Page 1
HEADPHONE AMP
s
2
Page 2
INTRODUCTION 2
UNPACK
HIGHLIGHTS
NOTES 3
CAUTION.....................................3
ICONS.......................................3
DEVICE LAYOUT 4
FRONT PANEL.................................4
REAR PANEL..................................4
OPERATING INSTRUCTION 5
HEADPHONE AMP ..............................5
USE WITH OTHER DEVICE......................5
AFTER-SALE SERVICE 6
GENERAL............................ ........2
......................................2
..................................2
CONTENT
1
2
3
4
5
1
Cop yrigh t
AUN E All Rig hts Res erved .
Aune does not assume any responsibility for errors or omissions in this document or make
any commitment to update the information contained herein.
Page 3
3
2
Situ ati ons t hat t emperatu re is t oo hi gh 40℃ or
too lo w (- 5℃) or humidit y.
Avoi d impact or pl ace h eav y objects on it.
Avoi d any foreig n mat ter i nside the devic e .
( )
Avoid any chemicals like Benzene or Diluents.
Avoid direct sunlight or any heat sources.
Avoi d magnetic d ust y,d o not d isa sse mble or
modi fy.
ICONS
CAUTION
Please avoid the following situations that could cause damage to
your device:
NOTEINTRODUCTION
Thank you for your choosing the S2 Headphone AMP. Please read this guide
at first to know information about aune S2 Headphone AMP.
S2 Headphone AMP is a high-quality advanced headphone amplifier. With a
high voltage drive technology, S2 is designed to drive headphone with
impedance from 32-600ohm, and provide a perfect listening experience.
For more upgrade information please visit: www.auneaudio.com
UNPACK
Your S2 Headphone AMP has been packed safely in a special designed
container. Please keep the container for emergency usage (in case
send back for repair) .
Check your product box for the following items:
S2 Headphone AMP*1
Power supplier*1
5-pin DC power cable*1
AC power cord*1
User’s guide*1
Warranty card*1
HIGHLIGHTS
Separated main body and power supplier design, provide a lower power
supply interference
Light touch switchers, switch signal source easily
Ecellence integrate circuit design for superior audio parameter and
sound quality
S2 Headphone AMP has time-delay and protection circuit, the LED on
front panel will blink a few seconds and S2 will get ready to work after
power connected.
S2 can be set mute just long press input selection switch till LED
extinguished. To cancel the mute, long presses the input selection switch
again, till the LED lightens.When out of service for long term, turn the
volume to minimum, and unplug the headphone.
Plug-in headphone only when S2 was turn on and the volume was set
minimum.
Please use the S2 headphone as the following instructions:
Page 4
5
4
Input source selection switch
Input source selection LED
1/4＂ stereo jack for headphone
Volume controller
RCA jacks for audio signal input
POWER IN--5-pin DC power cable jack
DEVICE LAYOUT
FRONT PANEL
REAR PANEL
DEVICE LAYOUT
Headphone AMP
Connect the supplied AC power cord to the power supply module, then
connect main body and Power supplier with supplied 5-pin DC power
cable
Audio signal output of device such as CD player IPOD and audio DAC
can connect to LINE 1 or LINE 2 RCA jacks on the rear panel of
S2
Touch the input source selection switch on front panel to select right input
source. When input signal was connected to LINE 1 the LED
indicated LINE 1 should lighten
Rotate the volume controller to adjust output volume
， ，
" " " "
" "，
" "
Used as a headphone amp:
Use with other device
We recommend you to use S2 HEADPHONE AMP with high quality audio
signal output device and headphone, for instance, use with aune S1 music
player and Sennheiser HD650 will be a good choice
Page 5
6
Loading...