Product Specification
) Preliminary Specifications
(
( V ) Final Specifications
Module 13.3”(13.26”) FHD 16:9 Color TFT-LCD
with LED Backlight design
AU OPTRONICS CORPORATION
Model Name
Note ( )
B133HAN03.0 (H/W:1A)
LED Backlight with driving circuit design
Customer Date
Checked &
Approved by
Date
Approved by Date
Marcus Yen 11/16/2012
Prepared by Date
Note: This Specification is subject to change
without notice.
Katrina Chen
MPBU Marketing Division
AU Optronics corporation
11/15/2012
B133HAN03.0 Document Version : 1.2
1 of 31
Product Specification
AU OPTRONICS CORPORATION
Contents
1. Handling Precautions .............................................................. 4
2. General Description ................................................................ 5
2.1 General Specification ..........................................................................................................................5
2.2 Optical Characteristics ........................................................................................................................6
3. Functional Block Diagram ..................................................... 11
4. Absolute Maximum Ratings................................................... 12
4.1 Absolute Ratings of TFT LCD Module.............................................................................................12
4.2 Absolute Ratings of Environment .....................................................................................................12
5. Electrical Characteristics....................................................... 13
5.1 TFT LCD Module..............................................................................................................................13
5.2 Backlight Unit ...................................................................................................................................14
6. Signal Interface Characteristic.............................................. 17
6.1 Pixel Format Image ...........................................................................................................................17
6.2 Integration Interface Requirement.....................................................................................................18
7. Panel Reliability Test ............................................................ 24
7.1 Vibration Test ....................................................................................................................................24
7.2 Shock Test .........................................................................................................................................24
7.3 Reliability Test...................................................................................................................................24
8. Mechanical Characteristics.................................................... 25
8.1 LCM Outline Dimension...................................................................................................................25
8.1.1 Standard Front View.......................................................................................................................25
9. Shipping and Package ........................................................... 27
9.1 Shipping Label Format......................................................................................................................27
9.2 Carton Pakage....................................................................................................................................28
9.3 Shipping Package of Palletizing Sequence........................................................................................28
10. Appendix............................................................................. 29
10.1 EDID Description............................................................................................................................29
B133HAN03.0 Document Version : 1.2
2 of 31
Product Specification
(Thinning Source IC for
AU OPTRONICS CORPORATION
Record of Revision
Version and Date
0.0 2012/03/27 All First Edition
0.1 2012/04/10 28 EDID(B133HAF01.0) EDID(B133HAN03.0)
0.2 2012/04/18 5 Weight 222g Weight 219g
0.3 2012/05/11 5,6,23,24 Weight 219g
0.4 2012/06/18 23 Reliability Test
0.5 2012/07/11 6 Color support
1.0 2012/08/24 19 LED Power Supply
1.1 2012/9/21 1, 26
1.2 2012/10/8 6
23
Page Old description New Description Remark
Weight 215g
Luminance 340 typ / 289 min
CR TBD
Physical Size Z :2.515 max
Color Coordinates TBD
High temperature storage 7
Low temperature storage -3
16M 8bit
Min 6V
H/W code 0A H/W code 1A
Temperature Range
Operating
12 Storage Temperature
-20, +60
23 High Temperature Operation
60℃
Low Temperature Operation
-20℃
Luminance 350 typ / 300 min
CR 800 typ / 600 min
Physical Size Z :2.465 max
Color Coordinates 1st update
2D drawing update
Reliability Test
0℃
High temperature storage 6
0℃
Low temperature storage -20℃
Color support
262K 6bit
LED Power Supply
Min 5.5V
COG mura)
0 to +50
Storage Temperature
0, +50
High Temperature Operation
50℃
Low Temperature Operation
0℃
0℃
B133HAN03.0 Document Version : 1.2
3 of 31
Product Specification
1. Handling Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input
connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration
or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on
hard surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure
human earth when handling.
7) Do not open nor modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) At the insertion or removal of the Signal Interface Connector, be sure not to rotate
AU OPTRONICS CORPORATION
nor tilt the Interface Connector of the TFT Module.
11) After installation of the TFT Module into an enclosure (Notebook PC Bezel, for
example), do not twist nor bend the TFT Module even momentary. At designing the
enclosure, it should be taken into consideration that no bending/twisting forces are
applied to the TFT Module from outside. Otherwise the TFT Module may be
damaged.
12) Small amount of materials having no flammability grade is used in the LCD module. The
LCD module should be supplied by power complied with requirements of Limited Power
Source (IEC60950 or UL1950), or be applied exemption.
13) Disconnecting power supply before handling LCD modules, it can prevent electric shock,
DO NOT TOUCH the electrode parts, cables, connectors and LED circuit part of TFT
module that a LED light bar build in as a light source of back light unit. It can prevent
electrostatic breakdown.
B133HAN03.0 Document Version : 1.2
4 of 31
Product Specification
2. General Description
B133HAN03.0 is a Color Active Matrix Liquid Crystal Display composed of a TFT LCD panel,
a driver circuit, and LED backlight system. The screen format is intended to support the 16:9
FHD, 1,920(H) x1,080(V) screen and 262k colors ( RGB 6-bits) with LED backlight driving
circuit. All input signals are eDP interface compatible.
B133HAN03.0 is designed for a display unit of notebook style personal computer and
industrial machine.
AU OPTRONICS CORPORATION
2.1 General Specification
The following items are characteristics summary on the table at 25 ℃ condition:
Items Unit Specifications
Screen Diagonal [mm] 336.71
Active Area [mm] 293.472 x 165.078
Pixels H x V 1,920x3(RGB) x 1,080
Pixel Pitch [mm] 0.15285x 0.15285
Pixel Format R.G.B. Vertical Stripe
Display Mode AHVA, Normally Black
White Luminance (ILED=20mA)
(Note: ILED is LED current)
[cd/m2] 350 typ. (5 points average)
300 min. (5 points average)
Luminance Uniformity 1.25 max. (5 points)
Contrast Ratio 700 typ/ 500 min
Response Time [ms] 25 typ / 35 Max
Nominal Input Voltage VDD [Volt] +3.3 typ.
Power Consumption
[Watt] 4.45W max.
(Column Inversion)
Weight [Grams] 215g max
Physical Size
[mm]
Min. Typ. Max.
Length 304.4 304.9 305.4
Width
Thickness
Electrical Interface 2 lane eDP
B133HAN03.0 Document Version : 1.2
190.0 190.5 191.0
- 2.315 2.465
5 of 31
Product Specification
RoHS Compliance
Glass Thickness [mm] 0.3
Surface Treatment Anti-Glare, Hardness 3H
Support Color 262k colors ( RGB 6-bits)
AU OPTRONICS CORPORATION
Temperature Range
Operating
Storage (Non-Operating)
[oC]
[oC]
0 to +50
-20 to +60
RoHS Compliance
2.2 Optical Characteristics
The optical characteristics are measured under stable conditions at 25℃ (Room Temperature) :
Item Symbol
White Luminance
I
LED
=20mA
Viewing Angle
Luminance
Uniformity
Luminance
Uniformity
θR
θL
ψH
ψL
δ5P
δ
13P
Conditions Min. Typ. Max. Unit Note
5 points average
Horizontal (Right)
CR = 10 (Left)
Vertical (Upper)
CR = 10 (Lower)
5 Points
13 Points
300 350 -
80
80
80
80
85
85
85
85
- - 1.25
- - 1.6
-
-
-
-
cd/m
degree
2
1, 4, 5.
4, 9
1, 3, 4
2, 3, 4
Contrast Ratio CR
Cross talk %
500 700 -
4
Response Time TRT Rising + Falling
Red
Rx
Ry 0.316 0.346 0.376
Color /
Chromaticity
Coordinates
Green
Blue
Gx 0.295 0.325 0.355
Gy 0.560 0.590 0.620
Bx 0.123 0.153 0.183
CIE 1931
By 0.096 0.126 0.156
Wx 0.283 0.313 0.343
White
NTSC
B133HAN03.0 Document Version : 1.2
Wy 0.299 0.329 0.359
%
- 25 35
0.566 0.596 0.626
- 52 -
msec
4, 6
4, 7
4, 8
6 of 31
4
Product Specification
=
Maximum Brightness of thirteen points
Mi
nimum Brightness of thirteen points
Maximum Brightness of five
points
=
Minimum Brightness of five points
Note 1: 5 points position (Ref: Active area)
H /4
H /4
AU OPTRONICS CORPORATION
W / 4 W / 4 W / 4 W / 4
W
1 2
H
H /4
H /4
Note 2: 13 points position (Ref: Active area)
W /4
1 0
1 0
H /4
H /4
H
H /4
1
6
3
4
W
W /4
W /4
2
4 5
7
5
W /4
1 0
3
8
1 0
1 3
H /4
1 0
1 1
9
1 2
Note 3: The luminance uniformity of 5 or13 points is defined by dividing the maximum luminance values by the
minimum test point luminance
δ
W5
δ
Note 4: Measurement method
The LCD module should be stabilized at given temperature for 30 minutes to avoid abrupt temperature change
during measuring. In order to stabilize the luminance, the measurement should be executed after lighting
B133HAN03.0 Document Version : 1.2
W13
7 of 31
Product Specification
Field=2
°
Contrast ratio (CR)=
Brightness on the “White” state
Brightness on the “Black” state
AU OPTRONICS CORPORATION
Backlight for 30 minutes in a stable, windless and dark room, and it should be measured in the center of screen.
Photo detector
Note 5： Definition of Average Luminance of White (YL):
Measure the luminance of gray level 63 at 5 points，Y
L (x) is corresponding to the luminance of the point X at Figure in Note (1).
Note 6： Definition of contrast ratio:
Contrast ratio is calculated with the following formula.
= [L (1)+ L (2)+ L (3)+ L (4)+ L (5)] / 5
L
Note 7： Definition of Cross Talk (CT)
CT = | YB – YA | / YA × 100 (%)
Where
YA = Luminance of measured location without gray level 0 pattern (cd/m2)
YB = Luminance of measured location with gray level 0 pattern (cd/m2)
B133HAN03.0 Document Version : 1.2
8 of 31
Product Specification
Note 8: Definition of response time:
The output signals of BM-7 or equivalent are measured when the input signals are changed from “Black” to
“White” (falling time) and from “White” to “Black” (rising time), respectively. The response time interval between
the 10% and 90% of amplitudes. Refer to figure as below.
AU OPTRONICS CORPORATION
"Black"
100%
S
i
90%
g
n
a
l
(
R
e
l
a
t
i
v
e
v
a
l
u
10%
e
)
0%
Tr
Tf
"White""White"
B133HAN03.0 Document Version : 1.2
9 of 31
Product Specification
Note 9. Definition of viewing angle
Viewing angle is the measurement of contrast ratio ≧10, at the screen center, over a 180° horizontal and
180° vertical range (off-normal viewing angles). The 180° viewing angle range is broken down as follows; 90°
(θ) horizontal left and right and 90° (Φ) vertical, high (up) and low (down). The measurement direction is
AU OPTRONICS CORPORATION
typically perpendicular to the display surface with the screen rotated about its center to develop the desired
measurement viewing angle.
B133HAN03.0 Document Version : 1.2
10 of 31
Product Specification
3. Functional Block Diagram
The following diagram shows the functional block of the 13.3 inches wide Color TFT/LCD 30 Pin one lanel
Module
AU OPTRONICS CORPORATION
B133HAN03.0 Document Version : 1.2
11 of 31
Product Specification
4. Absolute Maximum Ratings
An absolute maximum rating of the module is as following:
4.1 Absolute Ratings of TFT LCD Module
Item Symbol Min Max Unit Conditions
AU OPTRONICS CORPORATION
Logic/LCD Drive Voltage
Vin -0.3 +4.0 [Volt] Note 1,2
4.2 Absolute Ratings of Environment
Item Symbol Min Max Unit Conditions
Operating Temperature
Operation Humidity HOP 5 95 [%RH] Note 4
Storage Temperature
Storage Humidity HST
Note 1: At Ta (25℃ )
Note 2: Permanent damage to the device may occur if exceed maximum values
Note 3: LED specification refer to section 5.2
Note 4: For quality performance, please refer to AUO IIS (Incoming Inspection Standard).
TOP 0 +50 [oC] Note 4
TST -20 +60 [oC] Note 4
5 95
Twb=39°C
[%RH]
Note 4
Operating Range
Storage Range
B133HAN03.0 Document Version : 1.2
12 of 31
Product Specification
Voltage
-
90%
10%
5. Electrical Characteristics
5.1 TFT LCD Module
5.1.1 Power Specification
Input power specifications are as follows;
The power specification are measured under 25℃ and frame frenquency under 60Hz
Symble Parameter Min Typ Max Units Note
VDD Logic/LCD Drive
AU OPTRONICS CORPORATION
3.0
3.3 3.6 [Volt]
PDD VDD Power
IDD IDD Current
I
Rush
Inrush Current
VDDrp Allowable
Logic/LCD Drive
- -
- -
- -
- 1.2 [Watt] Note 1
364
2000
[mA] Note 1
[mA]
100 [mV]
p-p
Ripple Voltage
Note 1 : Maximum Measurement Condition：White Pattern at 3.3V driving voltage. (P
Note 2：Measure Condition
Note 2
max=V3.3
x I
white
)
0V
B133HAN03.0 Document Version : 1.2
0.5ms
Vin rising time
3.3V
13 of 31
Product Specification
5.1.2 Signal Electrical Characteristics
Input signals shall be low or High-impedance state when VDD is off.
Signal electrical characteristics are as follows;
Display Port main link signal:
AU OPTRONICS CORPORATION
VCM
VDiff
Fallow as VESA display port standard V1.2
B133HAN03.0 Document Version : 1.2
Min Typ Max unit
RX input DC Common Mode Voltage
Peak-to-peak Voltage at a receiving Device 100 1320 mV
P-P
Display port main link
0 V
14 of 31
Display Port AUX_CH signal:
Product Specification
AU OPTRONICS CORPORATION
Display port AUX_CH
Min Typ Max unit
VCM AUX DC Common Mode Voltage 0
VDiff
Fallow as VESA display port standard V1.2
Display Port V
AUX Peak-to-peak Voltage at a receiving Device 0.4 0.6 0.8
P-P
HPD
signal:
Display port V
HPD
V
V
Min Typ Max unit
V
HPD
HPD Voltage 2.25
Fallow as VESA display port standard V1.2
3.6 V
B133HAN03.0 Document Version : 1.2
15 of 31
5.2 Backlight Unit
5.2.1 LED characteristics
Parameter
Backlight Power
Consumption
Product Specification
AU OPTRONICS CORPORATION
Symbol
PLED - - 3.25
Min Typ Max Units
[Watt]
Condition
(Ta=25℃), Note 1
LED Life-Time
Note 1: Calculator value for reference P
Note 2: The LED life-time define as the estimated time to 50% degradation of initial luminous.
N/A 15K -
= VF (Normal Distribution) * IF (Normal Distribution) / Efficiency
LED
Hour
5.2.2 Backlight input signal characteristics
Parameter
Symbol
Min Typ Max Units Remark
LED Power Supply VLED 5 12.0 21.0 [Volt]
LED Enable Input
High Level
LED Enable Input
VLED_EN
2.5 - 5.5 [Volt]
- - 0.5 [Volt]
Low Level
PWM Logic Input
2.5 - 5.5
[Volt]
High Level
VPWM_EN
PWM Logic Input
- - 0.5
[Volt]
Low Level
(Ta=25℃), Note 2
IF=20 mA
Define as
Connector
Interface
(Ta=25℃)
PWM Input Frequency
PWM Duty Ratio
Note1: Recommend system pull up/down resistor no bigger than 10kohm
FPWM 200 1K 10K
Duty 5 -- 100
B133HAN03.0 Document Version : 1.2
Hz
%
16 of 31
6. Signal Interface Characteristic
6.1 Pixel Format Image
Following figure shows the relationship of the input signals and LCD pixel format.
1
1920
1st Line
1080th Line
R G B R G B
R G B R G B
R G B R G B
R G B R G B
17 of 31
B133HAN03.0 Document Version : 1.2
6.2 Integration Interface Requirement
6.2.1 Connector Description
Physical interface is described as for the connector on module.
These connectors are capable of accommodating the following signals and will be following
components.
Connector Name / Designation For Signal Connector
Manufacturer IPEX or Compatible
Type / Part Number I-PEX 20455-030E-12 or Compatible
Mating Housing/Part Number
I-PEX 20453-030T-11 or Compatible
6.3.2 Pin Assignment
PIN# Signal Name Description
1 NC-RESERVED Reserved for LCD manufacture’s use
2 H_GND High Speed Ground
3 Lane1_N Complement Signal Link Lane 1
4 Lane1_P True Signal Link Lane 1
5 H_GND High Speed Ground
6 Lane0_N Complement Signal Lane 0
7 Lane0_P True Signal Link Lane 0
8 H_GND High Speed Ground
9 AUX_CH_P True Signal Auxiliary Channel.
10 AUX_CH_N Comp Signal Auxiliary Channel.
11 H_GND High Speed Ground
12 LCD_VCC LCD logic and driver power
13 LCD_VCC LCD logic and driver power
14 LCD_Self_Test or NC LCD Panel Self Test Enable
15 LCD_GND LCD logic and driver ground
16 LCD_GND LCD logic and driver ground
17 HPD HPD signal pin
18 BL_GND Backlight ground
19 BL_GND Backlight ground
20 BL_GND Backlight ground
21 BL_GND Backlight ground
22 BL_ENABLE or NC Bright On/Off(Optional)
23 BL_PWM_DIM System PWM signal input for dimming(Optional)
24 NC-RESERVED Reserved for LCD manufacture’s use
25 NC-RESERVED Reserved for LCD manufacture’s use
18 of 31
B133HAN03.0 Document Version : 1.2
Connector
26 BL_PWR Backlight power
27 BL_PWR Backlight power
28 BL_PWR Backlight power
29 BL_PWR Backlight power
30 NC-RESERVED Reserved for LCD manufacture’s use
Pin 30
Note1: Start from right side.
Note2: Input signals shall be low or High-impedance state when VDD is off.
Internal circuit of eDP inputs are as following.
Pin 1
Note1: Input signals shall be low or High-impedance state when VDD is off.6.3 Interface Timing
19 of 31
B133HAN03.0 Document Version : 1.2
6.3.1 Timing Characteristics
Basically, interface timings should match the 1920x1080 /60Hz manufacturing guide line timing.
Parameter Symbol
Min. Typ. Max. Unit
Frame Rate - - 60 - Hz
Clock frequency 1/ T
66.6 72 80 MHz
Clock
Period TV 1100 1130 1080+A
Vertical
Section
Active TVD 1080
Blanking TVB 20 50 A
Period TH 1010 1050 960+B
Horizontal
Section
Active THD 960
Blanking THB 50 90 B
Note 1 : The above is as optimized setting
Note 2 : The maximum clock frequency = (960+B)*(1080+A)*60 < 80MHz
Note 3 : Clock frequency number is for reference, real setting value refer to EDID
T
T
Clock
Line
20 of 31
B133HAN03.0 Document Version : 1.2
6.4 Power ON/OFF Sequence
Display Port panel power sequence:
Display Port AUX_CH transaction only:
21 of 31
B133HAN03.0 Document Version : 1.2
Display Port panel power sequence timing parameter:
Note1: The sink must include the ability to generate black video autonomously. The sink must automatically enable black video
under the following conditions:
-upon LCDVDD power on (with in T2 max)-when the "Novideostream_Flag" (VB-ID Bit 3) is received from the source (at the end
of T9).
-when no main link data, or invalid video data, is received from the source. Black video must be displayed within 64ms (typ)
from the start of either condition. Video data can be deemed invalid based on MSA and timing information, for example.
Note 2: The sink may implement the ability to disable the black video function, as described in Note 1, above, for system
development and debugging purpose.
Note 3: The sink must support AUX_CH polling by the source immediately following LCDVDD power on without causing damage
to the sink device (the source can re-try if the sink is not ready). The sink must be able to respond to an AUX_CH transaction with
the time specified within T3 max.
22 of 31
B133HAN03.0 Document Version : 1.2
Display Port panel B/L power sequence timing parameter:
23 of 31
B133HAN03.0 Document Version : 1.2
7. Panel Reliability Test
7.1 Vibration Test
Test Spec:
Test method: Non-Operation
Acceleration: 1.5 G
Frequency: 10 - 500Hz Random
Sweep: 30 Minutes each Axis (X, Y, Z)
7.2 Shock Test
Test Spec:
Test method: Non-Operation
Acceleration: 220 G , Half sine wave
Active time: 2 ms
Pulse: X,Y,Z .one time for each side
7.3 Reliability Test
Items
Temperature
Humidity Bias
High Temperature
Operation
Low Temperature
Operation
High Temperature
Storage
Low Temperature
Storage
Thermal Shock
Test
ESD
Required Condition Note
Ta= 40℃℃℃℃, 90%RH, 300h
Ta= 50℃℃℃℃, Dry, 300h
Ta= 0℃℃℃℃, 300h
Ta= 60℃℃℃℃, 35%RH, 300h
Ta= -20℃℃℃℃, 50%RH, 250h
Ta=-20℃℃℃℃to 60℃℃℃℃, Duration at 30 min, 100 cycles
Contact : ±8 KV
Air : ±15 KV
Note 1
Note1: According to EN 61000-4-2 , ESD class B: Some performance degradation allowed. No data lost
. Self-recoverable. No hardware failures.
Remark: MTBF (Excluding the LED): 30,000 hours with a confidence level 90%
24 of 31
B133HAN03.0 Document Version : 1.2
8. Mechanical Characteristics
8.1 LCM Outline Dimension
8.1.1 Standard Front View
25 of 31
B133HAN03.0 Document Version : 1.2
8.1.2 Rear View
26 of 31
B133HAN03.0 Document Version : 1.2
9. Shipping and Package
9.1 Shipping Label Format
27 of 31
B133HAN03.0 Document Version : 1.2
9.2 Carton Pakage
9.3 Shipping Package of Palletizing Sequence
28 of 31
B133HAN03.0 Document Version : 1.2
10. Appendix
10.1 EDID Description
Address
HEX
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
20
21
22
23
24
25
26
27
28
29
2A
2B
FUNCTION Value
HEX
Header 00 00000000 0
FF 11111111 255
FF 11111111 255
FF 11111111 255
FF 11111111 255
FF 11111111 255
FF 11111111 255
00 00000000 0
EISA Manuf. Code LSB 06 00000110 6
Compressed ASCII AF 10101111 175
Product Code
hex, LSB first
32-bit ser # 00 00000000 0
00 00000000 0
00 00000000 0
00 00000000 0
Week of manufacture 00 00000000 0
Year of manufacture 16 00010110 22
EDID Structure Ver. 01 00000001 1
EDID revision # 04 00000100 4
Video input def.
Max H image size
Max V image size
Display Gamma
Feature support
(digital I/P, non-TMDS, CRGB)
(rounded to cm)
(rounded to cm)
(=(gamma*100)-100)
(no DPMS, Active OFF, RGB, tmg Blk#1)
Red/green low bits (Lower 2:2:2:2 bits)
Blue/white low bits (Lower 2:2:2:2 bits)
Red x (Upper 8 bits)
Red y/ highER 8 bits 57 01010111 87
Green x 54 01010100 84
Green y 92 10010010 146
Blue x 26 00100110 38
Blue y 0F 00001111 15
White x 50 01010000 80
White y 54 01010100 84
Established timing 1 00 00000000 0
Established timing 2 00 00000000 0
Established timing 3 00 00000000 0
Standard timing #1 01 00000001 1
01 00000001 1
Standard timing #2 01 00000001 1
01 00000001 1
Standard timing #3 01 00000001 1
01 00000001 1
Value Value Note
BIN DEC
2D 00101101 45
30 00110000 48
95 10010101 149
1E 00011110 30
11 00010001 17
78 01111000 120
02 00000010 2
C8 11001000 200
95 10010101 149
9E 10011110 158
29 of 31
B133HAN03.0 Document Version : 1.2
2C
2D
2E
2F
30
31
32
33
34
35
36
Pixel Clock/10000 LSB
37
Pixel Clock/10000 USB
Horz active Lower 8bits
38
Horz blanking Lower 8bits
39
HorzAct:HorzBlnk Upper 4:4 bits
3A
3B
3C
3D
3E
3F
40
41
42
43
44
45
46
47
48
49
4A
4B
4C
4D
4E
4F
50
51
52
53
54
55
56
57
58
59
5A
5B
5C
Vertical Active Lower 8bits
Vertical Blanking Lower 8bits
Vert Act : Vertical Blanking (upper 4:4 bit)
HorzSync. Offset
HorzSync.Width
VertSync.Offset : VertSync.Width
Horz&Vert Sync Offset/Width Upper 2bits
Horizontal Image Size Lower 8bits
Vertical Image Size Lower 8bits
Horizontal & Vertical Image Size (upper 4:4 bits)
Horizontal Border
Vertical Border
Signal
(non-intr, norm, no stero, sep sync, neg pol)
Standard timing #4 01 00000001 1
Standard timing #5 01 00000001 1
Standard timing #6 01 00000001 1
Standard timing #7 01 00000001 1
Standard timing #8 01 00000001 1
(zero for internal LCD)
(zero for internal LCD)
Detailed timing/monitor 00 00000000 0
descriptor #2 00 00000000 0
Detailed timing/monitor 00 00000000 0
descriptor #3 00 00000000 0
01 00000001 1
01 00000001 1
01 00000001 1
01 00000001 1
01 00000001 1
C4 11000100 196
36 00110110 54
80 10000000 128
B8 10111000 184
70 01110000 112
38 00111000 56
1E 00011110 30
40 01000000 64
10 00010000 16
10 00010000 16
3E 00111110 62
00 00000000 0
28 00101000 40
A6 10100110 166
10 00010000 16
00 00000000 0
0F 00001111 15
00 00000000 0
00 00000000 0
00 00000000 0
00 00000000 0
00 00000000 0
00 00000000 0
00 00000000 0
00 00000000 0
00 00000000 0
00 00000000 0
00 00000000 0
00 00000000 0
00 00000000 0
20 00100000 32
00 00000000 0
00 00000000 0
00 00000000 0
18 00011000 24
30 of 31
B133HAN03.0 Document Version : 1.2
5D
5E
5F
60
61
62
63
64
65
66
67
68
69
6A
6B
6C
6D
6E
6F
70
71
72
73
74
75
76
77
78
79
7A
7B
7C
7D
7E
7F
Detailed timing/monitor 00 00000000 0
Manufacture P/N 42 01000010 66 B
Manufacture P/N 31 00110001 49 1
Manufacture P/N 33 00110011 51 3
Manufacture P/N 33 00110011 51 3
Manufacture P/N 48 01001000 72 H
Manufacture P/N 41 01000001 65 A
Manufacture P/N 4E 01001110 78 N
Manufacture P/N 30 00110000 48 0
Manufacture P/N 33 00110011 51 3
Manufacture P/N 2E 00101110 46 .
Manufacture P/N 30 00110000 48 0
Extension Flag 00 00000000 0
FE 11111110 254
00 00000000 0
Manufacture 41 01000001 65 A
Manufacture 55 01010101 85 U
Manufacture 4F 01001111 79 O
0A 00001010 10
20 00100000 32
20 00100000 32
20 00100000 32
20 00100000 32
20 00100000 32
20 00100000 32
20 00100000 32
20 00100000 32
20 00100000 32
descriptor #4 00 00000000 0
00 00000000 0
FE 11111110 254
00 00000000 0
20 00100000 32
0A 00001010 10
Checksum 19 00011001 25
31 of 31
B133HAN03.0 Document Version : 1.2
Loading...