One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
A150XN01 V0
Handling Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth when
handling.
7) Do not open or modify the Module Assembly.
8) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the Interface
Connector of the TFT Module.
9) After installation of the TFT Module into an enclosure, do not twist nor bend the TFT Module even
momentary. At designing the enclosure, it should be taken into consideration that no bending/twisting
forces are applied to the TFT Module from outside. Otherwise the TFT Module may be damaged.
document version 0.3 4/23
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
A150XN01 V0
2. General Description
This specification applies to the 15 inch Color TFT-LCD Semi-Module A150XN01 V0
The display supports the XGA (1024(H) x 768(V)) screen format and 16.2M colors. All input signals are 1 Channel LVDS
interface compatible.
This module does not contain the backlight.
.
2.1 Display Characteristics
The following items are characteristics summary on the table under 25 к condition:
Items Unit Specifications
Active Area [mm]
Pixels H x V
Pixel Pitch [mm]
Pixel Arrangement
Display Mode
Cell Transmittance [%] (8.8)
Contrast Ratio 500:1
Optical ResponseTime [msec] 12 (Typ, on/off)
Nominal Input Voltage VDD [Volt] +3.3 (Typ)
304.128 (H) x 228.096
1024(x3) x 768
0.297 (per one triad) x 0.297
R.G.B. Vertical Stripe
TN mode, Normally White
Power Consumption(Black Pattern) [Watt] 2.5 (Typ)
Weight [Grams] 315 (Typ)
Physical Size (H x V x D) [mm] 316.23(W) x 242.55(H) x 1.9(D) (Typ)
Electrical Interface one Channel LVDS
Surface Treatment Glare type, Hardness 3H
Support Colors 16.2M colors (RGB 6-bits+FRC)
RoHS Compliance RoHS Compliance
document version 0.3 5/23
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
A150XN01 V0
2.2 Optical Characteristics
The optical characteristics are measured under stable conditions at 25к (Room Temperature):
Item Unit Conditions Min. Typ. Max. Note
Horizontal (Right)
Viewing Angle [degree]
Optical Response Time [msec] Rising + Falling
Color / Chromaticity
Coordinates
(CIE 1931)
Cell Transmittance
(At CCFL=mA)
Contrast Ratio 500:1 - 4
[% ]
CR > 10 (Left)
Vertical (Up)
CR > 10 (Down)
White x
White y
(7.8) (8.8) - 2
12
80
80
80
80
0.310
0.330
1
-
3
2
Optical Equipment: BM-5A, BM-7, PR880, or equivalent
Note 1: Definition of viewing angle
Viewing angle is the measurement of contrast ratio Њ10, at the screen center, over a 180° horizontal and 180°
vertical range (off-normal viewing angles). The 180° viewing angle range is broken down as follows; 90° (Ӱ)
horizontal left and right and 90° (ӥ) vertical, high (up) and low (down). The measurement direction is typically
perpendicular to the display surface with the screen rotated about its center to develop the desired measurement
viewing angle.
Note 2: Measurement method
The LCD module should be stabilized at given temperature for 30 minutes to avoid abrupt temperature change
document version 0.3 6/23
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
A150XN01 V0
during measuring. In order to stabilize the luminance, the measurement should be executed after lighting Backlight
for 30 minutes in a stable, windless and dark room.Based on backlight chromaticity (Wx:0.30, Wy:0.31), backlight
luminance 3600nit.
Photo detector
Field=2
50 cm
LCD Panel
Center of the screen
TFT-LCD Module
Note 3: Definition of response time:
The output signals of photo detector are measured when the input signals are changed from “Full Black” to “Full
White” (rising time), and from “Full White” to “Full Black” (falling time), respectively. The response time is interval
between the 10% and 90% of amplitudes. Please refer to the figure as below.
document version 0.3 7/23
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
S
www.panelook.com
Product Specification
A150XN01 V0
AU OPTRONICS CORPORATION
3. Functional Block Diagram
The following diagram shows the functional block of the 15.0 inches wide Color TFT-LCD Module:
LVD
+3.3V
Connector
DC/DC
Converter
I/F + X-PCB
AUO ASIC
LVDS
Receiver
Timing
Controller
Gamma
Correction
G1
Y-Driver IC
TFT-LCD
1024(x3) x 768
Pixels
G768
D1 D3072
-
document version 0.3 8/23
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
A150XN01 V0
4. Absolute Maximum Ratings
Absolute maximum ratings of the module is as following:
4.1 Absolute Ratings of TFT LCD Module
Item Symbol Min. Max. Unit Conditions
Logic/LCD Drive Voltage VDD -0.3 +4.0 [Volt] Note 1,2
4.2 Absolute Ratings of Backlight Unit
Item Symbol Min. Max. Unit Conditions
CCFL Current ICFL - 8.5 [mA] rms Note 1,2
document version 0.3 9/23
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
4.3 Absolute Ratings of Environment
Item Symbol Min. Max. Unit Conditions
Operating Temperature TOP 0 65 [oC]
Operating Humidity HOP 8 90 [%RH]
Storage Temperature TST -20 80 [oC]
Storage Humidity HST 8 90 [%RH]
Note 1: With in Ta= 25к
Note 2: Permanent damage to the device may occur if exceed maximum values
Note 3: For quality performance, please refer to AUO IIS (Incoming Inspection Standard).
A150XN01 V0
Note 3
document version 0.3 10/23
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
V
V
V
V
www.panelook.com
Product Specification
A150XN01 V0
AU OPTRONICS CORPORATION
5. Electrical characteristics
5.1 TFT LCD Module
5.1.1 Power Specification
Input power specifications are as follows:
Symble Parameter Min. Typ. Max. Unit Condition
VDD
IDD VDD current - 600 - [mA]
Irush LCD Inrush Current - 930 - [mA] Vin rising time = 470us
PDD VDD Power
Logic/LCD Drive
Voltage
3.0 3.3 3.6 [Volt] f10%
Vin=3.3V , ˕˿˴˶˾ Pattern,
at 60Hz
2.5 - [Watt]
Vin=3.3V , ˕˿˴˶˾ Pattern,
at 60Hz
Note: Measurement conditions:
+5.0V
+3.3
R1
47K
(High to Low)
Control Signal
SW
+12.0V
C2
1uF/25V
Q3
AO6402
D6
D5
D2S
D1
G
D2SD1D5
D6
R2
1K
VR1
47K
G
C3
0.01uF/25V
Q3
AO6402
F1
VCC
(LCD Module Input)
C1
1uF/16V
3.3
0
470 us
document version 0.3 11/23
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
in rising time
www.panelook.com
Global LCD Panel Exchange Center
V
V
V
V
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
5.1.2 Signal Electrical Characteristics
Input signals shall be low or Hi-Z state when Vin is off
It is recommended to refer the specifications of SN75LVDS82DGG (Texas Instruments) in detail.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
Note2: LVDS Input Signal For Timing Specification
6. Signal Characteristic
6.1 Pixel Format Image
Following figure shows the relationship of the input signals and LCD pixel format.
A150XN01 V0
document version 0.3 13/23
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
6.2 The Input Data Format
CLKIN+
CLKIN-
RIN0 +/-
RIN1 +/-
RIN2 +/-
RIN3 +/-
Note1: Please follow PSWG.
Note2: 8-bit in
Note3:R/G/B data 7:MSB, R/G/B data 0:LSB
OG0OR5OR4OR3OR2OR1OR0
DEVSHS
Rsvd
Product Specification
AU OPTRONICS CORPORATION
OB0OG3OG4OG1OG2OB1OG5
OB5OB3OB4OB2
Current Cycle
A150XN01 V0
OR7OB7OR6OB6OG7OG6
document version 0.3 14/23
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
A150XN01 V0
6.3 Signal Description
The module using a pair of LVDS receiver SN75LVDS82(Texas Instruments) or compatible. LVDS is a differential signal
technology for LCD interface and high speed data transfer device. Transmitter shall be SN75LVDS83(negative edge sampling)
or compatible. The first LVDS port(RxOxxx) transmits odd pixels while the second LVDS port(RxExxx) transmits even pixels.
DF14A-20P-1.25H (HIROSE)
Pin No. Symbol Description
1 VDD Power Supply, 3.3V (typical)
2 VDD Power Supply, 3.3V (typical)
3 VSS Ground
4 VSS Ground
5 Rin0- - LVDS differential data input (R0-R5, G0)
6 Rin0+ + LVDS differential data input (R0-R5, G0)
7 VSS Ground
8 Rin1- - LVDS differential data input (G1-G5, B0-B1)
9 Rin1+ + LVDS differential data input (G1-G5, B0-B1)
17 Rin3- - LVDS differential data input (R6-R7, G6-G7,B6-B7)
18 Rin3+ - LVDS differential data input (R6-R7, G6-G7,B6-B7)
19 VSS Ground
20 VSS Ground
document version 0.3 15/23
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
6.4 Interface Timing
6.4.1 Timing Characteristics
Signal Item Symbol Min Typ Max Unit
Clock TimingClock frequency Tclk 50 65 81 MHz
Hsync Timing
Vsync Timing
Note: DE mode only
Note: Typical value refer to VESA STANDARD
Horizontal active Tdisp(h) 1024 1024 1024 Tclk
Horizontal blanking Tblk(h) 30 320 1024 Tclk
Horizontal period Th 1054 1344 2048 Tck
Vertical active Tdisp(v) 768 768 768 Th
Vertical blanking Tblk(v) 8 38 256 Th
Vertical period Tv 776 806 1024 Th
A150XN01 V0
document version 0.3 16/23
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
6.4.2 Timing Digram
Product Specification
A150XN01 V0
AU OPTRONICS CORPORATION
document version 0.3 17/23
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
6.5 Color Input Data Reference
A150XN01 V0
Color Data Reference
document version 0.3 18/23
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
A150XN01 V0
6.6 Power ON/OFF Sequence
Vin power and lamp on/off sequence is as follows. Interface signals are also shown in the chart. Signals from any system
shall be Hi-Z state or low level when Vin is off.
Power Supply VDD
LVDS Signal
Backlight On
Parameter
10%
T1
90%
T2
T3
VALID
DATA
T4
Power Sequence Timing
Value
Min. Typ. Max.
90%
T5
T6
10%
T7
Unit
T1 0.5 - 10 [ms]
T2 30 40 50 [ms]
T3 200 - - [ms]
T4 100 - - [ms]
T5 0 16 50 [ms]
T6 - - 10 [ms]
T7 1000 - - [ms]
document version 0.3 19/23
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
A150XN01 V0
7. Connector & Pin Assignment
Physical interface is described as for the connector on module.These connectors are capable of accommodating
the following signals and will be following components
.
7.1 TFT LCD Module
7.1.1 Connector
Connector Name / Designation Interface Connector / Interface card
Manufacturer HIROSE
Type Part Number HRS DF14A-20P-1.25H(56)
7.1.2 Pin Assignment
Pin# Signal Name Pin# Signal Name
1
3
5
7
9
11
13
15
17
19
VDD
VSS
Rin0-
VSS
Rin1+
Rin2-
VSS
ClkIN+
Rin3-
VSS
2 VDD
4 VSS
6
8 Rin1-
10 VSS
12 Rin2+
14
16 VSS
18 Rin3+
20 VSS
Rin0+
ClkIN-
document version 0.3 20/23
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
8. Reliability Test
Environment test conditions are listed as following table.
Items Required Condition
Temperature Humidity Bias (THB) Ta= 50, к 80%RH, 240hours
High Temperature Operation (HTO) Ta= 65к, 240hours
Low Temperature Operation (LTO) Ta= 0к, 240hours
High Temperature Storage (HTS) Ta= 80к, 240hours
Low Temperature Storage (LTS) Ta= -10к, 240hours
Drop Test Height: 60 cm, package test
Thermal Shock Test (TST) -10/к 30min, 80/к 30min, 100 cycles
Note 1: The TFT-LCD module will not sustain damage after being subjected to 100 cycles of rapid temperature
change. A cycle of rapid temperature change consists of varying the temperature from -1˃к to 8˃к, and
back again. Power is not applied during the test. After temperature cycling, the unit is placed in normal
room ambient for at least 4 hours before power on.
Note 2: According to EN61000-4-2 , ESD class B: Some performance degradation allowed. No data lost.
Self-recoverable. No hardware failures.
document version 0.3 21/23
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
9. Outline Drawing
Product Specification
A150XN01 V0
AU OPTRONICS CORPORATION
X4X3X2X1X5
Detail F
document version 0.3 22/23
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
.
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
10. Packing Form
Product Specification
A150XN01 V0
AU OPTRONICS CORPORATION
document version 0.3 23/23
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.