG 2. At driver current I

= 2.4A, LWH=L

DDB

where L

on5

is the

on5

luminance with all pixels displaying white at center 5 location.

3. The variation in surface luminance, δWHITE is defined (center of Screen) as:

δ

WHITE(9P)

= Maximum(L

on1

, L

on2

,…,L

)/ Minimum(L

on9

on1

, L

on2

,…L

on9

)

4. Response time Tγ is the average time required for display transition by switching the input signal for five luminance ratio (0%,25%,50%,75%,100% brightness matrix) and is based on Fv=120Hz to optimize.

Target Measured

Response Time

0%

25%

Start

50% 75%

100%

5. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are determined for the horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the LCD surface. For more information see FIG4.

0% 25% 50% 75% 100%

0% to 25% 0% to 50% 0% to 75% 0% to 100% 25% to 0% 25% to 50% 25% to 75% 25% to 100% 50% to 0% 50% to 25% 75% to 0% 75% to 25% 75% to 50%

100% to 0% 100% to 25% 100% to 50% 100% to 75%

50% to 75% 50% to 100%

75% to 100%

FIG. 2 Luminance

H/2

H/6

V

1

H

V/2 V/6

T370HW05 V2 Product Specification

Rev. 00

FIG.3 Response Time

The response time is defined as the following figure and shall be measured by switching the input signal for “any level of grey(bright) “ and “any level of gray(dark)”.

Any level of gray (Bright) Any level of gray (Dark) Any level of gray (Bright)

FIG.4 Viewing Angle

T370HW05 V2 Product Specification

Rev. 00

5. Mechanical Characteristics

The contents provide general mechanical characteristics for the model T370HW05 V2. In addition the figures in the next page are detailed mechanical drawing of the LCD.

Horizontal 856.4 mm

Outline Dimension

Bezel Opening

Active Display Area

Surface Treatment Anti-Glare, 3H

Weight 7500 g (Typ.)

Vertical 501.0 mm

Depth 10.8mm

Horizontal 826.4 mm

Vertical 468.0 mm

Horizontal 819.36mm

Vertical 460.89mm

Front View

T370HW05 V2 Product Specification

Rev. 00

Back View

T370HW05 V2 Product Specification

Rev. 00

6. Reliability Test Items

T370HW05 V2 Product Specification

Rev. 00

1 High temperature storage test 3 60℃, 300hrs 2 Low temperature storage test 3 -20℃, 300hrs 3 High temperature operation test 3 50℃, 300hrs 4 Low temperature operation test 3 -5℃, 300hrs

5 Vibration test (non-operation) 3

6 Shock test (non-operation) 3

7 Vibration test (With carton) 5

Test Item Q’ty Condition

Wave form: random Vibration level: 1.0G RMS Bandwidth: 10-300Hz, Duration: X, Y, Z 10min One time each direction Shock level: 50G Waveform: half since wave, 11ms Direction: ±X, ±Y, ±Z, One time each direction

Random wave (1.05Grms, 10-200Hz) 10mins/ Per each X,Y,Z axes

8 Drop test (With carton) 5

Height: 30.5cm (ASTMD4169-1) 1 corner, 3 edges, 6 flats(ASTM D5276)

7. International Standard

7.1 Safety

(1) UL 60950-1, UL 60065; Standard for Safety of Information Technology Equipment Including

electrical Business Equipment.

(2) IEC 60950-1 : 2001, IEC 60065:2001 ; Standard for Safety of International Electrotechnical

Commission

(3) EN 60950: 2001+A11, EN 60065:2002+A1:2006; European Committee for Electrotechnical

Standardization (CENELEC), EUROPEAN STANDARD for Safety of Information Technology Equipment Including Electrical Business Equipment.

7.2 EMC

(1) ANSI C63.4 “Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and

Electrical Equipment in the Range of 9kHz to 40GHz. “American National standards Institute(ANSI),

T370HW05 V2 Product Specification

Rev. 00

1992

(2) C.I.S.P.R “Limits and Methods of Measurement of Radio Interface Characteristics of Information

Technology Equipment.” International Special committee on Radio Interference.

(3) EN 55022 “Limits and Methods of Measurement of Radio Interface Characteristics of Information

Technology Equipment.” European Committee for Electrotechnical Standardization. (CENELEC), 1998

QTY :

5

Manufactured

XX/XX

MADE

IN

XXXXX

8. Packing

8-1 DEFINITION OF LABEL:

A. Panel Label:

*xxxxxxxxxxxx-xxxx*

T370HW05 V2 Product Specification

Rev. 00

Panel Unique ID

AUO Internal Use

XXXXX Model NO: T370HW05 V.2 XXXXXXX

Week Factory Location AUO Internal Use

AUO Internal Use Year

Green mark description

AU Optronics

(1) For Pb Free Product, AUO will add for identification. (2) For RoHs compatible products, AUO will add RoHS for identification.

Note: The green Mark will be present only when the green documents have been ready by AUO internal green team. (definition of green design follows the AUO green design checklist.)

B. Carton Label:

T370HW05 V2

97.37T07.200

8-2 PACKING METHODS:

Protect Film

Creped Paper Tape

T370HW05 V2 Product Specification

Rev. 00

Anti-Static Bag (Blue)

Cushion Set

( 5 ) Pcs Modules

"H" Tape

( 5 ) Pcs / 1 Carton

8-3 Pallet and Shipment Information

T370HW05 V2 Product Specification

Rev. 00

Item

Specification

Qty. Dimension Weight (kg) 1 Packing BOX 5pcs/box 900(L)*280(W)*610(H) 43 2 Pallet 1 1150(L)*910(W)*132(H) 14 3 Boxes per Pallet 8 boxes/pallet 4 Panels per Pallet 40 pcs/pallet

PET Strap

Angle Protector

Label

Stretch Film

Wooden Pallet

Packing

Remark

T370HW05 V2 Product Specification

8. PRECAUTIONS

Please pay attention to the followings when you use this TFT LCD module.

9-1 MOUNTING PRECAUTIONS

(1) You must mount a module using holes arranged in four corners or four sides. (2) You should consider the mounting structure so that uneven force (ex. twisted stress) is not applied

to module. And the case on which a module is mounted should have sufficient strength so that external force is not transmitted directly to the module.

(3) Please attach the surface transparent protective plate to the surface in order to protect the polarizer.

Transparent protective plate should have sufficient strength in order to the resist external force.

(4) You should adopt radiation structure to satisfy the temperature specification. (5) Acetic acid type and chlorine type materials for the cover case are not desirable because the former

Rev. 00

generates corrosive gas of attacking the polarizer at high temperature and the latter cause circuit broken by electro-chemical reaction.

(6) Do not touch, push or rub the exposed polarizer with glass, tweezers or anything harder than HB

pencil lead. And please do not rub with dust clothes with chemical treatment. Do not touch the surface of polarizer for bare hand or greasy cloth. (Some cosmetics are detrimental to the polarizer.)

(7) When the surface becomes dusty, please wipe gently with absorbent cotton or other soft materials

like chamois soaks with petroleum benzene. Normal-hexane is recommended for cleaning the adhesives used to attach front/ rear polarizer. Do not use acetone, toluene and alcohol because they cause chemical damage to the polarizer.

(8) Wipe off saliva or water drops as soon as possible. Their long time contact with polarizer causes

deformations and color fading.

(9) Do not open the case because inside circuits do not have sufficient strength.

9-2 OPERATING PRECAUTIONS

(1) The device listed in the product specification sheets was designed and manufactured for TV

application

(2) The spike noise causes the mis-operation of circuits. It should be lower than following voltage:

V=±200mV(Over and under shoot voltage) (3) Response time depends on the temperature. (In lower temperature, it becomes longer..) (4) Brightness of CCFL depends on the temperature. (In lower temperature, it becomes lower.) And in

lower temperature, response time (required time that brightness is stable after turned on) becomes

longer. (5) Be careful for condensation at sudden temperature change. Condensation makes damage to

polarizer or electrical contacted parts. And after fading condensation, smear or spot will occur. (6) When fixed patterns are displayed for a long time, remnant image is likely to occur. (7) Module has high frequency circuits. Sufficient suppression to the electromagnetic interference shall

be done by system manufacturers. Grounding and shielding methods may be important to minimize

the interface.

9-3 ELECTROSTATIC DISCHARGE CONTROL

Since a module is composed of electronic circuits, it is not strong to electrostatic discharge. Make certain that treatment persons are connected to ground through wristband etc. And don’t touch interface pin directly.

9-4 PRECAUTIONS FOR STRONG LIGHT EXPOSURE

Strong light exposure causes degradation of polarizer and color filter.

9-5 STORAGE

When storing modules as spares for a long time, the following precautions are necessary.

(1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the

T370HW05 V2 Product Specification

Rev. 00

temperature between 5 and 35 at normal humidity.℃ ℃ (2) The polarizer surface should not come in contact with any other object. It is recommended that they

be stored in the container in which they were shipped.

9-6 HANDLING PRECAUTIONS FOR PROTECTION FILM

(1) The protection film is attached to the bezel with a small masking tape. When the protection film is

peeled off, static electricity is generated between the film and polarizer. This should be peeled off

slowly and carefully by people who are electrically grounded and with well ion-blown equipment or

in such a condition, etc. (2) When the module with protection film attached is stored for a long time, sometimes there remains a

very small amount of glue still on the bezel after the protection film is peeled off. (3) You can remove the glue easily. When the glue remains on the bezel or its vestige is recognized,

please wipe them off with absorbent cotton waste or other soft material like chamois soaked with

normal-hexane.